Not for New Design TSOP12.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Very low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Improved shielding against EMI * Supply voltage: 2.5 V to 5.5 V * Improved immunity against ambient light 1 * Insensitive to supply voltage ripple and noise * Compliant to RoHS Directive 2011/65/EU and in accordance to WEEE 2002/96/EC 2 94 8691 3 Note ** Please see document "Vishay Material Category Policy": www.vishay.com/doc?99902 MECHANICAL DATA DESCRIPTION Pinning: The TSOP12.. series are miniaturized receivers for infrared remote control systems. A PIN diode and a preamplifier are assembled on a lead frame, the epoxy package acts as an IR filter. The demodulated output signal can be directly decoded by a microprocessor. The TSOP12.. is compatible with all common IR remote control data formats. This component has not been qualified according to automotive specifications. 1 = GND, 2 = VS, 3 = OUT PARTS TABLE CARRIER FREQUENCY STANDARD APPLICATION (AGC2/AGC8) 30 kHz TSOP1230 33 kHz TSOP1233 36 kHz TSOP1236 36.7 kHz TSOP1237 38 kHz TSOP1238 40 kHz TSOP1240 56 kHz TSOP1256 BLOCK DIAGRAM APPLICATION CIRCUIT 16832 17170_5 2 VS 3 Input AGC Band pass Demodulator R1 IR receiver VS Circuit 30 k Transmitter with TSALxxxx OUT + VS C1 C OUT GND VO GND 1 PIN Rev. 2.5, 21-Feb-12 Control circuit R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 < R1 < 1 k, C1 > 0.1 F. GND 1 Document Number: 82013 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP12.. www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL VALUE Supply voltage (pin 2) TEST CONDITION VS - 0.3 to + 6 UNIT V Supply current (pin 2) IS 3 mA Output voltage (pin 3) VO - 0.3 to (VS + 0.3) V Output current (pin 3) IO 5 mA Tj 100 C Storage temperature range Tstg - 25 to + 85 C Operating temperature range Tamb - 25 to + 85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Junction temperature Power consumption Soldering temperature Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. VS 2.5 Ev = 0, VS = 3.3 V ISD 0.27 Supply voltage Supply current (pin 2) TYP. MAX. 0.35 UNIT 5.5 V 0.45 mA Ev = 40 klx, sunlight ISH 0.45 mA Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 250 mA d 45 m IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see fig. 1 VOSL Minimum irradiance Pulse width tolerance: tpi - 5/f0 < tpo < tpi + 6/f0, test signal see fig. 1 Ee min. Maximum irradiance tpi - 5/f0 < tpo < tpi + 6/f0, test signal see fig. 1 Ee max. Directivity Angle of half transmission distance 1/2 Transmission distance Output voltage low (pin 3) 0.15 100 mV 0.35 mW/m2 W/m2 30 45 deg TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Optical Test Signal 1.0 (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) 0.9 tpo - Output Pulse Width (ms) Ee t tpi * * tpi VO T 10/f0 is recommended for optimal function Output Signal 1) 2) VOH 16110 7/f0 < td < 15/f0 tpi - 5/f0 < tpo < tpi + 6/f 0 Output Pulse Width 0.8 Input Burst Length 0.7 0.6 0.5 0.4 0.3 = 950 nm, Optical Test Signal, Fig.1 0.2 0.1 0 VOL td 1) tpo 2) 0.1 t 20752 Fig. 1 - Output Active Low Rev. 2.5, 21-Feb-12 1 10 102 103 104 105 Ee - Irradiance (mW/m2) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 82013 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP12.. www.vishay.com Vishay Semiconductors 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see fig. 4) VO VOH VOL t on 4 Ee min. - Threshold Irradiance (mW/m2) Optical Test Signal Ee Correlation with Ambient Light Sources: 2 3.5 10 W/m = 1.4 kLx (Std. illum. A, T = 2855 K) 10 W/m2 = 8.2 kLx (Daylight, T = 5900 K) 3 2 1.5 1 0.5 0 0.01 t t off Wavelength of Ambient Illumination: = 950 nm 2.5 20757 Ton 0.6 0.5 Toff 0.4 0.3 0.2 = 950 nm, Optical Test Signal, Fig. 3 0 0.1 1 20759 10 Ee - Irradiance 100 1000 100 f = 100 Hz 0.9 0.8 f = 10 kHz 0.7 0.6 f = 20 kHz 0.5 0.4 f = 30 kHz 0.3 f = fo 0.2 0.1 0 10 000 1 (mW/m2) 10 100 1000 VsRMS - AC Voltage on DC Supply Voltage (mV) 20753 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 4 - Output Pulse Diagram 500 E - Max. Field Strength (V/m) 1.2 1.0 E e min./Ee - Rel. Responsivity 10 1.0 Ee min. - Threshold Irradiance (mW/m2) Ton, Toff - Output Pulse Width (ms) 0.8 0.1 1 Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Output Function 0.7 0.1 Ee - Ambient DC Irradiance (W/m2) 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 450 400 350 300 250 200 150 100 50 0 0.0 0.7 16925 0.9 1.1 0 1.3 20747 f/f0 - Relative Frequency 1000 1500 2000 2500 3000 f - EMI Frequency (MHz) Fig. 8 - Sensitivity vs. Electric Field Disturbances Fig. 5 - Frequency Dependence of Responsivity Rev. 2.5, 21-Feb-12 500 3 Document Number: 82013 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP12.. www.vishay.com Vishay Semiconductors 0 1 10 20 30 Max. Envelope Duty Cycle 0.9 0.8 0.7 40 0.6 1.0 0.5 0.4 TSOP12.. 0.3 0.2 0.9 50 0.8 60 70 0.7 80 0.1 f = 38 kHz, Ee = 2 mW/m 0 0 20773-1 20 40 60 80 100 120 0.6 Burst Length (number of cycles/burst) Ee min. - Threshold Irradiance (mW/m2) 0.2 0 0.2 0.6 0.4 Fig. 12 - Horizontal Directivity Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length 0 0.3 10 20 30 0.25 40 0.2 1.0 0.9 50 0.1 0.8 60 0.05 0.7 0.15 70 80 0 - 30 - 10 10 30 50 70 90 0.6 Tamb - Ambient Temperature (C) 20755 95 11339p2 0.4 0.2 0 0.2 0.6 0.4 d rel - Relative Transmission Distance Fig. 13 - Vertical Directivity Fig. 10 - Sensitivity vs. Ambient Temperature 1.2 0.2 Ee min. - Sensitivity (mW/m2) S ()rel - Relative Spectral Sensitivity 0.4 d rel - Relative Transmission Distance 95 11340p2 1.0 0.8 0.6 0.4 0.2 0.18 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 750 94 8408 0 850 950 1050 2 1150 - Wavelength (nm) 20756 3 3.5 4 4.5 5 5.5 6 VS - Supply Voltage (V) Fig. 14 - Sensitivity vs. Supply Voltage Fig. 11 - Relative Spectral Sensitivity vs. Wavelength Rev. 2.5, 21-Feb-12 2.5 4 Document Number: 82013 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP12.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The TSOP12.. series is designed to suppress spurious output pulses due to noise or disturbance signals. Data and disturbance signals can be distinguished by the devices according to carrier frequency, burst length and envelope duty cycle. The data signal should be close to the band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP12.. in the presence of a disturbance signal, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. Some examples of disturbance signals which are suppressed are: * DC light (e.g. from tungsten bulb or sunlight) 0 * Continuous signals at any frequency 10 5 15 20 Time (ms) 16920 Fig. 15 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal * Strongly or weakly modulated noise from fluorescent lamps with electronic ballasts (see figure 15 or figure 16) 0 16921 5 10 15 20 Time (ms) Fig. 16 - IR Signal from Fluorescent Lamp with High Modulation TSOP12.. Minimum burst length 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length Maximum number of continuous short bursts/second 1800 Recommended for NEC code yes Recommended for RC5/RC6 code yes Recommended for Sony code yes Recommended for Thomson 56 kHz code yes Recommended for Mitsubisi code (38 kHz, preburst 8 ms, 16 bit) yes Recommended for Sharp code yes Suppression of interference from fluorescent lamps Most common disturbance signals are suppressed Note * For data formats with short bursts please see the datasheet for TSOP11.., TSOP13. Rev. 2.5, 21-Feb-12 5 Document Number: 82013 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Design TSOP12.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 10 0.3 (9.2) 0.65 + 0.10 - 0.15 0.8 max. 30.6 0.5 12.5 0.4 Center of sensitive area 0.5 Area not plane 0.4 + 0.15 - 0.05 2.54 nom. + 0.10 - 0.05 1.4 0.3 3 x 2.54 = 7.62 nom. 4 0.3 5.8 0.3 R 2.75 technical drawings according to DIN specifications Drawing-No.: 6.550-5095.01-4 Issue: 20; 15.03.10 96 12116 Rev. 2.5, 21-Feb-12 6 Document Number: 82013 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000