CMX589AP4 - MX-COM, Inc. - Datasheet.Live

DATA BULLETIN

CMX589A

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

HIGH-SPEED

GMSK MODEM

PRELIMINARY INFORMATION

Features Applications

 Data Rates from 4kbps to 200kbps

 Full or Half Duplex Gaussian Filter & Data Recovery

for Minimum Shift Keying (GMSK) Designs

 Selectable BT: (0.3 or 0.5)

 Low Power

3.0V, 20kbps, 1.5mA typ.

5.0V, 64kbps, 4.0mA typ.

 Low Current Non-DSP Solution

 Small TSSOP size fits PCMCIA / PC CARDs

 Portable Wireless Data Applications

Cellular Digital Packet Data (CDPD)

Mobitex Mobile Data System

 Spread Spectrum Data Links

 GPS/Differential GPS Wireless Links

 Point of Sale Terminals

 Low Power Wireless Data Link for PCs,

Laptops, and Printers

TX PS

RX PS

TX DATA

ClkDIVA

PLLacq

RXDCacq

RX SIGNAL IN

RX FEEDBACK

CLOCK

DIVIDER

XTAL/CLOCK

TX ENABLE

XTAL

BIAS

RXHold

RX CLK

TX CLK

TX OUT

RX DATA

RX S/N

DOC1 DOC2

ClkDIVB

RX CIRCUIT

CONTROL

FILTER

DATA RETIME &

LEVEL SHIFT TX

FILTER

RX S/N

DETECTION

RX CLOCK

RX DC LEVEL

MEASURE

BIAS

RX DATA

DETECTION

The CMX589A is a single-chip synchronous data pump/modem designed for Wireless Data Applications.

Employing Gaussian filtering for Minimum shift Keying (GMSK) baseband modulation applications, the

CMX589A features a wide range of available data rates from 4k to 200kbps. Data Rates and the choice of BT

(0.3 or 0.5) are pin programmable to provide for different system requirements.

The Tx and Rx digital data interfaces are bit serial, synchronized to generated Tx and Rx data clocks.

Separate Tx and Rx Powersave inputs allow full or half-duplex operation. Rx input levels can be set by

suitable AC and DC level adjusting circuitry built with external components around an on-chip Rx Input

Amplifier.

Acquisition, Lock, and Hold of Rx data signals are made easier and faster by the use of Rx Control Inputs to

clamp, detect, and /or hold input data levels and can be set by the Processor as required. The Rx S/N

output provides an indication of the quality of the received signal.

The CMX589A may be used with a 3.0V to 5.5V power supply and is available in the following packages:

24-pin TSSOP (CMX589AE2), 24-pin SSOP (CMX589AD5), 24-pin SOIC (CMX589AD2), and 24-pin PDIP

(CMX589AP4).

High Speed GMSK Modem 2 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

Contents

Section Page

1 Block Diagram................................................................................................................3

2 Signal List.......................................................................................................................4

3 External Components....................................................................................................6

4 General Description.......................................................................................................8

4.1 Clock Oscillator Divider ....................................................................................................... 8

4.2 Receive................................................................................................................................ 8

4.2.1 Rx Signal Path Description.....................................................................................................8

4.2.2 Rx Circuit Control Modes .......................................................................................................9

4.2.3 Rx Clock Extraction..............................................................................................................10

4.2.4 Rx Data Extraction ...............................................................................................................10

4.2.5 Rx S/N Detection..................................................................................................................11

4.2.6 Rx Signal Quality..................................................................................................................12

4.3 Transmit............................................................................................................................. 12

4.3.1 TX Signal Path Description ..................................................................................................12

4.4 Data Formats..................................................................................................................... 14

4.5 Acquisition and Hold Modes.............................................................................................. 14

5 Application ...................................................................................................................15

5.1 Radio Channel Requirements ........................................................................................... 15

5.1.1 Bit Rate, BT, and Bandwidth................................................................................................15

5.1.2 FM Modulator, Demodulator and IF .....................................................................................15

5.1.3 Two-Point Modulation...........................................................................................................16

5.2 AC Coupling of Tx and Rx Signals.................................................................................... 17

6 Performance Specifications........................................................................................18

6.1 Electrical Specifications..................................................................................................... 18

6.1.1 Absolute Maximum Limits ....................................................................................................18

6.1.2 Operating Limits...................................................................................................................18

6.1.3 Operating Characteristics.....................................................................................................19

6.2 Packages........................................................................................................................... 20

MXCOM, Inc. reserves the right to change specifications at any time without notice.

High Speed GMSK Modem 3 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

1 Block Diagram

TX PS

RX PS

TX DATA

ClkDIVA

PLLacq

RXDCacq

RX SIGNAL IN

RX FEEDBACK

CLOCK

DIVIDER

XTAL/CLOCK

TX ENABLE

XTAL

BIAS

RXHold

RX CLK

TX CLK

TX OUT

RX DATA

RX S/N

DOC1 DOC2

ClkDIVB

RX CIRCUIT

CONTROL

FILTER

DATA RETIME &

LEVEL SHIFT TX

FILTER

RX S/N

DETECTION

RX CLOCK

RX DC LEVEL

MEASURE

BIAS

RX DATA

DETECTION

Figure 1: Block Diagram

RX Frequency

Discriminator Frequency

Modulator

Signal and

DC Level

Adjustment

DC Level

Adjust

RX Sig In

RX Feedback

RX circuits

TX circuits

RXD

RXC

TXD

TXC

uController

or UART

RX Data

RX Clock

TX Data

TX Clock

CMX589A

GMSK MODEM

TX Out

Filter

RX Filter

and Gain

Figure 2: System Block Diagram

High Speed GMSK Modem 4 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

2 Signal List

Pin No.

E2/D5/

D2/P4

Signal Type Description

1XTAL output The output of the on-chip clock oscillator.

2 XTAL/CLOCK input The input to the on-chip Xtal oscillator. A Xtal, or externally derived

clock (fXTAL) pulse input should be connected here. If an externally

generated clock is to be used, it should be connected to this pin and the

XTALpin left unconnected. Note: Operation without a suitable Xtal or

clock input may cause device damage.

3 ClkDivA input Logic level inputs control the internal clock divider and therefore the

transmit and receive data rate. See Table 4.

4 ClkDivB input Logic level inputs control the internal clock divider and therefore the

transmit and receive data rate. See Table 4.

5HOLDRx input A logic 0 applied to this input will freeze the Clock Extraction and Level

Measurement circuits unless they are in ‘Acquire’ mode.

6 RxDCacq input A logic 1 applied to this input will set the RX Level Measurement circuitry

to the Acquire mode.

7 PLLacq input A logic 1 applied to this input will set the RX Clock Extraction circuitry to

the ‘Acquire’ mode. See Table 6.

8 Rx PSAVE input A logic 1 applied to this input will powersave all receive circuits except

for RX CLK output (which will continue at the set bit-rate) and cause the

RX Data and RX S/N outputs to go to a logic 0.

9VBIAS The internal circuitry bias line, held at VDD/2. This pin must be bypassed

to VSS by a capacitor mounted close to the pin.

10 Rx FB Output of the RX Input Amplifier.

11 Rx Signal In input Input to RX input amplifier.

12 VSS power Negative supply (GND).

13 DOC1 Connections to the RX Level Measurement Circuitry. A capacitor should

be connected from each pin to VSS.

14 DOC2 Connections to the RX Level Measurement Circuitry. A capacitor should

be connected from each pin to VSS.

15 BT A logic level to select the modem BT (the ratio of the TX Filter's -3dB

frequency to the Bit-Rate). A logic 1 = BT of 0.5 and a logic 0 = BT of

0.3.

16 Tx Out output Gaussian filtered TX output signal. In powersave mode the Tx Out pin is

a high impedance open.

17 Tx Enable input A logic 1 applied to this input, enables the transmit data path, through

the TX Filter to the TX Out pin. A logic 0 will place the TX Out pin to

VBIAS via a high impedance.

18 Tx PSAVE input A logic 1 applied to this input will powersave all transmit circuits except

for the TX Clock.

19 Tx Data input The logic level input for the data to be transmitted. This data should be

synchronous with TX CLK.

20 Rx Data output A logic level output carrying the received data, synchronous with

RX CLK.

21 Rx CLK output A logic level clock output at the received data bit-rate.

22 Tx CLK output A logic level clock output at the transmit-data rate.

High Speed GMSK Modem 5 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

Pin No.

E2/D5/

D2/P4

Signal Type Description

23 Rx S/N output A logic level output which may be used as an indication of the quality of

the received signal.

24 VDD power Positive supply. Levels and voltages within the device are dependent

upon this supply. This pin should be bypassed to VSS by a capacitor

mounted close to the pin.

Table 1: Signal List

High Speed GMSK Modem 6 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

3 External Components

ClkDivA

ClkDivB

RX HOLD

RXDCacq

PLLacq

RX PSAVE

BIAS

RX FB

RX SIGNAL IN

RX S/N

TXCLK

RXCLK

RXDATA

TXDATA

TXPSAVE

TXENABLE

TXOUT

DOC2

DOC1

CMX589A

E2/D5/D2/P4

C7 C8

XTAL/CLOCK

XTAL

Suggested Clock Circuits

XTAL

XTAL/CLOCK

C2 X1 R2

Crystal Circuit

XTAL

XTAL/CLOCK

C9 R2

EXT CLK

External Clk > 10.24MHz Circuit

XTAL

EXT CLK XTAL/CLOCK

External Clk 10.24MHz Circuit≤

Figure 3: Recommended External Components

Component Notes Value Tolerance Component Notes Value Tolerance

R1 1 ±5% C4 0.1µF ±20%

R2 1.0M±10% C5 1.0µF ±20%

R3 2 ±10% C6 5 ±20%

R4 3 ±10% C7 6

C1 1 ±10% C8 6

C2 4 C9 7 100pF

C3 4 X1 8

Table 2: Recommended External Components

Recommended External Component Notes:

1. The RC network formed by R1 and C1 is required between the TX Out pin and the input to the modulator.

This network, which can form part of any DC level shifting and gain adjustment circuitry, forms an

important part of the transmit signal filtering. The ground connection to the capacitor C1 should be

positioned to give maximum attenuation of high-frequency noise into the modulator.

The component values should be chosen so that the product of the resistance and the capacitance is:

For a BT of 0.3 R1C1 = 0.34/bit rate (bps)

For a BT of 0.5 R1C1 = 0.22/bit rate (bps)

High Speed GMSK Modem 7 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

BT = 0.3 BT = 0.5

Data Rates

(kbps) R1 C1 R1 C1

4120k680pF 120k470pF

4.8 100k680pF 100k470pF

891k470pF 120k220pF

9.6 91k390pF 47k470pF

16 47k470pF 91k150pF

19.2 100k180pF 91k120pF

32 47k220pF 47k150pF

38.4 * 47k180pF 47k120pF

64 * 56k100pF 51k68pF

80 * 39k68pF

128 * 82k22pF

144 * 68k22pF

160 * 62k22pF

176 * 56k22pF

192 * 51k22pF

* VDD  4.5V, external clock

Table 3: Data Rate vs. BT and Selected External Component Values

Note: In all cases, the value of R1 should not be less than 20.0k, and that the calculated value of C1

includes calculated parasitic capacitance.

2. R3, R4 and C6 form the gain components for the RX Input signal. R3 should be chosen as required by

the signal input level.

3. For bit rate  64kbps, R4 = 100k. For bit rate > 64kbps, R4 = 10k.

4. The values chosen for C2 and C3 (including stray capacitance) should be suitable for the applied VDD

and the frequency of X1.

As a guide: C2 = C3 = 33pF at 1.0MHz falling to 18pF at the maximum frequency.

At 3.0V, C2 = C3 = 33pF falling to 18pF at 5.0MHz the equivalent series resistance of X1 should be less

than 2.0K falling to 150 at the maximum frequency. Stray capacitance on the Xtal/Clock circuit pins

must be minimized.

5. For bit rate  64kbps, C6 = 22pF. For bit rate > 64kbps, C6 =  10k 2 rate bit 3 1 e.g. for 128kbps,

C6 = 41.1pF.

6. C7 and C8 should both be .015F for a data rate of 8kbps, and inversely proportional to the data rate for

other data rates, e.g. 0.030F at 4kbps, 1800pF at 64kbps, 680pF at 192kbps.

7. The tolerance of C9 is not very critical because it primarily serves as a DC blocking capacitor.

8. The CMX589A can operate correctly with the Xtal/Clock frequencies between 1.0MHz and 8.2MHz

(VDD = 5.0V) and 1.0MHz to 5.0MHz (VDD = 3.0V). External clock frequencies up to 25.6MHz

(VDD  4.5V) are also supported. (See Table 4 for examples.) For best results, a crystal oscillator design

should drive the clock inverter input with signal levels of at least 40% of VDD, peak to peak. Tuning fork

crystals generally cannot meet this requirement. To obtain crystal oscillator design assistance, consult

your crystal manufacturer. Operation of this device without a Xtal or Clock input may cause device

damage.

High Speed GMSK Modem 8 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

4 General Description

4.1 Clock Oscillator Divider

The TX and (nominal) RX data rates are determined by division of the frequency present at the Xtalpin as

generated by the on-chip Xtal oscillator, with external components, or supplied from an external source.

The division ratio is controlled by the logic level inputs on ClkDivA and ClkDivB pins as shown in Table 4,

together with an indication of how various standard data rates may be derived from common µP Xtal

frequencies.

A/B)(ClkDiv Ratio Division Frequency Xtal/Clk

Rate Data 

Xtal/Clock Frequency (MHz)

24.576* 8.192 4.9152 4.096 2.4576 2.048

Inputs 12.288/3 12.288/5 6.144/3

ClkDivA ClkDivB Rate Data Freq Xtal/Clk

Data Rate (kbps)

0 0 128 192* 64* 38.4* 32 19.2 16

0 1 256 96* 32 19.2 16 9.6 8

1 0 512 48* 16 9.6 8 4.8 4

1 1 1024 24* 8 4.8 4

* VDD  4.5V

Table 4: Example Clock/Data Rates

Note: The device operation is not guaranteed above 200kbps or below 4kbps at the relevant supply voltage.

Tx Enable

ClkDIVA

ClkDIVB

RxHOLD

Rx S/N

Tx PS

Rx PS

XTAL/CLOCK

XTAL

Rx DATA

Rx CLOCK

Tx DATA

Tx ClOCK

PLLacq

RxDCacq

RxD

RxC

TxD

TxC

SERIAL

I/O PORT

µCONTROLLER

SETTINGS: D/RATE 4800 bps -BT 0.5 - Rx and Tx Enabled

CMX589A

GMSK MODEM

4.9152MHz

Figure 4: Minimum Controller System Connections

4.2 Receive

4.2.1 Rx Signal Path Description

The function of the RX circuitry is to:

1. Set the incoming signal to a usable level.

2. Clean the signal by filtering.

3. Provide DC level thresholds for clock and data extraction.

4. Provide clock timing information for data extraction and external circuits.

5. Provide RX data in a binary form.

6. Assess signal quality and provide Signal-to-Noise information.

High Speed GMSK Modem 9 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

The output of the radio receiver's Frequency Discriminator should be fed to the CMX589A's RX Filter by a

suitable gain and DC level adjusting circuit. This circuit can be built with external components around the on-

chip RX Input Amplifier. The gain should be set so that the signal level at the RX Feedback pin is nominally

1V peak to peak (for VDD=5.0V) centered around VBIAS when receiving a continuous 1111000011110000..

data pattern.

Positive going signal excursions at RX Feedback pin will produce a logic 0 at the RX Data Output. Negative

going excursions will produce a logic 1.

The received signal is fed through the lowpass RX Filter, which has a -3dB corner frequency of 0.56 times the

data bit-rate, before being applied to the Level Measure and Clock and Data extraction blocks.

The Level Measuring block consists of two voltage detectors, one of which measures the amplitude of the

positive parts of the received signal. The other measures the amplitude of the negative portions. (Positive

refers to signal levels higher than VDD/2, and negative to levels lower than VDD/2.) External capacitors are

used by these detectors, via the Doc1 & Doc2 pins, to form voltage ‘hold’ or ‘integrator’ circuits. These two

levels are then used to establish the optimum DC level decision-thresholds for the Clock and Data extraction,

depending upon the RX signal amplitude and any DC offset.

4.2.2 Rx Circuit Control Modes

The operating characteristics of the Rx Level Measurement and Clock Extraction circuits are controlled, as

shown in Table 6, by logic level inputs applied to the PLLacq, HOLDRx , and RxDCacq pins to suit a

particular application, or to cope with changing reception conditions, reference Figure 5.

In general, a data transmission will begin with a preamble, for example, 1100110011001100, to allow the

receive modem to establish timing and level-lock as quickly as possible. After the Rx carrier has been

detected, and during the time that the preamble is expected, the RxDCacq and PLLacq Inputs should be

switched from a logic 0 to a logic 1 so that the Level Measuring and Clock Extraction modes are operated and

sequenced as shown.

The HOLDRx input should normally be held at a logic 1 while data is being received, but may be driven to a

logic 0 to freeze the Level Measuring Clock Extraction circuits during a fade. If a fade lasts for less than 200

bit periods, normal operation can be resumed by returning the HOLDRx input to a logic 1 at the end of the

fade. For longer fades, it may be better to reset the Level Measuring circuits by placing the RxDCacq to a

logic 1 for 10 to 20 bit periods.

HOLDRx has no effect on the Level Measuring circuits while RxDCacq is at a logic 1, and has no effect on

the PLL while PLLacq is at a logic 1.

A logic 0 on HOLDRx does not disable the Rx Clock output, and the Rx Data Extraction and S/N Detector

circuits will continue to operate.

Rx Signal Input

Rx CARRIER DET

(RSSI) Input

RxDCacq

Rx LEVEL MEASURE

MODE

PLLacq

CLOCK EXTRACTION

CCT MODE

FAST PEAK

DETECT

30 BITS

MEDIUM

BANDWIDTH NARROW

BANDWIDTH

AVERAG ING PEAK

DETECT

ACQUIRE

CLAMP

PREAMBLE DATA

Figure 5: Rx Mode Control Diagram

High Speed GMSK Modem 10 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

PLLacq RxHOLD PLL Action

1 1 Acquire Sets the PLL bandwidth wide enough to allow a lock to the

received signal in less than 8 zero crossings. This mode will

operate as long as PLLacq is a logic “1”.

1 to 0 1 Medium

Bandwidth The correction applied to the extracted clock is limited to a

maximum of ±1/16th bit-period for every two received zero-

crossings. The PLL operates in this mode for a period of

about 30 bits immediately following a 1 to 0 transition of the

PLLacq input, provided that the HOLDRx input is a logic 1.

0 1 Narrow

Bandwidth The correction applied to the extracted clock is limited to a

maximum of ±1/64th bit-period for every two received zero-

crossings. The PLL operates in this mode whenever the

HOLDRx Input is a logic 1 and PLLacq has been a logic 0

for at least 30 bit periods (after Medium Bandwidth operation

for instance).

0 0 Hold The PLL feedback loop is broken, allowing the RX Clock to

freewheel during signal fade periods.

Table 5: PLL Action Measurement Operational Modes

RxDCacq RxHOLD Rx Level Measure Action

0 to 1 X Clamp Operates for one bit-time after a 0 to 1 transition of the

RXDCacq input. The external capacitors are rapidly charged

towards a voltage mid-way between the received signal input

level and VBIAS, with the charge time-constant being of the

order of 0.5 bit-time.

1 X Fast Peak Detect The voltage detectors act as peak-detectors, one capacitor is

used to capture the positive-going signal peaks of the RX

Filter output signal and the other capturing the negative-

going peaks. The detectors operate in this mode whenever

the RXDCacq input is at a logic 1, except for the initial 1-bit

Clamp-mode time.

Averaging Peak

Detect Provides a slower but more accurate measurement of the

signal peak amplitudes.

0 0 Hold The capacitor charging circuits are disabled so that the

outputs of the voltage detectors remain substantially at the

last readings (discharging very slowly [time-constant approx.

2,000 bits] towards VBIAS).

X = Do not care

Table 6: Rx Level Measurement Operational Modes

4.2.3 Rx Clock Extraction

Synchronized by a PLL circuit to zero-crossings of the incoming data, the Rx Clock Extraction circuitry

controls the Rx Clock output. The Rx Clock is also used internally by the Data Extraction circuitry. The PLL

parameters can be varied by the Rx Circuit Control inputs PLLacq and HOLDRx to operate in one of four

PLL modes as described in Table 5 and Table 6.

4.2.4 Rx Data Extraction

The RX Data Extraction circuit decides whether each received bit is a 1 or 0 by sampling the received signal,

after filtering, and comparing the sample values to an adaptive threshold derived from the Level Measuring

circuit. This threshold is adapted from bit to bit to compensate for intersymbol interference caused by the

bandlimiting of the overall transmission path and the Gaussian premodulation filter. Extracted data is output

from the RX Data pin, and should be sampled externally on the rising edge of the RX CLK.

High Speed GMSK Modem 11 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

4.2.5 Rx S/N Detection

The RX S/N Detector system classifies the incoming zero-crossings as GOOD or BAD depending upon the

time when each crossing actually occurs with respect to its expected time as determined by the Clock

Extraction PLL. This information is then processed to provide a logic level output at the RX S/N pin. A high

level indicates a series of GOOD crossings; a low level indicates a BAD crossing.

By averaging this output, it is possible to derive a measure of the Signal-to-Noise-Ratio and hence the

Bit-Error-Rate of the received signal.

-6

-5

-4

-3

-2

-1

5678910

11 12 13 14 15 16 17 18 19 20

S/N (dB) [Noise Bandwidth = Bit Rate]

BER

CMX589A BT = 0.3

CMX589A BT = 0.5

BT = 1.0 (Theoretical)

Figure 6: Typical Bit-Error-Rate Performance

Note: Figure 6 indicates typical performance, independent of bit rate (although the applied noise bandwidth is

considered to match the bit rate used), radio performance (e.g. IF filter distortion), supply voltage (higher bit

rates require VDD  4.5V), and other ‘real world’ factors.”

High Speed GMSK Modem 12 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

4.2.6 Rx Signal Quality

The effect of input Rx Signal quality on the Rx S/N output is shown in Figure 7.

100

678910

11 12 13

S/N (dB)

% High Time

BT=0.5

BT = 0.3

Figure 7: Typical Rx S/N Output High time (%) vs. Input S/N

4.3 Transmit

4.3.1 TX Signal Path Description

The binary data applied to the TX Data input is retimed within the chip on each rising edge of the TX Clock

and then converted to a 1-volt peak-to-peak binary signal centered at VBIAS (for VDD= 5.0V)

If the TX Enable input is high, then this internal binary signal will be connected to the input of the lowpass TX

Filter, and the output of the filter connected to the TX Out pin.

Tx Enable Tx Filter Input Tx Out Pin

1Data @ 5

VDD VP-P

e.g. 1VP-P for VDD=5V

Filtered ‘Tx Filter Input’

0VBIAS VBIAS via 500k

A ‘low’ input to the TX Enable will connect the input of the TX Filter to VBIAS, and disconnect the TX Out pin

from the filter, connecting it instead to VBIAS through a high resistance (nominally 500k).

The TX Filter has a lowpass frequency response, which is approximately gaussian in shape as shown in

Figure 9, to minimize amplitude and phase distortion of the binary signal while providing sufficient attenuation

of the high frequency-components which would otherwise cause interference into adjacent radio channels.

The actual filter bandwidth to be used in any particular application will be determined by the overall system

requirements. The attenuation-vs.-frequency response of the transmit filtering provided by the CMX589A has

been designed to meet the specifications for most GMSK modem systems that are -3dB bandwidth

switchable between 0.3 and 0.5 times the data bit-rate (BT).

Note: An external RC network is required between the TX Out pin and the input to the Frequency Modulator

(see Figure 2 and Figure 3). This network, which can form part of any DC level shifting and gain adjustment

circuitry, forms an important part of the transmit signal filtering. The ground connection to capacitor C1

should be positioned to give maximum attenuation of high-frequency noise into the modulator.

The signal at Tx Out is centered around VBIAS, going positive for logic 1 (high) level inputs to the Tx Data

input and negative for logic 0 (low) inputs.

When the transmit circuits are put into a powersave mode (by a logic 1 to the Tx PS pin) the output voltage of

the Tx Filter will go to high impedance. When power is subsequently restored to the Tx filter, its output will

take several bit-times to settle. The Tx Enable input can be used to prevent these abnormal voltages from

appearing at the Tx Out pin.

High Speed GMSK Modem 13 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

1 BIT PERIOD

1.0 s Min.µ

TX DATA SAMPLED BY

THE CMX589A AT THESE

INSTANCES

TX Data

RX Data

RX CLK

TX CLK

DON'T CARE

DATA INVALID DATA VALID

DATA MUST

BE VALID

EXTERNAL CIRCUITS SHOULD

SAMPLE RX DATA AT THIS TIME

TX CLOCK AND RX CLOCK OUTPUTS

(MARK/SPACE) DUTY CYCLE NOMINALLY 50%.

1.0 s Max.µ1.0 s Max.µ

1.0 s Min.µ

Figure 8: Rx and Tx Clock Data Timings

BT = 0.3 BT = 0.5

-10

-20

-30

-40

-50

-60

-70 0.1 10

0.01 Frequency/Bitrate

Gain (dB)

Figure 9: Tx Filter Response

High Speed GMSK Modem 14 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

BT = 0.3 BT = 0.5

Figure 10: Typical Transmit Eye Patterns

-70

-60

-50

-40

-30

-20

-10

01.0

2.0

Gain (dB)

Frequency/Bitrate

BT = 0.3 BT=0.5

Figure 11: Tx Output Spectrum (Random Data)

4.4 Data Formats

The receive section of the CMX589A works best with data which has a reasonably random structure --the

data should contain approximately the same number of ‘ones’ as ‘zeroes’ with no long sequences (>100 bits)

of consecutive ones or zeroes. Also, long sequences (>100 bits) of 10101010 ... patterns should be avoided.

For this reason, it is recommended that data be made random in some manner before transmission, for

example by exclusive-ORing it with the output of a binary pseudo-random pattern generator.

Where data is transmitted in bursts, each burst should be preceded by a preamble designed to allow the

receive modem to establish timing and level lock as quickly as possible. This preamble for BT=0.3 should be

at least 16 bits long, and should preferably consist of alternating pairs of ones and zeros i.e.

110011001100....; the eye of pattern 10101010 .... has the most gradual slope and will yield poor peak levels

for the RX circuits. For BT=0.5 the eye pattern of 10101010... has reduced intersymbol interference and may

be used as the preamble (DC Acq pin should be held high during preamble). See Fig. 6.

4.5 Acquisition and Hold Modes

The RXDCacq and PLLacq inputs must be pulsed High for about 16 bits at the start of reception to ensure

that the DC measurement and timing extraction circuits lock-on to the received signal correctly. Once lock

has been achieved, the above inputs should be taken Low again.

In most applications, there will be a DC step in the output voltage from the receiver FM discriminator due to

carrier frequency offsets as channels are changed or when the remote transmitter is turned on.

The CMX589A can tolerate DC offsets in the received signal of at least ±0.5V with respect to VBIAS,

(measured at the RX Feedback pin). However, to ensure that the DC offset compensation circuit operates

correctly and with minimum delay, the Low to High transition of the RXDCacq and PLLacq inputs should

occur after the mean input voltage to the CMX589A has settled to within about 0.1V of its final value.

Note: This can place restrictions on the value of any series signal coupling capacitor.

High Speed GMSK Modem 15 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

As well as using the RX Hold input to freeze the Level Measuring and Clock Extraction circuits during a signal

fade, it may also be used in systems which use a continuously transmitting control channel to freeze the RX

circuitry during transmission of a data packet, allowing reception to resume afterwards without losing bit

synchronization. To achieve this, the CMX589A Xtal clock needs to be accurate enough that the derived

RXClock output does not drift by more than about 0.1 bit time from the actual received data-rate during the

time that the RXHold input is ‘Low’.

However; the RXDCacq input may need to be pulsed High for 2 bit durations to re-establish the level

measurements if the RXHold input is Low for more that a few hundred bit-times (exact number depends on

system crystal tolerances).

The voltages on the Doc1 and Doc2 pins reflect the average peak positive and negative excursions of the

(filtered) receive signal, and could therefore be used to derive a measure of the data signal amplitude.

Note: These pins are driven from very high-impedance circuits, so that the DC load presented by any

external circuitry should exceed 10M to VBIAS.

5 Application

5.1 Radio Channel Requirements

To achieve legal adjacent channel performance at high bit-rates, a radio with an accurate carrier frequency

and an accurate modulation index is required. For optimum channel utilization, (e.g. low BER and high data-

rates) attention must be paid to the phase and frequency response of both the IF and baseband circuitry.

5.1.1 Bit Rate, BT, and Bandwidth

The maximum data rate that can be transmitted over a radio channel depends on the following:

Channel spacing

Allowable adjacent channel interference

TX filter bandwidth

Peak carrier deviation (Modulation Index)

TX and RX carrier frequency accuracies

Modulator and Demodulator linearity

RX IF filter frequency and phase characteristics

Use of error correction techniques

Acceptable error-rate

As a guide to MOBITEX operation, a raw data-rate of 8kbps at 12.5kHz channel spacing may be achievable -

depending on local regulatory requirements- using a ±2kHz maximum deviation, a BT of 0.3, and no more

than 1.5kHz discrepancy between Tx & Rx carrier frequencies. Forward error correction (FEC) could then be

used with interleaving to reduce the effect of burst errors.

Reducing the data-rate to 4.8kbps would allow the BT to be increased to 0.5, improving the error-rate

performance.

5.1.2 FM Modulator, Demodulator and IF

For optimum performance, the eye pattern of the received signal (when receiving random data) applied to the

CMX589A should be as close as possible to the Transmit eye pattern examples shown in Figure 10.

Of particular importance are general symmetry, cleanliness of the zero-crossings, and for a BT of 0.3, the

relative amplitude of the inner eye opening.

To achieve this, attention must be paid to:

Linearity and frequency/phase response of the Tx frequency modulator. Unless the transmit data is

especially encoded to remove low frequency components, the modulator frequency response should

extend down to a few hertz. This is because two-point modulation is necessary for synthesized

radios.

Bandwidth & phase response of the RX IF filters.

Accuracy of the Tx and Rx carrier frequencies -any difference will shift the received signal towards

one of the skirts of the IF filter response.

High Speed GMSK Modem 16 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

Ideally, the Rx demodulator should be DC coupled to the CMX589A RX Signal In pin (with a DC bias added to

center the signal at the RX Feedback pin at VDD/2 [VBIAS]). However, AC coupling can be used provided that:

The 3dB cut-off frequency is 20Hz or below (i.e. a 0.1F capacitor in series with 100k).

The data does not contain long sequences of consecutive ones or zeroes.

Sufficient time is allowed after a step change at the discriminator output (resulting from channel

changing or the appearance of a RF carrier) for the voltage into the CMX589A to settle before the

RXDCacq line is strobed.

5.1.3 Two-Point Modulation

When designing the CMX589A into a radio that uses a frequency synthesizer, a two-point modulation

technique is recommended. This is both to prevent the radio's PLL circuitry from counteracting the

modulation process, and to provide a clean flat modulation response down to DC.

Figure 12 shows a suggested basic configuration to provide a two-point modulation drive from the CMX589A

TX Output using MX-COM's MX019 Digitally Controlled Quad Amplifier Array. The MX019 elements provide

individual set-up, calibration and dynamic control of modulation levels. Level setting control of the

amplifiers/attenuators of the MX019 is via an 8-bit data word. Note that the MX019 frequency response

supports data rates as high as 8kbps.

With reference to Figure 12:

The buffer amplifier is required to prevent loading of the CMX589A external RC circuit.

Stage B, with R1/R2, provides suitable signal and DC levels for the VCO varactor; C1 is RF

decoupling. The drive level should be adjusted (digitally) to provide the desired deviation.

Stage C, with R3/R4, provides the Reference Oscillator drive (application dependent). This

parameter is set by adjusting for minimum AC signal on the PLL control voltage with a low-frequency

modulating signal (inside the PLL bandwidth) applied.

Stage D could be used with the components shown if a negative reference drive is required.

Stage A provides buffering and overall level control.

CMX589A

TX OUT +14dB to -14dB

Buffer

+3dB to -3dB

CONTROL

+3dB to -3dB

TX VCO

To TX

REF Osc (+)

To TX

REF Osc (-)

V (-)

REF

External RC

See Fig.3

VCO

V(+)

REF

With reference to the MX019 Data Sheet

Stage A = MX019 Channel 4

Stage B = MX019 Channel 1

Stage C = MX019 Channel 2

Stage D = MX019 Channel 3

Note:

1. All stages of the MX019 are 'inverting' stages.

2. Components R1-R6 should produce the proper output

signal levels f or interface into the modulator.

Figure 12: An Example of Two-Point Modulation Drive with Individual Adjustment Using the MX019

High Speed GMSK Modem 17 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

5.2 AC Coupling of Tx and Rx Signals

In practical applications, it is possible to arrange AC coupling between the CMX589A Tx Output and the

frequency modulator to cut-off at a very low frequency, such as 5.0Hz. AC coupling between the receive

discriminator and the input of the CMX589A may need a shorter time-constant to avoid problems from voltage

steps at the output of the discriminator when changing channels or when the distant transmitter turns on.

For these reasons, as well as to maintain reasonable BER, the optimum –3dB cut-off frequencies are around

5.0Hz in the Tx path and 20.0Hz in the Rx path.

Figure 13 shows the typical static Bit-Error-Rate performance of the CMX589A operating under nominal

conditions for various degrees of AC coupling at the Rx input and the Tx output.

Data Rate = 8kbps VDD = 5.0V TAMB = 25C Tx BT = 0.3

S/N (dB) (noise in 8kHz bandwidth)

-5

-4

-3

-2

-1

45678910111213

BER

TX and RX DC coupled

TX 5Hz, RX DC coupled

TX 5Hz, RX 10Hz

TX 5Hz, RX 30Hz

TX 5Hz, RX 100Hz

Figure 13: Effect of AC Coupling on Typical Bit-Error Rate

Any AC Coupling at the receive input will transform any step in the voltage at the discriminator output to a

slowly decaying pulse which can confuse the modem’s level measuring circuits. As illustrated in Figure 14,

the time for this step to decay to 37% of its original value is ‘RC’ where:

network) RC the offrequency cutoff 3dB (the21

RC 



which is 32ms, or 256 bit times at 8kbps, for a 5Hz network.

Figure 14: Decay time-AC Coupling

High Speed GMSK Modem 18 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

6 Performance Specifications

6.1 Electrical Specifications

6.1.1 Absolute Maximum Limits

Exceeding these maximum ratings can result in damage to the device.

General Notes Min. Typ. Max. Units

Supply (VDD-VSS)-0.3 7.0 V

Voltage on any pin to VSS -0.3 VDD + 0.3 V

Current

VDD -30 30 mA

VSS -30 30 mA

Any other pin -20 20 mA

D2 / P4 Packages

Total allowable Power dissipation

at TAMB = 25C800 mW

Derating above 25C13 mW/C above 25C

Operating Temperature -40 85 C

Storage Temperature -55 125 C

D5 / E2 Packages

Total allowable Power dissipation

at TAMB = 25C550 mW

Derating above 25C9mW/C above 25C

Operating Temperature -40 85 C

Storage Temperature -55 125 C

Table 7: Absolute Maximum Ratings

6.1.2 Operating Limits

Correct Operation of the device outside these limits is not implied.

Notes Min. Typ. Max. Units

Supply (VDD-VSS)3.0 3.3/5.0 5.5 V

Operating Temperature -40 85 C

Rx and Tx Data Rate

VDD  3.0V 4 32 kbps

VDD  4.5V 4 200 kbps

Xtal Frequency

VDD  3.0V 1.0 5.0 MHz

VDD  4.5V 1.0 25.6 MHz

High Pulse Width 1 15 ns

Low Pulse Width 1 15 ns

Table 8: Operating Limits

Operating Limits Notes

1. Timing for an external clock input to the Xtal/Clock pin.

High Speed GMSK Modem 19 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

6.1.3 Operating Characteristics

For the following conditions unless otherwise specified.

VDD = 5.0V @ TAMB = 25C

Xtal/Clock Frequency = 4.096MHz, Data Rate = 8kbps, Noise Bandwidth = Bit Rate

Static Values Notes Min. Typ. Max. Units

Supply Current Tx PS Rx PS 1

IDD (VDD = 3.0V) 11 0.5 mA

01 1.0 mA

10 1.0 mA

00 1.5 mA

IDD (VDD = 5.0V) 11 1.0 mA

01 2.0 mA

10 3.0 mA

00 4.0 mA

Input Logic Level

Logic 1 Input Level 3.5 V

Logic 0 Input Level 1.5 V

Logic Input Current 2 -5.0 5.0 A

Output Logic Level

Logic 1 Output Level (IOH = 120A) 4.6 V

Logic 0 Output Level (IOL = -120A) 0.4 V

Transmit Parameters

Tx OUT pin DC bias shift caused by change from

Tx Enable = 0 to Tx Enable = 1 while

Tx PSAVE = 0 at 25C

-85 85 mV

Tx OUT, Output Impedance 3 1.0 k

Tx Out, Level 4, 10 0.8 1.0 1.2 VP-P

Output DC Offset 12 -0.125 0.125 V

Tx Data Delay

BT = 0.3 5 2.0 2.5 bit-

periods

BT = 0.5 5 1.5 2.0 bit-

periods

Tx PS to Output-Stable time 6 4.0 bit-

periods

Receive Parameters

Rx Amplifier

Input Impedance 1.0 M

Output Impedance 7 10.0 K

Voltage Gain 50.0 dB

Rx Filter Signal Input Level 8, 10 0.7 1.0 1.3 VP-P

Rx Time Delay 9 3.0 bit-

periods

High Speed GMSK Modem 20 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

Static Values Notes Min. Typ. Max. Units

On-Chip Xtal Oscillator

RIN 10.0 M

ROUT 11 50.0 k

Voltage Gain 11 25.0 dB

Table 9: Operating Characteristics

Operating Characteristics Notes:

1. Not including current drawn from the CMX589A pins by external circuitry. See Absolute Maximum

Ratings.

2. For VIN in the range VSS to VDD.

3. For a load of 10K or greater. Tx PS input at logic 0; Tx Enable = 1.

4. Data pattern of 1111000011110000…

5. Measured between the rising edge of Tx Clock and the center of the corresponding bit at Tx Out.

6. Time between the falling edge of the Tx PS and the Tx Out voltage stabilizing to normal output levels.

7. For a load of 10k or greater. Rx PS input at logic 0.

8. For optimum performance, Measured at the Rx Feedback pin for an 1111000011110000… pattern.

9. Measured between the center of bit at Rx Signal In and corresponding rising edge of the Rx Clock.

10. Levels are proportional to applied VDD

11. Small signal measurement at 1.0kHz with no load on Xtal output.

12. (Tx OUT enabled DC level) – (Tx Out disabled DC level) when transmitting a repeating 11110000 bit

pattern.

6.2 Packages

PIN 1

ALTERNATIVE

LOCATION

MARKING

0.303 (7.70)

PackageTolerances

TYP. MAX.MIN.

DIM.

0.047 (1.20)---------- 0.256 (6.50)

0° 8°

0.030 (0.75)

0.311 (7.90)

0.177 (4.50)

0.0256 (0.65)

0.020 (0.50)

0.248 (6.30) 0.006 (0.15)0.002 (0.05)

0.003 (0.08) 0.008 (0.20)

0.007 (0.17) 0.012 (0.30)

0.169 (4.30)

NOTE : All dimension s in inches (mm.)

Angles are in degrees

Figure 15: 24-pin TSSOP Mechanical Outline:

Order as part no. CMX589AE2

High Speed GMSK Modem 21 CMX589A PRELIMINARY INFORMATION

1998 MX-COM, Inc. www.mxcom.com Tele: 800 638 5577 336 744 5050 Fax: 336 744 5054 Doc. # 20480183.002

4800 Bethania Station Road, Winston-Salem, NC 27105-1201 USA All trademarks and service marks are held by their respective companies.

NOTE : All dimension s in inches (mm.)

Angles are in degrees

PackageTolerances

TYP. MAX.MIN.

DIM.

0.079 (2.00)0.066 (1.67) 0.312 (7.90)

0°

7°

4°

8°

9°

10°

0.037 (0.95)

0.328 (8.33)

0.213 (5.39)

0.026 (0.65)

0.022 (0.55)

0.301 (7.65) 0.008 (0.21)0.002 (0.05)

0.005 (0.13) 0.009 (0.22)

0.010 (0.25) 0.015 (0.38)

0.318 (8.07)

0.205 (5.20)

PIN 1

Figure 16: 24-pin SSOP Mechanical Outline:

Order as part no. CMX589AD5

0.597 (15.16)

PackageTolerances

TYP. MAX.MIN.DIM.

0.105 (2.67)

0.093 (2.36) 0.419 (10.64)

45°

7°

0° 10°

0.050 (1.27)

0.046 (1.17)

0.613 (15.57)

0.299 (7.59)

0.050 (1.27)

0.016 (0.41)

0.390 (9.90) 0.020 (0.51)0.003 (0.08)

0.009 (0.23) 0.0125 (0.32)

0.013 (0.33) 0.020 (0.51)

0.036 (0.91)

0.286 (7.26)

NOTE : All dimensions in inches (mm.)

Angles are in degrees

5°

PIN 1

ALTERNATIVE

LOCATION

MARKING

Figure 17: 24-pin SOIC Mechanical Outline:

Order as part no. CMX589AD2

NOTE : All dimension s in inches (mm.)

Angles are in degrees

PackageTolerances

TYP. MAX.MIN.DIM.

0.220 (5.59)

0.555 (14.04)

0.670 (17.02)

7°

0.160 (4.05)

1.270 (32.26)

0.151 (3.84)

0.100 (2.54)

0.121 (3.07)

0.600 (15.24)

0.590 (14.99) 0.625 (15.88)

0.015 (0.38) 0.045 (1.14)

0.008 (0.20) 0.015 (0.38)

0.015 (0.38) 0.023 (0.58)

0.040 (1.02) 0.065 (1.65)

0.066 (1.67) 0.074 (1.88)

1.200 (30.48)

0.500 (12.70)

J1J1

JJPP

PIN1PIN1 TT

E1E1

Figure 18: 24-pin PDIP Mechanical Outline:

Order as part no. CMX589AP4