Single IDC Contact 22-28 AWG: WTB INTERCONNECT 9176-400 The 917X series of surface mount Insulation Displacement Connectors (IDC) were developed to meet the harsh automotive and industrial market applications for connecting individual wires directly to a PCB ranging from 14 AWG to 28 AWG. This industry proven contact system has been tested to automotive levels of shock, vibration, and temperature cycling to prove their reliability and robustness. This new single contact was developed as a standalone component to enhance the application uses with the IDC technology. The simplicity of inserting a wire into an SMT contact with a small tool or optional retention / termination cap allows a wide range of devices to be connected to the PCB without soldering. In SSL applications specifically, these contacts are used to bring power and signal onto the PCB or are used to daisy chain multiple boards together in a long string. While the IDC contact provides a gas-tight connection to conductor of the wire, the optional cap provides a positive strain relief even in the harshest conditions. In case of repair, the wires can be removed and replace up to three times. The single 9176-400 series contact and cap accepts 22 AWG to 28 AWG wires with an insulation diameter ranging from 1.0mm to 1.5mm. These dual beam contacts support a 6 amp current rating with a large SMT solder base to provide maximum stability on the PCB. The optional locking strain relief cap acts as the termination tool for severe vibration applications. APPLICATIONS * Connecting discrete wire components directly to the PCB * Bringing power and signals onto a PCB * Daisy chaining PCB's together to create a continuous string of boards * Application notes: refer to 201-01-124 FEATURES AND BENEFITS * * * * * * IDC contact is supplied in T&R pockets for standard SMT placement IDC contact provides a gas-tight connection to the PCB for long term reliability Optional termination cap provides additional strain relief for severe environments Tested to automotive levels on shock, vibration and temperature cycling for reliability Reduced total applied cost versus solder or crimp processes Individual contacts can be located anywhere on the PCB based on specific application ELECTRICAL ENVIRONMENTAL MECHANICAL * Current Rating: 6 Amps/Contact * Voltage Rating: Dependant on component proximity * Operating Temperature: -40C to +125C * * * * Insulator Material: Nylon 46: UL94V0 Contact Material: Phosphor Bronze Plating: Tin over Nickel Durability: 3 Cycles HOW TO ORDER - CONTACT OPTIONS 70 9176 001 Prefix 70 = Contact Series Number of Ways No of Code Ways Details 001 1 Page 2 Code 422 432 442 443 4XX 006 Wire Gauge Size Plating Option 006 = Pure Tin all over Accepted Wire Gauge 22 Gauge Solid or Stranded 24 Gauge Solid or Stranded 26 Gauge Solid or Stranded 28 Gauge Solid or Stranded HOW TO ORDER - CAP OPTIONS 60 9176 001 Prefix 60 = Cap Series Number of Ways No of Code Ways Details 001 1 Page 6 415 X00 Wire Gauge Size Code 415 Wire Insulation O 0.75-1.5 Insulator Color Code Color 000 Black 100 White Application Industrial Lighting CONNECTOR/TOOLING PART NUMBER MATRIX AWG 22 24 26 28 SERIES 9176-500 IDC HAND INSERTION TOOLING* ACCESSORY CAPS Wire Plastic Metal Cap Application Positions Part Number White Black Insulation (medium volume) (high volume) Tool O 1.0 - 1.5 1p 709176001422006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 O 1.0 - 1.5 1p 709176001432006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 O 0.7 - 1.0 1p 709176001443006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 O 0.7 - 1.0 1p 709176001443006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 * Hand Insertion Tooling and Cap Application - Universal Hand Tool 067000773001000; Consult Application Notes 201-01-124 Certification: UL File #E90723 1 Single IDC Contact 22-28 AWG: WTB INTERCONNECT 9176-400 CONTACT DETAILS Code 422 432 442 443 Accepted Wire Gauge 22AWG Solid or Stranded 24AWG Solid or Stranded 28AWG Solid or Stranded 26-28AWG Solid or Stranded A 0.47 0.37 0.28 0.20 NOTES: 1. CONNECTOR FOR IDC WIRE TO BOARD CONNECTION. 2. CONTACT MATERIAL: PHOSPHOR BRONZE. 3. CONTACT PLATING: PURE TIN. 4. CONNECTOR DESIGNED TO ACCEPT BETWEEN 22AWG AND 28AWG SOLID AND STRANDED WIRE, SEE TABLE. 5. ALL DIMENSIONS 0.20 UNLESS TOLERANCED. 6. FOR FULL PRODUCT SPECIFICATION REFER TO ELCO SPEC 201-01-126 AND APPLICATION NOTES 201-01-124. 7. SMT PCB LAYOUT, REFER TO PAGE 3. 8. PACKING IN TAPE AND REEL, QUANTITY 2000 PER REEL. 9. WHEN REQUIRED, MATCHING CAP DETAILS ON DRAWING 60-9176-001-4XX-X06S. 10. ASSEMBLY TOOLING ON PAGE 5 FOR WIRE INTO CONTACT AND PAGE 4 FOR CAP. 11. UL REFERENCE E90723, THIS UL REFERENCE ALSO APPLIES WHEN COMBINED WITH AVX SPECIFIED OPTIONAL CAP. PACKING DETAILS REEL QTY LEADER TRAILER 2 2 000 480MM 120MM Single IDC Contact 22-28 AWG: WTB INTERCONNECT 9176-400 22-28 AWG IDC WIRE TO BOARD CONNECTOR SINGLE CONTACT SMT PCB LAYOUT PURE TIN PADS ORIENTATION OF CONTACT ON PAD ASSEMBLED/INSTALLED PRODUCTS NOTES: 1. CONNECTOR CAN BE USED WITH CONTACT ONLY OR WITH OPTIONAL CAP. 2. OUTLINE OF CAP WHERE USED. 3. FOR FULL PRODUCT SPECIFICATION REFER TO ELCO SPEC 201-01-126 AND APPLICATION NOTES 201-01-124. 4. ALL DIMENSIONS 0.20 UNLESS TOLERANCED. 5. ASSEMBLY TOOLING ON PAGE 5 FOR WIRE INTO CONTACT AND PAGE 4 FOR CAP. 6. WIRE CENTER LINE HEIGHT ABOVE THE PCB. THIS INCLUDES AN ALLOWANCE OF 0.10MM FOR SOLDER AND 0.035MM FOR PAD THICKNESS. NO ALLOWANCE HAS BEEN MADE FOR SOLDER RESIST OR OTHER FEATURES. 3 Single IDC Contact 22-28 AWG: WTB INTERCONNECT 9176-400 ASSEMBLY TOOLING - CAP USED NOTES: 1. ASSEMBLY TOOLING FOR CAP. 2. MINIMUM AREA OF PCB TO BE KEPT CLEAR OF COMPONENTS, TRACKS PERMISSIBLE. 3. WIRE AND CAP INSERTED IN ONE OPERATION. 4. REFER TO APPLICATION NOTE 201-01-124 FOR FURTHER INFORMATION. 5. REFER TO PAGE 5 FOR ASSEMBLY WITHOUT CAP. CAP APPLICATION TOOL - PLASTIC METAL TOOL - HIGH VOLUME 06-9176-7023-01-000 06-9176-7024-01-000 ORIENTATE CAP IN TOOL UNIVERSAL HANDLE 06-7000-7730-01-000 CONNECTOR/TOOLING PART NUMBER MATRIX AWG 22 24 26 28 4 SERIES 9176-400 IDC HAND INSERTION TOOLING* ACCESSORY CAPS Wire Plastic Metal Cap Application Positions Part Number White Black Insulation (medium volume) (high volume) Tool O 1.0 - 1.5 1p 709176001422006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 O 1.0 - 1.5 1p 709176001432006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 O 0.7 - 1.0 1p 709176001443006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 O 0.7 - 1.0 1p 709176001443006 069176702201000 069176702101000 069176702301000 609176001415100 609176001415000 * Hand Insertion Tooling and Cap Application - Universal Hand Tool 067000773001000; Consult Application Notes 201-01-124 Single IDC Contact 22-28 AWG: WTB INTERCONNECT 9176-400 ASSEMBLY TOOLING - CAP NOT USED WIRE ONTO CONTACT METAL TOOL HIGH VOLUME PLASTIC TOOL LOW/MEDIUM VOLUME 06-9176-7021-01-000 06-9176-7022-01-000 UNIVERSAL HANDLE 06-7000-7730-01-000 NOTES: 1. ASSEMBLY TOOLING FOR CONTACT ONLY. NO CAP USED. 2. MINIMUM AREA OF PCB TO BE KEPT CLEAR OF COMPONENTS, TRACKS PERMISSIBLE. 3. REFER TO APPLICATION NOTE 201-01-124 FOR FURTHER INFORMATION. 4. INSERT CORRECT TOOL INTO HANDLE, MAGNETIC RETENTION. 5. REFER TO PAGE 4 FOR ASSEMBLY WITH CAP. 5 Single IDC Contact 22-28 AWG: WTB 9176-400 INTERCONNECT CAP DETAILS NOTES: 1. CAP FOR IDC WIRE TO BOARD CONNECTION. 2. CAP MATERIAL: GLASS FILLED NYLON 46, COLOR SEE PAGE 1. 3. CAPS DESIGNED TO ACCOMMODATE WIRE INSULATION DIAMETERS 0.75MM TO 1.5MM. 4. ALL DIMENSIONS 0.20 UNLESS TOLERANCED. 5. FOR FULL PRODUCT SPECIFICATION REFER TO ELCO SPEC 201-01-126, APPLICATION NOTES 201-01-124. 6. PACKING IN BAGS, QUANTITY 2000 PER BAG. 7. FOR INSTALATION DETAILS REFER TO DRAWING 70-9176-001-4XX-006S. 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: AVX: 067000773001000