Previous Datasheet Index Next Data Sheet Bulletin I25196/A ST1200C..K SERIES PHASE CONTROL THYRISTORS Hockey Puk Version 1650A Features Center amplifying gate Metal case with ceramic insulator International standard case A-24 (K-PUK) High profile hockey-puk Typical Applications DC motor controls Controlled DC power supplies AC controllers case style A-24 (K-PUK) Major Ratings and Characteristics Parameters ST1200C..K Units 1650 A 55 C 3080 A 25 C @ 50Hz 30500 A @ 60Hz 32000 A @ 50Hz 4651 KA2s @ 60Hz 4250 KA2s 1200 to 2000 V 200 s - 40 to 125 C IT(AV) @ Ths IT(RMS) @ Ths ITSM I 2t V DRM /V RRM tq TJ typical To Order Previous Datasheet Index Next Data Sheet ST1200C..K Series ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM /V RRM , max. repetitive VRSM , maximum non- I DRM/I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max V V mA 12 1200 1300 14 1400 1500 16 1600 1700 18 1800 1900 20 2000 2100 Type number ST1200C..K 100 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature I T(RMS) Max. RMS on-state current I TSM 2 I t ST1200C..K Units Conditions 1650 (700) A 180 conduction, half sine wave 55 (85) C double side (single side) cooled 3080 DC @ 25C heatsink temperature double side cooled Max. peak, one-cycle 30500 t = 10ms No voltage non-repetitive surge current 32000 t = 8.3ms reapplied 25700 t = 10ms 100% VRRM 26900 t = 8.3ms reapplied Sinusoidal half wave, 4651 t = 10ms No voltage Initial T J = TJ max. t = 8.3ms reapplied t = 10ms 100% VRRM t = 8.3ms reapplied 2 Maximum I t for fusing 4250 A KA2s 3300 3000 I t 2 Maximum I t for fusing 2 V T(TO) 1 Low level value of threshold voltage V T(TO)2 High level value of threshold 46510 KA s 2 (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. 0.91 V 1.01 (I > x IT(AV)),TJ = TJ max. 0.21 (16.7% x x IT(AV) < I < x IT(AV) ), TJ = TJ max. voltage r t1 Low level value of on-state slope resistance r t2 High level value of on-state slope resistance t = 0.1 to 10ms, no voltage reapplied m (I > x IT(AV) ),TJ = TJ max. 0.19 V TM Max. on-state voltage 1.73 IH Maximum holding current 600 IL Typical latching current 1000 V Ipk= 4000A, TJ = TJ max, t p = 10ms sine pulse mA T J = 25C, anode supply 12V resistive load To Order Previous Datasheet Index Next Data Sheet ST1200C..K Series Switching Parameter di/dt ST1200C..K Max. non-repetitive rate of rise 1000 of turned-on current t d Typical delay time Units Conditions A/s Typical turn-off time TJ = TJ max, anode voltage 80% VDRM Gate current 1A, di g /dt = 1A/s 1.9 s tq Gate drive 20V, 20, tr 1s 200 Vd = 0.67% VDRM, TJ = 25C ITM = 550A, TJ = TJ max, di/dt = 40A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, tp = 500s Blocking Parameter dv/dt Maximum critical rate of rise of IRRM IDRM Max. peak reverse and off-state leakage current ST1200C..K Units Conditions 500 off-state voltage V/s TJ = TJ max. linear to 80% rated VDRM 100 mA TJ = TJ max, rated V DRM /VRRM applied Triggering Parameter PGM ST1200C..K Maximum peak gate power Max. peak positive gate current +VGM Maximum peak positive 3 3.0 Maximum peak negative TJ = TJ max, t p 5ms V TJ = TJ max, tp 5ms TYP. MAX. 200 - 100 200 50 - TJ = 125C 1.4 - TJ = - 40C 1.1 3.0 0.9 - TJ = - 40C DC gate current required to trigger VGT A 5.0 gate voltage IGT TJ = TJ max, t p 5ms TJ = TJ max, f = 50Hz, d% = 50 20 gate voltage -VGM W 16 PG(AV) Maximum average gate power IGM Units Conditions DC gate voltage required to trigger mA V TJ = 25C Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = 25C TJ = 125C IGD DC gate current not to trigger 10 mA VGD DC gate voltage not to trigger 0.25 V TJ = TJ max To Order Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Previous Datasheet Index Next Data Sheet ST1200C..K Series Thermal and Mechanical Specification Parameter ST1200C..K TJ Max. operating temperature range -40 to 125 Tstg Max. storage temperature range -40 to 150 RthJ-hs Max. thermal resistance, Units C 0.042 junction to heatsink DC operation single side cooled K/W 0.021 RthC-hs Max. thermal resistance, 0.006 case to heatsink 0.003 Mounting force, 10% 24500 N (2500) (Kg) Approximate weight 425 g Case style A-24 (K-PUK) F wt Conditions K/W DC operation double side cooled DC operation single side cooled DC operation double side cooled See Outline Table RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Single Side Double Side Single Side Double Side 180 0.003 0.003 0.002 0.002 120 0.004 0.004 0.004 0.004 90 0.005 0.005 0.005 0.005 60 0.007 0.007 0.007 0.007 30 0.012 0.012 0.012 0.012 Units Conditions TJ = TJ max. K/W Ordering Information Table Device Code ST 120 1 2 0 C 20 K 1 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - K = Puk Case A-24 (K-PUK) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/sec (Standard selection) L = 1000V/sec (Special selection) To Order Previous Datasheet Index Next Data Sheet ST1200C..K Series Outline Table 1 (0.04) MIN. TWO PLACES 47.5 (1.87) DIA. MAX. 27.5 (1.08) MAX. TWO PLACES PIN RECEPTACLE AMP. 60598-1 Case Style A-24 (K-PUK) 67 (2.6) DIA. MAX. All dimensions in millimeters (inches) 20 5 74.5 (2.9) DIA. MAX. 4.75 (0.2) NOM. 44 (1.73) 2 HOLES DIA. 3.5 (0.14) x 2.1 (0.1) DEEP Maximum Allowable Heatsink Temperature (C) Maximum Allowable Heatsink Temperature (C) CREPAGE DESTANCE 28.88 (1.137) MIN. STRIKE DISTANCE 17.99 (0.708) MIN. 130 ST1200C..K Series (Single Side Cooled ) RthJ-hs(DC) = 0.042 K/ W 120 110 100 90 Conduc tion Angle 80 30 60 70 90 60 120 180 50 40 0 200 400 600 800 1000 1200 ST1200C..K Series (Single Side Cooled) RthJ-hs(DC) = 0.042 K/ W 120 110 100 90 Conduction Period 80 70 60 30 50 40 60 90 120 30 180 20 0 400 800 1200 DC 1600 2000 Average On-state Current (A) Average On-state Current (A) Fig. 1 - Current Ratings Characteristics 130 To Order Fig. 2 - Current Ratings Characteristics Previous Datasheet Index Next Data Sheet 130 ST1200C..K Series (Double Side Cooled) RthJ-hs(DC) = 0.021 K/W 120 110 100 90 Conduc tion Angle 80 70 30 60 60 90 50 120 180 40 30 0 400 800 1200 1600 2000 Maximum Allowa ble Heatsink Temperature (C) Maximum Allowable Heatsink Temperature (C) ST1200C..K Series 130 ST1200C..K Series (Double Side Cooled) RthJ-hs(DC) = 0.021 K/ W 120 110 100 90 Conduction Period 80 70 60 50 40 30 30 0 500 1000 1500 2000 2500 3000 3500 RMS Limit 2500 2000 1500 Conduction Angle 1000 ST1200C..K Series TJ = 125C 500 0 0 400 800 1200 1600 Maximum Average On-state Power Loss(W) Maximum Average On-state Power Loss (W) Fig. 4 - Current Ratings Characteristics 180 120 90 60 30 3000 5000 DC 180 120 90 60 30 4000 3000 RMS Limit 2000 Conduction Period ST1200C..K Series TJ = 125C 1000 0 0 2000 Average On-state Current (A) 24000 22000 20000 18000 16000 14000 ST1200C..K Series 12000 1 10 Fig. 6- On-state Power Loss Characteristics Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) At Any Rated Load Condition And With Rated VRRM Applied Following Surge. Initial TJ = 125C @60 Hz 0.0083 s @50 Hz 0.0100 s 26000 500 1000 1500 2000 2500 3000 3500 Average On-state Current (A) Fig. 5- On-state Power Loss Characteristics 28000 DC Average On-state Current (A) Fig. 3 - Current Ratings Characteristics 3500 180 20 Average On-state Current (A) 4000 90 60 120 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled 32000 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. 28000 Initial TJ = 125C No Voltage Reapplied 26000 Rated VRRMReapplied 24000 30000 22000 20000 18000 16000 14000 12000 0.01 ST1200C..K Series 0.1 1 Pulse Train Duration (s) To Order Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Previous Datasheet Index Next Data Sheet ST1200C..K Series Instantaneous On-state Current (A) 10000 1000 TJ = 25C TJ = 125C ST1200C..K Series 100 0.5 1 1.5 2 2.5 3 Instantaneous On-state Voltage (V) Transient Thermal Impedance Z thJ-hs (K/ W) Fig. 9 - On-state Voltage Drop Characteristics 0.1 Steady State Value R thJ-hs = 0.042 K/ W (Single Side Cooled) R thJ-hs = 0.021 K/ W (Double Side Cooled) 0.01 (DC Operation) ST1200C..K Series 0.001 0.001 0.01 0.1 1 10 100 Square Wave Pulse Duration (s) Fig. 10 - Thermal Impedance ZthJ-hs Characteristics Rectangular gate pulse a) Recommended load line for rated di/dt : 20V, 10ohms; tr<=1 s b) Recommended load line for <=30%rated di/dt : 10V, 10ohms 10 tr<=1 s (1) PGM = 16W, tp = 4ms (2) PGM = 30W, tp = 2ms (3) PGM = 60W, tp = 1ms (a) (b) IGD 0.1 0.001 0.01 Tj=-40 C VGD Tj=25 C 1 Tj=125 C Instantaneous Gate Voltage (V) 100 (1) (2) Device: ST1200C..K Series 0.1 (3) Frequency Limited by PG(AV) 1 10 Instantaneous Gate Current (A) Fig. 11 - Gate Characteristics To Order 100