1
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Functional Diagram
Features
Ultra-Low Noise:
-231 dBc/Hz FOM Integer Mode
-227 dBc/Hz FOM Fractional Mode
Ultra Low Spurious Emissions:
- Less Than 60 dBc Fractional Spurious
Differential Phase Detector Input
14-bit Reference Frequency Divider
Lock Indicator Output
Phase Measurement Capability
GPIO (General Purpose Input/Output) Test Pin
Cycle Slip Prevention Support with HMC984LP4E
24 pin, 4 x 4 mm, LP4E Package
Typical Applications
The HMC984LP4E is suitable for:
•Test Equipment
•Portable Instruments
•High Performance Fractional-N Frequency
Synthesizers with Ultra Low Spurious Emissions
•Military
General Description
HMC984LP4E is a high-performance, ultra-low phase
noise, SiGe BiCMOS Phase-Frequency Detector
and Charge Pump targeted to be used together with
the HMC983LP5E (Fractional Frequency Divider) to
together form a high performance, low noise, ultra low
spurious emission fractional-N frequency synthesizer.
Although best performance and maximum features are
achieved when used together with the HMC983LP5E,
the HMC984LP4E can also be used as a stand-alone,
low phase noise phase frequency detector.
The HMC984LP4E can receive differential VCO input,
and a reference frequency as high as 150 MHz. It
features a 14-bit reference frequency R-Divider, and
automatic and/or congurable Lock Detect Indicator,
as well as integrated CSP (Cycle Slip Prevention)
capability, when used together with the HMC983LP5E,
that signicantly improves frequency lock time.
Integrated Charge Pump phase swap option enables
seamless interfaced to VCOs and active loop lters
with inverted polarity.
Additional features include adjustable Charge Pump
gain and offset current that improve linearity and
performance, and a Soft Reset feature that resets all
register to default values without having to perform a
power-cycle.
The HMC984LP4E is housed in a compact 24 pin 4x4
mm LP4 package.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
Product covered by US and Foreign Patents including US Pat. No. 8,531,217.
2
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Table 1. Electrical Specications
TA = +25 °C, AVDD, RVDD, VDDPD1, VDDPD2, DVDD = 3 V; VCCPD, VPPCP, VDDCP = 5 V; GND = 0 V
Parameter Conditions Min. Typ. Max. Units
Ref. Input Characteristics
Frequency Range DC 50 350 MHz
Ref. Input Power Range 50 Ω Source 612 dBm
Ref. Input Impedance 100||3 Ω||pF
Ref/-Divider Range (14-bit) 116383
Phase Detector (PD)
PD Input Internal Pull-Up Resistance VCOp, VCOn, Each Side 50 Ω
PD Input Current VCOp, VCOn, 2.5 mA Steps 12.5 15 17.5 mA
PD Input Voltage Swing Single-Ended Peak-to-Peak 625 750 875 mV
Fractional Mode
Phase Detector Frequency
12 dBm Sine-Wave Input, Mode A & B DC 50 125 MHz
2 dBm Square-Wave Input, Mode A & B DC 50 90 MHz
Integer Mode
Phase Detector Frequency
12 dBm Sine-Wave Input DC 50 175 MHz
2 dBm Square-Wave Input DC 50 150 MHz
Charge Pump (CP)
CP Output Current 7-bit Programmable, 20 uA/Step, Charge
Pump Gain = CP Current/2π Amps/rad 0.02 2.5 mA
CP HiK See “Charge Pump High Gain (HiK)
Mode” section 3.5 6 mA
Offset Current 7-bit Programmable,5 uA/Step 5635 µA
Phase noise [1]
Floor Figure of Merit (FOM)
Integer Mode -230 dBc/Hz
Fractional Modes A & B -227 dBc/Hz
HiK Integer Mode -232 dBc/Hz
HiK Fractional Mode A -230 dBc/Hz
HiK Fractional Mode B -229 dBc/Hz
Flicker Figure of Merit (FOM)
Integer Mode -269 dBc/Hz
Fractional Modes A & B -267 dBc/Hz
HiK Integer Mode -268 dBc/Hz
HiK Fractional Mode A -266 dBc/Hz
HiK Fractional Mode B -266 dBc/Hz
Spurious [1]
Integer Boundary Spurs @ 2.1 GHz Frequency offsets less than loop band-
width FPD=50 MHz, Mode A -60 -55 dBc
Integer Boundary Spurs @ 2.1 GHz Frequency offsets less than loop band-
width FPD=50 MHz, Mode B -70 -65 dBc
1/2 Integer Boundary Spurs FPD=50 MHz -75 -70 dBc
1/3 Integer Boundary Spurs FPD=50 MHz -85 -80 dBc
[1] Measured with HMC983LP5E/HMC984LP4E as fractional-N synthesizer chip set.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 3
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Table 1. Electrical Specications
TA = +25 °C, AVDD, RVDD, VDDPD1, VDDPD2, DVDD = 3 V; VCCPD, VPPCP, VDDCP = 5 V; GND = 0 V
Parameter Conditions Min. Typ. Max. Units
1/5 Integer Boundary Spurs Fpd=50 MHz -85 dBc
Logic Inputs
VIH Input High Voltage DVDD - 0.4 V
VIL Input Low Voltage 0.4 V
Logic Outputs
VOH Output High Voltage DVDD- 0.4 V
VOL Output Low Voltage 0.4 V
DC Load 1.5 mA
Serial Port
Serial Port Clock Frequency 30 MHz
Power Supplies
AVDD, RVDD Analog Supplies, AVDD should equal
DVDD 2.8 33.3 V
VCCPD 5 V Analog Supply for PD 4.5 55.5 V
VPPCP CP Analog Supply 4.5 55.5 V
VDDCP CP Digital Supply 4.5 55.5 V
DVDD, VDDPD1, VDDPD2 Digital Supplies 2.8 33.3 V
Current Consumption
IDD- Total Current Consumption 123.6 mA
I-AVDD (3 V) AVDD Current 4.8 mA
I-RVDD (3 V) Reference Path Current 22 mA
I-VCCPD (5 V) PD Current 83.5 mA
I-VDDPD1 (3 V) PD Digital Supply Current 2.7 mA
I-VDDPD2 (3 V) PD Digital Supply Current 2.7 mA
I-VPPCP (5 V) CP Analog Supply Current 3mA
I-VDDCP (5 V) CP Digital Supply Current 2.9 mA
I-DVDD (3 V) Total DVDD Current 2mA
Bias Reference Voltage[2] Measured with 10 GΩ Volt Meter 1.58 1.72 1.86 V
Continued...
[2] Bias voltage cannot drive external load. It must be measured with a 10 GΩ voltmeter such as Agilent 34410A. A typical 10 MΩ Digital Volt Meter
will read erroneously.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
4
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
TYPICAL PERFORMANCE CHARACTERISTICS
-269.5
-269
-268.5
-268
-267.5
-267
-266.5
-266
-50 -25 0 25 50 75 100
FLICKER FOM (dBc/Hz)
TEMPERATURE (C)
Integer Mode
Mode B
Hi K Mode B
Hi K Integer Mode
Figure 1. HMC984LP4E & HMC983LP5E
PLL Flicker FOM vs Temperature [1]
Figure 2. HMC984LP4E & HMC983LP5E
PLL Floor FOM vs Temperature [1]
-233
-232
-231
-230
-229
-228
-227
-226
-50 -25 0 25 50 75 100
FLICKER FOM (dBc/Hz)
TEMPERATURE (C)
Integer Mode
Mode B
Hi K Mode B
Hi K Integer Mode
Figure 3. HMC984LP4E & HMC983LP5E
PLL Flicker FOM vs Frequency [1]
-269.5
-269
-268.5
-268
-267.5
-267
-266.5
-266
-265.5
12345678
FLICKER FOM (dBc/Hz)
FREQUENCY(GHz)
Integer Mode
Mode A
Mode B
Hi K Integer Mode
Hi K Mode B Hi K Mode A
Figure 4. HMC984LP4E & HMC983LP5E
PLL Floor FOM vs Frequency [1]
-233
-232
-231
-230
-229
-228
-227
-226
12345678
FLICKER FOM (dBc/Hz)
FREQUENCY(GHz)
Integer Mode
Mode A
Mode B
Hi K Integer Mode
Hi K Mode B
Hi K Mode A
Figure 5. HMC984LP4E & HMC983LP5E
PLL Flicker FOM vs Reference Power [1]
-268.5
-268
-267.5
-267
-266.5
-266
-265.5
-265
-264.5
-15 -10 -5 0 5 10 15
FLICKER FOM (dBc/Hz)
REFERENCE POWER (dBm)
Mode B
Hi K Mode B
Integer Mode
Hi K Integer Mode
Figure 6. HMC984LP4E & HMC983LP5E
PLL Floor FOM vs Reference Power [1]
-233
-232
-231
-230
-229
-228
-227
-226
-225
-15 -10 -5 0 5 10 15
FLOOR FOM (dBc/Hz)
REFERENCE POWER (dBm)
Mode B
Hi K Mode B
Integer Mode
Hi K Integer Mode
[1] Crystal frequency = 100 MHz, PFD frequency = 50 MHz, Active Loop Filter with 220 KHz Bandwidth. Measured at 4101 MHz in fractional mode
and 4100 MHz in integer mode.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 5
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Figure 7. HMC984LP4E & HMC983LP5E
PLL Flicker FOM vs CP Current [2]
-266
-265
-264
-263
-262
-261
-260
-259
0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5
FLICKER FOM (dBc/Hz)
CHARGE PUMP CURRENT (mA)
Figure 8. HMC984LP4E & HMC983LP5E
PLL Floor FOM vs CP Current [2]
-228
-226
-224
-222
-220
-218
0.5 0.75 1 1.25 1.5 1.75 2 2.25 2.5
FLOOR FOM (dBc/Hz)
CHARGE PUMP CURRENT (mA)
Figure 9. HMC984LP4E & HMC983LP5E
PLL Flicker FOM vs CP Voltage [3]
-270
-265
-260
-255
-250
-245
-240
-235
-230
012345
FLICKER FOM (dBc/Hz)
CHARGE PUMP VOLTAGE (V)
Mode B
Hi K Mode B
Integer Mode
Hi K Integer Mode
Figure 10. HMC984LP4E & HMC983LP5E
PLL Floor FOM vs CP Voltage [3]
-235
-230
-225
-220
-215
-210
-205
-200
-195
012345
FLOOR FOM (dBc/Hz)
CHARGE PUMP VOLTAGE (V)
Mode B Hi K Mode B
Integer Mode Hi K Integer Mode
Figure 11. HMC984LP4E & HMC983LP5E
PLL Performance at 7000.01 MHz [4]
-180
-160
-140
-120
-100
-80
-60
10
2
10
3
10
4
10
5
10
6
10
7
10
8
PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
Figure 12. HMC984LP4E & HMC983LP5E
PLL Performance at 4100.01 MHz [5]
-180
-160
-140
-120
-100
-80
-60
10
2
10
3
10
4
10
5
10
6
10
7
10
8
PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
[2] PLL operated in Mode B, CP Votage = 2.5 V, Active Loop Filter with 220 kHz bandwidth used
[3] Charge Pump Current = 2.5 mA
[4] Crystal frequency=100MHz, PD frequency=50MHz, CP current=2.5mA, CP offset current=255 µA, Loop bandwidth = 87 kHz, PLL in Mode B.
[5] Reference frequency=100 MHz, PD frequency=50 MHz, CP current=2.5 mA, CP offset current=280 µA, Loop bandwidth = 87 kHz, PLL in Mode B.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Figure 13. HMC984LP4E & HMC983LP5E
PLL Performance at 2100.01 MHz [6]
-180
-160
-140
-120
-100
-80
-60
10
2
10
3
10
4
10
5
10
6
10
7
10
8
PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
Figure 14. HMC984LP4E & HMC983LP5E [6]
Figure 15. HMC984LP4E & HMC983LP5E PLL
In Band Fractional Spurs vs. Offset Current [8]
-120
-100
-80
-60
-40
-20
-120
-100
-80
-60
-40
-20
-800 -600 -400 -200 0 200 400 600 800
4400 MHz
4700 MHz
5000 MHz
INBAND SPUR AT 15 kHz OFFSET (dBc/Hz)
PHASE NOISE (dBc/Hz)
OFFSET CURRENT (mA)
Figure 16. HMC984LP4E & HMC983LP5E
PLL Floor FOM vs. RF Input Power
-233
-232
-231
-230
-229
-228
-227
-226
-30 -25 -20 -15 -10 -5 0 5 10
FLOOR FOM (dBc/Hz)
RF INPUT POWER (dBm)
Hi K Integer Mode
Integer Mode
Hi K Mode A
Hi K Mode B
Mode B
Mode A
Figure 17. HMC984LP4E & HMC983LP5E
PLL Flicker FOM vs. RF Input Power
-268.5
-268
-267.5
-267
-266.5
-266
-265.5
-265
-264.5
-30 -25 -20 -15 -10 -5 0 5 10
FLICKER FOM (dBc/Hz)
RF INPUT POWER (dBm)
Hi K Integer Mode
Integer Mode
Hi K Mode A
Hi K Mode B
Mode B
Mode A
Figure 18. HMC984LP4E & HMC983LP5E
PLL Two-Way Auto Frequency Sweep [9]
6400
6500
6600
6700
6800
6900
7000
0 5 10 15 20
FREQUENCY (MHz)
TIME (ms)
-180
-160
-140
-120
-100
-80
10
2
10
3
10
4
10
5
10
6
10
7
10
8
PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
Calculated PLL Integer Mode
Calculated PLL Mode B
Measured Mode B
Measured Integer Mode
Simulated Integer Mode
Simulated Mode B
[6] Crystal frequency=100 MHz, PFD frequency=50 MHz, CP current=2.5 mA, CP offset current=280 µA, Loop bandwidth = 87 kHz, PLL Mode
[7] Measured at 7 GHz in Integer Mode and 7.001 GHz in Fractional mode B. PD Frequency = 50 MHz, and loop lter BW = 87 kHz. Simulated results
were obtained using Hittite PLL Design software.
[8] Active Loop lter bandwidth 150 kHz, measured at 10 kHz offset, PFD Frequency=50 MHz. Offset polarity should be positive for inverting
congurations and negative otherwise.
[9] 50 MHz PFD
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 7
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Figure 19. HMC984LP4E & HMC983LP5E PLL
One-Way Triggered Frequency Sweep [10]
6400
6500
6600
6700
6800
6900
7000
0 200 400 600 800 1000
FREQUENCY (MHz)
TIME (ms)
Figure 20. HMC984LP4E & HMC983LP5E PLL
Floor FOM Vs. Sine-Wave Ref Input Level [11]
-230
-225
-220
-215
-210
-15 -10 -5 0 5
FLOOR FOM (dBc/Hz)
REFERENCE POWER (dBm)
100 MHz
12.5 MHz
25 MHz
50 MHz
Figure 21. HMC984LP4E & HMC983LP5E PLL
Floor FOM Vs Square-Wave Ref Input Level [11]
-228
-226
-224
-222
-220
-218
-216
-15 -10 -5 0 5
FLOOR FOM (dBc/Hz)
REFERENCE POWER (dBm)
100 MHz
12.5 MHz
25 MHz
50 MHz
Figure 22. HMC984LP4E & HMC983LP5E
PLL Reference Input Return Loss [12]
-16
-14
-12
-10
-8
-6
0 100 200 300 400 500 600
RETURN LOSS (dB)
FREQUENCY (MHz)
[10] Using 10 Hz external trigger. PFD frequency = 10 MHz. Measured with HMC983LP5E/HMC984LP4E fractional-N synthesizer chip set.
[11] Measured with a 100 Ω external resistor termination, resulting in 50 Ω effective input impedance of Reference. Full FOM performance up to
maximum 3.3 Vpp input voltage.
[12] Measured with 100 Ω external termination AC coupled on HMC984LP4E & HMC983LP5E evaluation board.
[13]Measured with HMC983LP5E/HMC984LP4E chip set as fractional-N synthesizer. Crystal input frequency = 100 MHz, CP current = 2.5 mA, CP
offset current = 245 uA, Loop lter bandwidth = 87 KHz, DSM Mode B selected. Cycle Slip Prevention (CSP) is disabled in HMC984LP4E by setting
Reg 01h [4] = 0. Setting Reg 01h [4] = 1 enables CSP in the two chip PLL.
6700
6750
6800
6850
6900
6950
7000
7050
0 50 100 150 200 250 300
TIME (us)
PLL OUTPUT FREQUENCY (MHz)
Cycle Slip Disabled
CSP Enabled
Reg0Eh[18:15] = 8h
CSP Enabled
Reg0Eh[18:15] = 1h
6700
6750
6800
6850
6900
6950
7000
7050
0 50 100 150 200 250 300
TIME (us)
PLL OUTPUT FREQUENCY (GHz)
Cycle Slip Disabled
CSP Enabled
Reg0Eh[18:15] = 8h
CSP Enabled
Reg0Eh[18:15] = 1h
Figure 23. HMC984LP4E & HMC983LP5E
PLL Cycle Slip Prevention at 100 MHz PD [13]
Figure 24. HMC984LP4E & HMC983LP5E
PLL Cycle Slip Prevention at 50 MHz PD [13]
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
8
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Table 2. Pin Descriptions
Pin Number Function Description Interface Schematic
1REF_ EN Gate control output for TCXO clock export
2DTSTO Lock Detect/GPIO bit 0
3 VCOp Positive Input Pin for PFD
4VCOn Negative Input Pin for PFD
5VCCPD 5 V Analog Supply for Differential PFD
6,7 VDDPD1, VDDPD2 3 V Phase Detector Supply 1, 3 V Phase Detector Supply 2
8VDDCP 5 V Charge Pump Supply
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 9
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Table 2. Pin Descriptions
Pin Number Function Description Interface Schematic
9 CP Charge Pump Output Pin
10 VPPCP 5 V Analog Power Supply Pin Charge Pump
11 AVDD 3 V Analog Supply
12 BIAS External Decoupling for Analog Bias Circuits
13 RVDD 3 V Supply Pin for Reference Circuits
14 XREFP Reference/TCXO Input Pin
15 NC No Connect Pin
16 DVDD 3 V Digital Supply Pin
17 CEN Chip Enable Pin
18 SDO Serial Data Output Pin
Continued...
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
10
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Table 2. Pin Descriptions
Pin Number Function Description Interface Schematic
19,
20,
21
SENb,
SDI,
SCLK
Serial Port Enable Input Pin, Active Low,
Serial Port Data Input Pin,
Serial Data Clock Input Pin
22 CHIP3 Chip Address Bit 3
23 UPSAT Reference Saturation Output
24 DNSAT
VCO Saturation Output Flag
Also Multiplexed with Crystal Oscillator Clock
Continued...
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 11
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Outline Drawing
Part Number Package Body Material Lead Finish MSL Rating [2] Package Marking [1]
HMC984LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 H984
XXXX
[1] 4-Digit lot number XXXX
[2] Max peak reow temperature of 260 °C
Package Information
Table 19. Absolute Maximum Ratings
Max VDC to Paddle on Supply Pins 6,
7, 11, 13, 16 -0.3 to 3.6 V
VCCPD, VPPCP, VDDCP -0.3 to +5.5 V
VCOp, VCOn Common Mode Voltage VCCPD - 1.4 V
XREFP 50 Ω Source + 12 dBm
Digital Input Voltage Range 0.25 to DVDD + 0.5 V
Digital Load 1 kΩ Minimum
Operating Temperature Range -40 to +85 °C
Operating Temperature Range -65 to +125 °C
Maximum Junction Temperature 125 °C
Storage Temperature -65 to +125 °C
Thermal Resistance (Rth)
(junction to ground paddle) 12 °C/W ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Reow Soldering
Peak Temperature
Time at Peak Temperature
260 °C
40 s
ESD Sensitivity (HBM) Class 1 B
Stresses above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating only;
functional operation of the device at these or any other conditions
above those indicated in the operational section of this specication
is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
NOTES:
[1] PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC
SILICA AND SILICON IMPREGNATED.
[2] LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY.
[3] LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN.
[4] DIMENSIONS ARE IN INCHES [MILLIMETERS].
[5] LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
[6] PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE
0.25m MAX.
[7] PACKAGE WARP SHALL NOT EXCEED 0.05mm
[8] ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB
RF GROUND.
[9] REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND
PATTERN.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
12
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Evaluation PCB
Item Contents Part Number
Evaluation Kit
HMC984LP4E and HMC983LP5E PLL Chipset Evaluation PCB
USB Interface Board
6’ USB A Male to USB B Female Cable
CD ROM (Contains User Manual, Evaluation PCB Schematic, Evaluation Software)
EKIT01-HMC983LP5E
Table 20. Evaluation Order Information
The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohms
impedance while the package ground leads and exposed paddle should be connected directly to the ground plane
similar to that shown unless mentioned otherwise. A sufficient number of via holes should be used to connect the top
and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 13
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Evaluation PCB Block Diagram
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
14
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Typical Performance Characteristics
Theory of Operation
Primary target application of the HMC984LP4E is to be used with the HMC983LP5E as shown in Figure 25. Together
these two components form a high performance, low noise, ultra low spurious emissions fractional-N frequency
synthesizer. The two components are separated in order to maximize isolation between them, and minimize common
distortion and modulation by-products that exist in all PLLs. Careful IC design and increased isolation between the
two components result in high performance , high spectral efficiency PLL, with extremely low spurious emissions.
Figure 25. Typical Application of HMC984LP4E with HMC983LP5E to Form a Frequency Synthesizer
HMC984LP4E is a high performance low noise phase detector and charge pump. It consists of the following main
functional blocks;
1. Reference/Crystal Buffer
2. Reference Path ’R’ Divider
3. Differential Phase/Frequency Detector
4. 5 V Charge Pump
5. Two Lock Detect Circuits
6. Serial Port Interface
PLL Performance Metrics (Figure of Merit, Noise Floor, and Flicker Noise Models)
The phase noise of an ideal phase locked oscillator is dependent upon a number of factors:
a. Frequency of the VCO, and the Phase detector
b. VCO Sensitivity, kvco, and VCO and Reference Oscillator phase noise proles
c. Charge Pump current, Loop Filter and Loop Bandwidth
d. Mode of Operation: Integer, Fractional modulator style
The contributions of the PLL to the output phase noise can be characterized in terms of a Figure of Merit (FOM) for
both the PLL noise oor and the PLL icker (1/f) noise regions, as follows:
PLL PHASE
NOISE
( )
2
2
0
0
20
1
0,, p
p
p m pd
m pd
Ff
Ff
ff f ff
Φ=+ (Eq 1)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 15
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
where:
Ф p
2 Phase Noise Contribution of the PLL (rads2/Hz)
fo Frequency of the VCO (Hz)
fpd Frequency of the Phase Detector (Hz)
fm Frequency offset from the carrier (Hz)
Fpo Figure of Merit (FOM) for the phase noise oor
Fp1 Figure of Merit (FOM) for the icker noise region
Figure 26. Figure of Merit Noise Models for the PLL
If the free running phase noise of the VCO is known, it may also be represented by a gure of merit for both 1/f2 , Fv2,
and the 1/f3, Fv3, regions.
VCO PHASE
NOISE
( )
2
20
220 3
023
,m
mm
Ff
Ff
ff ff
Φ=+
ν
ν
ν
(Eq 2)
The Figures of Merit are essentially normalized noise parameters for both the PLL and VCO that can allow quick
estimates of the performance levels of the PLL at the required VCO, offset and phase detector fre quency. Normally,
the PLL IC noise dominates inside the closed loop bandwidth of the synthesizer, and the VCO dominates outside the
loop bandwidth at offsets far from the carrier. Hence a quick estimate of the closed loop performance of the PLL can
be made by setting the loop bandwidth equal to the frequency where the PLL and free running phase noise are equal.
The Figure of Merit is also useful in estimating the noise parameters to be entered into a closed loop design tool such
as Hittite PLL Design, which can give a more accurate estimate of the closed loop phase noise and PLL loop lter
component values.
Given an optimum loop design, the approximate closed loop performance is simply given by the minimum of the PLL
and VCO noise contributions.
( )
2 22
min ,
p
ν
Φ= ΦΦ (Eq 3)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
16
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
An example of the use of the FOM values to make a quick estimate of PLL performance: Estimate the phase noise of
an 7 GHz closed loop PLL with a 100 MHz reference operating in Fractional Mode B with the VCO operating at 7 GHz.
Assume an HMC505LP4E VCO has free running phase noise in the 1/f2 region at 1 MHz offset of -130 dBc/Hz and
phase noise in the 1/f3 region at 1 kHz offset of -48 dBc/Hz.
Fv1_dB = -130 Free Running VCO PN at 1 MHz offset
+20*log10(1e6) PNoise normalized to 1 Hz offset
-20*log10(7e9) PNoise normalized to 1 Hz carrier
= -206.9 dBc/Hz at 1 Hz VCO FOM
F
v3
_dB = -48 Free Running VCO PN at 1 kHz offset
+30*log10(1e3) PNoise normalized to 1 Hz offset
-20*log10(7e9) Pnoise normalized to 1 Hz carrier
= -154.9 dBc/Hz at 1 Hz VCO Flicker FOM
We can see from Figure 3 and Figure 4 respectively that the PLL FOM oor and FOM icker parameters in fractional
Mode A are approximately:
Fpo_dB = -227 dBc/Hz at 1 Hz
Fp1_dB = -267 dBc/Hz at 1 Hz
Each of the Figure of Merit equations result in straight lines on a log-frequency plot. We can see in the example below
the resulting
PLL oor at 7 GHz = Fpo_dB + 20log10(fvco) - 10log10(fpd) = -227+ 196.9 -80 = -110.1 dBc/Hz
PLL Flicker at 1 kHz = Fp1_dB + 20log10(fvco) - 10log10(fm) = -267 + 196.9-30 = -100.1 dBc/Hz
VCO at 1 MHz = Fv1_dB + 20log10(fvco) - 20log10(fm) = -206.9 +196.9-120 = -130 dBc/Hz
VCO icker at 1 kHz = Fv3_dB+20log10(fvco)-30log10(fm)= -154.9 +196.9-90 = -48 dBc/Hz
These four values help to visualize the main contributors to phase noise in the closed loop PLL. Each falls on a linear
line on the log-frequency phase noise plot shown in Figure 25.
Spurious Performance
Integer Operation
The VCO always operates at an integer multiple of the PD frequency in an integer PLL. In general, spurious signals
originating from an integer PLL can only occur at multiples of the PD frequency. These unwanted outputs are often
simply referred to as reference sidebands.
Spurs unrelated to the reference frequency must originate from outside sources. External spurious sources can
modulate the VCO indirectly through power supplies, ground, or output ports, or bypass the loop lter due to poor
isolation of the lter. It can also simply add to the output of the PLL.
The HMC984LP4E together with the HMC983LP5E have been designed and tested for ultra-low spurious performance.
Reference spuri ous levels can be typically below -100 dBc with a well designed board layout. A regulator with low
noise and high power supply rejection, such as the HMC860LP3E, is recommended to minimize external spurious
sources.
Reference spurious levels of below -100 dBc require superb board isolation of power supplies, isolation of the VCO
from the digital switching of the synthesizer and isolation of the VCO load from the PLL. Typical board layout, regulator
design, demo boards and application information are available for very low spurious operation. Operation with lower
levels of isolation in the application circuit board, from those rec ommended by Hittite, can result in higher spurious
levels.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 17
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Of course, if the application environment contains other interfering frequencies unrelated to the PD fre quency, and if
the application isolation from the board layout and regulation are insufficient, then the unwanted interfering frequencies
will mix with the desired PLL output and cause additional spurs. The level of these spurs is dependant upon isolation
and supply regulation or rejection (PSRR).
Fractional Operation
Unlike an integer PLL, spurious signals in a fractional PLL can occur due to the fact that the VCO operates at
frequencies unrelated to the PD frequency. Hence intermodulation of the VCO and the PD harmonics can cause
spurious sidebands. Spurious emissions are largest when the VCO operates very close to an integer multiple of the
PD. When the VCO operates exactly at a harmonic of the PD then, no in-close mixing products are present.
Interference is always present at multiples of the PD frequency, fpd, and the VCO frequency, fvco. If the fractional mode
of operation is used, the difference, Δ, between the VCO frequency and the nearest har monic of the reference, will
create what are referred to as integer boundary spurs. Depending upon the mode of operation of the PLL, higher
order, lower power spurs may also occur at multiples of integer fractions (sub-harmonics) of the PD frequency. That is,
fractional VCO frequencies which are near n·fpd + fpd·d/m, where n, d and m are all integers and d≤m (mathematicians
refer to d/m as a rational num ber). We will refer to fpdd/m as an integer fraction. The denominator, m, is the order of
the spurious product. Higher values of m produce smaller amplitude spurious at offsets of mΔ and usually when m> 4
spurs are small or unmeasurable.
The worst case, in fractional mode, is when d =1, and the VCO frequency is offset from n·fpd by less than the loop
bandwidth. This is the “in-band fractional boundary” case.
Figure 27. Fractional Spurious Example
Characterization of the levels and orders of these products is not unlike a mixer spur chart. Exact levels of the products
are dependent upon isolation of the various synthesizer parts. Hittite can offer guidance about expected levels of
spurious with our PLL and VCO application boards. Regulators with high power supply rejection ratios (PSRR) are
recommended, especially in noisy applications.
When operating in fractional mode, charge pump and phase detector linearity is of paramount importance. Any non-
linearity degrades phase noise and spurious performance. Phase detector linearity degrades when the phase error is
very small and is operating back and forth between reference lead and VCO lead. To mitigate these non-linearities in
fractional mode it is critical to operate the phase detector with some nite phase offset such that either the reference
or VCO always leads. To provide a nite phase error, extra current sources can be enabled which provide a constant
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
18
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
DC current path to VDD (VCO leads always) or ground (reference leads always). These current sources are called
charge pump offset and they are controlled via Reg 04h[20:14]. The time offset at the phase detector should be ~2.5
ns + 4 Tps, where Tps is the RF period at the fractional prescaler input in nanoseconds. The specic level of charge
pump offset current is determined by this time offset, the comparison frequency and the charge pump current and can
be calculated from:
Required CP Offset = (2.5 ∙ 10-9+ 4TPS) ∙ (Fcomparison) ∙ ICP where:
TPS: is the RF period at the fractional prescaler input (sec)
ICP: is the full scale current setting of the switching charge pump (A)
Fcomparison: is the comparison frequency (Hz)
(Eq 4)
Note that this calculation can be performed for the center frequency of the VCO, and does not need renement for
small differences (<25%) in center frequencies. Also, operation with unreasonably large charge pump offset may
cause Lock Detect to incorrectly indicate an unlocked condition. To correct, reduce the offset to recommended levels.
Reference/Crystal Input Buffer
The ultra-low noise phase-detector requires the best possible reference signal. The low phase noise reference input
buffer is optimized for this purpose. The input pin XREFP is DC coupled internally and there is 800 mV DC bias on
the pin. The reference source should be AC coupled to the pin. The maximum input power can be up to 12 dBm from
a 50 Ω source. In order to achieve best phase noise performance, the reference source should have a phase noise
oor of -160 dBc/Hz or better.
Reference Path ’R’ Divider
HMC984LP4E has 14-bit frequency divider that divides the incoming reference frequency by any number from 1 to
214-1 = 16,383 inclusive. The maximum frequency at which the phase detector can work depends on the mode of
operation when working as a PLL with its companion chip HMC983LP5E. In integer mode, the reference buffer and
divider can work up to 175 MHz, and in fractional mode the maximum frequency is typically 125 MHz. Hence higher
crystal frequencies need to be divided down by the R divider in order to generate phase comparison frequency that
meets the limits of the phase detector. The minimum reference frequency can be as low as 100 kHz provided that
sharp rise and fall times (less than 500 ps) are guaranteed. Internally, the reference signal is used by other circuitry,
besides the phase detector. For best performance, it is recommended to use a higher reference frequency that is
divided by the internal R-Divider to generate the required phase comparison frequency.
Table 3. Reference Sensitivity Table
Square Input Sinusoidal Input
Frequency
(MHz)
Slew > 0.5V/ns Recommended Swing (Vpp) Recommended Power Range (dBm)
Recommended Min Max Recommended Min Max
< 10 YES 0.6 2.5 x x x
10 YES 0.6 2.5 x x x
25 YES 0.6 2.5 ok 8 15
50 YES 0.6 2.5 YES 6 15
100 YES 0.6 2.5 YES 5 15
150 ok 0.9 2.5 YES 4 12
200 ok 1.2 2.5 YES 3 8
200 to 350 x x x YES15 10
Note: For greater than 200 MHz operation, use buffer in High Frequency Mode. Reg 08h[11] = 1
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 19
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Differential Phase-Frequency Detector
As shown in Figure 25, the HMC984LP4E features an ultra-low noise digital differential Phase Detector (PD) with
two differential inputs. One input comes from the reference path divider and the other from VCO path divider. The
reference input is internal to HMC984LP4E whereas the divided VCO input is external. The output from the PD is fed
to the charge pump in HMC984LP4E which converts the PD digital output to a current with programmable gain. The
output of the CP is directly proportional to the phase difference between the divided reference and the VCO path
signals.
Figure 28. HMC984LP4E Input Interface
The input of PD is a differential current-input. The input interface congurations are shown in Figure 25 and Figure
25. The HMC984LP4E is designed to work with its companion divider part, the HMC983LP5E, that provides an open
collector output. The inputs are internally pulled up to VCCPD with on-chip 50 Ω resistors. Thus, any open collector
buffer can drive the PD inputs. A minimum of 750 mVpp single-ended level is needed to drive the PD inputs.
Figure 29. HMC984LP4E Input Interface with Companion Part HMC983LP5E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
20
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
The PD has several features and controls including:
• Phase Swap
• UP/DN Enable
• Forced Outputs
Phase swap
The input phase signals to the PD can be swapped internally by writing Reg 03h[4] = 1. When swapped, the PD gain
will be reversed. This feature enables the HMC984LP4E to be interfaced with reverse polarity VCOs (VCOs that have
negative gain curve), as well as systems that use an active loop lter where the operational amplier introduces a
reverse phase polarity.
Forced Outputs
The UP or DN outputs from the PD can be forced with SPI control to keep constantly active in order to achieve faster
lock (to force UP write Reg 04h[26] = 1, to force DN write Reg 04h[27] = 1). This capability is used in CSP (Cycle
Slip Prevention) feature when large phase errors are detected. In such a case the CP is continuously turned on the
appropriate direction (UP or DN) by the internal state machine to force faster phase convergence, and thus achieve
faster lock. Forced otput capability is also useful for testing purposes. It can be used to bring the VCO tune control
voltage to supply or ground, and observe the limits of the VCO.
Cycle Slip Prevention
When the frequency of the synthesizer is changed and the current VCO frequency is far from the desired locked
frequency, the phase difference at the PD varies rapidly over a range larger than ±2π radians. Since the gain of the
PD varies linearly with phase only up to ±2π, the gain of conventional PDs will cycle from high gain, when the phase
difference approaches a multiple of 2π, to low gain, when the phase difference is slightly more than 2π radians. This
phenomena is known as cycle slipping. Cycle slipping causes the pull-in rate during the phase acquisition to vary
cyclically as shown in the red curve in Figure 25. Cycle slipping can dramatically increase the time to lock to a value
far greater than that predicted by normal small signal Laplace analysis.
Figure 30. Cycle Slipping
The HMC984LP4E PD features Cycle Slip Prevention (CSP) only when working in conjunction with the companion
part, the HMC983LP5E. When enabled, the CSP feature holds the PD gain in the appropriate polarity until such time
as the frequency difference is near zero. This enables signicantly faster lock times as shown in Figure 25. The use of
CSP feature is enabled with CSP Enable (Reg 01h[4] = 1) and CSP Output Enable (Reg 01h[13] = 1). The CSP feature
may be optimized for a given set of PLL dynamics by adjusting the PD sensitivity to cycle slipping. This is achieved by
adjusting CSP Reset Delay (Reg 03h[2:0]).
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 21
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
The HMC984LP4E has two outputs, UPSAT and DNSAT, which indicate to the HMC983LP5E whether the Reference
or the VCO is leading in phase. These outputs are CMOS signal with DVDD levels. When HMC983LP5E detects
saturation (large phase error), it congures itself, and the HMC984LP4E in order to eliminate or reduce cycle clipping.
There are additional controls for adjusting the CSP operation in HMC983LP5E. The controls for CSP feature are;
1. Register 0Eh bits [18:15] control the step size, where step is a VCO cycle.
2. Register 0Eh bit [29] increases the step size by a factor of 16 for operations with low reference frequencies.
The actual operation of CSP will depend on the Reference and VCO frequencies and will need to be tailored for each
application.
Charge Pump
The charge pump in HMC984LP4E converts the phase detector digital outputs to appropriate current level that is
proportional to phase difference between the reference and the VCO. A simplied block diagram of the charge pump
is shown in Figure 25. The HMC984LP4E CP has programmable current gain and offset current.
Charge Pump Gain Current
CP gain current denes the gain of Phase Detector vs. Phase Difference in Amps/radians. The UP and DOWN
gain currents are congured in Reg 04h[6:0] and Reg 04h[13:7] respectively. Both UP and DOWN currents can be
programmed to provide up to 2.5 mA independently in 127 steps (20 μA/step). Resulting phase detector gain is the
total current from one side divided by 2π. For example, if both UP and DOWN currents are set 2 mA each, the gain
would be 2 mA/2π = 318.31 μA/radian. Typically both of the gain currents are set to the same value.
Charge Pump Phase Offset
Either of the UP or DOWN charge pumps may have a DC offset current added to it. Offset current allows the phase
detector to operate with a phase offset between the reference and the divided VCO inputs. The phase offset is
proportional to the ratio of the offset current to the main current times the period of the phase comparison clock.
Offset Current 1
PD Phase offset= CP Current PD
f
×(Eq 5)
It is recommended to operate the HMC984LP4E with a phase offset when using fractional mode to reduce non-linear
effects from any UP and DN pump mismatches that may exist. Phase noise in fractional mode is strongly affected by
charge pump offset.
The magnitude of offset current is set in Reg 04h[20:14], and can be added to the UP (Reg 04h[21] = 1) or DOWN (Reg
04h[22] = 1) pumps.
As an example, if the main pump gain was set at 2 mA, an offset of 160 µA (Reg 04h[20:14] = 20h) and 50 MHz PFD
rate would represent a phase offset of about (160/2000)*360 = 28.8 degrees or (163.5 μA/2000 μA)*20 ns = 1.6 ns
phase offset at the PD input.
Charge Pump High Gain (HiK) Mode
Operating the CP of the HMC984LP4E in High Gain mode (Reg 04h[23] = 1) can improve PLL phase noise performance
by up to 3 dB. In High Gain mode the charge pump can deliver current of 3.5 mA + normal programmed CP current.
High gain mode can be used without the normal charge pump current in which case the loop lter should be designed
with a current of 3.5 mA. In the case where high gain mode is used with the normal CP current, the loop lter should be
designed with a charge pump current of 3.5 mA + programmed CP current. The high gain mode current is depended
on the loop lter voltage, therefore the high gain mode should be used with active loop lters to keep a constant
voltage a the charge pump output.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
22
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Figure 31. Charge Pump Block Diagram
PFD Jitter and Lock Detect Background
In normal phase locked operation the divided VCO signal arrives at the phase detector in phase with the divided
crystal signal, known as the reference signal. Despite the fact that the device is in lock, the phase of the VCO signal
and the reference signal vary in time due to the phase noise of the crystal and VCO oscillators, the loop bandwidth
used and the presence of fractional modulation or not. The total integrated noise on the VCO path normally dominates
the variations in the two arrival times at the phase detector if fractional modulation is turned off.
To determine weather the VCO is in lock or not, it is necessary to distinguish between normal phase jitter when in lock
and phase jitter when not in lock.
First, the meaning of jitter of the synthesizer that is observed at the phase detector in integer or fractional modes
needs to be understood.
The standard deviation of the arrival time of the VCO signal, or the jitter, in integer mode may be estimated with a
simple approximation if it is assumed that the locked VCO has a constant phase noise, Ф2 (ƒ0), at offsets less than
the loop 3 dB bandwidth and a 20 dB per decade roll off at greater offsets. The simple locked VCO phase noise
approximation is shown on the left of Figure 25.
Figure 32. Synthesizer Phase Noise & Jitter
With this simplication the single sideband integrated VCO phase noise, Ф2 , in rads2 at the phase detector is given by
22 2
() /
2
SSB o BfN

Φ=Φ


π
(Eq 6)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 23
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
where
Ф2
SSB(ƒ0) is the single sideband phase noise in rads2/Hz inside the loop bandwidth, B is the 3 dB corner frequency of
the closed loop PLL and N is the division ratio of the prescaler.
The rms phase jitter of the VCO in rads, Ф , results from the power sum of the two sidebands:
Φ= Φ
2
2SSB (Eq 7)
Since the simple integral of (EQ 6) is just a product of constants, the integral in the log domain can easily be done .
For example if the VCO phase noise inside the loop is -100 dBc/Hz at 10 kHz offset and the loop bandwidth is 100
kHz, and the division ratio N=100, then the integrated single sideband phase noise at the phase detector in dB is given
by Ф2 dB = 10log (Ф2(ƒ0)Bπ ⁄ N2) = -100 + 50 + 5 - 40 = -85 dBrads, or equivalently Ф = 10-85/20 = 56 urads rms or 3.2
milli-degrees rms.
While the phase noise reduces by a factor of 20Log10(N) after division to the reference, the jitter is a constant.
The rms jitter from the phase noise is then given by Tjnp = Tref Ф / 2π
In this example if the reference was 50 MHz, Tref = 20 nsec, and hence Tjpn = 178 femto-sec.
A normal 3 sigma peak-to-peak variation in the arrival time therefore would be
±3·√2·Tjpn = 0.756 ps
If the synthesizer was in fractional mode, the fractional modulation of the VCO divider will dominate the jitter. The exact
standard deviation of the divided VCO signal will vary based upon the modulator chosen, however a typical modulator
will vary by about ±3 VCO periods, ±4 VCO periods, worst case.
If, for example, a nominal VCO at 5 GHz is divided by 100 to equal the reference at 50 MHz, then the worst case
division ratios will vary by 100±4. Hence the peak variation in the arrival times caused by DS modulation of the
fractional synthesizer at the reference will be
∆Σ =±−* max min( )/2j pk vcoT TN N (Eq 8)
In this example, TjDSpk = ±200 ps (104-96)/2 = ±800 psec. If it is assumed that the distribution of the delta sigma
modulation is approximately Gaussian, TjDSpk could be approximated as a 3 sigma jitter, and hence the rms jitter of the
DS modulator could be estimated as ~ 1/3 of TjDSpk or ~ 267 psec in this example.
Hence the total rms jitter Tj, expected from the delta sigma modulation plus the phase noise of the VCO would be
given by the rms sum , where
∆Σ
= +
22
()
3
j pk
j jpn T
TT (Eq 9)
It is apparent that the jitter from (EQ. 9) at the phase detector is dominated by the fractional modulation. In general,
~t ±0.8 nsec of normal variation in the phase detector arrival times has to be expected when in fractional mode. In
addition, lower VCO frequencies with high reference frequencies will have much larger variations. For example, a 1
GHz VCO operating at near the minimum nominal divider ratio of 36, would, according to (EQ 8), exhibit about ±4
nsec of peak variation at the phase detector, under normal operation. The lock detect circuit must not confuse this
modulation as being out of lock.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
24
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
HMC984LP4E Lock Detect Circuits
HMC984LP4E includes two lock detect circuits.
• Legacy Lock Detect Function
• Phase Measurement Based Lock Detect Function
Reg 01h[6:8] enables the lock detect functions of the HMC984LP4E. The LD output is available either from the GPO
pin D0 or through SPI register Reg 12h.
Legacy Lock Detect Function
The Lock Detect circuit in the HMC984LP4E places a one shot window around the reference. The one shot window
may be generated by either an analog one shot circuit or a digital one shot based upon an internal ring oscillator timer.
Clearing LKDOS One Shot Select (Reg 07h[22]=0) will result in a nominal ±10 nsec ‘analog’ window of xed length,
as shown in Figure 9. Setting this bit to 1 will result in a variable length ’digital’ widow. The digital one shot window
is controlled by LKDOS Ring Oscillator Speed (Reg 07h[20:19]). The resulting lock detect window period is then
generated by the number of ring oscillator periods dened in LKDOS One Shot Pulse Width (Reg 07h[18:16]). The lock
detect ring oscillator may be observed on the GPO port by setting Reg 07h[21] =1 and conguring the Reg 08h[7:0] =
C1h in (GPO). Lock detect does not function when this test mode is enabled.
LKDOS OK Count (Reg 07h[15:0]) denes the number of consecutive counts of the VCO that must land inside the lock
detect window to declare lock. If for example LKDOS OK Count = 1000 , then the VCO arrival would have to occur
inside the selected lock window 1000 times in a row to be declared locked. When locked the Lock Detect ag (Reg
12h[2]=1 ) is set, Reg 12h is a read only register. A single occurrence outside of the window will result in clearing the
Lock Detect ag.
Figure 33. Normal Lock Detect Window - Integer Mode, Zero Offset
Lock Detect with Phase Offset
When operating in fractional mode the linearity of the phase detector and charge pump is more critical than in integer
mode. The phase detector linearity deteriorates when operating with zero phase offset. Hence in fractional mode it is
necessary to offset the phase of the reference and the VCO at the phase detector. In such a case, for example with an
offset delay, the mean phase of the VCO will always occur after the reference, as shown in Figure 10. The lock detect
circuit window can be made more selective with a xed offset delay by setting Reg 05h [0]=1 and Reg 05h[1]=1. The
offset can be assigned in advance of the reference by setting Reg 05h[1]=0 and Reg 05h [0]=1.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 25
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Figure 34. Lock Detect Window - Fractional Mode with Offset
Lock Detect with Phase Measurement
Lock Detect with Phase Measurement is based on phase error measurement at the PFD output. The phase error
measurement is done in terms of the reference period at the PFD input. The period of the reference is rst measured
with a delay line and this count is available in read-only register Reg 10h. The phase error at the output of the PFD
is then measured with the same delay line and this count is available in the read-only register Reg 11h. When the
PLL is not locked, the measured phase error count will vary every time the Reg 11h is read and will become a stable
value once PLL is locked. The phase error count will then be proportional to the static phase error at the PFD output.
For example, assuming that PLL is locked, if the reference duration count is 150 in Reg 10h and Re g 11h reads 35
then the approximate static phase error at the PFD output is 20*(35/150) = 4.7 ns assuming a 20 ns reference period
or Fpfd of 50 MHz. Reg 06h [13:0] denes the low and high thresholds for current phase error count. Reg 06h[23:14]
denes the number of reference cycles that the phase error has to be within the thresholds before the lock is declared.
For example, if the low threshold is set to Reg 06h [6:0] = 20d and high threshold is set to Reg 06h [13:7] = 50d and
the LD OK Count is set to Reg 06h[23:14] = 512d, then the phase error count has to be between 20 and 50 for 512
consecutive reference cycles before that lock is declared. The thresholds make it easier to dene lock condition in
case of fractional operation where the static phase error is expected to be larger due to charge pump offset currents.
Chip Address Pins
HMC984LP4E has three programmable chip address bits, which enable the HMC984LP4E to be used in an SPI bus
conguration. Two LSB chip address bits are internal and bond wire programmable at the time of packaging. The MSB
bit is available externally as pin CHIP3. The chip address pins are read at power-up and every time the chip is reset.
By default, all CHIP3 is internally pulled to DVDD thus there is no need to connect the pin to DVDD if the address bit
is to be set as logic high. To assign a 0 to address bit, pin should be connected to ground. The internal CHIP1 and
CHIP2 bits are internally tied to ground.
The chip address for the companion chip HMC983LP5E is stored in Reg 09h[2:0] of HMC984LP4E. In cases when an
SPI command is common to both devices, it is not necessary to send separate commands to each part. Both parts
are always listening to the SPI bus and when a common command is issued, they will take the command and update
the corresponding registers. Writing its own chip address to the companion chip address register Reg 09h[2:0] will
disable this feature.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
26
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
General Purpose Input Output Pin D0
HMC984LP4E has one GPIO pin D0. This pin normally functions as the output for the lock detect. It can be programmed
to test and probe several internal signals. Following signals are available (Reg 08h[3:0]).
1. gpo_test_out.
2. Lock Detect or Lock Indicator output
3. PFD UP output going to Lock Detect
4. PFD DN output going to Lock Detect
5. R-Divider output to digital
6. R-Divider output
7. Saturation reset Signal
8. PFD saturation DN (VCO) output
9. PFD saturation UP (REF) output
10. Ring oscillator test output
11. One-shot pulse output
12. One-shot trigger output
13. Pull UP hard
14. Pull down hard
15. VCO divider output to digital
16. Crystal oscillator buffer output
See the serial port section for programming conguration, Reg 08h.
Serial Port Interface
The HMC984LP4E features a four wire serial port for simple communication with the host controller. Typical serial port
operation can be run with SCK at speeds up to 30 MHz.
The details of SPI access for the HMC984LP4E are provided in the following sections. Note that the READ operation
below is always preceded by a WRITE operation to Register 0 to dene the register to be queried. Also note that
every READ cycle is also a WRITE cycle in that data sent to the SPI while reading the data will also be stored by the
HMC984LP4E when SEN goes high. If this is not desired then it is suggested to write to Reg 00h during the READ
operation so that the status of the device will be unaffected.
Power on Reset and Soft Reset
The HMC984LP4E has a built in Power On Reset (POR) and a serial port accessible Soft Reset (SR). POR is
accomplished when power is cycled for the HMC984LP4E while SR is accomplished via the SPI by writing Reg 00h
= 80h, followed by writing Reg 00h = 00h. All chip registers will be reset to default states approximately 250 us after
power up.
Serial Port WRITE Operation
The host changes the data on the falling edge of SCK and the HMC984LP4E reads the data on the rising edge.
A typical WRITE cycle is shown in Figure 1. It is 40 clock cycles long.
1. The host both asserts SEN (active low Serial Port Enable) and places the MSB of the data on SDI followed
by a rising edge on SCK.
2. HMC984LP4E reads data on SDI (the MSB) on the 1st rising edge of SCK after SEN.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 27
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
3. HMC984LP4E registers the data bits, D29:D0, in the next 29 rising edges of SCK (total of 30 data bits).
4. Host places the 7 register address bits, A6:A0, on the next 7 falling edges of SCK (MSB to LSB) while the
HMC984LP4E reads the address bits on the corresponding rising edge of SCK.
5. Host places the 3 chip address bits, CA2:CA0=[110], on the next 3 falling edges of SCK (MSB to LSB). Note
the HMC984LP4E chip address is xed as “4d” or “100b”.
6. SEN goes from low to high after the 40th rising edge of SCK. This completes the WRITE cycle.
7. HMC984LP4E also exports data back on the SDO line. For details see the section on READ operation.
Serial Port READ Operation
The SPI can read from the internal registers in the chip. The data is available on SDO pin. This pin itself is tri-stated
when the device is not being addressed. However, when the device is active and has been addressed by the SPI
master, the HMC984LP4E controls the SDO pin and exports data on this pin during the next SPI cycle.
HMC984LP4E changes the data to the host on the rising edge of SCK and the host reads the data from HMC984LP4E
on the falling edge.
A typical READ cycle is shown in Figure 1. Read cycle is 40 clock cycles long. To specically read a register, the
address of that register must be written to dedicated Reg 00h. This requires two full cycles, one to write the
required address, and a 2nd to retrieve the data. A read cycle can then be initiated as follows;
1. The host asserts SEN (active low Serial Port Enable) followed by a rising edge SCK.
2. HMC984LP4E reads SDI (the MSB) on the 1st rising edge of SCK after SEN.
3. HMC984LP4E registers the data bits in the next 29 rising edges of SCK (total of 30 data bits). The LSBs of
the data bits represent the address of the register that is intended to be read.
4. Host places the 7 register address bits on the next 7 falling edges of SCK (MSB to LSB) while the HMC984LP4E
reads the address bits on the corresponding rising edge of SCK. For a read operation this is “0000000”.
5. Host places the 3 chip address bits [100] on the next 3 falling edges of SCK (MSB to LSB). Note the
HMC984LP4E chip address is xed as “4d” or “100b”.
6. SEN goes from low to high after the 40th rising edge of SCK. This completes the rst portion of the READ
cycle.
7. The host asserts SEN (active low Serial Port Enable) followed by a rising edge SCK.
8. HMC984LP4E places the 30 data bits, 7 address bits, and 3 chip id bits, on the SDO, on each rising edge of
the SCK, commencing with the rst rising edge beginning with MSB.
9. The host de-asserts SEN (i.e. sets SEN high) after reading the 40 bits from the SDO output. The 40 bits
consists of 30 data bits, 7 address bits, and the 3 chip id bits. This completes the read cycle.
Note that the data sent to the SPI by the host during this portion of the READ operation is stored in the SPI
when SEN is de-asserted. This can potentially change the state of the HMC984LP4E. If this is undesired it
is recommended that during the second phase of the READ operation that Reg 00h is addressed with either
the same address or the address of another register to be read during the next cycle.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
28
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Figure 35. SPI Timing Diagram
DVDD = 5 V ±10%, GND = 0 V
Table 4. Main SPI Timing Characteristics
Parameter Conditions Min Typ Max Units
t1SDI to SCK Setup Time 8 nsec
t2SDI to SCK Hold Time 8 nsec
t3SCK High Duration [1] 10 nsec
t4SCK Low Duration 10 nsec
t5SEN Low Duration 20 nsec
t6SEN High Duration 20 nsec
t7SCK to SEN [2] 8nsec
t8SCK to SDO out [3] 8nsec
[1] The SPI is relatively insensitive to the duty cycle of SCK.
[2] SEN must rise after the 32nd falling edge of SCK but before the next rising SCK edge. If SCK is shared amongst several devices this timing
must be respected.
[3] Typical load to SDO is 10 pF, maximum 20 pF
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 29
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Register Map
Table 5. Reg 00h Chip ID, Soft Reset, Read Register
BIT TYPE NAME W DEFLT DESCRIPTION
[6:0] R/W Read Address Register 7 0 Address of the register to be read in the next cycle.
[7] R/W Soft Reset 1 0
Soft Reset. Writing 1 generates soft reset. Resets all the digital
and registers to default states. Writing 0 resumes normal chip
operation.
[31:8] R/W Chid ID 24 97331h Part Number, Description. Read reg00h returns chip ID.
Table 6. Reg 01h Enable Register
BIT TYPE NAME W DEFLT DESCRIPTION
[0] R/W Use SPI Chip Enable 1 0
0 = Use CEN pin for chip enable.
1 = Ignore CEN pin and use SPI chip_en bit.
[1] R/W SPI CE 1 1 Chip enable from SPI = 1 allows chip control through SPI software.
[2] R/W R Divider Enable 1 1 Enable Reference Divider enabled
[3] R/W PFD Enable 1 1
1 = PFD enabled
0 = PFD disabled
[4] R/W CSP Enable 1 1 Enable cycle-slip prevention.
[5] R/W Charge Pump Enable 1 1 Enable Charge Pump.
[6] R/W Lock Detect Enable 1 1 Main Lock Detect enable
[7] R/W Lock Detect Watch Dog Enable 1 1 Lock Detected Watch Dog. Declares unlock if no UP/DN pulses are
received from PFD.
[8] R/W One Shot Lock Detect Enable 1 1 Legacy Lock Detect enable.
[9] R/W GPO Enable 1 1
1 = GPIO output enable, D0 pin is output.
0 = D0 pin congured as input.
[10] R/W Reference Buffer Enable 1 1 Enable Reference Buffer.
[11] R/W Test Clocks Enable 1 1 Enable test clocks to digital (Xtal, Rdiv, Vdiv).
[12] R/W Bias Enable 1 1 Enables the bias currents to the analog blocks.
[13] R/W CSP Output Enable 1 1 Enables the output pad for
[14] R/W CP OP-AMP Enable 1 1 Enables the charge pump operational amplier.
[17:15] R/W Unused bits 3111b
[18] R/W VCO Input Test Clock Enable 1 0 Enable for VCO/Divider input test clock.
[19] R/W Unused bit 4 0
Table 7. Reg 02h REFDIV Reference Divider Register
BIT TYPE NAME W DEFLT DESCRIPTION
[13:0] R/W R-Divider Ratio 14 1Reference Divider Division Ratio R. Minimum = 1, Maximum =
16383d.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
30
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Table 8. Reg 03h PFD Settings Register
BIT TYPE NAME W DEFLT DESCRIPTION
[2:0] R/W CSP Reset Delay 3100b The number of reference clock cycles after which the saturation
detection is reset.
[3] R/W CSP Auto Disable 1 1 When 1, PD saturation is disabled when Lock Detect becomes 1.
[4] R/W PD Phase Swap 1 0 Swap PD inputs when 1.
[5] R/W PD Short Mode Enable 1 0
1 = Apply reference to both PFD inputs when pfd_swap_phase
Reg08h[4]= 0 or applies Divider output to both PFD inputs when
pfd_swap_phase Reg08h[4] = 1.
[6] R/W PD Up Enable 1 1 1 = Enable UP output from PD.
0 = Disable UP output from PD.
[7] R/W PD Down Enable 1 1 1 = Enable DN output from PD.
0 = Disable DN output from PD.
[8] R/W PD Force Up 1 0 1 = Forces UP output from the PD to stay continuously on.
0 = Normal UP operation.
[9] R/W PD Force Down 1 0 1 = Forces DN output from the PD to stay continuously on.
0 = Normal DN operation.
[10] R/W PD Outputs to LD Enable 1 1 1 Enables PD outputs to Lock Detect in the Digital.
[11] R/W Reset PD when Xtal Gate 1 1 1 resets the PD when crystal is exported to the companion
Prescaler/Sigma Delta chip HMC983LP5E
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 31
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Table 9. Reg 04h Charge Pump Settings Register
BIT TYPE NAME W DEFLT DESCRIPTION
[6:0] R/W Up Current 70x7h
Charge Pump DOWN MAIN current, 20 μA step, 127 steps
0000000 = Tristate if PFD also disabled.
0000001 = 20 μA
0000010 = 40 μA
...
1111111 = 2.54 m A
[13:7] R/W Down Current 70x7h
Charge Pump UP MAIN current, 20 μA step, 127 steps
000 = Tristate if PFD also disabled.
0000001 = 20 μA
0000010 = 40 μA
...
1111111 = 2.54 m A
[20:14] R/W Offset Current 70x7h
Charge Pump offset current magnitude, 5 μA step, 127 steps
0000000 = Tristate if PFD also disabled.
0000001 = 5 μA
0000010 = 10 μA
...
1111111 = 635 μA
[21] R/W Up Offset Current Enable 1 0 Enable for Charge pump offset current in up direction. Reference
signal is lagging when phase swap is 0.
[22] R/W Down Offset Current Enable 1 0 Enable for Charge pump offset current in down direction, VCO/
Divider is lagging when phase swap is 0.
[23] R/W High Gain Mode Enable 1 0 Enables high gain mode for the charge pump with uncontrolled 1
mA - 3.5 mA of additional charge pump current.
[25:24] R/W OP-Amp Bias 211b
Charge Pump Op-Amp bias select.
00 = 540 μA
01 = 689 μA
10 = 943 μA
11 = 1503 μA
[26] R/W CP Force Up Enable 1 0 Force Up current from the charge pump output.
[27] R/W CP Force Down Enable 1 0 Force Down current from the charge pump output.
[28] R/W CP Force Mid Rail Enable 1 0
Force the charge pump output to mid rail voltage. cp_force_up
(Reg09h[26]) or cp_force_dn (Reg09h[27]) have precedence over
this bit.
[29] R/W Ring Oscillator Output to CP Enable 1 0 Exports ring oscillator to pulluphard/pulldnhard for test purpose.
Table 10. Reg 05h LKD_FLXCPGAIN (Lock Detect) Register
BIT TYPE NAME W DEFLT DESCRIPTION
[0] R/W LD Asymmetric Window Enable 1 0 Enable asymmetric window for Lock Detect.
[1] R/W LD Asymmetric Direction Select 1 0 0 = Reference is expected rst.
1 = VCO/Divider is expected rst.
[2] R/W Reference Edge for LD Select 1 0 0 = Use falling edge.
1 = Use rising edge.
[4:3] R/W Flex CP Mode Select 2 00b
Forces UP or DN if phase error exceeds the register value.
00 = Disabled
01 = Force when phase error > 1 ns.
10 = Force when phase error > 3 ns.
11 = Force when phase error > 5 ns.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
32
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
Table 11. Reg 06h LKDOS (Lock Detect) Register
BIT TYPE NAME W DEFLT DESCRIPTION
[6:0] R/W LD High Threshold Duration 77Fh High threshold for measuring PFD pulse width.
[13:7] R/W LD Low Threshold Duration 70x00 Low threshold for measuring PFD pulse width.
[23:14] R/W LD OK Count Threshold 10 200h Number of consecutive counts within the time window to declare
lock. “Theory of Operation” on page 14
Table 12. Reg 07h LKDOS (Legacy Lock Detect) Register
BIT TYPE NAME W DEFLT DESCRIPTION
[15:0] R/W LKDOS OK Count 16
0x1000
4096d
Number of consecutive counts within the time window to declare
lock. “Legacy Lock Detect Function” on page 24
[18:16] R/W LKD One Shot Pulse Width 3 100b
[20:19] R/W LKDOS Ring Oscillator Speed 2 00b
Set ring oscillator speed or frequency.
00 = fastest.
11 = slowest.
[21] R/W LKDOS Ring Oscillator Mode 1 0 1 = Force ring oscillator for test.
0 = Normal operation.
[22] R/W LKDOS One Shot Select 1 1 1 = Select digital one-shot.
0 = Select analog one-shot.
Table 13. Reg 08h GPIO Register
BIT TYPE NAME W DEFLT DESCRIPTION
[3:0] R/W GPO Output Signal Select 40000b
Select signal to be probed on the GPIO output pin.
0000 = gpo_test.
0001 = Locked.
0010 = PFD UP output to LKD.
0011 = PFD dn output to LKD.
0100 = R-Divider output to digital.
0101 = R-Divider output.
0110 = PFD saturation reset.
0111 = PFD saturation DN (VCO) output.
1000 = PFD saturation UP (REF) output.
1001 = Ring oscillator test output.
1010 = One-shot pulse output.
1011 = One-shot trigger output.
1100 = Pull up hard.
1101 = Pull down hard.
1110 = VCO divider output to digital.
1111 = Crystal oscillator buffer output.
[5:4] R/W GPO Static Test Value 2 00b Static test values for GPIO.
[7:6] R/W GPO Output Enable 211b
Only LSB is used.
1 = Enable GPIO output.
0 = Congure GPIO as input.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
6 - 33
FREQUENCY DIVIDERS & DETECTORS - SMT
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
Table 14. Reg 09h REFDIVSET (Reference Divider Settings) Register
BIT TYPE NAME W DEFLT DESCRIPTION
[2:0] R/W HMC983LP5E Chip Address 3001
Chip address of the Prescaler/Divider HMC983LP5E. When a
new REFDIV value is selected through the SPI, either of the two
chips will take the same command. This makes it unnecessary to
issue two separate WRITE cycles to change the REFDIV value. To
disable this feature, write the chip address of the HMC984LP4E
itself so that it will not listen to the command issued to the other
chip. See “Chip Address Pins” on page 25 for more information.
[3] R/W Force R-Divider to Bypass 1 0 1 = Force REFDIV bypass when RDIV is not equal to 1.
Table 15. Reg 0Ah Spare Register
BIT TYPE NAME W DEFLT DESCRIPTION
[9:0] R/W Not used 10 3FFh
[10] R/W XtalDisSat 1 0 Disables saturation protection on reference (Xtal) buffer.
[11] R/W XtalHighFreq 1 0 Extends bandwidth of the reference buffer.
Table 16. Reg 10h MEAS_REF Read Only Register
BIT TYPE NAME W DEFLT DESCRIPTION
[19:0] R Measured Reference Duration 20 0Measured duration of the reference period for Lock Detect
calibration.
[20] R Reference Measure Overow Flag 1 0 REF measurement overow ag.
Table 17. Reg 11h MEAS_PFD Read Only Register
BIT TYPE NAME W DEFLT DESCRIPTION
[19:0] R Measured Phase Error 20 0Measured duration of the PFD. Sign is available in Reg 12h, bit 0.
[20] R Phase Error Overow Flag 1 0 PFD pulse measurement overow ag.
Table 18. Reg 12h STATUS Read Only Register
BIT TYPE NAME W DEFLT DESCRIPTION
[0] RPhase Error Sign 1 0 Sign of PFD duration
[1] R
LD Output from Phase Error
Measurement 1 0 Lock Detect result from pulse duration based Lock Detect circuit.
[2] RLD Output from Legacy Lock Detect 1 0 Lock Detect result from legacy one-shot Lock Detect circuit.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
34
HMC984LP4E
v02.0112
DIGITAL PHASE-FREQUENCY DETECTOR
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com
Application Support: apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
NOTES:
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D