SUMICON 1600 SERIES RECTANGULAR CONNECTORS _ types: soldering, wrapping, and crimping. Accessories Standard Type General cases and stoppers to diversify the specifications and The SUMICON 1600 series are multi-contact connec- are C case, CA case, CBA case, ST stopper, STA stop-\ tors designed by Hirose. 8, 12, 16, 20, 24, 28, 34, 45 per, and STB stopper. By combining the many options and 60-contact models available (same as the 1300 noted above, the SUMICON 1600 series connectors series). The connector units are available in three meet a wide variety of applications. In the SUMICON 1600 series, the connector unit is facilitate wiring connection. The SUMICON 1600 completely separated from the accessories such as the series are specified in the NTT specifications No.1931. Material and Finish Electrical Characteristics Part Material Finish Glass filled Item Standard Insulator diallylphthalate resin Blue Contact 7mQ or less : - ier Resistance at DCIA Male Terminal Brass Type A: Silver- plated Insulation 1000M or mote Female Terminal Phosphor bronze Type B: Gold~plated Resistance at DC500V . ' Plug Case ABS resin (black) NTT spec: ABS resin, Withstand 2.5PB 6.0/2.0 (color) stan AC1000V for 1 minute Voltage Treatment with chromate Stopper Bracket Steel over zinc plating Current Rating SA Voltage Rating AC300V Wire Wrapping Specifications . AWG 26 28 30 Applicable Applicable 0.41 0.32 0.26 wire wire (mm) Max.coating 0.D.(mm) 0.95 0.75 0.6 . Ordinary Coating Coating Wrapping method wrapping one wrap one wrap Effective number of wrappings about 8 about 8 about 9 oti Numero maepins 2 wrap Ordering Information PW-16 34 Q (1) (2) (3) (4) (5) (1) Shape of terminal opening P: Male terminal S: Female terminal (2) Terminal connection method No sign: Soldering (8) W: Wrapping (3) Series No. 16: 1600 series (4) Number of contacts 34: 34 contacts (5) Serial sign for connector units Provided with a sequence of upper-case alphabetic charac- ters. No sign or sign other than W: Soldering (9) Sequence: No sign, B,C,D,E ... (6) Plating A: Silver-plated B: Goid-plated (7) Signs for accessories C: Plug case A-c oO 0 (6) (7) (8) (9) ST: Stopper bracket with horizontal cable inlet opening J: Jack Case H: Handle DB: Deep bracket Serial signs for accessories Each accessory (C,ST,J,H,DB) is provided with sequence of upper-case alphabetic characters. Sequence: No sign, A,B,C... Accessories, C,ST, or J followed by no sign: Side lock types Accessories, C and ST followed By A: Top touch lock type Note: The space for no sign is filled sequentially. Special specification number For a special specification, ( ) is filled with a serial number, except for the case and bracket, for which the following ap- ply. (01): Bracket only (20): Case only , yy, 111Cross Reference to NTT No. Type NTT No. Short Form HRS No. Part No. Type NTT No. Short Form HRS No, Part No. CN-3320GLWPMSA| 20GLWPMSA |CL216-0247-5-01} P-1620BA-CA(01} CN-5445GJMSA 45GJMSA CL216-0257-9-01 | P-1645BA-STA(01) CN-4028GLWPMSA} 28GLWPMSA |CL216-0249-0-01| P-1628BA-CA(01) CN-6760GJMSA 60GJMSA CL216-0258-1-01| P-1660BA-STA(01) CN-4534GLWPMSA| 34GLWPMSA |CL216-0250-0-01! P-1634BA-CA(01) CN-3320G2JMSA 20G2JMSA | CL216-0292-0-01 IPW-1620BA-STA(01)} CN-5445GLWPMSA| 45GLWPMSA |CL216-0251-2-01! P-1645BA-CA(01) CN-3724G2JMSA 24G2JMSA |CL216-0293-2-01 |PW-1624BA-STA(01) CN-6760GLWPMSA| 60GLWPMSA |CL216-0252-5-01| P-1660BA-CA(01) CN~4028G2JMSA 28G2JMSA =| CL216-0294-5-01 |PW-1628BA-STA(01) Plug CN-3320GLWPFSA| 20GLWPFSA }|CL216-0153-3-01 8-1620A~CA(01) CN-4534G2JMSA 34G2JMSA |CL216-0296-0-01 | PW-1634A-STA(01) GN-3724GLWPFSA| 24GLWPFSA |(CL216-0154-6-01] S-1624A-CA(01) CN-6760G2JMSA 60G2JMSA_ |CL216-0298~6-01 |PW-1660BA-STA(01) Receptacle CN-4028GLWPFSA | 28GLWPFSA |CL216-0155-9-01| S-1628A-CA(01) CN-3320GJFSA 20GJFSA CL216-0151-8-01] S-1620A-STA(01)} CN-4534GLWPFSA| 34GLWPFSA |CL216-0126-0-01| S-1634A-CA(01} CN-3724GUFSA 24GJFSA CL216-0148-3-01| S-1624A-STA(01) CN-5445GLWPFSA; 45GLWPFSA |CL216-0127-3-01| S-1645A-CA(01) CN-4028GJFSA 28GJFSA CL216-0152-0-01| S-1628A-STA(01) CN-6760GLWPFSA | 60GLWPFSA |CL216-0128-6-01] S-1660A-CA(01) CN~4028G2JFSA 28G2JFSA CL216-0313-8-01 | SW-1628A-STA(01) CN-3724GJMSA 24GJMSA CL216~0254-0-01] P-1624BA-STA(01} GN-4534G2JFSA 34G2JFSA CL216-0299-9-01 | SW-1634A-STA(01) Receptacle | CN-4028GJMSA 28GJMSA CL216-0255-3-01| P-1628BA-STA(01) CN-5445G2JFSA 45G2JFSA CL216-0300-6-01 | SW-1645A-STA(01) * CN-4534GJMSA 34GJMSA CL216-0256-6-01| P-1634BA-STA(01) CN~-6760G2JFSA 60G2JFSA CL216~0301-9-01 | SW-1660A-STA(01) Note: NTT Types are ali assembled with connector inserts and plug shells or stopper brackets. 112Soldering Eyelet Pin Connector ( Male Connector Solder Hole Ln! mm No. of A Type G Type Pins HRS No. Part No. HRS No. Part No. 8 | *CL216-0171-5-09 CL216-0177-1 P-1608BA(09) *CL216-0180-6-09 P-1608BG(09) 19 12 | *CL216-0172-8-09 P-1634BA P-1612BA(09) * CL216-0181-9-09 P-1612BG(09) 30 24 16 | *CL216-0173-0-09 P-1616BA(09) * CL216-0182-1-09 P-1616BG(09) 35 29 20 | * CL216-0174-3-09 P-1620BA(09) * CL216-0183-4-09 P-1620BG(09) 33 27 1 24 | * CL216-0175-6-09 P-1624BA(09) + CL216-0184-7-09 P-1624BG(09) 37 31 1 28 | * CL216-0176-9-09 P-1628BA(09) * CL216-0185-0-09 P-1628BG(09) 40 34 11 34 | * CL216-0177-1-09 P-1634BA(09) * CL216-0186-2-09 P-1634BG(09) 45 11 45 | * CL216-0178-4-09 P-1645BA(09) * CL216-0187-5-09 P-1645BG(09) 54 48 11 60 | * CL216-0179-7-09 P-1660BA(09) * CL216-0188-8-09 P-1660BG(09) 67 61 11 *: Standard \ Female Connector r Solder Hole pb __+ : [ 2-2.96 Unit: mm No.of A Type G Type Pin HRS No. Part No. HRS No. Part No. c}D 8 |*CL216-0001-5-09 CL216-0007-1 S-1608A(09) * CL216-0055-4-09 S-1608G(09) 25 S-1634A 12 |*CL216-0002-8-09 S-1612A(09) * CL216-0056-7-09 $-1612G(09) 30 24 16 | * CL216-0003-0-09 S-1616A(09) * CL216-0057-0-09 S-1616G(09) 35 29 20 | * CL216-0004-3-09 S-1620A(09) * CL216-0058-2-09 $-1620G(09) 33 27 24 |%* CL216-0005-6-09 $-1624A(09) * GL216-0059-5-09 $-1624G(09) 37 31 11 28 | * CL216-0006-9-09 S-1628A(09) * CL216-0060-4-09 $-1628G(09) 40 34 11 34 | * CL216-0007-1-09 S$-1634A(09) * CL216-0061-7-09 S-1634G(09) 45 39 11 45 | * CL216-0008-4-09 S-1645A(09) %* CL216-0062-0-09 S-1645G(09) 54 48 1i 60 | * CL216-0009-7-09 S-1660A(09) * CL216-0063-2-09 S-1660G(09) 67 61 11 *: StandardWire Wrapping Pin Connector (Male connector CL216-0204-2 PW-1634BA N 45 6 2-2.98 4.5 a3.5 CT } a i he Wrap Post 0.50.7 14.2 Unit: mm Type A Type G mn HRS No. Part No, HRS No. Part No. Aye pore le 8 * GL216-0198-1-09 PW-1608BA(09) CL216-0216-1-09 PW-1608BG(09) | 26 | 19) 10] 13] 8 12 * CL216-0199-4-09 PW-1612BA(09) CL216-0217-4-09 PW-1612BG(09) | 30 | 24 | 10 | 18] 8 16 *CL216-0200-1-09 PW-1616BA(09) CL216-0218-7-09 PW-1616BG(09) | 35 | 29 | 10 | 23/ 8& 20 * CL216-0201~4-09 PW-1620BA(09) CL216-0219-0-09 PW-1620BG(09) | 33 | 27 | 13 | 21 | 11 24 * CL216-0202-7-09 PW-1624BA(09) CL216-0220-9-09 PW~1624BG(09) | 37 | 31 | 13 | 25 | 11 28 %* CL216-0203-0-09 PW-1628BA(09) CL216-0221-1-09 PW-1628BG(09) | 40 | 34 | 13 | 28 | 11 34 *CL216-0204-2-09 PW-1634BA(09) CL216-0222-4-09 PW-1634BG(09) | 45 | 39 | 13 | 33 | 11 45 %* CL216-0205-5-09 PW-1645BA(09) CL216-0223-7-09 PW-1645BG(09) | 54 | 48 | 13 | 42 | 11 60 * CL216-0206-8-09 PW-1660BA(09) CL216-0224-0-09 PW-1660BG(09) | 67 | 61 | 13 | 55 | 11 *; Standard ; (" remale connctor CL216-0195-3 SW-1634A 114 2-2.94 te P Wrap Post 0.5x0.7 Unit: mm Type A Type G Pn HRS No. Part No. HRS No, Part No. AVP] o}P LE 8 * CL216-0189-0-09 SW-1608A(09) CL216-0207-0-09 SW-1608G(09) 25] 19]10/ 13] 8 12 * GL216-0190-0-09 SW-1612A(09) CL216-0208-3-09 SW-1612G(09) 30] 24/10] 18) 8 16 *CL216-0191-2-09 SW~1616A(09} CL216-0209-6-09 SW-1616G(09) 35 | 29) 10] 23] 8 20 * CL216-0192-5-09 SW-1620A(09) CL216-0210-5-09 SW-1620G(09) 33] 27) 13] 20 [11 24 * CL216-0193-8-09 SW-1624A(09) CL216~0211-8-09 SW-1624G(09) | 37 | 31} 13 | 25 | 14 28 * CL216-0194-0-09 SW-1628A(09) CL216-0212-0-09 SW-~1628G(09) 40 | 34 | 13 | 28 | 11 34 * CL216-0195-3-09 SW-1634A(09) CL216-0213-3-09 SW-16344(09) 45 | 39 | 13 | 33 | 11 45 * CL216-0196-6-09 SW-1645A(09) CL216~0214-6-09 SW-1645G(09) 54] 48) 13 | 42) 11 60 * CL216-0197-9-09 SW-1660A(09) CL216-0215-9-09 SW-1660G(09) 67 | 61) 13) 55 | 17 *; StandardSide Touch Lock Type Plug Shell CL216-0034-420 P-1634A-C (20) Ne > }- Ge} { L, 1, mS a \ + ad ) Unit: mm No.of . HRS No. Part No. A Pin B c | oD E F\G|]H 8 | * CL216-0028-1-20 | P-1608A-C(20}| 29 20 |14.5] 42 7.5 7.5 [12.5] 12.5 12 | *CL216~-0029-4-20 | P-1612A-C(20)| 34 20 |14.5) 43.5 75 9 /13.5)13.5 16 | *CL216-0030-3-20 | P-1616A-C(20)} 39 20 |14.5| 46 7.5 11.5/14.5] 14.5 20 | * CL216-0031-6-20| P-1620A-C(20)| 37 23 |17.5)45.5 11 11 /14.5)14.5 24 | *CL216-0032-9-20| P-1624A-C(20}| 41 23 |17.5|46.5 11 12 | 15} 15 28 | *CL216-0033-1-20 | P-1628A-C(20)| 44 23 |17.5|47.5 11 13 (15.5]15.5 34 | *CL216-0034-4-20| P-1634A-C(20)| 49 23 117.5/50.5 11 16 | 17 | 17 45 | * CL216-0035-7-20| P-1645A-C(20)} 58 23 (18.5/54.5 11 19 118.5) 19.5 60 | *CL216-0036-0-20| P-1660A-C(20)| 71 23 |18.5|59.5 11 24 | 21 | 22 Note: All these products are plug cases only. Order connector units separately. The cases can be used for both male and female connector units. The cases marked with an asterisk ar of standard specifications. Side Touch. Lock Type Receptacle Bracket * : Standard XN ~ CL216-0052~6-01 P-1634A-ST(01) 4 B D LE a= 2-M2,6*0.45x10 Unit: mm Noor HRS No. Part No. Alai|c|loje 8 | *CL216-0046-3-01] P-1608A-ST(01) | 27 | 19 ]13.6| 9.2 [15.5 12 |*CL216-0047-6-01| P-1612A-ST(01) | 32 | 24 /13.6] 9.2 [15.5 16 | *CL216-0048-9-01| P-1616A-ST(01) | 37 | 29 /13.6! 17 115.5 20 | *CL216-0049-1-01] P-1620A-ST(01) | 35 | 27 |16.6] 17 |18.5 24 | *CL216-0050-0-01| P-1624a-ST(01) | 39 | 31/166] 11 |18.5 28 | *CL216-0051-3-01| P-1628A-ST(01) | 42 | 34 l1e6] 11 118.5 34 | *CL216-0052-6-01| P-1634A-ST(01) | 47 | 39 [16.6] 11 [18.5 45 | *CL216-0053-9-01/ P-16454-ST(01) | 56} 48 [16.6] 15 [18.5 60 | *CL216-0054-1-01} P-1660A-ST(01) | 69 | 61 |16.6] 15 [18.5 Note: All these products are stopper brackets only. Order connector units separately. The cases can be used for both male and female con- nector units. The brackets marked with an asterisk are of standard specifications. %*: Standard JCL216-0111-3-20 P-1634A-CA (20) XN A j- Gy B + o| te 2 Unit: mm No.of HRS No. Part No. aleple|lolelerlea 20 | *CL216-0149-6-20 P=1620A-CA(20) a7 | 20 | st | 11 | 41 | 18 [145 24 | *CL216-0147-0-20 P-1624A-CA(20) 41 | 20 | 51 | 11 | 12 | 188] 15 28 | *CL216-0150-5-20 P~1628A-CA(20) 44 | 20 | 53 | 11 | 13 | 20 | 155 34 | *CL216-0111-3-20 P-1634A-CA(20) 49 | 20 | 56 | 11 | 16 [21.8] 17 45 | *CL216-0112-6-20 P-1645A-CA(20) s8 | 20 | 60 | 11 | 10 | 24 | 185 60 | #*CL216-0113-9-20 P~1660A-CA(20) 71 | 20 | 6s | 11 | 24 [265] 21 Note: All these products are Plug cases only. The cases can be used for both male and female connector units marked with an asterisk are of standard specifications. Top Touch Lock Type Stopper Bracket 116 CL216-0123-2-01 P--1634A-STA (01) A B I TCT 1 a I aL, i CQ ax + Q YS &C I I I ( 9.7 2 M2.6x0.45x10 Unit mm No.of Pin HRS No. Part No. A/B 20 *,CL216-0156~1-01 P-1620A-STA(01) | 33 | 27 24 * CL216-0157-4-01 P-1624A-STA(01) 37] 31 28 * CL216-0158-7-01 P~1628A-STA(01) 40 | 34 34 %* CL216-0123-2-01 P-1634A-STA(01) | 45/39 45 * CL216-0124-5-01 P-1645A-STA(01) 541 48 60 %* CL216-0125-8-01 P-1660A-STA(01) 67/61 Note: All these products are stopper brackets only. Order connector units separately. The cases can be used for both male and female connec- tor units. The brackets marked with an asterisk are of standard specifications. *: Standard Order connector units separately. . The cases * Standard t=Side Touch Lock Type Jack Shell (For Extension Cable) N Top Touch CL2i6-0142-7-20 S-1634A-J (20) 1 E 1 oy LL on CT + ey 8 [oo | 1 om) Unit: mm No.of HRS No. Part No. AlBpilc|olelFia!]H 20 | CL216-0139-2-20 | $-1620A-u(20) | 37 | 23 |17.5/45.8| 41 | 14 [a4slias 24 | CL216-0140-1-20 | s-1624a-s(20) | 41 | 23 |17.5/46.5/ 11 | 12 [15 Js 28 | CL216-0141-4-20 | s-1628A-u(20) | 44 | 23 |17.5147.5] 11 | 13 [15.5] 15.5 34 | CL216-0142-7-20 | $-1634A-u(20) | 49 | 23 |17.5/50.5] 11 | 16 [17 [17 45 | CL2i6-0225-2-20 | s-1645a-u(20) | 58 | 23 [18.5/54.5] 11 | 19 [18.5l19.5 60 | CL216-0226-5-20 | s-1660-u(20) | 71 | 23 |is.sl/so.5/ 11 | 24 [21 Jo Note: All these products are jack cases only. Order connector units separately. The cases can be used for female connector units only. { CL216-0325-7 1645STA-DC Lock Type Stopper Bracket ( )) ol ~ g = J) [o,| x Unit mm No.of HRS No, Part No. A Pin 20 | CL216-0321-6 1620STA-DC | 38.3 24 | CL216-0322-9 1624STA-DC | 42.3 28 | CL216-0323-1 1628STA-DC | 45.3 34 | CL216-0324-4 1634STA-DC | 50.3 45 | CL216-0325-7 1645STA-DC | 59.3 60 | GL216-0326-0 1660STA-DC | 72.3SHOULDER-TOUCH LOCK TYPE General The shoulder-touch lock type plug cases are highly re- and operable. liable, lightweight, sturdy, 8,12,and 16-contact models are available. Hirose high-density packaging plug cases, including the top-touch lock type, are available in 8 to 60-contact models. Material and Finish Description Material Finish Plug case Polypropylene resin Black : Treated with chromate Stopper Stee! over zinc plating Plug Shell E B Unit: mm No.of HRS No. Part No. alspicl|olelr CL216-0418-6 pin 1616-CBA 8 | *CL21640416-0 1608-CBA 14] 35 | 40 | 45 7.5 > 12 | *CL216-0417-3-01| 1612-CBA(01) 14) 40 | 41 46 9 7.5 . 16 | *CL216-0418-6 1616-CBA 14 | 45 | 42 | 47 | 11.5) 75 %*: Standard Note: Order connector units separately. The cases can be used for both male and female connector units. The cases marked with an asterisk are of standard specifications. How to Mount ) Connector Unit Stopper . 5.8 M2.6 Screw 2.76 76 CL216-0302-1 1600-STB Note: Mounted on a connector i unit (Each package contains two stoppers) 118 HRS No. Part No. Remark * CL216-0302-1 1600-STB Common for any size *: Standard Note: Order connector units separately. The cases marked with an asterisk are of standard speci- fications.1600 SUMICON CRIMP TYPE CONNECTORS General Cn SUMICON 1600 series are high-performance compact crimp type connectors developed for labor saving in connection work. 8, 12, 16, 20, 24, 34, 45 and 60- contact models are available. All models are compatible with our . previous top-lock type plug cases. For using the connectors separately, easy-to-mount plastic locks are available to expand Ne their functions. Material and Finish r Electrical and Environmental Characteristics ~ Item Standard Part Material Finish Contact Resistance 7mQ or less at DC 1A (contact only) Insulator Glass-containing Blue insulatio u polycarbonate resin UL94V-0 nsulation Resistance a 5,000MQ or more at DC 500V Male Brass Gold-plated : i Terminal Silver-plated Withstand Voltage AC 1,000V for 1minute : ; Female Gold~plated Rating Current 3A Terminal Phosphor bronze Silver-plated Applicable Cable AWG 3 24-28 (Coating 0.D. 1.6 $-0.9) Cable AWG #24 AWG # 26 AWG # 28 Crimping strength ; (Unit: kg or more) {| Crimping 36 24 16 force . . . aN Features J (1) (2) (3) Since this is a press-fit type connector, anyone can perform wiring securely with high reliability. For contact, a two-point contact system is em- ployed for outstanding reliability, It asiso offers su- perior mechanical strength. The Sumicon 1600 Series Press-Fit Type Connec- tors are interchangeable with the conventional sol- der, DIP and lapping type connectors. They are applicable, therfore, to a wider range of applica- tions. (4) (5) To use the connector unit separately, jointly em- ploying an easily installable plastic lock will pre- vent vibrations and/or cable dead weight from un- plugging the connector. The plastic lock, moreov- er, can be used with either center-suspension or panel-mount system. Ail wiring spliced with the connector is hidden completely inside the housing, allowing for perfect insulation. 120Housing (r Lo 22.9 2-2.9 P P ) q f Sp oF cs Oe fh 1s) ae -~ Let S w \ ! 1 1 ony t an J 1 1 o af 2 8 *_ | | a Unit: mm Unit: mm HRS No. No.of] part No. Lielw HRS No. No.of] Bart No. L}|elw Pin Pin * CL216-0335-0 8 PC-1608 25 19 10 * CL216-0344-1 8 SC-1608 25 19 10 *| CL216-0336-3 12 PC-1612 30 | 24 | 10 *]) ~=CL216-0345-4 12 SC-1612 30 | 24 | 10 *| CL216-0337-6 16 PC-1616 35 | 29 | 10 *| CL216-0346-7 16 SC-1616 35 | 29 | 10 *| CL216-0338-9 20 PC-1620 33 | 27 | 13 * CL216-0347-0 20 SC-1620 33 | 27 | 13 *| CL216-0339-1 24 PC-1624 387 | 31 | 13 *| CL216-0348-2 24 $C-1624 37 | 31 | 13 *{ CL216-0340-0 28 PC-1628 40 | 34 | 13 *| CL216-0349-5 28 SC-1628 40 | 34 | 13 *| CL216-0341-3 34 PC-1634 45 | 39 | 13 *| CL216-0350-4 34 SC-1634 45 | 39 | 13 *| CL216-0342-6 45 PC-1645 54 | 48 | 13 *| CL216-0351-7 45 SC-1645 54 | 48 | 13 *| CL216-0343-9 60 PC-1660 67 | 61 | 13 *| CL216-0352-0 60 SC-1660 67 | 61 | 13 \ %*: Standard *: Standard SS Contact {Pin Connector Socket Connector | 17.5 | lL 17.5 | Type HRS No. Part No. Plating Type HRS No. Part No. Plating %* CL216-0331-0 PC-1600-111 Gold * CL216-0333-5 $C-1600-111 Gold Loose Loose * CL216-0332-2 PC-1600-112 Silver * CL216-0334-8 $C-1600-112 Silver CL216-0363-6 PC-1600-211 Gold * CL216-0365-1 SC-1600-211 Gold Chain Chain * CL216-0364-9 PC-1600-212 Silver * CL216-0366-4 SC-1600-212 Silver *: Standard *; Standard Note: Loose-piece terminals are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel 10,000 terminals. contains / 121Tools Type HRS No. Part No. Manual crimping tool CL250-0003~-1 TC-1600-171 Contact extractor CL250-0004-4 TC-1600-21 Hand Crimp Tool TC16001111 Contact Extractor TC1600--21 J 1: Gold-plated 2: Silver-plated Applicable cable 1: AWG # 24-28 1: Loose piece contact 2: Strip contact \ Ordering Information e Housing Contact No.of Pin Series No. Crimp type P:Male, S:Felmale Series No. Crimp type P: Male contact S: Female contact] (4) Both gold-plated and silver-plated terminals are available. Use the gold-plated type in adverse en- vironments. In other environments. we recommend \ Using the Connectors ( (1) Take care when removing the connectors to pull out by the housing and not tug on the wires. (2) The male terminals of the connectors will be bent (3) 122 if the connectors are twisted when being removed. Take care to pull the characters out straight. The plastic locks are sufficiently strong to ensure that the connector engagement will not be loosened by vibration or the weight of the wires. Their strength is not sufficient for other loads. When strength for some other load is required, use the top-touch lock type plug case (common for both solder and wrapping types). (5) For crimping, use a manual crimping device for (6) For plug-in uses, we recommend Sumicon 1600 the economical silver-plated type. low-volume crimping and maintenance. For high- volume crimping. we recommend the automatic crimping machine shown on page 124. series solder or wrapping types for improved func- tionality. )Assembling Procedure rr UC Pin contact Socket contact Crimped state Procedure for Contact Extraction Pin contact housing Low-numbered side After assembling, pull . the wire slightly and make sure if the con- tact is mounted as shown above. ) Socket contact housing (, case of extractinga contact from the housing due to insertion error or circuit change, foliow the steps as shown below. Fig. 1 Extraction A 7 Y Shell > \ N Hold the Contact Extractor as shown in Fig.1, plac- ing the tip of the Extractor on the tip of a contact, then insert it between the contact and the housing. When the tip of the Extractor comes into contact with a stepped part in the housing, the spring will come off from the stepped part with a snap which can be felt. Then, extract the contact by pulling the wire. ~ Fig. 2 4G Ly NN N N (Caution: Pushing the tip of the extractor forcibly before the spring has come off from the stepped part may damage the contact). Above Fig.1 and Fig.2 show how to extract a con- tact from socket housing. The same procedure can be employed to extract a contact from pin housing. 123Hints on Use of Connectors with Respect to Polarity (to prevent mis-insertion of connectors) ("roterzaton of SUMICON 1600 series can be achieved by contact arrangement. The crimp type contacts are designed to float a little, so that the use of a Polarizing In Case of 8,12 and 16 pin 1. When crimp types are used in both the male and female, do not fill all cavities with contacts. Use Polarizing Key at minimum 2 cavities of Socket housing as shown below and do not fill pin con- tacts at the corresponding cavities of male hous- ing. 1. SUMICON 1600 series are naturally polarized in all cavities filled with contacts. When all cavities are not filled, Polarizing Keys shall be inserted in vacant cavities to the minimum for preventing reverse coupling. But when Top Touch Lock Plug Shell is used, Polarizing Keys are not necessary 124 In Case of Multi Pin Type more than 20 pin Key is recommended in order to ensure positive nota ization. 2. When male crimp type is used in combination with solder or wire wrap female type, the connector coupling shall be done corefully not to couple in reverse position. Coupling shall be made by matching of traiangle marks on connector inserts. because Plug Shell has polarized mechanism. 2. When male crimp type is used with some vacant cavities in combination with solder or wire wrap female type, Top Touch Lock Piug Shell is recom- mended.Handle > NX S cr Unit: mm No-of HRS No. PartNo. |A |B |cC]D + 16 | CL216-0135-1 1616-H | 36] 25| 6 | 29 & clse-o196-4 FOME SN OES 34 | cL216-0136-4 | 1634-H | 46| 30| 6 | 39 GY 1634-H RK 4 60 | cL216-0137-7 | 1660-H |68| 30] 8 | 61 Deep Bracket en 18 Unit: mm = 60. 2 i H Not HRS No. Part No. im J 34 | CL216-0138-0 | 1634-DB CL216-0138-0 2-3. 1634-DB Crimp or any Connector Unit How to Mount HRS No. Part No. Molding * CL216-0354-5 4600-LC po *: Standard , Common for solder, wire wrap, 1600LC crimp or any connector unit Polarizing Key. HRS No. Part No. How to Mount %* CL216-0487-9 Polarizing Key *: Standard Polarizing Key this manual. Molding ) Zo : N The polarizing key (material: SC-16 any type of female housing. For handling, see connector polarity (prevention of misinsertion on 124page of ") can be used for Notes on 125Terminal Arrangment and Numbers r \ cr 126 The figure shows a male connector as viewed from the termination side Connector Mounting Hole Dimensions j~- 10 2 x0 40 x 60 m 60 9 Unit: mm No.of A B Cc screw 8 19 113.5] 85 12 24 | 18.5] 8.5 16 29 | 23.5) 8.5 20 27 | 21.5] 11.6 24 31 | 26.5 | 11.5 M2.6 28 34 | 28.5 | 11.5 34 39 | 33.5 | 11.5 45 48 | 42.5] 11.5 60 61 | 65.5 | 11.5SUMICON 1600 SERIES DIP SOLDERING CONNECTORS General (~ > The SUMICON 1600 series are original Hirose rec- tangular dip soldering connectors 8,12,16,20,24,34,45 and 60-contact models are available. All models are compatible with the previous 1600 series in mounting and accessories. \ Features S Allows straight dip soldering onto a PCB, and is 3. effective in PCB-to-PCB and PCB-to-cable con- nection. 4. Suitable for use in interfaces,. being compact and lightweight and meeting high-density packaging requirements. Further cuts interconnection costs when simple locks are used. A wide variety of combinations of connection methods available, e.g., dip soldering, wrapping, and crimping, to meet your requirements. Main Applications Computers, peripherals and terminals, data com- munications equipment, measuring instruments, signal equipment, mobile radio equipment, copi and FAX machine. er Electrical and Environmental Material and Finish Glass-Filled diallyiphtalate resin Brass Type A: Silver-plated Phosphor bronze Type B: Gold-plated Performance Contact 7mQ or less at DC 1A Insulator Resistance Male Terminal Insulation ,-1,000M 2 or higher - Resistance at DC 500V Female Terminal Withstand AC 1,000V for 1 minute Voltage Current capacity 3A Ordering Information (1) 16 34 T 1) (2 (3) ~ 4 5 = Shape of terminal opening P: Male terminal S: Female terminal Terminal connection method D: Dip soldering Series No. 16: 1600 series Number of contacts Serial sign for connector units Provided with sequence of upper-case alphabetic characters. (6) (2) (7) (3) (8) (4) (5) C] A I I sP OD 7 (6) (7) (8) Sequence: No sign, B,C,D,E... Piating A: Silver plated B: Gold plated Signs for accessories SP: Spacer for dip soldering Serial signs for accessories Each accessory is provided with a sequence A of upper-case alphabetic characters. Sequence: No sign, A,B,... S 127 J \ YJ \Y128 Dip Soldering Type Connector XY ( snale Connector Dip Post 0.50.5 A B D I ce 1@ {Ft T 4 7.2 Unit: mm Type A Type G oot A|lBp|[clbpie a HRS No. Part No. HRS No. Part No. 8 *CL216-0388-7-09 | PD-1608BA(09) | CL216-0406-7-09 | PD-1608BG(09) | 25| 19} 10/13] 8 12 | *CL216-0389-0-09 | PD-1612BA(09) | CL216-0407~-0-09 | PD-1612BG(09) | 30 | 24/10] 18] 8 16 | *CL216-0390-9-09 | PD-1616BA(09) | CL216-0408-2-09 | PD-1616BG(09) | 36 | 29/10] 23] 8 20 | *CL216-0391-1-09 | PD-1620BA(09) | CL216-0409-5-09 | PD-1620BG(09) | 33 | 27] 13 | 21} 11 24 | *CL216-0392-4-09 | PD-1624BA(09) | CL216-0410-4-09 | PD-1624BG(09) | 37 | 31 | 13 | 25] 11 CL216-03940 28 | *CL216-0393-7-09 | PD-1628BA(09) | CL216-0411-7-09 | PD-1628BG(09) | 40} 34 | 13] 28] 11 PD-1634BA 34 | *CL216-0394-0-09 | PD-1634BA(09) | CL216-0412-0-09 | PD-1634BG(09) | 45 | 39 | 13 | 33 | 11 45 | *CL216-0395-2-09 | PD-1645BA(09) | CL216-0413-2-09 | PD-1645BG(09) | 54] 48 | 13 | 42 | 11 60 | #*CL216-0396-5-09 | PD-1660BA(09) | CL216-0414-5-09 | PD-1660BG(09) | 67 | 61 | 13 | 55 | 11 * Standard YD (" cemale Connector > A Dip Post 0.5x0.5 B 3.5 D | | +t fA f Cc 8 1@ | [at ; an T 74 | 2-2.99 ~| 7.2 Unit: mm - Type A Type G No.of alelclole Pin HRS No. Part No. HRS No. Part No. 8 * CL216-0379-6-09 SD-1608A(09) | CL216-0397-8-09 | SD-1608G(09) | 25] 19| 10/13] 8 12 | *CL216-0380-5-09 SD-1612A(09) | CL216-0398-0-09 | sD-1612G(09) | 30/24] 10} 18 | 8 16 | *CL216-0381-8-09 SD-1616A(09) | CL216-0399-3-09 | sSD-1616@(09) | 35 | 29 | 10 | 23] 8 20 | *CL216-0382-0-09 SD-1620A(09) | CL216-0400-0-09 | SD-1620G(09) | 33 | 27) 13 | 21 | 11 24 | *CL216-0383-3-09 SD-1624A(09) | CL216-0401-3-09 | SD-1624G@(09) | 37] 31] 13 | 25 | 11 CL216-0385-9 28 | *CL216-0384-6-09 SD-1628A(09) | CL216-0402-6-09 | sD-1628G(09) | 40 | 34 | 13 | 28 | 11. SD-1634A 34 | *CL216-0385-9-09 SD-1634A(09) | CL216-0403-9-09 | SD-1634G(09) | 45| 39/13] 33 | 11 45 | *CL216-0386-1-09 SD-1645A(09) | CL216-0404-1-09 | SD-1645BG(09) | 54| 48/13] 421 11 60 | *CL216-0387-4-09 SD-1660A(09) | CL216-0405-4-09 | sD-1660BG(09) | 67 | 61 | 13 | 55 | 11 *: Standard SDip Spacer 7 HRS No. Part No. Application Connector unit packing * CL216-0419-9 D-1600-SPA 800-S (applicable for models with any number of contacts) j i it st *CL216-0420-8 D~1600-SPB For packing with Connector unit stopper (applicable for models with any number of contacts) % Standard Mounting screws must be supplied by the customer 10 Pin connectors Socket Connector Pin connectors Socket Connector ~ ~ _without Brackets | without Brackerts aaa o ona a dan nrad ~ L : 4 S 274 __ =] D-1600-SPA ; =| D-1600-SPA a ' ' Pood ie po et ; 1 i i are _ P.C.B : i P.C.B Nut M2.6X0.45 Nut (M2.6X0.45) Le Screw M2.6X0.45X12 x Screw (M2.6X0.45 X 12) D-1600SPA aa Male connector with side-lock type stopper bracket Mate connector -- with ST =e ( O; D-1600-SPB Ol ie 4 3 PCB Ime@e) Nut (M2.6X0.45) < Screw (M2.6 X0.45X 12) Female connector with side-lock type stopper bracket Female connector | with ST I 3 ion 10 " D-4600-SPB 1 Sore ' I Lt _3 |__| PCB Nut (M2.6X0.45) = \ Screw (M2.6X0.45X12) ms 2.7 [ts D1600-SPB Male connector with top-touch-lock type stopper bracket Male connector we ne with ST 1 D-1600-SPB La \Ca\ \ ' 3 rT ON eee 1s AX Nut (2.60.45) * Screw (M2.6X0.45X 12) Female connector with top-touch-lock type stopper bracket Female connector with ST . AL a tA rl 126 D-1600-SPB Note 1: The connector unit packaging spacer (SPA) cannot be used for packing with the connector unit stopper bracket. The packaging spacer with connector unit stopper bracket (SPB) cannot be used for packaging the connector unit. Note 2: Provide two spacers (SPA and SPB) for each connector unit. * The dimensions marked with an asterisk (*) are for PCBs of 1.6mm in thickness. How to use connectors (1) (2) When disconnecting, pull it as straight as possible, because the male pins might be damaged if it is twisted. Connectors are available with gold to. be used in adverse environmental conditions and silver- plated pins be used in ordinary conditions. 129r Recommended Dip Soldering Pattern of Connector (mm ) connector unit) on the mating face of the connector unit. When dip soldering the connectors to a PCB, drill holes as shown below. The figures indicate the num- ber of contacts. Signs 4 indicate the V-shaped mark (direction of the Recommended Dip Soldering Pattern of Pin Connector (View of the connector-mounting surface of substrate) 29.0. 24.0 [7825-49-25 +190 +| 6.75 6. 6.757 5.75 | _ 4.25 jo. 25 S710 (g.25 3. 25 1271.00 4.25 3.25 nao 1.751} -th0.75 1.75 1.75 0.75 1.75 1.75 0.75 L715 . O_<1 A | we <j 4 = Ch At a ns + = + ~ atts ot tHH ts 75 PSH eS 175 \ 2-2.9 2-2.9 2-2.9 PD1608 PD1612 PD-1616 -50 3.00 PD1620 PD~1624 PD1628 -00 7.50 0. .50 15.00: N 130 PD-1634 PD1645PD1660 Recommended PC Board Hole Pattern Socket Connector pe ae -1.0 5S D1608 SD-1620 +24 ; 0+| 6.75 6,75 ; 4.25 3.25? 1271.06 1.75 0.75 2.00 ah =A_<1 \Y 44444 WwN S pris 2.00 2-2.9 SD-1612 SD1624 SD1616 10. SD-1628 131132 39. 14, 14,25 es ase | 5. 6.75 re 75 34-1.0 90 . 3.00 7. 50 LS 10. al SD1634 3. 6.25 13. 6. 8.7 1 ee 3. 25 3. | 6. 18, 21, 2.50 -00 7.50 10. 12.50 15.00 10. SD1645 S D-1660 mm . No, Appli- Recommended Mounting Hole of | A B c cable Pin Screw [eg A 8 19 13.5 8.5 re es 12 24 18.5 8.5 f 16 29 23.5 8.5 2 21. . c @ 0 27 1.5 11.5 t 24 31 25.5 11.5 M2.6 2-34 28 34 28.5 11.5 34 39 33.5 11.5 45 48 42.5 11.5 60 61 55.5 11.5 Function Chart 1 7 Top-Touch Lock Side-Touch Lock _ Shoulder-Touch Lock CA Shell Plain Lock Polarizing Key * STA Stopper Bracket ee Crimp Pin Contact ea ST Stopper Bracket , Ll Male Housing CBA Shell [S 0 Y STB Stopper Bracket (9) Handle (Sp Pin Insert Pin Insert p> Pin Insert Crimp Socket Contact Qi > Crimping Female Housing Soldering Eyelet Socket Insert Wire Wrapping _ {| Socket Insert . Socket Insert Straight Dip Soldering * Dust cap is available for STA Stopper Bracket. 133SUMICON 1600 SERIES RIGHT-ANGLE DIP SOLDERING CONNECTORS (MALE) General The SUMICON 1600 series are Hirose right-angle dip type, wrapping type, crimping type, and straight dip soldering type connectors including their accessories. soldering connectors (male). All models are compatible with the existing soldering 20, 28, 34 and 60-contact models are available. Direct dip soldering on a PCB enables conve- nient parallel connection with cable plugs. Suitable as an interface, being lightweight and capable of high-density packaging. Further cuts interconnection costs by using crimp- ing type plugs with plastic locks for simple cable connection, so no cases are needed. A wide variety of connection methods available, e.g., dip soldering, wrapping, and crimping, to meet your requirements. Available with or without a top~touch lock type bracket and side-lock type bracket, offering you many choices for your applications. Highly solvent-resistant, using insulating materials with high heat resistance and chemical-resistance. > Main Applications Electronic equipment such as computers, peripherals and terminals, control equipment, and measuring instru- ments. Electrical and Environmental r Material and Finish Glass-Filled diallylphtalate resin Blue Brass Type A: Silver-plated Type B: Gold-plated Polybutylenephthalate resin Blue(UL94V-0) Steel Treated with chromate over zinc plating Electrical Characteristics Current 3A Insulation Rating Contact Voltage AC 300V Rating Right Angle Contact 10m Q orless at DC 1A Resistance Stopper Bracket Insulation 1000M or higher Resistance at DC 500V Withstand 1,000 Vr.m.s. Voltage for 1 minute ~ 135Ordering Information (1) (2) (3) (4) (5) N 7 P R- 16 34 BA R (1) (2) (8) (4) (5) (6) (7) (8) Shape of terminal opening (6) Plating P: Male terminal Terminal connection method R: Right-angle dip soldering Series No. 16: 1600 series Number of contacts Serial sign for connector units Provided with a sequence of upper-case alphabe- tic characters. (7) (8) A: Silver-plated G: Gold-plated Accessories ST: Side-lock type stopper bracket STA: Top-touch type stopper bracket R: Indicates a connector on which the STA bracket is mounted in the reverse direction against the standard. (the standard refers to the direction in which both 4 marks on the STA bracket and con- nector unit are in the same direction). y, Right Angle Dip Soldering Pin Connectors With Stopper Bracker for Top-Touch Lock Plug Shell NY 136 Unit: mm 14.3 3.5 A 2-% 2.9 ) Dip post0.5x0.5 | | * - ta Cyr oa} 2 N = | tf MO 6 a Vv 3 B 2 c rl SC wd A Type No.of AlB|c Pin HRS No. Part No. 20 CL216-0448-7 * PR-1620BA-STA 27 | 33 | 36 28 CL216-0450-9 * PR-1628BA-STA 84 | 40} 43 34 CL216-0451~1 * PR-1634BA-STA 39 | 45 | 48 CL216-0451-1 60 CL216-0453-7 * PR-1660BA-STA 61 | 67 | 70 PR-T6348A-STA *: Standard Gold plated type are available options.With Stopper Bracket for Side-Touch Lock Plug Shell Unit: mm \ 14.3 3.5 (2.75% Dip Post 0.5x0.5 Type A Not AlBlic HRS No. Part No. 20 CL216-0455-2 * PR-1620BA-ST 27 | 35 | 36 28 CL216-0457-8 %* PR-1628BA-ST 34 | 42 | 43 . 34 CL216-0458-0 * PR-1634BA-ST 39 | 47 | 48 CL216-0458-0 PR-1634BA-ST 60 CL216-0460-2 %* PR-1660BA-ST 61 | 69 | 70 \ . . 3: Standard Gold plated type are available options / Connector Unit Only Without Bracket Unit: mm 2-$2.9 | 14.3 3.5 }~__-} A : ($$ $i i Dip Post 0.5x0.5 na 8 e 10.4 Cc hry tT Type A No.of AlBlic Pin HRS No. Part No. 20 CL216-0461-5 * PR-1620BA 27 | 33 | 36 28 CL216-0463-0 * PR-1628BA 34 | 40 | 43 CL216-0464-3 34 CL216-0464-3 * PR-1634BA 39 | 45 | 48 PR-1634BA 60 CL216-0466-9 * PR-1660BA 61 | 67 | 70 \ *: Standard Gold plated type are available options / 137With Stopper Bracket for Top Touch Lock Plug Shell in Reverse Position N CL216-0498-5 PR-1634BA-STAR How to Use (Example) r 138 Connector Mounting Side PCB Ve ff Doyo PDO L Cf Pd 8 3.5 Unit: mm A 2- 2.9 Post 0.5x0.5 I ; rot o- LF ~~ wl! = oye] 3 g ' oO QO | sf 1 - tJ oe Sm _ 3 ay B [15.7 sf c , r IT iN) < Hf Se Type A Novof Alsplc n HRS No. Part No. 20 | *CL216-0495-7-09 | PR-1620BA-STAR (09) | 27 | 33 | 36 28 | *CL216-0497-2-09 | PR-1628BA-STAR(09) | 34 | 40 | 43 34 | *CL216-0498-5-09 | PR-1634BA-STAR(09) | 39 | 45 | 48 60 | *CL216-0500-5-09 | PR-1660BA-STAR(09) | 61 | 67 | 70 *: Standard Gold plated types are available options. Note: When this type is used the mounting direction of socket insert in plug shell shall be in reverse position against the triangle mark on plug shell. PR-16" ;BUGUSTA With Top Touch Lock Bracket Top Touch Lock Plug Shell ; ~How to Use Right Angle Dip Soldering Connectors (. The standard use of this type is to mount it on the left side of a vertical PC board. (Fig. 1) 8 1 14 No. of pin 7 20 13 Right Angle I Connector : _ Connect Left side of PCB _ Pin No. nnector . Mounting Side Dip Soldering Side / PCB Fig. 1 NY (, It is possible to mount it on the right side of PCB but special caution is necessary to be opposite all pin loca- tions on dip soldering surface. (Fig. 2) Connector Mounting Side Pin No. _. Right Angle Connector __ [; ' Right side of PCB Dip soldering Side \ Fig. 2 139_e When Top Touch Lock Type Plug Shell and Stop- per Bracket are used with mounts on the right side of a PCB, not only the pin locations become Oppo- Exit are upside down. So, the Reverse Mount Stopper Bracket is con- veniet in such case.(Fig.3) site, but also the Lock Release Button and Cable Connector Mounting Side Lock Release Button . AMark 4 Mark [" Right side of PCB OOO A i L | r > ? Le GOs a meee = ' + T+ 3 ttt | tt a lppat os TH oe pt ach : | B\- ; - va DY Il ih FI omtn?ee |. 7: Cable Exit Top Touch I uy P 1 . ! cB Connector with Reverse Lock Plug Shell} Socket Insert ! Mount Stopuer Braker | Fig. 3 Piug Connector j= Right Angle Connector with Reverse Mount Stopper Bracket . io 4. M2.6 screws are recommended to mount Right Angle Dip Soldering Pin Connectors. 5. Please choose PC board thinner than 2.4mm. 6. In extracting plug connector, please pull it up straight out to prevent male pin from bending. r 7. The standard plating is silver but gold is also an available option. 8. Note: The dip soldering pattern on PCB of Right Angle Type and Straight Type are different from each other. 9. Before using a solvent other than trichloroethylene, chlorosene, methanol, isopropanol, or ethyalchol to wash soldered connectors, contact our engineer- ing department. 140Recommended Dip Soldering Pattern r Ne 2-M2.6 hole 27 13.5 rab on 20-61 o on Nn als AS, A a WY Lely 02 1-09 eff: PCB End 2-M2.6 hole iy ~~ on Qo on a ~ a on ~ toatwte, PR-1620B 19.5 14,25 14.25 11.75 | 11.75 8.25 | 9.25 5.75] 6.75 | a hae mt 0.75 | 1.75 mo | a 5 Zz 4.25 34-0 1 J ee 1 tt ie Sr N q 21 -oe are ee +9: + =a = +> roel PCB End 7 {5.5 9.5 | 8 13 10.5 PR-1634B same mark on the connector unit. Note 1. The triangle mark represents the position of the om 34 17 rs a , 11.75 | 11.75 9.25 | 9.25 5.751 6.75 i 3,25/4. 25) 28- 1 sa || |// 2-M2.6 . : hole 25 2 Z| . ne DS Dae t ttt tee O<] ett try + o 2.5 2 0.5 I | 4.5 3 Pin No. PCB End vt 7 (5.5 10.5 | 8 PR-1628B 2-M2.6 hole PCB End 61 1.25 | 3.75 29 Pin No. 6.25] 6.25 8.75 | 8.75 1.25 ; 11. 13.75 13.75 16.25 16.25 18.75 18.75 23.75 21.25 PR-1660B 2. Above pattern is shown from view direction of the connector mounting side. , y 141Recommended Mounting Pattern cr For insertion-soldering in the PCB, drill mounting holes as shown in the figure below. | A . | 2-M2.6hole Post hole ! _- _L AI 6+ + 4+4+4+4++4+444 ; a d 2 : & | fo _x\ |] ba 7 1 lr Pin No. PCB End 7 Nee a eer Connector With top-touch-lock type stopper bracket : A 2-M2.6 hole Post hole | oy rr 4 | c Ott tt al ; A tk p- ete, st : ; x _ t oO - | a __ __ ~~ | n [ | PCB End r fi " 4 Connector With side-lock type stopper bracket 2-M2.6 hole Post hole |___ ig Ee | e+ i++. P<, | XI NAT oT \__Pin No. No. PCB End _--__--_U c 7 Connector Connector Unit Type NX i Le | 7.9 Max 10.4 max r 4 The triangle mark represents the position of the same mark on the connector unit. Above pattern is shown from view direction of the con- nector mounting side. 142 No. of pin A 20 27 28 34 34 39 60 61Function Chart 2 7 Plain Lock Crimp Socket Contact (only for the combination with Right Angle Dip CA shell tee) Connector Unit) Top-Touch Lock 0) 7 *Right-Angle Dip STA a stopper bracket Crimping Female Housing tL > Soldering Eyelet C shell r | Socket Insert Side-Touch Lock ( [3 ; * - Right-Angle Dip ST ight-Angle Di : . : stopper bracket > | Wire Wrapping d La p bes L; ; Socket Insert -> | Straight-Dip Soldering Right-Angle Dip Connector Unit Socket Insert *Dust cap is available for STA stopper bracket. 143