RFM products are now
Murata products.
©2010-2015 by Murata Electronics N.A., Inc.
DR3000 (R) 3/26/15 Page 1 of 5 www.murata.com
Electrical Characteristics, 2.4 kbps On-Off Keyed
Characteristic Sym Notes Minimum Typical Maximum Units
Operating Frequency fO 916.30 916.70 MHz
Modulation Type OOK
Data Rate 2.4 kbps
Receiver Performance (OOK @ 2.4 kbps)
Input Current, 3 Vdc Supply IR3.1 mA
Input Signal for 10-3 BER, 25 °C -100 dBm
Rejection, ±30 MHz RREJ 55 dB
Transmitter Performance (OOK @ 2.4 kbps)
Peak Input Current, 3 Vdc Supply ITP 12 mA
Peak Output Power PO0.75 mW
Turn On/Turn Off Time tON/tOFF 12/6 µs
Sleep to Receive Switch Time (100 ms sleep, -85 dBm signal) tSR 200 µs
Sleep Mode Current IS0.7 µA
Transmit to Receive Switch Time (100 ms transmit, -85 dBm signal) tTOR 200 µs
Receive to Transmit Switch Time tRTO 12 µs
Power Supply Voltage Range Vcc 2.7 3.5 Vdc
Operating Ambient Temperature TA-40 +85 °C
Designed for Short-Range Wireless Data Communications
Supports 2.4-19.2 kbps Encoded Data Transmissions
3 V, Low Current Operation plus Sleep Mode
Ready to Use OEM Module
The DR3000 transceiver module is ideal for short-range wireless data applications where robust operation,
small size and low power consumption are required. The DR3000 utilizes Murata’s TR1000 amplifier-
sequenced hybrid (ASH) architecture to achieve this unique blend of characteristics. The receiver section of
the TR1000 is sensitive and stable. A wide dynamic range log detector provides robust performance in the
presence of on-channel interference or noise. Two stages of SAW filtering provide excellent receiver out-of-
band rejection. The transmitter includes provisions for both on-off keyed (OOK) and amplitude-shift keyed
(ASK) modulation. The transmitter employs SAW filtering to suppress output harmonics, facilitating
compliance with FCC 15.249 and similar regulations. The DR3000 includes the TR1000 plus all configuration
components in a ready-to-use PCB assembly, excellent for prototyping and intermediate volume production
runs.
Absolute Maximum Ratings
Rating Value Units
Power Supply and All Input/Output Pins -0.3 to +4.0 V
Non-Operating Case Temperature -50 to +100 °C
Soldering Temperature (10 seconds) 230 °C
916.50 MHz
Transceiver
Module
DR3000
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
©2010-2015 by Murata Electronics N.A., Inc.
DR3000 (R) 3/26/15 Page 2 of 5 www.murata.com
.70
.25 .20
.165
.70
.10
DR3000 Outline Drawing
Dimensions in inches
DR3000 Pin Out
RF
GND RFIO
AGC/VCC
PK DET
TX IN
RX BBO
RX DATA
CTR0
CTR1
GND
VCC
LPF ADJ
1
2
3
4
58
9
10
11
12
1314
67
GND GND
R3
R4
R8
R1 R2
R6R5
C3
L2
C1
L1
C4 C5
+
ASH Transceiver
20
1
11
10
CTR0 (12)
CTR1 (11)
VCC (9)
LPF ADJ (8)
GND (6, 7, 10)
RFIO
(13)
RF GND
(14)
AGC/VCC
(1)
PK DET
(2)
RX BBO
(3)
RX DATA
(4)
TX IN
(5)
DR3000 Schematic
C6
L3
©2010-2015 by Murata Electronics N.A., Inc.
DR3000 (R) 3/26/15 Page 3 of 5 www.murata.com
Pin Descriptions
Pin Name Description
1 AGC/VCC This pin is connected directly to the transceiver AGCCAP pin. To disable AGC operation, this pin is tied to VCC. To enable AGC
operation, a capacitor is placed between this pin and ground. This pin controls the AGC reset operation. A capacitor between
this pin and ground sets the minimum time the AGC will hold-in once it is engaged. The hold-in time is set to avoid AGC chat-
tering. For a given hold-in time tAGH, the capacitor value CAGC is:
CAGC = 19.1* tAGH, where tAGH is in µs and CAGC is in pF
A ±10% ceramic capacitor should be used at this pin. The value of CAGC given above provides a hold-in time between tAGH and
2.65* tAGH, depending on operating voltage, temperature, etc. The hold-in time is chosen to allow the AGC to ride through the
longest run of zero bits that can occur in a received data stream. The AGC hold-in time can be greater than the peak detector
decay time, as discussed below. However, the AGC hold-in time should not be set too long, or the receiver will be slow in
returning to full sensitivity once the AGC is engaged by noise or interference. The use of AGC is optional when using OOK
modulation with data pulses of at least 30 µs. Active or latched AGC operation is required for ASK modulation and/or for data
pulses of less than 30 µs. The AGC can be latched ON once engaged by connecting a 150 K resistor between this pin and
ground, instead of a capacitor. AGC operation depends on a functioning peak detector, as discussed below. The AGC capacitor
is discharged in the transceiver power-down (sleep) mode and in the transmit modes. Note that provisions are made on the cir-
cuit board to install a jumper between this pin and the junction of C2 and L3. Installing the jumper allows either this pin or Pin 7
to be used for the Vcc supply when AGC operation is not required.
2 PK DET This pin is connected directly to the transceiver PKDET pin. This pin controls the peak detector operation. A capacitor between
this pin and ground sets the peak detector attack and decay times, which have a fixed 1:1000 ratio. For most applications, the
attack time constant should be set to 6.4 ms with a 0.027 µF capacitor to ground. (This matches the peak detector decay time
constant to the time constant of the 0.1 µF coupling capacitor C3.) A ±10% ceramic capacitor should be used at this pin. The
peak detector is used to drive the “dB-below-peak” data slicer and the AGC release function. The AGC hold-in time can be
extended beyond the peak detector decay time with the AGC capacitor, as discussed above. Where low data rates and OOK
modulation are used, the “dB-below-peak” data slicer and the AGC are optional. In this case, the PKDET pin can be left uncon-
nected, and the AGC pin can be connected to VCC to reduce the number of external components needed. The peak detector
capacitor is discharged in the transceiver power-down (sleep) mode and in the transmit modes. See the description of Pin 3
below for further information.
3 RX BBO This pin is connected directly to the transceiver BBOUT pin. On the circuit board, BBOUT also drives the transceiver CMPIN
pin through C3, a 0.1 µF coupling capacitor (tBBC = 6.4 ms). RX BBO can also be used to drive an external data recovery pro-
cess (DSP, etc.). The nominal output impedance of this pin is 1 K. The RX BBO signal changes about 10 mV/dB, with a peak-
to-peak signal level of up to 675 mV. The signal at RX BBO is riding on a 1.1 Vdc value that varies somewhat with supply volt-
age and temperature, so it should be coupled through a capacitor to an external load. A load impedance of 50 K to 500 K in
parallel with no more than 10 pF is recommended. Note the AGC reset function is driven by the signal applied to CMPIN
through C3. When the transceiver is in power-down (sleep) or in a transmit mode, the output impedance of this pin becomes
very high, preserving the charge on the coupling capacitor(s). The value of C3 on the circuit board has been chosen to match
typical data encoding schemes at 2.4 kbps. If C3 is modified to support higher data rates and/or different data encoding
schemes and PK DET is being used, make the value of the peak detector capacitor about 1/3 the value of C3.
4 RX DATA RX DATA is connected directly to the transceiver data output pin, RXDATA. This pin will drive a 10 pF, 500 K parallel load. The
peak current available from this pin increases with the receiver low-pass filter cutoff frequency. In the power-down (sleep) or
transmit modes, this pin becomes high impedance. If required, a 1000 K pull-up or pull-down resistor can be used to establish
a definite logic state when this pin is high impedance (do not connect the pull-up resistor to a supply voltage higher than 3.5
Vdc or the transceiver will be damaged). This pin must be buffered to successfully drive low-impedance loads.
5 TX IN The TX IN pin is connected to the transceiver TXMOD pin through a 4.7 K resistor on the circuit board. Additional series resis-
tance will often be required between the modulation source and the TX IN pin, depending on the desired output power and
peak modulation voltage (3.3 K typical for a peak modulation voltage of 3 volts). Saturated output power requires about 450 µA
of drive current. Peak output power PO for a 3 Vdc supply is approximately:
PO = 4.8*((VTXH – 0.9)/(RM + 4.7))2, where PO is in mW, peak modulation voltage VTXH is in volts and external modulation
resistor RM is in kilohms
This pin must be held low in the receive and sleep modes. Please refer to section 2.9 of the ASH Transceiver Designer’s Guide
for additional information.
6 GND This is a ground pin.
7 GND This is a ground pin.
©2010-2015 by Murata Electronics N.A., Inc.
DR3000 (R) 3/26/15 Page 4 of 5 www.murata.com
Data In
Data Out
3 VdcR/T
2.4 kbps Application Circuit
3.3 K
12345
89101112
13
14
DR3000
6
7
Data In
Data Out
3 VdcR/T
19.2 kbps Application Circuit
3.3 K
12345
6
7
89101112
DR3000
33 K
13
14
Pin Name Description
8 LPF ADJ This pin is the receiver low-pass filter bandwidth adjust, and is connected directly to the transceiver LPFADJ pin. R6 on the cir-
cuit board (330 K) is connected between LPFADJ and ground will be in parallel with any external resistor connected to LPF
ADJ. The filter bandwidth is set by the parallel resistance of R6 and the external resistor (if used). The equivalent resistor value
can range from 330 K to 820 ohms, providing a filter 3 dB bandwidth fLPF from 4.4 kHz to 1.8 MHz. The 3 dB filter bandwidth is
determined by:
fLPF = 1445/ (330*RLPF/(330 + RLPF)), where RLPF is in kilohms, and fLPF is in kHz
A ±5% resistor should be used to set the filter bandwidth. This will provide a 3 dB filter bandwidth between fLPF and 1.3* fLPF
with variations in supply voltage, temperature, etc. The filter provides a three-pole, 0.05 degree equiripple phase response. The
peak drive current available from RXDATA increases in proportion to the filter bandwidth setting. As shipped, the transceiver
module is set up for nominal 2.4 kbps operation. An external resistor can be added between Pin 6 and ground to support higher
data rates. Preamble training times will not be decreased, however, unless C3 is replaced with a smaller capacitor value (see
the descriptions of Pins 2 and 3 above). Refer to sections 1.4.3, 2.5.1 and 2.6.1 in the ASH Transceiver Designer’s Guide for
additional information on data rate adjustments.
9 VCC This is the positive supply voltage pin for the module. The operating voltage range is 2.7 to 3.5 Vdc. It is also possible to use
Pin 1 as the Vcc input. Please refer to the Pin 1 description above.
10 GND This is the supply voltage return pin.
11 CTR1 CTR1 is connected to the CNTRL1 control pin on the transceiver. CTR1 and CTR0 select the transceiver operating modes.
CTR1 and CTR0 both high place the unit in the receive mode. CTR1 and CTR0 both low place the unit in the power-down
(sleep) mode. CTR1 high and CTR0 low place the unit in the ASK transmit mode. CTR1 low and CTR0 high place the unit in
the OOK transmit mode. CTR1 is a high-impedance input (CMOS compatible). This pin must be held at a logic level; it cannot
be left unconnected. At turn on, the voltage on this pin and CTR0 should rise with VCC until VCC reaches 2.7 Vdc (receive
mode). Thereafter, any mode can be selected.
12 CTR0 CTR0 is connected to the CNTRL0 control pin on the transceiver CTR0 is used with CTR1 to control the operating modes of
the transceiver. CTR0 is a high-impedance input (CMOS compatible). This pin must be held at a logic level; it cannot be left
unconnected. At turn on, the voltage on this pin and CTR1 should rise with VCC until VCC reaches 2.7 Vdc (receive mode).
Thereafter, any mode can be selected.
13 RFIO RFIO is the RF input/output pin. A matching circuit for a 50 ohm load (antenna) is implemented on the circuit board between
this pin and the transceiver SAW filter transducer.
14 RF GND This pin is the RF ground (return) to be used in conjunction with the RFIO pin. For example, when connecting the transceiver
module to an external antenna, the coaxial cable ground is connected this pin and the coaxial cable center conductor is con-
nected to RFIO.
©2010-2015 by Murata Electronics N.A., Inc.
DR3000 (R) 3/26/15 Page 5 of 5 www.murata.com
Item Reference Description Value Quanitity
1 U1 TR1000 ASH Transceiver 916.5 MHz 1
2 C1, C4, C6 Capacitor SMT 0603 100 pF ±10% 3
3 C3 Capacitor SMT 0603 0.1 µF ±10% 1
4 C5 Capacitor E1A-B 0805 4.7 µF ±10% 1
5 R1 Resistor Chip 0603 270 K ±5% 1
6 R2 Resistor Chip 0603 330 K ±5% 1
7 R3 Resistor Chip 0603 10 K ±1% 1
8 R4 Resistor Chip 0603 100 K ±1% 1
9 R5 Resistor Chip 0603 4.7 K ±5% 1
10 R6 Resistor Chip 0603 330 K ±5% 1
11 L1 Inductor Chip 0603 10 nH ±5% 1
12 L2 Inductor Chip 0603 100 nH ±10% 1
13 L3 Fair-Rite Bead 0603 2506033017YO 1
14 PCB Printed Circuit Board 400-1526-004x1 1
- C2 Not Used N/A 0
Note: Preliminary specitications, subject to change without notice.
DR3000 Bill of Materials