WS57C191C/291C HIGH SPEED 2K x 8 CMOS PROM/RPROM KEY FEATURES * Ultra-Fast Access Time * Pin Compatible with Am27S191/291 and N82S191 Bipolar PROMs -- t ACC = 25 ns -- t CS = 12 ns * Immune to Latch-UP * Low Power Consumption * Fast Programming * Available in 300 Mil DIP and PLDCC -- Up to 200 mA * ESD Protection Exceeds 2000V GENERAL DESCRIPTION The WS57C191C/291C is an extremely High Performance 16K UV Erasable Electrically Re-Programmable Read Only Memory (RPROM). It is manufactured in an advanced CMOS technology which enables it to operate at Bipolar PROM speeds while consuming only 25% of the power required by its Bipolar counterparts. The WS57C191C/291C is also configured in the standard Bipolar PROM pinout which provides an easy upgrade path for systems which are currently using Bipolar PROMs. The WS57C191C is packaged in a conventional 600 mil DIP package as well as a Plastic Leaded Chip Carrier (PLDCC) and a Ceramic Leadless Chip Carrier (CLLCC). The WS57C291C is packaged in a space saving 300 mil DIP package configuration. Both are available in commercial, industrial, and military operating temperature ranges. BLOCK DIAGRAM PIN CONFIGURATION TOP VIEW 6 A5 - A10 ROW ADDRESSES ROW DECODER EPROM ARRAY Chip Carrier CERDIP/Plastic DIP 16,384 BITS NC A5 A 6 A 7 5 A0 - A4 COLUMN ADDRESSES COLUMN DECODER A4 A3 A2 A1 A0 NC O0 SENSE AMPLIFIERS CS1/ VPP VCC A8 A9 4 3 2 28 27 26 1 5 25 6 24 7 23 8 22 9 21 10 20 11 19 12 13 14 15 16 17 18 CS2 O1 O2 CS3 NC O3 O4 O5 A7 A6 A5 A10 A4 CS1/VPP A3 CS2 A2 CS3 A1 NC A0 O7 O0 O6 O1 O2 GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC A8 A9 A10 CS1/VPP CS2 CS3 O7 O6 O5 O4 O3 GND 8 OUTPUTS PRODUCT SELECTION GUIDE PARAMETER 191C/291C-25 191C/291C-35 191C/291C-45 191C/291C-55 Address Access Time (Max) 25 ns 35 ns 45 ns 55 ns CS to Output Valid Time (Max) 12 ns 20 ns 20 ns 20 ns Return to Main Menu 2-7 WS57C191C/291C ABSOLUTE MAXIMUM RATINGS* MODE SELECTION Storage Temperature............................-65 to + 150C Voltage on any Pin with Respect to Ground ....................................-0.6V to +7V VPP with Respect to Ground...................-0.6V to + 14V ESD Protection ..................................................> 2000V PINS MODE CS1/ CS2 CS3 VCC OUTPUTS VPP Read VIL VIH VIH VCC DOUT X X VCC High Z X VIL X VCC High Z Output Disable VIH *NOTICE: Output Disable Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability. Program VPP X X VCC DIN Program Verify VIL VIH VIH VCC DOUT Output Disable X X VIL VCC High Z MIN MAX UNITS OPERATING RANGE RANGE TEMPERATURE VCC 0C to +70C +5V 10% Industrial -40C to +85C +5V 10% Military -55C to +125C +5V 10% Commercial DC READ CHARACTERISTICS Over Operating Range. (See Above) SYMBOL TEST CONDITIONS VIL Input Low Voltage (Note 3) -0.1 0.8 V VIH Input High Voltage (Note 3) 2.0 VCC + 0.3 V VOL Output Low Voltage IOL = 16 mA 0.4 V VOH Output High Voltage IOH = -4 mA ICC1 VCC Active Current (CMOS) VCC = 5.5V, f = 0 MHz (Note 1), Output Not Loaded Add 2mA/MHz for AC Operation VCC Active Current (TTL) VCC = 5.5V, f = 0 MHz (Note 2), Output Not Loaded Add 2mA/MHz for AC Operation ICC2 2.4 V Comm'l 30 mA Industrial 35 mA Military 35 mA Comm'l 40 mA Industrial 50 mA Military 50 mA ILI Input Leakage Current VIN = 5.5V or Gnd -10 10 A ILO Output Leakage Current VOUT = 5.5 V or Gnd -10 10 A NOTES: 2-8 PARAMETER 1. CMOS inputs: GND 0.3V or VCC 0.3V. 2. TTL inputs: VIL 0.8V, VIH 2.0V. 3. These are absolute voltages with respect to device ground pin and include all overshoots due to system and/or tester noise. Do not attempt to test these values without suitable equipment. WS57C191C/291C AC READ CHARACTERISTICS Over Operating Range. (See Above) PARAMETER SYMBOL 191C/291C-25 191C/291C-35 191C/291C-45 191C/291C-55 MIN MAX MIN MAX MIN MAX MIN UNITS MAX Address to Output Delay tACC 25 35 45 55 CS to Output Delay tCS 12 20 20 20 Output Disable to Output Float * tDF 12 Address to Output Hold tOH ns 0 20 0 20 0 20 0 *Sampled, Not 100% Tested AC READ TIMING DIAGRAM ADDRESSES VALID tACC tOH CS tCS OUTPUTS VALID tDF 2-9 WS57C191C/291C CAPACITANCE (4) TA = 25C, f = 1 MHz SYMBOL PARAMETER CONDITIONS TYP (5) MAX UNITS C IN Input Capacitance VIN = 0V 4 6 pF C OUT Output Capacitance VOUT = 0V 8 12 pF C VPP VPP Capacitance VPP = 0 V 18 25 pF NOTES: 4. This parameter is only sampled and is not 100% tested. 5.Typical values are for TA = 25C and nominal supply voltages. TEST LOAD (High Impedance Test Systems) A.C. TESTING INPUT/OUTPUT WAVEFORM 98 2.01 V 3.0 1.5 D.U.T. 30 pF (INCLUDING SCOPE AND JIG CAPACITANCE) 0.0 TEST POINTS 1.5 A.C. testing inputs are driven at 3.0 V for a logic "1" and 0.0 V for a logic "0." Timing measurements are made at 1.5 V for input and output transitions in both directions. NOTE: 6. Provide adequate decoupling capacitance as close as possible to this device to achieve the published A.C. and D.C. parameters. A 0.1 microfarad capacitor in parallel with a 0.01 microfarad capacitor connected between VCC and ground is recommended. Inadequate decoupling may result in access time degradation or other transient performance failures. 2-10 WS57C191C/291C NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE TYPICAL ACCESS TIME CHANGE vs. OUTPUT LOADING 1.60 40.0 35.0 1.40 DELTA Taa (ns) NORMALIZED I CC 30.0 1.20 1.00 25.0 20.0 15.0 10.0 0.80 5.0 0.60 0.0 4.0 4.5 5.0 5.5 6.0 0.0 200 SUPPLY VOLTAGE ( V ) 400 600 800 1000 CAPACITANCE ( pF ) NORMALIZED Taa vs. AMBIENT TEMPERATURE NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE 1.6 1.2 1.4 NORMALIZED I CC NORMALIZED Taa 1.1 1.2 1.0 1.0 0.9 0.8 0.6 0.8 -55 -35 -15 5 25 45 65 85 AMBIENT TEMPERATURE (C ) 105 125 -55 -35 -15 5 25 45 65 85 105 125 AMBIENT TEMPERATURE (C) 2-11 WS57C191C/291C PROGRAMMING INFORMATION DC CHARACTERISTICS (TA = 25 5C, VCC = 6.25 V 0.25 V, VPP = 12.75 0.25 V) SYMBOLS PARAMETER MIN MAX UNITS -10 10 A ILI Input Leakage Current (VIN = VCC or Gnd) IPP VPP Supply Current During Programming Pulse 60 mA ICC VCC Supply Current 25 mA VOL Output Low Voltage During Verify (IOL = 16 mA) 0.45 V VOH Output High Voltage During Verify (IOH = -4 mA) 2.4 V NOTES: 8. VPP must not be greater than 13 volts including overshoot. AC CHARACTERISTICS (TA = 25 5C, VCC = 6.25 V 0.25 V, VPP = 12.75 0.25 V) SYMBOLS PARAMETER MIN tAS Address Setup Time tDF Chip Disable Setup Time tDS Data Setup Time tPW Program Pulse Width tDH Data Hold Time tCS Chip Select Delay tRF VPP Rise and Fall Time TYP MAX UNITS 2 s 30 2 s 100 200 2 1 VIH ADDRESS STABLE tAS VIH DATA DATA IN DATA OUT VIL tPW tDS VPP tDH tDF VIH CS1/VPP VIL CS2/CS3 tRF VIH DON'T CARE VIL 2-12 tRF ns s PROGRAMMING WAVEFORM VIL s s 30 ADDRESSES ns tCS WS57C191C/291C ORDERING INFORMATION PART NUMBER SPEED (ns) PACKAGE TYPE OPERATING WSI PACKAGE TEMPERATURE MANUFACTURING DRAWING RANGE PROCEDURE WS57C191C WS57C191C-25D WS57C191C-25J WS57C191C-25P WS57C191C-35D WS57C191C-35J WS57C191C-35P WS57C191C-45D WS57C191C-45DI WS57C191C-45DMB* WS57C191C-45J WS57C191C-45P WS57C191C-55D WS57C191C-55DMB* 25 25 25 35 35 35 45 45 45 45 45 55 55 24 Pin CERDIP, 0.6" 28 Pin PLDCC 24 Pin Plastic DIP, 0.6" 24 Pin CERDIP, 0.6" 28 Pin PLDCC 24 Pin Plastic DIP, 0.6" 24 Pin CERDIP, 0.6" 24 Pin CERDIP, 0.6" 24 Pin CERDIP, 0.6" 28 Pin PLDCC 24 Pin Plastic DIP, 0.6" 24 Pin CERDIP, 0.6" 24 Pin CERDIP, 0.6" D1 J3 P2 D1 J3 P2 D1 D1 D1 J3 P2 D1 D1 Comm'l Comm'l Comm'l Comm'l Comm'l Comm'l Comm'l Industrial Military Comm'l Comm'l Comm'l Military Standard Standard Standard Standard Standard Standard Standard Standard MIL-STD-883C Standard Standard Standard MIL-STD-883C 25 25 35 35 35 45 45 45 45 55 55 24 Pin Plastic DIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin Plastic DIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin Plastic DIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" 24 Pin CERDIP, 0.3" S1 T1 S1 T1 T1 S1 T1 T1 T1 T1 T1 Comm'l Comm'l Comm'l Comm'l Military Comm'l Comm'l Industrial Military Comm'l Military Standard Standard Standard Standard MIL-STD-883C Standard Standard Standard MIL-STD-883C Standard MIL-STD-883C WS57C291C WS57C291C-25S WS57C291C-25T WS57C291C-35S WS57C291C-35T WS57C291C-35TMB* WS57C291C-45S WS57C291C-45T WS57C291C-45TI WS57C291C-45TMB* WS57C291C-55T WS57C291C-55TMB* NOTE: 9. The actual part marking will not include the initials "WS." *SMD product. See section 4 for DESC SMD number. PROGRAMMING/ALGORITHMS/ERASURE/PROGRAMMERS REFER TO PAGE 5-1 The WS57C191C and WS57C291C are programmed using Algorithm D shown on page 5-9. Return to Main Menu 2-13