LM2936-5.0 Ultra-Low Quiescent Current 5V Regulator General Description Features The LM2936 ultra-low quiescent current regulator features low dropout voltage and low current in the standby mode. With less than 15 A quiescent current at a 100 A load, the LM2936 is ideally suited for automotive and other battery operated systems. The LM2936 retains all of the features that are common to low dropout regulators including a low dropout PNP pass device, short circuit protection, reverse battery protection, and thermal shutdown. The LM2936 has a 40V maximum operating voltage limit, a -40C to +125C operating temperature range, and 3% output voltage tolerance over the entire output current, input voltage, and temperature range. The LM2936 is available in a TO-92 package, a SO-8 surface mount package, and a TO-252 surface mount power package. n n n n n n n n n n n n Ultra low quiescent current (IQ 15 A for IO = 100 A) Fixed 5V, 50 mA output 2% Initial output tolerance 3% Output tolerance over line, load, and temperature Dropout voltage typically 200 mV @ IO = 50 mA Reverse battery protection -50V reverse transient protection Internal short circuit current limit Internal thermal shutdown protection 40V operating voltage limit 60V operating voltage limit for LM2936HV Shutdown Pin available with LM2936BM package Typical Application 00975901 * Required if regulator is located more than 2" from power supply filter capacitor. ** Required for stability. Must be rated for 10 F minimum over intended operating temperature range. Effective series resistance (ESR) is critical, see curve. Locate capacitor as close as possible to the regulator output and ground pins. Capacitance may be increased without bound. Connection Diagrams TO-252 SOT-223 00975926 00975925 Top View Order Number LM2936DT-5.0 See NS Package Number TD03B (c) 2002 National Semiconductor Corporation DS009759 Top View Order Number LM2936MP-5.0 See NS Package Number MA04A www.national.com LM2936-5.0 Ultra-Low Quiescent Current 5V Regulator June 2002 LM2936-5.0 Connection Diagrams (Continued) 8-Pin SO (M) 8-Pin SO (M) 00975906 00975927 Top View Order Number LM2936M-5.0, LM2936HVMA-5.0 See NS Package Number M08A Top View Order Number LM2936BM-5.0, LM2936HVBMA-5.0 See NS Package Number M08A TO-92 8-Pin Mini SOIC (MM) 00975902 Bottom View Order Number LM2936Z-5.0 See NS Package Number Z03A www.national.com 00975928 Top View Order Number LM2936MM-5.0 See NS Package Number MUA08A 2 Maximum Operating Input Voltage LM2936 (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Voltage (Survival) Maximum Operating Input Voltage LM2936HV only 2000V Power Dissipation (Note 3) Internally limited Junction Temperature (TJmax) 150C Storage Temperature Range -65C to +150C Lead Temperature (Soldering, 10 sec.) +60V Maximum Shutdown Pin Voltage LM2936BM only +60V, -50V ESD Susceptibility (Note 2) +40V 260C 0V to 40V TO-92 (Z03A) JA 195C/W MSO-8 (MUA08A) JA 200C/W SO-8 (M08A) JA 140C/W SO-8 (M08A) JC 45C/W TO-252 (TD03B) JA 136C/W TO-252 (TD03B) JC Operating Ratings Operating Temperature Range -40C to +125C 6C/W SOT-223 (MA04A) JA 149C/W SOT-223 (MA04A) JC 36C/W Electrical Characteristics VIN = 14V, IO = 10 mA, TJ = 25C, unless otherwise specified. Boldface limits apply over entire operating temperature range Parameter Conditions Min (Note 5) Typical (Note 4) Max (Note 5) Units 4.85 5.00 5.15 V 15 35 mV LM2936HV Only Output Voltage 5.5V VIN 48V, 100 A IO 50 mA (Note 6) Line Regulation 6V VIN 60V, IO = 1mA All LM2936 4.90 5.00 5.10 4.85 5.00 5.15 V IO = 100 A, 8V VIN 24V 9 15 A IO = 10 mA, 8V VIN 24V 0.20 0.50 mA IO = 50 mA, 8V VIN 24V 1.5 2.5 mA 5 10 mV Output Voltage 5.5V VIN 26V, 100 A IO 50 mA (Note 6) Quiescent Current Line Regulation 9V VIN 16V 6V VIN 40V, IO = 1 mA 10 30 Load Regulation 100 A IO 5 mA 10 30 5 mA IO 50 mA 10 30 0.05 0.10 0.20 0.40 V 120 250 mA Dropout Voltage IO = 100 A Short Circuit Current VO = 0V Output Impedance IO = 30 mAdc and 10 mArms, Output Noise Voltage 10 Hz-100 kHz IO = 50 mA f 65 450 mV V m = 1000 Hz 500 V 20 mV/1000 Hr -40 -60 dB -50 -80 V Long Term Stability Ripple Rejection Vripple = 1Vrms, Reverse Polarity RL = 500, T = 1 ms fripple = 120 Hz Transient Input Voltage Output Voltage with VIN = -15V, RL = 500 0.00 -0.30 V Reverse Polarity Input Maximum Line Transient RL = 500, VO 5.5V, T = 40ms 3 60 V www.national.com LM2936-5.0 Absolute Maximum Ratings LM2936-5.0 Electrical Characteristics (Continued) VIN = 14V, IO = 10 mA, TJ = 25C, unless otherwise specified. Boldface limits apply over entire operating temperature range Parameter Min (Note 5) Conditions Output Bypass Capacitance (COUT) ESR COUT = 10F 0.1mA IOUT 50mA Typical (Note 4) Max (Note 5) Units 8 0.010 V 0.3 Shutdown Input - LM2936BM Only Output Voltage, VOUT Output Off, VSD =2.4V, RLOAD = 500 Shutdown High Threshold Voltage, VIH Output Off, RLOAD = 500 Shutdown Low Threshold Voltage, VIL Output On, RLOAD = 500 1.1 Shutdown High Current, IIH Output Off, VSD = 2.4V, RLOAD = 500 12 A Quiescent Current Output Off, VSD = 2.4V, RLOAD = 500 Includes IIHCurrent 30 A 0 2.00 1.1 V 0.60 V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating ratings. Note 2: Human body model, 100 pF discharge through a 1.5 k resistor. Note 3: The maximum power dissipation is a function of TJmax, JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJmax - TA)/JA. If this dissipation is exceeded, the die temperature will rise above 150C and the LM2936 will go into thermal shutdown. Note 4: Typicals are at 25C (unless otherwise specified) and represent the most likely parametric norm. Note 5: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Note 6: To ensure constant junction temperature, pulse testing is used. Typical Performance Characteristics Maximum Power Dissipation (TO-92) Dropout Voltage 00975907 www.national.com 00975908 4 LM2936-5.0 Typical Performance Characteristics (Continued) Dropout Voltage Quiescent Current 00975909 00975910 Quiescent Current Quiescent Current 00975912 00975911 Quiescent Current Quiescent Current 00975914 00975913 5 www.national.com LM2936-5.0 Typical Performance Characteristics (Continued) Output Capacitor ESR Peak Output Current 00975915 00975916 Peak Output Current Current Limit 00975917 00975918 Output at Voltage Extremes Line Transient Response 00975920 00975919 www.national.com 6 LM2936-5.0 Typical Performance Characteristics (Continued) Ripple Rejection Load Transient Response 00975921 00975922 Low Voltage Behavior Output Impedance 00975923 00975924 7 www.national.com LM2936-5.0 On the SO-8 package the four ground pins are thermally connected to the backside of the die. Adding approximately 0.04 square inches of 2 oz. copper pad area to these four pins will improve the JA rating to approximately 110C/W. If this extra pad are is placed directly beneath the package there should not be any impact on board density. Applications Information Unlike other PNP low dropout regulators, the LM2936 remains fully operational to 40V. Owing to power dissipation characteristics of the available packages, full output current cannot be guaranteed for all combinations of ambient temperature and input voltage. As an example, consider an LM2936Z operating at 25C ambient. Using the formula for maximum allowable power dissipation given in (Note 3) , we find that PDmax = 641 mW at 25C. Including the small contribution of the quiescent current to total power dissipation the maximum input voltage (while still delivering 50 mA output current) is 17.3V. The LM2936Z will go into thermal shutdown if it attempts to deliver full output current with an input voltage of more than 17.3V. Similarly, at 40V input and 25C ambient the LM2936Z can deliver 18 mA maximum. On the TO-252 package the ground tab is thermally connected to the backside of the die. Adding 1 square inch of 2 oz. copper pad area directly under the ground tab will improve the JA rating to approximately 50C/W. While the LM2936 has an internally set thermal shutdown point of typically 150C, this is intended as a safety feature only. Continuous operation near the thermal shutdown temperature should be avoided as it may have a negative affect on the life of the device. While the LM2936 maintains regulation to 60V, it will not withstand a short circuit above 40V because of safe operating area limitations in the internal PNP pass device. Above 60V the LM2936 will break down with catastrophic effects on the regulator and possibly the load as well. Do not use this device in a design where the input operating voltage may exceed 40V, or where transients are likely to exceed 60V. Under conditions of higher ambient temperatures, the voltage and current calculated in the previous examples will drop. For instance, at the maximum ambient of 125C the LM2936Z can only dissipate 128 mW, limiting the input voltage to 7.34V for a 50 mA load, or 3.5 mA output current for a 40V input. The junction to ambient thermal resistance JA rating has two distinct components: the junction to case thermal resistance rating JC; and the case to ambient thermal resistance rating CA. The relationship is defined as: JA = JC + CA. For the SO-8 and TO-252 surface mount packages the JA rating can be improved by using the copper mounting pads on the printed circuit board as a thermal conductive path to extract heat from the package. www.national.com Shutdown Pin The LM2936BM has a pin for shutting down the regulator output. Applying a Logic Level High ( > 2.0V) to the Shutdown pin will cause the output to turn off. Leaving the Shutdown pin open, connecting it to Ground, or applying a Logic Level Low ( < 0.6V) will allow the regulator output to turn on. 8 Equivalent Schematic Diagram 00975905 LM2936-5.0 9 www.national.com LM2936-5.0 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead Small Outline Molded Package (M) NS Package Number M08A TO-252 Package (DT) NS Package Number TD03B www.national.com 10 LM2936-5.0 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 3-Lead TO-92 Plastic Package (Z) NS Package Number Z03A SOT-223 Package (MP) NS Package Number MA04A 11 www.national.com LM2936-5.0 Ultra-Low Quiescent Current 5V Regulator Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 8-Lead Mini SOIC package (MM) NS Package Number MUA08A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. National P/N LM2936-5.0 - Ultra-Low Quiescent Current 5V Regulator See A/D Converters Products Products > Analog - Regulators > Linear Regulators - Low Dropout Voltage > Positive Voltage - Fixed > LM2936-5.0 LM2936-5.0 Product Folder Ultra-Low Quiescent Current 5V Regulator Generic P/N 2936-5.0 General Description Features Package & Models Datasheet Parametric Table Samples & Pricing Parametric Table Multiple Output Capability No Dropout Voltage, typ (Volt) .20 On/Off Pin Yes Quiescent Current, typ (mA) .0090 Error Flag No Secondary Ouput Voltage (Volt) - Input Voltage, min (Volt) 5.50 Secondary Output Current (Amp) - Input Voltage, max (Volt) 60 Output Voltage (Volt) 5 Output Current, max 50 mA Watchdog No Datasheet Size in Date Kbytes Title LM2936-5.0 Ultra-Low Quiescent Current 5V Regulator LM2936-5.0 Ultra-Low Quiescent Current 5V Regulator (JAPANESE) View Online Download 24416 Jun- View Online Kbytes 02 Download 189 Kbytes Download View Online Receive via Email Receive via Email Receive via Email If you have trouble printing or viewing PDF file(s), see Printing Problems. Package Availability, Models, Samples & Pricing Package Part Number Status Type LM2936BM-5.0 SOIC NARROW Pins MSL 8 Budgetary Samples & Pricing Electronic $US Orders SPICE IBIS Qty each Models Full MSL production Samples N/A N/A Buy Now 1K+ $0.7700 Std Pack Size Package Marking rail of 95 [logo]2T LM293 6B5.0 file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM2936-5.0.html (1 of 3) [Aug-09-2002 2:55:05 PM] National P/N LM2936-5.0 - Ultra-Low Quiescent Current 5V Regulator 1K+ $0.8600 rail of 95 [logo]2T 2936H BM5.0 1K+ $0.8600 rail of 95 [logo]2T 2936H M-5.0 1K+ $0.7500 rail of 95 [logo]2T LM293 6M-5 1K+ $0.7700 reel of 2500 [logo]2T LM293 6B5.0 N/A 1K+ $0.8600 reel of 2500 [logo]2T 2936H BM5.0 N/A N/A 1K+ $0.8600 reel of 2500 [logo]2T 2936H M-5.0 Full production N/A N/A 1K+ $0.7500 reel of 2500 [logo]2T LM293 6M-5 Full production N/A N/A 1K+ $0.8600 reel of 1000 2T KAAA MSL Full production N/A N/A 1K+ $0.8600 reel of 2000 2T KAAA MSL Full production N/A N/A 1K+ $0.7500 reel of 1000 Z1T KBA MSL Full production N/A N/A 1K+ $0.7500 reel of 3500 Z1T KBA 3 MSL Full production N/A N/A 1K+ $0.8600 rail of 75 [logo]UZ2T LM2936D T-5.0 TO 252 3 MSL Full production N/A N/A TO 92 3 MSL Full production N/A N/A 24 Hour Samples Buy Now Die Full production N/A N/A Samples Wafer Full production LM2936HVBMA-5.0 SOIC NARROW 8 MSL Full production N/A N/A LM2936HVMA-5.0 SOIC NARROW 8 MSL Full production N/A N/A LM2936M-5.0 SOIC NARROW 8 MSL Full production N/A N/A LM2936BMX-5.0 SOIC NARROW 8 MSL Full production N/A N/A LM2936HVBMAX5.0 SOIC NARROW 8 MSL Full production N/A LM2936HVMAX-5.0 SOIC NARROW 8 MSL Full production LM2936MX-5.0 SOIC NARROW 8 MSL LM2936MP-5.0 SOT-223 4 MSL LM2936MPX-5.0 SOT-223 4 LM2936MM-5.0 MINI SOIC 8 MINI SOIC 8 LM2936DT-5.0 TO 252 LM2936DTX-5.0 LM2936MMX-5.0 LM2936Z-5.0 LM2936-5.0 MDC LM2936-5.0 MWC Samples Samples Buy Now 24 Hour Samples Buy Now Buy Now Buy Now Samples Buy Now Samples Buy Now N/A N/A 24 Hour Samples Buy Now 1K+ $0.8600 reel [logo]UZ2T of LM2936D 2500 T-5.0 1K+ $0.8600 box of 1800 [logo]2T LM293 6Z-5 tray of N/A - wafer jar of N/A - General Description file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM2936-5.0.html (2 of 3) [Aug-09-2002 2:55:05 PM] National P/N LM2936-5.0 - Ultra-Low Quiescent Current 5V Regulator The LM2936 ultra-low quiescent current regulator features low dropout voltage and low current in the standby mode. With less than 15 A quiescent current at a 100 A load, the LM2936 is ideally suited for automotive and other battery operated systems. The LM2936 retains all of the features that are common to low dropout regulators including a low dropout PNP pass device, short circuit protection, reverse battery protection, and thermal shutdown. The LM2936 has a 40V maximum operating voltage limit, a -40C to +125C operating temperature range, and 3% output voltage tolerance over the entire output current, input voltage, and temperature range. The LM2936 is available in a TO-92 package, a SO-8 surface mount package, and a TO-252 surface mount power package. Features Ultra low quiescent current (IQ <= 15 A for IO = 100 A) Fixed 5V, 50 mA output 2% Initial output tolerance 3% Output tolerance over line, load, and temperature Dropout voltage typically 200 mV @ IO = 50 mA Reverse battery protection -50V reverse transient protection Internal short circuit current limit Internal thermal shutdown protection 40V operating voltage limit 60V operating voltage limit for LM2936HV Shutdown Pin available with LM2936BM package [Information as of 5-Aug-2002] Search Design Purchasing Quality Company Home About Languages . Website Guide . About "Cookies" . National is QS 9000 Certified . Privacy/Security Statement . Contact Us . Site Terms & Conditions of Use . Copyright 2002 (c) National Semiconductor Corporation . My Preferences . Feedback file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM2936-5.0.html (3 of 3) [Aug-09-2002 2:55:05 PM]