PL IA N T Features M RoHS compliant* Suitable for most types of soldering *R oH S CO Power rating at 70 C: CR2010 - 1/2 W, CR2512 - 1 W Tight tolerances of bottom electrode width Three layer termination process with nickel barrier prevents leaching and provides excellent solderability processes Standard packaging on tape and reel AEC-Q200 approval upon request CR2010/CR2512 - Chip Resistors Derating Curve Characteristic Power Rating @ 70 C Operating Temperature Range Derated to 0 Load at Maximum Working Voltage Maximum Overload Voltage Resistance Range: 1 % E-96 + E-24 Model Model CR2010 CR2512 1/2 W 1W -55 C to +155 C +155 C 200 V 400 V 100 Rated Power (%) Electrical Characteristics 80 60 40 20 0 -55 1M ohms < R 10M ohms 200 PPM/C 10 ohms R 10M ohms 200 PPM/C 1 ohm R < 10 ohms 10M ohms < R 20M ohms 400 PPM/C Resistance Range: 5 % E-24 Zero Ohm Jumper <0.05 ohm Rated/Maximum Current 2 A/5 A 0 70 155 Ambient Temperature (C) 10 ohms R 1M ohms 100 PPM/C For Standard Values Used in Capacitors, Inductors, and Resistors, click here. Dimensional Drawing I1 I1 2 A/5 A H Chip Dimensions Dimension Model CR2010 5.00 0.20 (0.197 0.008) 2.50 0.20 (0.098 0.008) 0.60 0.10 (0.024 0.004) 0.60 0.25 (0.024 0.010) 0.60 0.25 (0.024 0.010) L W H I1 I2 Model CR2512 6.30 0.20 (0.248 0.008) 3.10 0.20 (0.122 0.008) 0.60 0.15 (0.024 0.006) 0.60 0.25 (0.024 0.010) 0.60 0.25 (0.024 0.010) I2 I2 W L DIMENSIONS: MM (INCHES) Performance Characteristics Test Thermal Shock Short Time Overload Resistance to Solder Heat Resistance to Dry Heat Load Life Load Life with Humidity Solderability Bending Dielectric Withstanding Voltage Insulation Resistance Procedure Method Test Limits R 1% 5% IEC60115-1-4.19 (0.5 % + 0.05 ) (1 % + 0.05 ) IEC60115-1-4.13 IEC60115-1-4.18 IEC60115-1-4.23.2 (1 % + 0.05 ) (0.5 % + 0.05 ) (1 % + 0.05 ) (1 % + 0.05 ) (2 % + 0.1 ) -55 for 30 minutes, +155 for 30 minutes, 5 cycles 2.5 X rated voltage for 5 seconds 270 5 for 10 1 seconds 125 5 for 96 4 hours Rated voltage for 1000 hours, 70 , 1.5 hours "ON", 0.5 hours "OFF" Rated voltage for 1000 hours, 40 2 , 90~95 % RH, 1.5 hours "ON", 0.5 hours "OFF" 245 5 , 2 0.5 seconds 3 mm IEC60115-1-4.17 IEC60115-1-4.33 95 % of area covered (0.5 % + 0.05 ) (1 % + 0.05 ) -- IEC60115-1-4.7 >500 V 100 V IEC60115-1-4.6 1 G IEC60115-1-4.25.1 (1 % + 0.05 ) (3 % + 0.1 ) IEC60115-1-4.24 (1 % + 0.05 ) (3 % + 0.1 ) *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. CR2010/CR2512 - Chip Resistors How to Order CR 2010 - F X - 8252 E LF Model (CR = Chip Resistor) Size * 2010 * 2512 Resistance Tolerance F = 1 % .............. Use with "X" TCR code only for values from 10 ohms through 1 megohm; Use with "W" TCR code only for values from 1 megohm through 10 megohms J = 5 % .................Use with "W" TCR code for values from 10 ohms through 10 megohms; Use with "Z" TCR code for values above 10 megohms through 20 megohms; Use with "/" TCR code for zero ohm (jumper) and values from 1 ohm through 9.1 ohms. TCR (ppm/C) X = 100 W = 200 Z = 400 / = Used with "J" Resistance Tolerance code for zero ohm (jumper) and values from 1 ohm through 9.1 ohms. Resistance Value For 1 % Tolerance: <100 ohms..............."R" represents decimal point (example: 24R3 = 24.3 ohms) 100 ohms...............First three digits are significant, fourth digit represents number of zeros to follow (example: 8252 = 82.5k W) For 5 % Tolerance: <10 ohms .............. "R" represents decimal point (example: 4R7 = 4.7 ohms) 10 ohms............... First two digits are significant, third digit represents number of zeros to follow (example: 474 = 470k ohms; 000 = Jumper) Packaging E = Embossed Plastic Tape (4,000 pcs.) on 7 " Plastic Reel Termination LF = Tin-plated (RoHS compliant) Soldering Profile for RoHS Compliant Chip Resistors and Arrays Marking Explanation 275 <1> Maximum of 20 seconds between Resistors with 5 % tolerance may have a 3-digit or 4-digit resistance code. Complete information about resistance value and tolerance is found on the label of the reel of chip resistors. * 5 %: 3 digits, first two digits are significant, third digit is number of zeros to follow. Letter R is decimal point for values from 1 to 9.9 ohms. * 5 %: 4 digits, first three digits are significant, fourth digit is number of zeros to follow. Letter R is decimal point for values from 1 to 99.9 ohms. * 1 %: 4 digits, first three digits are significant, fourth digit is number of zeros to follow. Letter R is decimal for values from 1 to 99.9 ohms. 260 C peak +255 C and +260 C <1> 255 C 225 Temperature (C) 220 C 190 C 175 60 - 90 seconds Ramp Down 6 C/second 150 C 125 60 - 120 seconds 10 seconds minimum 75 Ramp Up 3 C/second maximum 25 0 50 100 150 Time (seconds) 200 250 300 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. 3312 - 2 mm SMD CR2010/CR2512 - Chip Trimming Resistors Potentiometer Packaging Dimensions 4.0 0.1 (.157 .004) Model CR2010 2.8 0.2 (0.110 0.008) 5.5 0.2 (0.217 0.008) 12.0 0.3 (0.472 0.012) 5.5 0.05 (0.217 0.002) 4.0 0.1 (0.157 0.004) Dimension 2.0 0.05 (.079 .002) A B A F B W W P0 1.5 +0.1/-0 (.056 + .004/-0) 1.75 0.1 (.059 .004) F P0 DIMENSIONS: Model CR2512 3.5 0.2 (0.138 0.008) 6.7 0.2 (0.264 0.008) 12.0 0.3 (0.472 0.012) 5.5 0.05 (0.217 0.002) 4.0 0.1 (0.157 0.004) MM (INCHES) 2.0 0.5 (.080 .020) 13.0 0.5 (.512 .020) 80.0 0.5 (3.150 .020) 20.0 MIN. (.787) 178.0 2.0 (7.008 .080) 16.7 MAX. (.657) REV. 07/15 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Bourns: CR2010-FW-R050ELF CR2010-FX-10R0ELF CR2010-FX-2260ELF CR2010-FX-30R1ELF CR2010-FX-33R0ELF CR2010-FX-45R3ELF CR2010-FX-47R0ELF CR2010-FX-53R6ELF CR2010-FX-7501ELF CR2010-FX-93R1ELF CR2010-J/-000ELF CR2010-J/-1R0ELF CR2010-J/-1R2ELF CR2010-J/-1R3ELF CR2010-J/-2R4ELF CR2010-J/5R6ELF CR2010-JW-100ELF CR2010-JW-101ELF CR2010-JW-102ELF CR2010-JW-103ELF CR2010-JW-104ELF CR2010-JW-113ELF CR2010-JW-134ELF CR2010-JW-184ELF CR2010-JW-202ELF CR2010-JW-220ELF CR2010-JW-221ELF CR2010-JW-222ELF CR2010-JW-240ELF CR2010-JW-270ELF CR2010-JW-331ELF CR2010JW-332ELF CR2010-JW-390ELF CR2010-JW-514ELF CR2010-JW-562ELF CR2010-JW-624ELF CR2010-JW683ELF CR2010-JW-820ELF CR2010-JW-821ELF CR2010-JW-824ELF CR2512-JW-101ELF CR2512-JW-102ELF CR2512-JW-103ELF CR2512-JW-122ELF CR2512-JW-201ELF CR2512-JW-222ELF CR2512-JW-431ELF CR2512JW-470ELF CR2512-JW-510ELF CR2512-JW-511ELF CR2512-JW-682ELF CR2512-JW-912ELF CR2010-FX1000ELF CR2010-FX-1071ELF CR2010-FX-1500ELF CR2512-J/-000ELF CR2010-FX-20R0ELF CR2010-FX2491ELF CR2010-FX-2550ELF CR2010-FX-2551ELF CR2010-FX-3241ELF CR2010-FX-3570ELF CR2010-FX3651ELF CR2010-FX-5100ELF CR2010-FX-51R1ELF CR2010-FX-62R0ELF CR2010-FX-66R5ELF CR2010-FX73R2ELF CR2010-J/-2R2ELF CR2010-J/-3R3ELF CR2010-JW-150ELF CR2010-JW-151ELF CR2010-JW-181ELF CR2010-JW-183ELF CR2010-JW-242ELF CR2010-JW-301ELF CR2010-JW-303ELF CR2010-JW-330ELF CR2010JW-391ELF CR2010-JW-431ELF CR2010-JW-680ELF CR2010-JW-750ELF CR2010-JW-911ELF CR2512-FX10R0ELF CR2512-FX-1100ELF CR2512-FX-1210ELF CR2512-FX-1272ELF CR2512-FX-1500ELF CR2512-FX1501ELF CR2512-FX-1783ELF CR2512-FX-2371ELF CR2512-FX-2490ELF CR2512-FX-2492ELF CR2512-FX3001ELF CR2512-FX-3301ELF CR2512-FX-49R9ELF CR2512-FX-6801ELF CR2512-FX-75R0ELF CR2512-FX8200ELF CR2512-FX-82R5ELF