MDO3BND-PROMO - TEKTRONIX - Datasheet.Live

Mixed Domain Oscilloscopes

MDO3000 Series Datasheet

Today's integrated designs need an oscilloscope that is just as integrated -

such as the MDO3000 Mixed Domain Oscilloscope (MDO) Series. It is the

ultimate 6-in-1 integrated oscilloscope that includes an integrated spectrum

analyzer, arbitrary function generator, logic analyzer, protocol analyzer, and

digital voltmeter/counter. The MDO3000 is completely customizable and

fully upgradeable. Add the instruments and performance you need now - or

later.

Key performance specifications

Oscilloscope

2 and 4 analog channel models

1 GHz, 500 MHz, 350 MHz, 200 MHz, 100 MHz bandwidth models

Bandwidth is upgradable (up to 1 GHz)

Up to 5 GS/s sample rate

10 M record length on all channels

>280,000 wfm/s maximum waveform capture rate

Standard passive voltage probes with 3.9 pF capacitive loading

and 1 GHz, 500 MHz, or 250 MHz analog bandwidth

Spectrum Analyzer

Frequency range

Standard: 9 kHz - oscilloscope bandwidth

Optional: 9 kHz - 3 GHz

Ultra-wide capture bandwidth up to 3 GHz

Arbitrary Function Generator (Optional)

13 predefined waveform types

50 MHz waveform generation

128 k arbitrary generator record length

250 MS/s arbitrary generator sample rate

Logic Analyzer (Optional)

16 digital channels

10 M record length on all channels

121.2 ps timing resolution

Protocol Analyzer (Optional)

Serial bus support for I2C, SPI, RS-232/422/485/UART, USB 2.0,

CAN, LIN, FlexRay, MIL-STD-1553, and Audio standards

Digital Voltmeter (Free with product registration)

4-digit AC RMS, DC, and AC+DC RMS voltage measurements

5-digit frequency measurements

Key features

FastAcq™ high-speed waveform capture rate finds elusive signal

anomalies quickly

Wave Inspector® Controls provide easy navigation and automated

search of waveform data

33 automated measurements and waveform histograms for simplified

waveform analysis

TekVPI® probe interface directly supports active, differential, and

current probes for automatic scaling and units

9 in. (229 mm) WVGA widescreen color display

Small footprint and lightweight – Only 5.8 in. (147 mm) deep and 9.2 lb.

(4.2 kg)

Spectral Analysis

Dedicated front-panel controls for commonly performed tasks

Automated peak markers identify frequency and amplitude of

spectrum peaks

Manual markers enable non-peak measurements

Trace types include: Normal, Average, Max Hold, and Min Hold

Spectrogram display enables easy observation and insight into

slowly changing RF phenomena

Automated measurements include: Channel Power, Adjacent

Channel Power Ratio (ACPR), and Occupied Bandwidth (OBW)

Arbitrary Function Generation

Generate predefined signals to quickly simulate missing devices in

designs

Capture signals on analog or digital inputs, transfer to the arbitrary

edit memory, and replicate out from the AFG

Add noise to any signal to easily perform margin testing

www.tektronix.com 1

Mixed signal design and analysis

Automated triggering, decode, and search on parallel buses

Multichannel setup and hold triggering

MagniVu™ high-speed acquisition provides 121.2 ps fine timing

resolution on digital channels

Protocol Analysis

Trigger, decode and automatically search on packet-level content

on most common embedded design serial bus standards.

Export protocol decode tables for use in documenting results

Digital Voltmeter and Frequency Counter

Quickly validate voltage or frequency measurements at a glance

Graphical readout provides information on stability of the

measurement

Fully upgradeable

Add functionality, increase bandwidth or spectrum analyzer

frequency range over time as your needs change or budget allows

Optional application support

Power analysis

Limit and mask testing

Need more performance?

Need more input frequency range on the spectrum analyzer?

Need to analyze analog, digital, and RF simultaneously?

Need more record length or a larger display?

Consider the MDO4000B Series oscilloscopes www.tektronix.com/MDO4000

► 3 GHz and 6 GHz integrated spectrum analyzers

► Simultaneous acquisition of analog, digital and RF

► 20 M record length

► 10.4 inch XGA display

Oscilloscope

At the core of the MDO3000 Series is a world-class oscilloscope, offering

comprehensive tools that speed each stage of debug – from quickly

discovering anomalies and capturing them, to searching your waveform

record for events of interest and analyzing their characteristics and your

device’s behavior.

Digital phosphor technology with FastAcq™ high-

speed waveform capture

To debug a design problem, first you must know it exists. Every design

engineer spends time looking for problems in their design, a time-

consuming and frustrating task without the right debug tools.

Digital phosphor technology provides you with fast insight into the real

operation of your device. Its fast waveform capture rate – greater than

280,000 wfm/s with FastAcq – gives you a high probability of quickly seeing

the infrequent problems common in digital systems: runt pulses, glitches,

timing issues, and more.

To further enhance the visibility of rarely occurring events, intensity grading

is used to indicate how often rare transients are occurring relative to normal

signal characteristics. There are four waveform palettes available in

FastAcq acquisition mode.

The Temperature palette uses color-grading to indicate frequency of

occurrence with hot colors like red/yellow indicating frequently

occurring events and colder colors like blue/green indicating rarely

occurring events.

The Spectral palette uses color-grading to indicate frequency of

occurrence with colder colors like blue indicating frequently occurring

events and hot colors like red indicating rarely occurring events.

The Normal palette uses the default channel color (like yellow for

channel one) along with gray-scale to indicate frequency of occurrence

where frequently occurring events are bright.

The Inverted palette uses the default channel color along with gray-

scale to indicate frequency of occurrence where rarely occurring events

are bright.

These color palettes quickly highlight the events that over time occur more

often or, in the case of infrequent anomalies, occur less often.

Infinite or variable persistence choices determine how long waveforms stay

on the display, helping you to determine how often an anomaly is occurring.

Datasheet

2 www.tektronix.com

Digital phosphor technology with FastAcq enables greater than 280,000 wfms/s

waveform capture rate and real-time color-intensity grading.

Triggering

Discovering a device fault is only the first step. Next, you must capture the

event of interest to identify root cause. To enable this, the MDO3000

contains over 125 trigger combinations providing a complete set of triggers

- including runt, logic, pulse width/glitch, setup and hold violation, serial

packet, and parallel data - to help quickly locate your event of interest. And

with up to a 10 M record length, you can capture many events of interest,

even thousands of serial packets, in a single acquisition for further analysis

while maintaining high resolution to zoom in on fine signal details.

Over 125 trigger combinations make capturing your event of interest easy.

Wave Inspector® waveform navigation and automated

With long record lengths, a single acquisition can include thousands of

screens of waveform data. Wave Inspector®, the industry’s best tool for

waveform navigation and automated search, enables you to find events of

interest in seconds.

Wave Inspector controls provide unprecedented efficiency in viewing, navigating, and

analyzing waveform data. Zip through your long record by turning the outer pan control

(1). Get details from the beginning to end in seconds. See something of interest and want

to see more details? Just turn the inner zoom control (2).

Zoom and pan

A dedicated, two-tier front-panel control provides intuitive control of both

zooming and panning. The inner control adjusts the zoom factor (or zoom

scale); turning it clockwise activates zoom and goes to progressively higher

zoom factors, while turning it counterclockwise results in lower zoom

factors and eventually turning zoom off. No longer do you need to navigate

through multiple menus to adjust your zoom view. The outer control pans

the zoom box across the waveform to quickly get to the portion of waveform

you are interested in. The outer control also utilizes force-feedback to

determine how fast to pan on the waveform. The farther you turn the outer

control, the faster the zoom box moves. Pan direction is changed by simply

turning the control the other way.

User marks

Press the Set Mark front-panel button to place one or more marks on the

waveform. Navigating between marks is as simple as pressing the

Previous (←) and Next (→) buttons on the front panel.

Search marks

The Search button allows you to automatically search through your long

acquisition looking for user-defined events. All occurrences of the event are

highlighted with search marks and are easily navigated to, using the front-

panel Previous (←) and Next (→) buttons. Search types include edge,

pulse width/glitch, timeout, runt, logic, setup and hold, rise/fall time, parallel

bus, and I2C, SPI, RS-232/422/485/UART, USB 2.0, CAN, LIN, FlexRay,

MIL-STD-1553, and Audio packet content. A search mark table provides a

tabular view of the events found during the automated search. Each event

is shown with a time stamp, making timing measurements between events

easy.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 3

Search step 1: You define what you would like to find.

Search step 2: Wave Inspector automatically searches through the record and marks

each event with a hollow white triangle. You can then use the Previous and Next buttons

to jump from one event to the next.

Search step 3: The Search Mark table provides a tabular view of each of the events

found by the automated search. Each event is shown with a time stamp making timing

measurements between events easy.

Waveform analysis

Verifying that your prototype’s performance matches simulations and meets

the project’s design goals requires analyzing its behavior. Tasks can range

from simple checks of rise times and pulse widths to sophisticated power

loss analysis and investigation of noise sources.

The oscilloscope offers a comprehensive set of integrated analysis tools

including waveform- and screen-based cursors, automated measurements,

advanced waveform math including arbitrary equation editing, FFT

analysis, waveform histograms, and trend plots for visually determining how

a measurement is changing over time.

Automated measurement readouts provide repeatable, statistical views of waveform

characteristics.

Each measurement has help text and graphics associated with it that help explain how

the measurement is made.

Waveform histograms show visually how waveforms vary over time.

Horizontal waveform histograms are especially useful for gaining insight

into how much jitter is on a clock signal, and what the distribution of that

jitter is. Vertical histograms are especially useful for gaining insight into how

much noise is on a signal, and what the distribution of that noise is.

Measurements taken on a waveform histogram provide analytical

information about the distribution of a waveform histogram, providing

insight into just how broad a distribution is, the amount of standard

deviation, the mean value, etc.

Datasheet

4 www.tektronix.com

Waveform histogram of a rising edge showing the distribution of edge position (jitter) over

time. Included are numeric measurements made on the waveform histogram data.

Video design and development

Many video engineers have remained loyal to analog oscilloscopes,

believing the intensity gradations on an analog display are the only way to

see certain video waveform details. The fast waveform capture rate of the

MDO3000, coupled with its intensity-graded view of the signal, provides the

same information-rich display as an analog oscilloscope, but with much

more detail and all the benefits of digital scopes.

Standard features such as IRE and mV graticules, holdoff by fields, video

polarity, HDTV and custom (nonstandard) video triggers, and an Autoset

smart enough to detect video signals, make these the easiest to use

oscilloscopes on the market for video applications. And with high

bandwidth, four analog inputs, and a built-in 75 Ω input termination (not

available on 1 GHz models), the oscilloscope provides ample performance

for analog and digital video use. There is even a video picture mode

enabling you to see the picture of the video signal you are viewing – for

NTSC and PAL signals.

Viewing an NTSC video signal. Notice the intensity-graded view provided by the

MDO3000's ability to represent time, amplitude, and distribution over time.

Viewing an NTSC full color bar signal image. Video picture mode contains automatic

contrast and brightness settings as well as manual controls.

Power analysis (optional)

Ever increasing consumer demands for longer battery-life devices and for

green solutions that consume less power require power-supply designers to

characterize and minimize switching losses to improve efficiency. In

addition, the supply’s power levels, output purity, and harmonic feedback

into the power line must be characterized to comply with national and

regional power quality standards. Historically, making these and many

other power measurements on an oscilloscope has been a long, manual,

and tedious process. The MDO3000’s optional power analysis tools greatly

simplify these tasks, enabling quick, repeatable and accurate analysis of

power quality, switching loss, harmonics, safe operating area (SOA),

modulation, ripple, and slew rate (di/dt, dv/dt). Completely integrated into

the oscilloscope, the power analysis tools provide automated, repeatable

power measurements with a touch of a button.

Power Quality measurement table. Automated power measurements enable quick and

accurate analysis of common power parameters.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 5

Limit/Mask testing (optional)

A common task during the development process is characterizing the

behavior of certain signals in a system. One method, called limit testing, is

to compare a tested signal to a known good or "golden" version of the

same signal with user-defined vertical and horizontal tolerances. Another

common method, called mask testing, is to compare a tested signal to a

mask, looking for where a signal under test violates the mask. The

MDO3000 Series offers both limit and mask testing capability useful for

long-term signal monitoring, characterizing signals during design, or testing

on a production line. Tailor a test to your specific requirements by defining

test duration in number of waveforms or time, a violation threshold that

must be met before considering a test a failure, counting hits along with

statistical information, and actions upon violations, test failure, and test

complete. Whether specifying a mask from a known good signal or from a

custom mask, conducting pass/fail tests in search of waveform anomalies

such as glitches has never been easier.

Limit Test showing a mask created from a golden waveform and compared against a live

signal. Results showing statistical information about the test are displayed.

Standard passive voltage probes

The MDO3000 Series include passive voltage probes with industry best

capacitive loading of only 3.9 pF. The included TPP probes minimize the

impact on devices under test and accurately deliver signals to the

oscilloscope for acquisition and analysis. The following table shows which

TPP probes come standard with each MDO3000 model.

MDO3000 model Included probe

MDO3012, MDO3014,

MDO3022, MDO3024

TPP0250: 250 MHz, 10x passive voltage

probe. One per analog channel

MDO3032, MDO3034,

MDO3052, MDO3054

TPP0500B: 500 MHz, 10x passive

voltage probe. One per analog channel

MDO3102, MDO3104 TPP1000: 1 GHz, 10x passive voltage

probe. One per analog channel

TekVPI® probe interface

The TekVPI probe interface sets the standard for ease of use in probing. In

addition to the secure, reliable connection that the interface provides,

TekVPI probes feature status indicators and controls, as well as a probe

menu button right on the comp box itself. This button brings up a probe

menu on the oscilloscope display with all relevant settings and controls for

the probe. The TekVPI interface enables direct attachment of current

probes without requiring a separate power supply. TekVPI probes can be

controlled remotely through USB, GPIB, or LAN, enabling more versatile

solutions in ATE environments. The TekVPI inputs provide up to 25 W of

power to the front panel connectors from the internal power supply.

TekVPI probe interface simplifies connecting your probes to the oscilloscope.

Remote connectivity and instrument control

Exporting data and measurements is as simple as connecting a USB cable

from the oscilloscope to your PC. Key software applications –

OpenChoice® Desktop, and Microsoft Excel and Word toolbars – are

included standard with each oscilloscope to enable fast and easy direct

communication with your Windows PC.

The included OpenChoice Desktop enables fast and easy communication

between the oscilloscope and your PC through USB or LAN for transferring

settings, waveforms, and screen images.

The embedded e*Scope® capability enables fast control of the oscilloscope

over a network connection through a standard web browser. Simply enter

the IP address or network name of the oscilloscope and a web page will be

served to the browser. Transfer and save settings, waveforms,

measurements, and screen images or make live control changes to settings

on the oscilloscope directly from the web browser.

Datasheet

6 www.tektronix.com

e*Scope in a web browser showing the display of an MDO3000. Use e*Scope to quickly

document your work by saving screen images, waveforms, or setups for later use.

Spectrum Analyzer

The MDO3000 is the first oscilloscope in its class to include an integrated

spectrum analyzer. Each oscilloscope includes a spectrum analyzer with a

frequency range of 9 kHz up to the analog bandwidth of the instrument. The

spectrum analyzer frequency range of each instrument can be upgraded

from 9 kHz to 3 GHz (option MDO3SA), enabling spectral analysis on most

consumer wireless standards.

Fast and accurate spectral analysis

When using the spectrum analyzer input, the MDO3000 Series display

becomes a full-screen Frequency Domain view.

Key spectral parameters such as Center Frequency, Span, Reference

Level, and Resolution Bandwidth are all adjusted quickly and easily using

the dedicated front-panel menus and keypad.

MDO3000 frequency domain display.

Key spectral parameters are adjusted quickly with the dedicated front-panel menus and

keypad.

Intelligent, efficient markers

In a traditional spectrum analyzer, it can be a very tedious task to turn on

and place enough markers to identify all your peaks of interest. The

MDO3000 Series makes this process far more efficient by automatically

placing markers on peaks that indicate both the frequency and the

amplitude of each peak. You can adjust the criteria that the oscilloscope

uses to automatically find the peaks.

The highest amplitude peak is referred to as the reference marker and is

shown in red. Marker readouts can be switched between Absolute and

Delta readouts. When Delta is selected, marker readouts show each peak's

delta frequency and delta amplitude from the reference marker.

Two manual markers are also available for measuring non-peak portions of

the spectrum. When enabled, the reference marker is attached to one of

the manual markers, enabling delta measurements from anywhere in the

spectrum. In addition to frequency and amplitude, manual marker readouts

also include noise density and phase noise readouts depending on whether

Absolute or Delta readouts are selected. A "Reference Marker to Center"

function instantly moves the frequency indicated by the reference marker to

center frequency.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 7

Automated peak markers identify critical information at a glance. As shown here, the five

highest amplitude peaks that meet the threshold and excursion criteria are automatically

marked along with the peak's frequency and amplitude.

Spectrogram

The MDO3000 Series includes a spectrogram display which is ideal for

monitoring slowly changing RF phenomena. The x-axis represents

frequency, just like a typical spectrum display. However, the y-axis

represents time, and color is used to indicate amplitude.

Spectrogram slices are generated by taking each spectrum and "flipping it

up on its edge" so that it's one pixel row tall, and then assigning colors to

each pixel based on the amplitude at that frequency. Cold colors (blue,

green) are low amplitude and hotter colors (yellow, red) are higher

amplitude. Each new acquisition adds another slice at the bottom of the

spectrogram and the history moves up one row. When acquisitions are

stopped, you can scroll back through the spectrogram to look at any

individual spectrum slice.

Spectrogram display illustrates slowly moving RF phenomena. As shown here, a signal

that has multiple peaks is being monitored. As the peaks change in both frequency and

amplitude over time, the changes are easily seen in the Spectrogram display.

Ultra-wide capture bandwidth

Today's wireless communications vary significantly with time, using

sophisticated digital modulation schemes and, often, transmission

techniques that involve bursting the output. These modulation schemes can

have very wide bandwidth as well. Traditional swept or stepped spectrum

analyzers are ill equipped to view these types of signals as they are only

able to look at a small portion of the spectrum at any one time.

The amount of spectrum acquired in one acquisition is called the capture

bandwidth. Traditional spectrum analyzers sweep or step the capture

bandwidth through the desired span to build the requested image. As a

result, while the spectrum analyzer is acquiring one portion of the spectrum,

the event you care about may be happening in another portion of the

spectrum. Most spectrum analyzers on the market today have 10 MHz

capture bandwidths, sometimes with expensive options to extend that to

20, 40, or even 160 MHz in some cases.

In order to address the bandwidth requirements of modern RF, the

MDO3000 Series provides up to 3 GHz of capture bandwidth. The

spectrum is generated from a single acquisition, thus guaranteeing you'll

see the events you're looking for in the frequency domain.

Spectral display of a bursted communication both into a device through Zigbee at

900 MHz and out of the device through Bluetooth at 2.4 GHz, captured with a single

acquisition.

Spectrum traces

The MDO3000 Series spectrum analyzer offers four different traces or

views including Normal, Average, Max Hold, and Min Hold.

Datasheet

8 www.tektronix.com

Normal, Average, Max Hold, and Min Hold spectrum traces

RF measurements

The MDO3000 Series includes three automated RF measurements -

Channel Power, Adjacent Channel Power Ratio, and Occupied Bandwidth.

When one of these RF measurements is activated, the oscilloscope

automatically turns on the Average spectrum trace and sets the detection

method to Average for optimal measurement results.

Automated Channel Power measurement

Advanced RF analysis

The MDO3000 can save the baseband I and Q data from spectrum

analyzer acquisitions to a .TIQ file. These files can then be imported into

Tektronix SignalVu-PC software for general purpose modulation and pulse

analysis or RSAVu for analysis of commercial wireless standards.

RF probing

Signal input methods on spectrum analyzers are typically limited to cabled

connections or antennas. But with the optional TPA-N-VPI adapter, any

active, 50 Ω TekVPI probe can be used with the spectrum analyzer on the

MDO3000 Series. This enables additional flexibility when hunting for noise

sources and enables easier spectral analysis by using true signal browsing

on a spectrum analyzer input.

In addition, an optional preamplifier accessory assists in the investigation of

lower-amplitude signals. The TPA-N-PRE preamplifier provides 10 dB

nominal gain across the 9 kHz – 3 GHz frequency range.

The optional TPA-N-VPI adapter enables any active, 50 Ω TekVPI probe to be

connected to the RF input.

Arbitrary Function Generator (optional)

The MDO3000 contains an optional integrated arbitrary function generator

(option MDO3AFG), perfect for simulating sensor signals within a design or

adding noise to signals to perform margin testing.

The integrated function generator provides output of predefined waveforms

up to 50 MHz for sine, square, pulse, ramp/triangle, DC, noise, sin(x)/x

(Sinc), Gaussian, Lorentz, exponential rise/fall, Haversine and cardiac.

The arbitrary waveform generator provides 128 k points of record for

storing waveforms from the analog input, a saved internal file location, a

USB mass storage device, or from an external PC. Once a waveform is in

the edit memory of the arbitrary waveform generator, it can be modified via

an on-screen editor and then replicated out of the generator. The

MDO3000 is compatible with Tektronix’ ArbExpress PC-based waveform

creation and editing software, making creation of complex waveforms fast

and easy. Transfer waveform files to your MDO3000 edit memory via USB

or LAN or using a USB mass storage device to be output from the AFG in

the oscilloscope.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 9

Waveform type selection in the integrated AFG.

Arbitrary waveform editor showing the point-by-point editor.

Logic Analyzer (optional)

The logic analyzer (option MDO3MSO) provides 16 digital channels which

are tightly integrated into the oscilloscope's user interface. This simplifies

operation and makes it possible to solve mixed-signal issues easily.

The MDO3000 with MDO3MSO option provides 16 integrated digital channels enabling

you to view and analyze time-correlated analog and digital signals.

Color-coded digital waveform display

Color-coded digital traces display ones in green and zeros in blue. This

coloring is also used in the digital channel monitor. The monitor shows if

signals are high, low, or are transitioning so you can see channel activity at

a glance without having to clutter your display with unneeded digital

waveforms.

The multiple transition detection hardware shows you a white edge on the

display when the system detects multiple transitions. White edges indicate

that more information is available by zooming in or acquiring at faster

sampling rates. In most cases zooming in will reveal the pulse that was not

viewable with the previous settings. If the white edge is still present after

zooming in as far as possible, this indicates that increasing the sample rate

on the next acquisition will reveal higher frequency information than the

previous settings could acquire.

You can group digital waveforms and enter waveform labels by using a

USB keyboard. By simply placing digital waveforms next to each other, they

form a group.

With color-coded digital waveform display, groups are created by simply placing digital

channels together on the screen, allowing digital channels to be moved as a group.

Once a group is formed, you can position all the channels contained in that

group collectively. This greatly reduces the normal setup time associated

with positioning channels individually

MagniVu™ high-speed acquisition

The main digital acquisition mode on the MDO3000 Series will capture up

to 10 M at 500 MS/s (2 ns resolution). In addition to the main record, the

MDO3000 provides an ultra high-resolution record called MagniVu which

acquires 10,000 points at up to 8.25 GS/s (121.2 ps resolution). Both main

and MagniVu waveforms are acquired on every trigger and can be switched

between in the display at any time, running or stopped. MagniVu provides

significantly finer timing resolution than comparable oscilloscopes on the

market, instilling confidence when making critical timing measurements on

digital waveforms.

Datasheet

10 www.tektronix.com

The MagniVu high-resolution record provides 121.2 ps timing resolution, enabling you to

take critical timing measurements on your digital waveforms.

P6316 MSO probe

This unique probe design offers two eight-channel pods, simplifying the

process of connecting to the device-under-test. When connecting to square

pins, the P6316 can connect directly to 8×2 square pin headers spaced on

tenth-inch centers. When more attachment flexibility is required, you can

use the included flying lead sets and grabbers to clip onto surface mount

devices or test points. The P6316 offers outstanding electrical

characteristics applying only 8 pF of capacitive loading with 101 kΩ input

impedance.

The P6316 MSO probe offers two eight-channel pods to simplify connecting to your

device.

Serial Protocol Triggering and Analysis

(optional)

On a serial bus, a single signal often includes address, control, data, and

clock information. This can make isolating events of interest difficult.

Automatic trigger, decode, and search on bus events and conditions gives

you a robust set of tools for debugging serial buses.

Triggering on a specific address and data packet going across an I2C bus. The yellow

waveform is clock and the blue waveform is the data. A bus waveform provides decoded

packet content including Start, Address, Read/Write, Data, and Stop.

Serial triggering

Trigger on packet content such as start of packet, specific addresses,

specific data content, unique identifiers, etc. on popular serial interfaces

such as I2C, SPI, RS-232/422/485/UART, USB2.0, CAN, LIN, FlexRay,

MIL-STD-1553, and I2S/LJ/RJ/TDM.

Bus display

Provides a higher-level, combined view of the individual signals (clock,

data, chip enable, etc.) that make up your bus, making it easy to identify

where packets begin and end and identifying sub-packet components such

as address, data, identifier, CRC, etc.

Bus decoding

Tired of having to visually inspect the waveform to count clocks, determine

if each bit is a 1 or a 0, combine bits into bytes, and determine the hex

value? Let the oscilloscope do it for you! Once you’ve set up a bus, the

MDO3000 Series will decode each packet on the bus, and display the value

in hex, binary, decimal (USB, LIN, FlexRay, and MIL-STD-1553 only),

signed decimal (I2S/LJ/RJ/TDM only), or ASCII (USB, MIL-STD-1553 and

RS-232/422/485/UART only) in the bus waveform.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 11

Serial bus technologies supported by the MDO3000

Technology Trigger, Decode,

Order product

Embedded I2C Yes MDO3EMBD

SPI Yes MDO3EMBD

Computer RS232/422/485,

UART

Yes MDO3COMP

USB USB LS, FS, HS Yes (trigger on LS

and FS only; HS

decode only on

1 GHz models)

MDO3USB

Automotive CAN Yes MDO3AUTO

LIN Yes MDO3AUTO

FlexRay Yes MDO3FLEX

Military and

aerospace

MIL-STD-1553 Yes MDO3AERO

Audio I2S Yes MDO3AUDIO

LJ, RJ Yes MDO3AUDIO

TDM Yes MDO3AUDIO

Event table

In addition to seeing decoded packet data on the bus waveform itself, you

can view all captured packets in a tabular view much like you would see in

a software listing. Packets are time stamped and listed consecutively with

columns for each component (Address, Data, etc.). You can save the event

table data in .CSV format.

Event table showing decoded identifier, DLC, DATA, and CRC for every CAN packet in a

long acquisition.

Search (serial triggering)

Serial triggering is very useful for isolating the event of interest, but once

you’ve captured it and need to analyze the surrounding data, what do you

do? In the past, users had to manually scroll through the waveform

counting and converting bits and looking for what caused the event. You

can have the oscilloscope automatically search through the acquired data

for user-defined criteria including serial packet content. Each occurrence is

highlighted by a search mark. Rapid navigation between marks is as simple

as pressing the Previous (←) and Next (→) buttons on the front panel.

Digital Voltmeter (DVM) and Frequency

Counter

The MDO3000 contains an integrated 4-digit digital voltmeter (DVM) and 5-

digit frequency counter. Any of the analog inputs can be a source for the

voltmeter, using the same probes that are already attached for general

oscilloscope usage. The easy-to-read display offers you both numeric and

graphical representations of the changing measurement values. The

display also shows minimum, maximum, and average values of the

measurement as well as the range of values measured over the previous

five second interval. The DVM and frequency counter is available on any

MDO3000 and is activated when you register your product.

A DC measurement value is shown with a five second variation along with minimum,

maximum, and average voltage values. The frequency of the waveform is also shown.

Datasheet

12 www.tektronix.com

Designed to fit into your work environment

The MDO3000 is designed to fit into your work environment. With six instruments in one

small, portable package, the MDO3000 offers a unique combination of debug tools

without taking up valuable space on your bench.

Large high-resolution display

The MDO3000 Series features a 9 inch (229 mm) wide-screen, high-

resolution (800 × 480 WVGA) display for seeing intricate signal details.

Connectivity

The MDO3000 contains a number of ports which can be used to connect

the instrument to a network, directly to a PC, or other test equipment.

Front and rear USB host ports enable easy transfer of screen shots,

instrument settings, and waveform data to a USB mass storage device.

A USB keyboard can also be attached to a USB host port for data

entry.

Rear USB device port is useful for controlling the oscilloscope remotely

from a PC or for printing directly to a PictBridge®-compatible printer.

The standard 10/100 Ethernet port on the rear of the instrument

enables easy connection to networks, provides network and e-mail

printing, and provides LXI Core 2011 compatibility.

A video out port on the rear of the instrument allows the display to be

exported to an external monitor or projector.

Compact form factor

With the compact, portable form factor, you can easily move the

oscilloscope between labs. And with a depth of just 5.8 inches (147 mm), it

saves you valuable space on your test bench. The MDO3000 has all the

tools you'll need for everyday debug tasks, all in a single instrument.

The MDO3000 Series compact form factor frees up valuable space on your bench or

desktop while making sure you will always have the debug tools you need.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 13

Specifications

All specifications apply to all models unless noted otherwise.

MDO3012 MDO3014 MDO3022 MDO3024 MDO3032 MDO3034 MDO3052 MDO3054 MDO3102 MDO3104

Analog channels 2 4 2 4 2 4 2 4 2 4

Analog channel bandwidth 100 MHz 100 MHz 200 MHz 200 MHz 350 MHz 350 MHz 500 MHz 500 MHz 1 GHz 1 GHz

Rise time

(10 mV/div setting with

50Ω input termination)

4 ns 4 ns 2 ns 2 ns 1.14 ns 1.14 ns 800 ps 800 ps 400 ps 400 ps

Sample rate (1 ch) 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 5 GS/s 5 GS/s

Sample rate (2 ch) 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 2.5 GS/s 5 GS/s 5 GS/s

Sample rate (4 ch) - 2.5 GS/s - 2.5 GS/s - 2.5 GS/s - 2.5 GS/s - 2.5 GS/s

Record length (1 ch) 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M

Record length (2 ch) 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M 10 M

Record length (4 ch) - 10 M - 10 M - 10 M - 10 M - 10 M

Digital channels with

MDO3MSO option

16 16 16 16 16 16 16 16 16 16

Arbitrary Function

Generator outputs with

MDO3AFG option

1 1 1 1 1 1 1 1 1 1

Spectrum analyzer

channels

1 1 1 1 1 1 1 1 1 1

Standard spectrum

analyzer frequency range

9 kHz -

100 MHz

9 kHz -

100 MHz

9 kHz -

200 MHz

9 kHz -

200 MHz

9 kHz -

350 MHz

9 kHz -

350 MHz

9 kHz -

500 MHz

9 kHz -

500 MHz

9 kHz -

1 GHz

9 kHz -

1 GHz

Optional spectrum

analyzer frequency range

with MDO3SA option

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

9 kHz -

3 GHz

Vertical system analog channels

Hardware bandwidth limits

≥350 MHz models 20 MHz or 250 MHz

100 MHz and 200 MHz models 20 MHz

Input coupling AC, DC

Input impedance 1 MΩ ±1%, 50 Ω ±1%, 75 Ω ±1%; 75 Ω not available on 1 GHz models

Input sensitivity range

1 MΩ 1 mV/div to 10 V/div

50 Ω, 75 Ω 1 mV/div to 1 V/div

Vertical resolution 8 bits (11 bits with Hi Res)

Maximum input voltage

1 MΩ 300 VRMS CAT II with peaks ≤ ±425 V

50 Ω, 75 Ω 5 VRMS with peaks ≤ ±20 V

Datasheet

14 www.tektronix.com

DC gain accuracy ±1.5% for 5 mV/div and above, derated at 0.10%/°C above 30 °C

±2.0% for 2 mV/div, derated at 0.10%/°C above 30 °C

±2.5% for 1 mV/div, derated at 0.10%/°C above 30 °C

±3.0% for variable gain, derated 0.10%/°C above 30 °C

Channel-to-channel isolation Any two channels at equal vertical scale ≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to the rated bandwidth

Offset range Volts/div setting Offset range

1 M Ω input 50 Ω, 75 Ω input

1 mV/div to 50 mV/div ±1 V ±1 V

50.5 mV/div to 99.5 mV/div ±0.5 V ±0.5 V

100 mV/div to 500 mV/div ±10 V ±10 V

505 mV/div to 995 mV/div ±5 V ±5 V

1 V/div to 5 V/div ±100 V ±5 V

Vertical system digital channels

(Requires MDO3MSO option)

Input channels 16 digital (D15 to D0)

Thresholds Threshold per set of 8 channels

Threshold selections TTL, CMOS, ECL, PECL, User-defined

User-defined threshold range -15 V to +25 V

Maximum input voltage -20 V to +30 V

Threshold accuracy ±[100 mV + 3% of threshold setting]

Input dynamic range 50 Vp-p (threshold setting dependent)

Minimum voltage swing 500 mV

Input resistance 101 kΩ

Probe loading 8 pF

Vertical resolution 1 bit

Mixed Domain Osciloscopes -- MDO3000 Series

Vertical system analog channels

www.tektronix.com 15

Horizontal system analog channels

Time base range

1 GHz models 400 ps/div to 1000 s/div

≤ 500 MHz models 1 ns/div to 1000 s/div

Maximum duration at highest

sample rate (all/half channels)

1 GHz models 4/2 ms

≤ 500 MHz models 4/4 ms

Time-base delay time range -10 divisions to 5000 s

Channel-to-channel deskew range ±125 ns

Time base accuracy ±10 ppm over any ≥1 ms interval

Horizontal system digital channels

(Requires MDO3MSO option)

Maximum sample rate (Main) 500 MS/s (2 ns resolution)

Maximum record length (Main) 10 M

Maximum sample rate (MagniVu) 8.25 GS/s (121.2 ps resolution)

Maximum record length (MagniVu 10k centered on the trigger

Minimum detectable pulse width

(typical)

2 ns

Channel-to-channel skew (typical) 500 ps

Maximum input toggle rate 250 MHz (Maximum frequency sine wave that can accurately be reproduced as a logic square wave. Requires the use of a short

ground extender on each channel. This is the maximum frequency at the minimum swing amplitude. Higher toggle rates can be

achieved with higher amplitudes.)

Spectrum analyzer input

Capture bandwidth MDO3012, MDO3014 models: 100 MHz

MDO3022, MDO3024 models: 200 MHz

MDO3032, MDO3034 models: 350 MHz

MDO3052, MDO3054 models: 500 MHz

MDO3102, MDO3104 models: 1 GHz

All models: 3 GHz with option MDO3SA

Span MDO3012, MDO3014 models: 9 kHz – 100 MHz

MDO3022, MDO3024 models: 9 kHz – 200 MHz

MDO3032, MDO3034 models: 9 kHz – 350 MHz

MDO3052, MDO3054 models: 9 kHz – 500 MHz

MDO3102, MDO3104 models: 9 kHz – 1 GHz

All models: 9 kHz – 3 GHz with option MDO3SA, in a 1-2-5 sequence

Datasheet

16 www.tektronix.com

Resolution bandwidth 20 Hz - 150 MHz in a 1-2-3-5 sequence

Reference level -130 dBm to +20 dBm in steps of 5 dBm

Vertical scale 1 dB/div to 20 dB/div in a 1-2-5 sequence

Vertical position -100 divs to +100 divs (displayed in dB)

Vertical units dBm, dBmV, dBµV, dBµW, dBmA, dBµA

Displayed average noise level

(DANL)

9 kHz - 50 kHz < -109 dBm/Hz (< -113 dBm/Hz typical)

50 kHz – 5 MHz < -126 dBm/Hz (< -130 dBm/Hz typical)

5 MHz - 2 GHz < -138 dBm/Hz (< -142 dBm/Hz typical)

2 GHz – 3 GHz < -128 dBm/Hz (< -132 dBm/Hz typical)

DANL with TPA-N-PRE preamp

attached

Preamp set to "Auto", and Reference Level set to -40 dB

9 kHz - 50 kHz < -117 dBm/Hz (< -121 dBm/Hz typical)

50 kHz – 5 MHz < -136 dBm/Hz (< -140 dBm/Hz typical)

5 MHz - 2 GHz < -148 dBm/Hz (< -152 dBm/Hz typical)

2 GHz – 3 GHz < -138 dBm/Hz (< -142 dBm/Hz typical)

Spurious response

2nd harmonic distortion

(>100 MHz)

< -55 dBc (< -60 dBc typical)

3rd harmonic distortion

(>100MHz)

< -53 dBc (< -58 dBc typical)

2nd order intermodulation

distortion (>15 MHz)

< -55 dBc (< -60 dBc typical)

3rd order intermodulation

distortion (>15 MHz)

< -55 dBc (< -60 dBc typical)

Residual response < -78 dBm (≤ -15 dBm reference level and RF input terminated with 50Ω)

At 2.5 GHz <-67 dBm

At 1.25 GHz <-76 dBm

Crosstalk to spectrum analyzer

from oscilloscope channels

≤800 MHz input frequencies < -60 dB from ref level (typical)

>800 MHz - 2 GHz input

frequencies

< -40 dB from ref level (typical)

Phase noise at 1 GHz CW

10 kHz < -81 dBc/Hz, < -85 dBc/Hz (typical)

100 kHz < -97 dBc/Hz, < -101 dBc/Hz (typical)

1 MHz < -118 dBc/Hz, < -122 dBc/Hz (typical)

Mixed Domain Osciloscopes -- MDO3000 Series

Spectrum analyzer input

www.tektronix.com 17

Level measurement uncertainty Reference level 10 dBm to -15 dBm. Input level ranging from reference level to 40 dB below reference level. Specifications

exclude mismatch error.

18 °C - 28 °C < ±1.2 dBm (< ±0.6 dBm typical)

Over operating range < ±2.0 dBm

Level measurement uncertainty

with TPA-N-PRE preamp attached

Preamp mode set to “Auto”. Reference level 10 dBm set to -40dBm. Input level ranging from reference level to 30 dB below

reference level. Specifications exclude mismatch error.

18 °C - 28 °C < ±1.5 dBm (typical) either preamp state

Over operating range < ±2.3 dBm either preamp state

Frequency measurement accuracy ±(([Reference Frequency Error] x [Marker Frequency]) + (span/750 + 2)) Hz; Reference Frequency Error = 10ppm (10 Hz / MHz)

Maximum operating input level

Average continuous power +20 dBm (0.1 W)

DC maximum before damage ±40 V DC

Maximum power before

damage (CW)

+33 dBm (2 W)

Maximum power before

damage (pulse)

+45 dBm (32 W) (<10 µs pulse width, <1% duty cycle, and reference level of ≥ +10 dBm)

Maximum operating input level

with TPA-N-PRE preamp attached

Average continuous power +20 dBm (0.1 W)

DC maximum before damage ±20 V DC

Maximum power before

damage (CW)

+30 dBm (1 W)

Maximum power before

damage (pulse)

+45 dBm (32 W) (<10 μs pulse width, <1% duty cycle, and reference level of ≥ +10 dBm)

Frequency domain trace types Normal, Average, Max Hold, Min Hold

Detection methods +Peak, -Peak, Average, Sample

Automatic markers One to eleven peaks identified based on user-adjustable threshold and excursion values

Manual markers Two manual markers indicating frequency, amplitude, noise density, and phase noise

Marker readouts Absolute or Delta

FFT windows FFT window Factor

Kaiser 2.23

Rectangular 0.89

Hamming 1.30

Hanning 1.44

Blackman-Harris 1.90

Flat-Top 3.77

Datasheet

Spectrum analyzer input

18 www.tektronix.com

Trigger system

Trigger modes Auto, Normal, and Single

Trigger coupling DC, AC, HF reject (attenuates >50 kHz), LF reject (attenuates <50 kHz), noise reject (reduces sensitivity)

Trigger holdoff range 20 ns to 8 s

Trigger sensitivity (typical) Edge type, DC coupled

Trigger source Sensitivity

Any analog channel input For 1 mV/div to 4.98 mV/div; 0.75 div from DC to 50 MHz,

increasing to 1.3 div at instrument bandwidth

≥ 5mV/div: 0.40 div from DC to 50 MHz

Aux In (External); available on two-channel instruments only 200 mV from DC to 50 MHz, increasing to 500 mV at 200 M

Line Fixed

Trigger level ranges

Any input channel ±8 divisions from center of screen, ±8 divisions from 0 V when vertical LF reject trigger coupling is selected

Aux In (External) ±8 V

Line The line trigger level is fixed at about 50% of the line voltage.

Trigger frequency readout Provides 6-digit frequency readout of triggerable events.

Trigger types

Edge Positive, negative, or either slope on any channel. Coupling includes DC, AC, HF reject, LF reject, and noise reject.

Sequence (B-trigger) Trigger Delay by Time: 8 ns to 8 s. Or Trigger Delay by Events: 1 to 4,000,000 events. Not available when “Either” edge is

selected.

Pulse Width Trigger on width of positive or negative pulses that are >, <, =, ≠, or inside/outside a specified period of time.

Timeout Trigger on an event which remains high, low, or either, for a specified time period (4 ns to 8 s).

Runt Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.

Logic Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock

to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for all input channels defined as High, Low, or

Don’t Care.

Setup and Hold Trigger on violations of both setup time and hold time between clock and data present on any of the analog and digital input

channels.

Setup and hold trigger type Description

Setup Time Range -0.5 ns to 1.024 ms

Hold Time Range 1.0 ns to 1.024 ms

Setup + Hold Time Range 0.5 ns to 2.048 ms

Rise/Fall Time Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either and time range is

4.0 ns to 8 s.

Video Trigger on all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals.

480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30,

1080p/50, 1080p/60

Custom bi-level and tri-level sync video standards.

I2C (optional) Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I2C buses up to 10 Mb/s.

SPI (optional) Trigger on SS active, Start of Frame, MOSI, MISO, or MOSI and MISO on SPI buses up to 50.0 Mb/s.

RS-232/422/485/UART

(optional)

Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error up

to 10 Mb/s.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 19

USB: Low speed (optional) Trigger on Sync Active, Start of Frame, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet,

Handshake Packet, Special Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP

token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame

number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data

value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL.

Special packet trigger - Any special type, Reserved

Error trigger - PID Check, CRC5 or CRC16, Bit Stuffing.

USB: Full speed (optional) Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special

Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP

token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame

number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data

value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL.

Special packet trigger - Any special type, PRE, Reserved.

Error trigger - PID Check, CRC5 or CRC16, Bit Stuffing.

CAN (optional) Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data,

End of Frame, Missing ACK, or Bit Stuffing Error on CAN signals up to 1 Mb/s.

Data can be further specified to trigger on ≤, <, =, >, ≥, or ≠ a specific data value. User-adjustable sample point is set to 50% by

default.

LIN (optional) Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, Errors such as Sync, Parity, or Checksum

Errors up to 100 kb/s (by LIN definition, 20 kb/s).

FlexRay (optional) Trigger on Start of Frame, Type of Frame (Normal, Payload, Null, Sync, Startup), Identifier, Cycle Count, Complete Header Field,

Data, Identifier and Data, End of Frame or Errors such as Header CRC, Trailer CRC, Null Frame, Sync Frame, or Startup Frame

Errors up to 100 Mb/s.

MIL-STD-1553 (optional) Trigger on Sync, Word Type 1 (Command, Status, Data), Command Word (set RT Address, T/R, Sub-address/Mode, Data Word

Count/Mode Code, and Parity individually), Status Word (set RT Address, Message Error, Instrumentation, Service Request Bit,

Broadcast Command Received, Busy, Subsystem Flag, Dynamic Bus Control Acceptance (DBCA), Terminal Flag, and Parity

individually), Data Word (user-specified 16-bit data value), Error (Sync, Parity, Manchester, Non-contiguous data), Idle Time

(minimum time selectable from 2 µs to 100 µs; maximum time selectable from 2 µs to 100 µs; trigger on < minimum, > maximum,

inside range, outside range).

RT Address can be further specified to trigger on =, ≠, <, >, ≤, ≥ a particular value, or inside or outside of a range.

I2S/LJ/RJ/TDM (optional) Trigger on Word Select, Frame Sync, or Data. Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value, or

inside or outside of a range. Maximum data rate for I2S/LJ/RJ is 12.5 Mb/s. Maximum data rate for TDM is 25 Mb/s.

Parallel (available when

option MDO3MSO is installed)

Trigger on a parallel bus data value. Parallel bus can be from 1 to 20 bits (from the digital and analog channels) in size. Binary and

Hex radices are supported.

1Trigger selection of Command Word will trigger on Command and ambiguous Command/Status words. Trigger selection of Status Word will trigger on Status and ambiguous Command/Status words.

Datasheet

Trigger system

20 www.tektronix.com

Acquisition system

Acquisition modes

Sample Acquire sampled values.

Peak Detect Captures glitches as narrow as 1.5 ns (1 GHz models), 2.0 ns (500 MHz models), 3.0 ns (350 MHz models), 5.0 ns (200 MHz

models), 7.0 ns (100 MHz models) at all sweep speeds

Averaging From 2 to 512 waveforms included in average.

Envelope Min-max envelope reflecting Peak Detect data over multiple acquisitions. Number of waveforms in the envelope selectable

between 1 and 2000 and infinity

Hi Res Real-time boxcar averaging reduces random noise and increases vertical resolution.

Roll Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40 ms/div.

FastAcq™FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events, capturing >280,000 wfms/s on

1 GHz models and >235,000 wfms/s on 100 MHz – 500 MHz models.

Waveform measurements

Cursors Waveform and Screen

Automatic measurements

(time domain)

30, of which up to four can be displayed on-screen at any one time. Measurements include: Period, Frequency, Delay, Rise Time,

Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive

Overshoot, Negative Overshoot, Total Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle

RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area and Cycle Area.

Automatic Measurements

(frequency domain)

3, of which one can be displayed on-screen at any one time. Measurements include Channel Power, Adjacent Channel Power

Ratio (ACPR), and Occupied Bandwidth (OBW)

Measurement statistics Mean, Min, Max, Standard Deviation.

Reference levels User-definable reference levels for automatic measurements can be specified in either percent or units.

Gating Isolate the specific occurrence within an acquisition to take measurements on, using either the screen or waveform cursors.

Waveform histogram A waveform histogram provides an array of data values representing the total number of hits inside of a user-defined region of the

display. A waveform histogram is both a visual graph of the hit distribution as well as a numeric array of values that can be

measured.

Sources Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math

Types Vertical, Horizontal

Waveform histogram

measurements

12, of which up to four can be displayed on-screen at any one time. Waveform Count, Hits in Box, Peak Hits, Median, Max, Min,

Peak-to-Peak, Mean, Standard Deviation, Sigma 1, Sigma 2, Sigma 3

Waveform math

Arithmetic Add, subtract, multiply, and divide waveforms.

Math functions Integrate, differentiate, FFT

FFT Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning, or

Blackman-Harris.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 21

Spectrum math Add or subtract frequency-domain traces.

Advanced Math Define extensive algebraic expressions including waveforms, reference waveforms, math functions (FFT, Intg, Diff, Log, Exp, Sqrt,

Abs, Sine, Cosine, Tangent, Rad, Deg), scalars, up to two user-adjustable variables and results of parametric measurements

(Period, Freq, Delay, Rise, Fall, PosWidth, NegWidth, BurstWidth, Phase, PosDutyCycle, NegDutyCycle, PosOverShoot,

NegOverShoot, TotalOverShoot, PeakPeak, Amplitude, RMS, CycleRMS, High, Low, Max, Min, Mean, CycleMean, Area,

CycleArea, and trend plots). for example, (Intg(Ch1 - Mean(Ch1)) × 1.414 × VAR1)

Act on Event

Events None, when a trigger occurs, or when a defined number of acquisitions complete (1 to 1,000,000)

Actions Stop acquisition, save waveform to file, save screen image, print, AUX OUT Pulse, remote interface SRQ, e-mail notification, and

visual notification

Repeat Repeat the act on event process (1 to 1,000,000 and infinity)

Video Picture mode

Sources Channel 1, Channel 2, Channel 3, Channel 4

Video standards NTSC, PAL

Contrast and brightness Manual and automatic

Field selection Odd, Even, Interlaced

Picture location on screen Selectable X and Y location, width and height adjustment, start line and pixel and line-to-line offset control.

Power measurements (optional)

Power quality measurements VRMS, VCrest Factor, Frequency, IRMS, ICrest Factor, True Power, Apparent Power, Reactive Power, Power Factor, Phase Angle.

Switching loss measurements

Power loss Ton, Toff, Conduction, Total.

Energy loss Ton, Toff, Conduction, Total.

Harmonics THD-F, THD-R, RMS measurements. Graphical and table displays of harmonics. Test to IEC61000-3-2 Class A and MIL-

STD-1399, Section 300A.

Ripple measurements VRipple and IRipple.

Modulation analysis Graphical display of +Pulse Width, -Pulse Width, Period, Frequency, +Duty Cycle, and -Duty Cycle modulation types.

Safe operating area Graphical display and mask testing of switching device safe operating area measurements.

dV/dt and dI/dt measurements Cursor measurements of slew rate

Datasheet

Waveform math

22 www.tektronix.com

Limit/Mask testing (optional)

Test source Limit test: Any Ch1 - Ch4 or any R1 - R4

Mask test: Any Ch1 - Ch4

Mask creation Limit test vertical tolerance from 0 to 1 division in 1 m division increments; Limit test horizontal tolerance from 0 to 500 m division in

1 m division increments.

Load custom mask from text file with up to 8 segments.

Mask scaling Lock to Source ON (mask automatically re-scales with source-channel settings changes)

Lock to Source OFF (mask does not re-scale with source-channel settings changes)

Test criteria run until Minimum number of waveforms (from 1 to 1,000,000 and Infinity)

Minimum elapsed time (from 1 second to 48 hours and Infinity)

Violation threshold From 1 to 1,000,000 and Infinity

Actions on test failure Stop acquisition, save screen image to file, save waveform to file, print screen image, AUX OUT pulse, set remote interface SRQ

Actions on test complete AUX OUT pulse, set remote interface SRQ

Results display Test status, total waveforms, number of violations, total tests, failed tests, elapsed time, total hits for each mask segment

Arbitrary Function Generator

(Requires MDO3AFG option)

Waveforms Sine, Square, Pulse, Ramp/Triangle, DC, Noise, Sin(x)/x (Sinc), Gaussian, Lorentz, Exponential Rise, Exponential Decay,

Haversine, Cardiac, and Arbitrary.

Sine

Frequency range 0.1 Hz to 50 MHz

Amplitude range 20 mVp-p to 5 Vp-p into Hi-Z; 10 mVp-p to 2.5 Vp-p into 50 Ω

Amplitude flatness ±0.5 dB typical at 1 kHz (±1.5 dB for <20 mVp-p amplitudes)

Total harmonic distortion

(typical)

1% into 50Ω

2% for amplitude < 50 mV and frequencies > 10 MHz

3% for amplitude < 20 mV and frequencies > 10 MHz

Spurious free dynamic range

(SFDR)

-40 dBc (Vp-p ≥ 0.1 V); -30dBc (Vp-p ≤ 0.1 V), 50 Ω load

Square / Pulse

Frequency range 0.1 Hz to 25 MHz

Amplitude range 20 mVp-p to 5 Vp-p into Hi-Z; 10 mVp-p to 2.5 Vp-p into 50 Ω

Duty cycle 10% to 90% or 10 ns minimum pulse, whichever is larger cycle

Duty cycle resolution 0.1%

Pulse width minimum 10 ns typical

Rise/fall time 5 ns typical (10% - 90%)

Pulse width resolution 100 ps

Overshoot < 2% typical for signal steps greater than 100 mV

Asymmetry ±1% ±5 ns, at 50% duty cycle

Jitter (TIE RMS) < 500 ps typical

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 23

Ramp / Triangle

Frequency range 0.1 Hz to 500 kHz

Amplitude range 20 mVp-p to 5 Vp-p into Hi-Z; 10 mVp-p to 2.5 Vp-p into 50 Ω

Variable symmetry 0% to 100%

Symmetry resolution 0.1%

Level range ±2.5 V into Hi-Z; ±1.25 V into 50 Ω

Noise

Amplitude range 20 mVp-p to 5 Vp-p in to Hi-Z; 10 mVp-p to 2.5 Vp-p into 50 Ω

Amplitude resolution 0% to 100% in 1% increments

Sin(x)/x (Sinc)

Frequency range 0.1 Hz to 2 MHz

Amplitude range 20 mVp-p to 3.0 Vp-p into Hi-Z; 10 mVp-p to 1.5 Vp-p into 50 Ω

Gaussian

Frequency range 0.1 Hz to 5 MHz

Amplitude range 20 mVp-p to 2.5 Vp-p into Hi-Z; 10 mVp-p to 1.25 Vp-p into 50 Ω

Lorentz

Frequency range 0.1 Hz to 5 MHz

Amplitude range 20 mVp-p to 2.4 Vp-p into Hi-Z; 10 mVp-p to 1.2 Vp-p into 50 Ω

Exponential Rise / Decay

Frequency range 0.1 Hz to 5 MHz

Amplitude range 20 mVp-p to 2.5 Vp-p into Hi-Z; 10 mVp-p to 1.25 Vp-p into 50 Ω

Haversine

Frequency range 0.1 Hz to 5 MHz

Amplitude range 20 mVp-p to 2.5 Vp-p into Hi-Z; 10 mVp-p to 1.25 Vp-p into 50 Ω

Cardiac

Frequency range 0.1 Hz to 500 kHz

Amplitude range 20 mVp-p to 5 Vp-p into Hi-Z; 10 mVp-p to 2.5 Vp-p into 50 Ω

Arbitrary

Memory depth 1 to 128 k

Amplitude range 20 mVp-p to 5 Vp-p into Hi-Z; 10 mVp-p to 2.5 Vp-p into 50 Ω

Repetition rate 0.1 Hz to 25 MHz

Sample rate 250 MS/s

Frequency accuracy

Sine wave and ramp 130 ppm (frequency < 10 kHz)

50 ppm (frequency ≥ 10 kHz)

Square wave and pulse 130 ppm (frequency < 10 kHz)

50 ppm (frequency ≥ 10 kHz)

Resolution 0.1 Hz or 4 digits; whichever is larger

Datasheet

Arbitrary Function Generator

24 www.tektronix.com

Amplitude accuracy ±[ (1.5% of peak-to-peak amplitude setting) + (1.5% of DC offset setting) + 1 mV ] (frequency = 1 kHz)

DC offset

DC offset range ±[2.5 V – (signal amplitude) / 2 ] into Hi-Z; ±[1.25 – (signal amplitude) / 2 ] into 50 Ω

DC offset resolution 1 mV into Hi-Z; 500 uV into 50 Ω

Offset accuracy ±[(1.5% of absolute offset voltage setting) + 1 mV]; derated 3 mV for every 10 °C away from 25 °C

ArbExpress®The MDO3000 is compatible with ArbExpress® PC-based signal generator waveform creation and editing software. Capture

waveforms on the MDO3000 oscilloscope and transfer them to ArbExpress for editing. Create complex waveforms in ArbExpress

and transfer them to the arbitrary function generator in the MDO3000 for output. To download ArbExpress software, go to

www.tektronix.com/downloads.

Digital voltmeter (DVM) and frequency counter

Source Channel 1, Channel 2, Channel 3, Channel 4

Measurement types AC RMS, DC, AC+DC RMS (reads out in volts or amps); Frequency

Resolution ACV, DCV: 4 digits

Frequency: 5 digits

Frequency accuracy 10 ppm

Measuring rate 100 times/second; measurements updated on the display 4 times/second

Vertical settings autorange Automatic adjustment of vertical settings to maximize measurement dynamic range; available for any non-trigger source

Graphical measurement Graphical indication of minimum, maximum, current value, and five second rolling range

Software

OpenChoice® Desktop Enables fast and easy communication between a Windows PC and your oscilloscope using USB or LAN. Transfer and save

settings, waveforms, measurements, and screen images. Word and Excel toolbars automate the transfer of acquisition data and

screen images from the oscilloscope into Word and Excel for quick reporting or further analysis.

IVI driver Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI,

MicrosoftNET, and MATLAB.

e*Scope® Web-based interface Enables control of the oscilloscope over a network connection through a standard web browser. Simply enter the IP address or

network name of the oscilloscope and a web page will be served to the browser. Transfer and save settings, waveforms,

measurements, and screen images or make live control changes to settings on the oscilloscope directly from the web browser.

LXI Core 2011 Web interface Connect to the oscilloscope through a standard Web browser by simply entering the oscilloscope IP address or network name in

the address bar of the browser. The Web interface enables viewing of instrument status and configuration, status and modification

of network settings, and instrument control through e*Scope Web-based remote control. All Web interaction conforms to LXI Core

2011 specification, version 1.4.

Mixed Domain Osciloscopes -- MDO3000 Series

Arbitrary Function Generator

www.tektronix.com 25

Display system

Display type 9 in. (229 mm) color display

Display resolution 800 horizontal × 480 vertical pixels (WVGA)

Interpolation Sin(x)/x

Waveform styles Vectors, Dots, Variable Persistence, Infinite Persistence

FastAcq. palettes Temperature, Spectral, Normal, Inverted

Graticules Full, Grid, Solid, Cross Hair, Frame, IRE and mV

Format YT, XY, and simultaneous XY/YT

Maximum waveform capture rate >280,000 wfms/s in FastAcq acquisition mode for 1 GHz models

>235,000 wfms/s in FastAcq acquisition mode for 100 MHz – 500 MHz models

>50,000 wfms/s in DPO acquisition mode on all models

Input/output ports

USB 2.0 high-speed host port Supports USB mass storage devices, printers and keyboard. One port on front and one port on rear of instrument.

USB 2.0 device port Rear-panel connector allows for communication/control of oscilloscope through USBTMC or GPIB (with a TEK-USB-488), and

direct printing to PictBridge-compatible printers.

Printing Print to network printer, PictBridge printer, or to a printer that supports e-mail printing. Note: This product includes software

developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)

LAN port RJ-45 connector, supports 10/100 Mb/s

Video out port DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector. XGA resolution.

Auxilliary input (Available on two-channel models only)

Front-panel BNC connector Input impedance, 1 MΩ

Maximum input 300 VRMS CAT II with peaks ≤ ±425 V

Probe compenstor output voltage

and frequency

Front-panel pins

Amplitude 0 to 2.5 V

Frequency 1 kHz

Auxiliary out Rear-panel BNC connector

VOUT (Hi): ≥2.25 V open circuit, ≥0.9 V 50 Ω to ground

VOUT (Lo): ≤0.7 V into a load of ≤4 mA; ≤0.25 V 50 Ω to ground

Output can be configured to provide a pulse out signal when the oscilloscope triggers, a trigger signal from the internal arbitrary

function generator, or an event out for limit/mask testing.

Kensington-style lock Rear-panel security slot connects to standard Kensington-style lock.

VESA mount Standard (MIS-D 75) 75 mm VESA mounting points on rear of instrument.

Datasheet

26 www.tektronix.com

LAN eXtensions for Instrumentation (LXI)

Class LXI Core 2011

Version V1.4

Power source

Power source voltage 100 to 240 V ±10%

Power source frequency 50 to 60 Hz at 100 to 240 V

400 Hz ±10% at 115 V

Power consumption 120 W maximum

Physical characteristics

Dimensions

Height 203.2 mm (8 in.)

Width 416.6 mm (16.4 in.)

Depth 147.4 mm (5.8 in.)

Weight

Net 4.2 kg (9.2 lb.)

Shipping 8.6 kg (19 lb.)

Rackmount configuration 5U

Cooling clearance 2 in. (51 mm) required on left side and rear of instrument

EMC, environment, and safety

Temperature

Operating -10 ºC to +55 ºC (+14 ºF to 131 ºF)

Nonoperating -40 ºC to +71 ºC (-40 ºF to 160 ºF)

Humidity

Operating Up to +40 ºC, 5% to 90% relative humidity

+40 ºC to +55 ºC, 5% to 60% relative humidity

Nonoperating Up to +40 ºC, 5% to 90% relative humidity

Above +40 ºC up to +55 ºC, 5% to 60% relative humidity

Above +55 ºC up to +71 ºC, 5% to 40% relative humidity, non-condensing

Altitude

Operating 3,000 meters (9,843 feet)

Nonoperating 12,000 meters (39,370 feet)

Regulatory

Electromagnetic compatibility EC Council Directive 2004/108/EC

Safety UL61010-1:2004, CAN/CSA-C22.2 No. 61010.1: 2004, Low Voltage Directive 2006/95/EC and EN61010-1:2001, IEC

61010-1:2001, ANSI 61010-1-2004, ISA 82.02.01

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 27

Ordering information

Step 1: Choose the MDO3000 base model

MDO3000 family

MDO3012 Mixed Domain Oscilloscope with (2) 100 MHz analog channels, and (1) 100 MHz spectrum analyzer input

MDO3014 Mixed Domain Oscilloscope with (4) 100 MHz analog channels, and (1) 100 MHz spectrum analyzer input

MDO3022 Mixed Domain Oscilloscope with (2) 200 MHz analog channels, and (1) 200 MHz spectrum analyzer input

MDO3024 Mixed Domain Oscilloscope with (4) 200 MHz analog channels, and (1) 200 MHz spectrum analyzer input

MDO3032 Mixed Domain Oscilloscope with (2) 350 MHz analog channels, and (1) 350 MHz spectrum analyzer input

MDO3034 Mixed Domain Oscilloscope with (4) 350 MHz analog channels, and (1) 350 MHz spectrum analyzer input

MDO3052 Mixed Domain Oscilloscope with (2) 500 MHz analog channels, and (1) 500 MHz spectrum analyzer input

MDO3054 Mixed Domain Oscilloscope with (4) 500 MHz analog channels, and (1) 500 MHz spectrum analyzer input

MDO3102 Mixed Domain Oscilloscope with (2) 1 GHz analog channels, and (1) 1 GHz spectrum analyzer input

MDO3104 Mixed Domain Oscilloscope with (4) 1 GHz analog channels, and (1) 1 GHz spectrum analyzer input

Standard accessories

Probes

100 MHz, 200 MHz models TPP0250, 250 MHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel

350 MHz, 500 MHz models TPP0500B, 500 MHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel

1 GHz models TPP1000, 1 GHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel

Any model with MDO3MSO option One P6316 16-channel logic probe and accessories

Accessories

103-0473-00 N-to-BNC adapter

063-4526-xx Documentation CD

071-3249-00 Installation and Safety Instructions, printed manual (translated in English, Japanese, and Simplified Chinese)

016-2008-xx Accessory bag

-Power cord

-OpenChoice® Desktop Software (available on the Documentation CD and for download from www.tektronix.com/downloads.)

-Calibration certificate documenting traceability to National Metrology Institute(s) and ISO9001 quality system registration

Datasheet

28 www.tektronix.com

Warranty

Three-year warranty covering all parts and labor, excluding probes.

Step 2: Configure your MDO3000 by adding instrument options

Instrument options

All MDO3000 Series instruments can be preconfigured from the factory with the following options:

MDO3AFG Arbitrary function generator with 13 predefined waveforms and arbitrary waveform generation

MDO3MSO 16 digital channels; includes P6316 digital probe and accessories

MDO3SA Increase spectrum analyzer input frequency range to 9 kHz – 3 GHz and capture bandwidth to 3 GHz.

MDO3SEC Enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument firmware

update functionality.

Power cord and plug options

Opt. A0 North America power plug (115 V, 60 Hz)

Opt. A1 Universal Euro power plug (220 V, 50 Hz)

Opt. A2 United Kingdom power plug (240 V, 50 Hz)

Opt. A3 Australia power plug (240 V, 50 Hz)

Opt. A5 Switzerland power plug (220 V, 50 Hz)

Opt. A6 Japan power plug (100 V, 110/120 V, 60 Hz)

Opt. A10 China power plug (50 Hz)

Opt. A11 India power plug (50 Hz)

Opt. A12 Brazil power plug (60 Hz)

Opt. A99 No power cord

Language options

All products are shipped with an Installation and Safety manual that is in English, Japanese, and Simplified Chinese. Full user manuals translated in each language listed

below are included with each product in pdf format on the Documentation CD.

Opt. L0 English front panel label

Opt. L1 French front panel overlay

Opt. L2 Italian front panel overlay

Opt. L3 German front panel overlay

Opt. L4 Spanish front panel overlay

Opt. L5 Japanese front panel overlay

Opt. L6 Portuguese front panel overlay

Opt. L7 Simplified Chinese front panel overlay

Opt. L8 Traditional Chinese front panel overlay

Opt. L9 Korean front panel overlay

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 29

Opt. L10 Russian front panel overlay

Opt. L99 No manual, English front panel label

Service options

Opt. C3 Calibration Service 3 Years

Opt. C5 Calibration Service 5 Years

Opt. D1 Calibration Data Report

Opt. D3 Calibration Data Report 3 Years (with Opt. C3)

Opt. D5 Calibration Data Report 5 Years (with Opt. C5)

Opt. G3 Complete Care 3 Years (includes loaner, scheduled calibration, and more)

Opt. G5 Complete Care 5 Years (includes loaner, scheduled calibration, and more)

Opt. R5 Repair Service 5 Years (including warranty)

Probes and accessories are not covered by the oscilloscope warranty and service offerings. Refer to the datasheet of each probe and accessory model for its unique warranty

and calibration terms.

Step 3: Select application models and accessories

Application modules Application modules are purchased as stand-alone products and can be purchased at the time of initial MDO3000 purchase or at

any future time.

Application modules have licenses which can be transferred between an application module and an oscilloscope. The license may

be contained in the module; allowing the module to be moved from one instrument to another. Or, the license can be contained in

the oscilloscope; allowing the module to be removed and stored for safekeeping. The license can be transferred back to the

module for use in another MDO3000 oscilloscope. Transferring the license to an oscilloscope and removing the module permits

the use of more than two applications simultaneously.

MDO3AERO Aerospace Serial Triggering and Analysis Module. Enables triggering on packet-level information on MIL-STD-1553 buses as well

as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with

time- stamp information.

Signal Inputs - Any Ch1 - Ch4, Math, Ref1 - Ref4

Recommended Probing - Differential or single ended (only one single-ended signal required)

MDO3AUDIO Audio Serial Triggering and Analysis Module. Enables triggering on packet-level information on I2S, LJ, RJ, and TDM audio buses

as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables

with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, any D0 - D15

Recommended Probing - Single ended

MDO3AUTO Automotive Serial Triggering and Analysis Module. Enables triggering on packet-level information on CAN and LIN buses as well

as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with

time- stamp information.

Signal Inputs – CAN or LIN: Any Ch1 - Ch4, any D0 - D15

Recommended Probing - CAN: Single ended or differential; LIN: Single ended

MDO3COMP Computer Serial Triggering and Analysis Module. Enables triggering on packet-level information on RS-232/422/485/UART buses

as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables

with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, any D0 - D15

Recommended Probing - RS-232/UART: Single ended; RS-422/485: Differential

Datasheet

30 www.tektronix.com

MDO3EMBD Embedded Serial Triggering and Analysis Module. Enables triggering on packet-level information on I2C and SPI buses as well as

analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-

stamp information.

Signal Inputs - I2C or SPI: Any Ch1 - Ch4, any D0 - D15

Recommended Probing - Single ended

MDO3FLEX FlexRay Serial Triggering and Analysis Module. Enables triggering on packet-level information on FlexRay buses as well as

analytical tools such as digital views of the signal, bus views, packet decoding, search tools, packet decode tables with time-stamp

information.

Signal Inputs - Any Ch1 - Ch4 (and any D0 - D15 when MDO3MSO option is installed; single-ended probing only)

Recommended Probing - Single ended or differential

MDO3USB USB Serial Triggering and Analysis Module. Enables triggering on packet-level content for low-speed, and full-speed USB serial

buses. Also enables analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet

decode tables with time-stamp information for low-speed, full-speed, and high-speed USB serial buses.

Signal Inputs - Low-speed and Full-speed: Any Ch1 - Ch4, any D0 - D15; Low-speed, Full-speed, and High-speed: Any Ch1 - Ch4,

Math, Ref1 - Ref4

Note: High-speed decode support only available on 1 GHz models.

Recommended Probing - Low-speed and Full-speed: Single ended or differential; High-speed: Differential

MDO3PWR Power Analysis Application Module. Enables quick and accurate analysis of power quality, switching loss, harmonics, safe

operating area (SOA), modulation, ripple, and slew rate (dI/dt, dV/dt).

MDO3LMT Limit and Mask Testing Application Module. Enables testing against limit templates generated from "golden" waveforms and mask

testing using custom masks.

Recommended accessories

Probes

Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please visit www.tektronix.com/probes.

TPP0250 250 MHz, 10X TekVPI® passive voltage probe with 3.9 pF input capacitance

TPP0500B 500 MHz, 10X TekVPI® passive voltage probe with 3.9 pF input capacitance

TPP0502 500 MHz, 2X TekVPI® passive voltage probe with 12.7 pF input capacitance

TPP0850 2.5 kV, 800 MHz, 50X TekVPI® passive high-voltage probe

TPP1000 1 GHz, 10X TekVPI® passive voltage probe with 3.9 pF input capacitance

TAP1500 1.5 GHz TekVPI® active single-ended voltage probe

TAP2500 2.5 GHz TekVPI® active single-ended voltage probe

TAP3500 3.5 GHz TekVPI® active single-ended voltage probe

TCP0020 50 MHz TekVPI® 20 Ampere AC/DC current probe

TCP0030A 120 MHz TekVPI® 30 Ampere AC/DC current probe

TCP0150 20 MHz TekVPI® 150 Ampere AC/DC current probe

TDP0500 500 MHz TekVPI® differential voltage probe with ±42 V differential input voltage

TDP1000 1 GHz TekVPI® differential voltage probe with ±42 V differential input voltage

TDP1500 1.5 GHz TekVPI® differential voltage probe with ±8.5 V differential input voltage

TDP3500 3.5 GHz TekVPI® differential voltage probe with ±2 V differential input voltage

THDP0200 ±1.5 kV, 200 MHz TekVPI® high-voltage differential probe

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 31

THDP0100 ±6 kV, 100 MHz TekVPI® high-voltage differential probe

TMDP0200 ±750 V, 200 MHz TekVPI® high-voltage differential probe

Accessories

TPA-N-PRE Preamplifier, 12 dB nominal Gain, 9 kHz - 6 GHz

TPA-N-VPI N-to-TekVPI adapter

119-4146-00 Near field probe set, 100 kHz - 1 GHz

119-6609-00 Flexible monopole antenna

077-0981-xx Service manual (English only)

TPA-BNC TekVPI® to TekProbe™ BNC adapter

TEK-DPG TekVPI Deskew pulse generator signal source

067-1686-xx Power measurement deskew and calibration fixture

SignalVu-PC-SVE Vector Signal Analysis Software

TEK-USB-488 GPIB-to-USB adapter

ACD3000 Soft transit case (includes front protective cover)

HCTEK54 Hard transit case (requires ACD3000)

RMD3000 Rackmount kit

200-5052-00 Front protective cover

Other RF probes

Contact Beehive Electronics to order: http://beehive-electronics.com/probes.html

101A EMC probe set

150A EMC probe amplifier

110A Probe cable

0309-0001 SMA probe adapter

0309-0006 BNC probe adapter

Datasheet

32 www.tektronix.com

Step 4: Add instrument upgrades in the future

Instrument upgrades

The MDO3000 Series products offer a number of ways to add functionality after the initial purchase. Listed below are the various product upgrades available and the method of

upgrade used for each product.

Post-purchase instrument options The following products are sold as stand-alone products and can be purchased at any time to add functionality to any MDO3000

product.

MDO3AFG Add arbitrary function generator to any MDO3000 Series product.

One-time, permanent upgrade to any model enabled through single-use application module hardware key. The hardware key is

used to enable the feature and then is not required for future use.

MDO3MSO Add 16 digital channels; includes P6316 digital probe and accessories .

One-time, permanent upgrade to any model enabled through single-use application module hardware key. The hardware key is

used to enable the feature and then is not required for future use.

MDO3SA Increase spectrum analyzer input frequency range to 9 kHz – 3 GHz and capture bandwidth to 3 GHz.

One-time, permanent upgrade to any model enabled through single-use application module hardware key. The hardware key is

used to enable the feature and then is not required for future use.

MDO3SEC Add enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument

firmware update functionality.

One-time, permanent upgrade to any model enabled through software option key. Software option key products require that the

instrument model and serial number be provided at the time of purchase. The software option key is specific to the model and

serial number combination.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 33

Bandwidth upgrade options Instrument bandwidth can be upgraded on any MDO3000 Series product after initial purchase. Each upgrade product will increase

the analog bandwidth and the spectrum analyzer frequency range to the new bandwidth level. Bandwidth upgrades are purchased

based on the combination of the current bandwidth and the desired bandwidth. Software option key products require that the

instrument model and serial number be provided at the time of purchase. The software option key is specific to the model and

serial number combination. Bandwidth upgrades up to 500 MHz can be performed in the field. Bandwidth upgrades to 1 GHz

require installation at a Tektronix service center. The table below shows the various bandwidth upgrade products to purchase

based on current and desired bandwidth levels.

Model to be upgraded Bandwidth before upgrade Bandwidth after upgrade Order protduct

MDO3012 100 MHz 200 MHz MDO3BW1T22

100 MHz 350 MHz MDO3BW1T32

100 MHz 500 MHz MDO3BW1T52

100 MHz 1 GHz MDO3BW1T102

200 MHz 350 MHz MDO3BW2T32

200 MHz 500 MHz MDO3BW2T52

200 MHz 1 GHz MDO3BW2T102

350 MHz 500 MHz MDO3BW3T52

350 MHz 1 GHz MDO3BW3T102

500 MHz 1 GHz MDO3BW5T102

MDO3014 100 MHz 200 MHz MDO3BW1T24

100 MHz 350 MHz MDO3BW1T34

100 MHz 500 MHz MDO3BW1T54

100 MHz 1 GHz MDO3BW1T104

200 MHz 350 MHz MDO3BW2T34

200 MHz 500 MHz MDO3BW2T54

200 MHz 1 GHz MDO3BW2T104

350 MHz 500 MHz MDO3BW3T54

350 MHz 1 GHz MDO3BW3T104

500 MHz 1 GHz MDO3BW5T104

MDO3022 200 MHz 350 MHz MDO3BW2T32

200 MHz 500 MHz MDO3BW2T52

200 MHz 1 GHz MDO3BW2T102

350 MHz 500 MHz MDO3BW3T52

350 MHz 1 GHz MDO3BW3T102

500 MHz 1 GHz MDO3BW5T102

MDO3024 200 MHz 350 MHz MDO3BW2T34

200 MHz 500 MHz MDO3BW2T54

200 MHz 1 GHz MDO3BW2T104

350 MHz 500 MHz MDO3BW3T54

350 MHz 1 GHz MDO3BW3T104

500 MHz 1 GHz MDO3BW5T104

MDO3032 350 MHz 500 MHz MDO3BW3T52

350 MHz 1 GHz MDO3BW3T102

500 MHz 1 GHz MDO3BW5T102

MDO3034 350 MHz 500 MHz MDO3BW3T54

350 MHz 1 GHz MDO3BW3T104

500 MHz 1 GHz MDO3BW5T104

Datasheet

34 www.tektronix.com

Model to be upgraded Bandwidth before upgrade Bandwidth after upgrade Order protduct

MDO3052 500 MHz 1 GHz MDO3BW5T102

MDO3054 500 MHz 1 GHz MDO3BW5T104

Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.

Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.

Mixed Domain Osciloscopes -- MDO3000 Series

www.tektronix.com 35

Datasheet

ASEAN / Australasia (65) 6356 3900 Austria 00800 2255 4835* Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777

Belgium 00800 2255 4835* Brazil +55 (11) 3759 7627 Canada 1 800 833 9200

Central East Europe and the Baltics +41 52 675 3777 Central Europe & Greece +41 52 675 3777 Denmark +45 80 88 1401

Finland +41 52 675 3777 France 00800 2255 4835* Germany 00800 2255 4835*

Hong Kong 400 820 5835 India 000 800 650 1835 Italy 00800 2255 4835*

Japan 81 (3) 6714 3010 Luxembourg +41 52 675 3777 Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90

Middle East, Asia, and North Africa +41 52 675 3777 The Netherlands 00800 2255 4835* Norway 800 16098

People's Republic of China 400 820 5835 Poland +41 52 675 3777 Portugal 80 08 12370

Republic of Korea 001 800 8255 2835 Russia & CIS +7 (495) 6647564 South Africa +41 52 675 3777

Spain 00800 2255 4835* Sweden 00800 2255 4835* Switzerland 00800 2255 4835*

Taiwan 886 (2) 2722 9622 United Kingdom & Ireland 00800 2255 4835* USA 1 800 833 9200

* European toll-free number. If not accessible, call: +41 52 675 3777 Updated 10 April 2013

For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tektronix.com.

Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and

price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.

04 Feb 2014 48W-30020-1