800 MHz, Linear-in-dB VGA with AGC Detector AD8368 Analog variable gain range: -12 dB to +22 dB Linear-in-dB scaling: 37.5 dB/V 3 dB bandwidth: 800 MHz @ VGAIN = 0.5 V Integrated rms detector P1dB: 16 dBm @ 140 MHz Output IP3: 33 dBm @ 140 MHz Noise figure at maximum gain: 9.5 dB @ 140 MHz Input and output impedances: 50 Single-supply voltage from 4.5 V to 5.5 V RoHS-compliant, 24-lead LFCSP FUNCTIONAL BLOCK DIAGRAM VPSO MODE 10 21 VPSO VPSI VPSI VPSI VPSI VPSI 9 11 12 22 ICOM 16 GAIN INTERPOLATOR FIXED-GAIN AMPLIFIER OCOM 7 OUTPUT BUFFER gm STAGES 0dB -2dB -4dB -36dB REF INPT 19 ICOM 17 ICOM 18 24 ENBL 8 OUTP 3 HPFL 4 DECL 14 DECL 50 DECL ATTENUATOR LADDER - X2 15 DECL + ICOM 20 APPLICATIONS Complete IF AGC amplifiers Gain trimming and leveling Cellular base stations Point-to-point radio links RF instrumentation 13 AD8368 OCOM 6 GAIN 1 23 2 5 DETO DETI 05907-001 FEATURES Figure 1. GENERAL DESCRIPTION The AD8368 is a variable gain amplifier (VGA) with analog linear-in-dB gain control that can be used from low frequencies to 800 MHz. Its excellent gain range, conformance, and flatness are attributed to the Analog Devices, Inc., X-AMP(R) architecture, an innovative technique for implementing high performance variable gain control. The gain range of -12 dB to +22 dB is scaled accurately to 37.5 dB/V with excellent conformance error. The AD8368 has a 3 dB bandwidth of 800 MHz that is nominally independent of gain setting. At 140 MHz, the OIP3 is 33 dBm at maximum gain. The output noise floor is -143 dBm/Hz, which corresponds to a 9.5 dB noise figure at maximum gain. The single-ended input and output impedances are nominally 50 . The gain of the AD8368 can be configured to be an increasing or decreasing function of the gain control voltage depending on whether the MODE pin is pulled to the positive supply or to ground, respectively. When MODE is pulled high, the AD8368 operates as a typical VGA with increasing gain. By connecting MODE to ground and using the on-board rms detector, the AD8368 can be configured as a complete automatic gain control (AGC) system with RSSI. The output power is accurately leveled to the internal default setpoint of 63 mV rms (-11 dBm referenced to 50 ), independent of the waveform crest factor. Because the uncommitted detector input is available at DETI, the AGC loop can level the signal at the AD8368 output or at any other point in the signal chain over a maximum input power range of 34 dB. Furthermore, the setpoint level can be raised by dividing down the output signal before applying it to the detector. The AD8368 operates from a supply voltage of 4.5 V to 5.5 V and consumes 60 mA of current. It can be fully powered down to <3 mA by grounding the ENBL pin. The AD8368 is fabricated using the Analog Devices proprietary SiGe SOI complementary bipolar IC process. It is available in a 24-lead LFCSP and operates over the industrial temperature range of -40C to +85C. Application boards are available upon request. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006-2008 Analog Devices, Inc. All rights reserved. AD8368 TABLE OF CONTENTS Features ............................................................................................ 1 Fixed-Gain Stage and Output Buffer ..................................... 12 Applications ..................................................................................... 1 Output Offset Correction........................................................ 12 Functional Block Diagram ............................................................ 1 Input and Output Impedances ............................................... 12 General Description ....................................................................... 1 Gain Control Interface ............................................................ 13 Revision History ............................................................................. 2 Applications Information ............................................................ 14 Specifications................................................................................... 3 VGA Operation ........................................................................ 14 Absolute Maximum Ratings.......................................................... 5 AGC Operation ........................................................................ 14 ESD Caution ................................................................................ 5 Stability and Layout Considerations ...................................... 16 Pin Configuration and Function Descriptions ........................... 6 Evaluation Board .......................................................................... 17 Typical Performance Characteristics ........................................... 7 Outline Dimensions ..................................................................... 19 Circuit Description ....................................................................... 12 Ordering Guide ........................................................................ 19 Input Attenuator and Interpolator ......................................... 12 REVISION HISTORY 9/08--Rev. A to Rev. B Added Stability and Layout Considerations Section ................. 16 Changes to Evaluation Board Section, Figure 40, and Table 6 .............................................................................................. 17 Added Figure 41, Figure 42, Figure 43, and Figure 44; Renumbered Sequentially.............................................................. 18 Added Exposed Pad Notation to Outline Dimensions ............. 19 4/06--Revision 0: Initial Version 10/07--Rev. 0 to Rev. A Changes to Table 1 ............................................................................ 3 Changes to Figure 4 to Figure 6 ...................................................... 7 Changes to Figure 16 ........................................................................ 9 Changes to Figure 31 ...................................................................... 12 Updated Outline Dimensions ....................................................... 18 Changes to Ordering Guide .......................................................... 18 Rev. B | Page 2 of 20 AD8368 SPECIFICATIONS VS = 5 V, TA = 25C, system impedance Z0 = 50 , VMODE = 5 V, RF input = 140 MHz, unless otherwise noted. Table 1. Parameter OVERALL FUNCTION Frequency Range Maximum Input Maximum Output 1 AC Input Impedance AC Output Impedance GAIN CONTROL INTERFACE (GAIN) Gain Span Gain Scaling Gain Accuracy Maximum Gain Minimum Gain VGAIN Range Gain Step Response Gain Input Bias Current f = 70 MHz Noise Figure Output IP3 Output P1dB1 f = 140 MHz Noise Figure Output IP3 Output P1dB1 f = 240 MHz Noise Figure Output IP3 Output P1dB1 f = 380 MHz Noise Figure Output IP3 Output P1dB1 1 Min Typ LF Max Unit Conditions 800 MHz VP VP 3 dB bandwidth To avoid input overload To avoid clipping From INPT to ICOM From OUTP to OCOM 3 2 50 50 34 37.5 -38 0.4 22 -12 0 1 100 -2 dB dB/V dB/V dB dB dB V ns A VMODE = 5 V, 50 mV VGAIN 950 mV VMODE = 0 V, 50 mV VGAIN 950 mV 100 mV VGAIN 900 mV VGAIN = 1 V VGAIN = 0 V For 6 dB gain step 9.5 34 16 dB dBm dBm Maximum gain f1 = 70 MHz, f2 = 71 MHz, VGAIN = 1 V, 0 dBm per output tone VGAIN = 0 V, VMODE = 0 V 9.5 33 16 dB dBm dBm Maximum gain f1 = 140 MHz, f2 = 141 MHz, VGAIN = 1 V, 0 dBm per output tone VGAIN = 0 V, VMODE = 0 V 9.7 33 15 dB dBm dBm Maximum gain f1 = 240 MHz, f2 = 241 MHz, VGAIN = 1 V, 0 dBm per output tone VGAIN = 0 V, VMODE = 0 V 10 29 13 dB dBm dBm Maximum gain f1 = 380 MHz, f2 = 381 MHz, VGAIN = 1 V, 0 dBm per output tone VGAIN = 0 V, VMODE = 0 V Operation at compression is not recommended due to adverse distortion components. Rev. B | Page 3 of 20 AD8368 VS = 5 V, TA = 25C, system impedance Z0 = 50 , VMODE = 5 V, RF input = 140 MHz, unless otherwise noted. Table 2. Parameter SQUARE LAW DETECTOR (DETI, DETO) Output Setpoint DETI DC Bias Level to ICOM DETI Impedance Min DETO Output Range 1 AGC Step Response MODE CONTROL INTERFACE (MODE) MODE Threshold MODE Input Bias Current POWER INTERFACE (VPSI, VPSO) Supply Voltage Total Supply Current Disable Current ENABLE INTERFACE (ENBL) Enable Threshold Enable Response Time 0.1 ENBL Input Bias Current 1 Typ Max -11 VS/2 710 0.6 VS/2 30 3.5 50 4.5 5 60 2 5.5 Unit Conditions dBm V pF V s OUTP connected to DETI V A V mA mA 2.5 1.5 V s 3 s 150 For -6 dB input power step (CDETO = 1 nF) A Refer to AGC Operation section. Rev. B | Page 4 of 20 ENBL high ENBL low Time delay following off-to-on transition until output reaches 90% of final value Time delay following on-to-off transition until supply current is less than 5 mA VENBL = 5 V AD8368 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Supply Voltage (VPSO, VPSI) ENBL and MODE Select Voltage RF Input Level Internal Power Dissipation JA Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering, 60 sec) Rating 5.5 V 5.5 V 20 dBm 440 mW 52C/W 125C -40C to +85C -65C to +150C 300C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. B | Page 5 of 20 AD8368 ENBL VPSI VPSI MODE ICOM INPT PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 24 23 22 21 20 19 GAIN 1 18 ICOM DETO 2 17 ICOM HPFL 3 AD8368 16 ICOM DECL 4 TOP VIEW (Not to Scale) 15 DECL DETI 5 14 DECL 9 10 11 12 VPSI VPSI NOTES 1. EXPOSED PAD. CONNECT EPAD TO LOW IMPEDANCE GROUND. 05907-002 8 VPSO OCOM 7 VPSO 13 VPSI OUTP OCOM 6 Figure 2. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 2 3 Mnemonic GAIN DETO HPFL 4, 14, 15 DECL 5 6, 7 8 9, 10 DETI OCOM OUTP VPSO 11, 12, 13, 22, 23 VPSI 16, 17, 18, 20 19 21 24 ICOM INPT MODE ENBL EPAD Description Gain Control. Detector Output. Provides an output error current for the AGC function. High-Pass Filter Connection. A capacitor to ground sets the corner frequency of the internal output offset control loop that controls the minimum usable input frequency. Decoupling Pin. Nominally ~VS/2. Decoupling capacitance may need to be adjusted for AGC operation (see the Applications Information section). Detector Input. DC level referenced to DECL pin. Connect OCOM to low impedance ground. Signal Output. Must be ac-coupled. Positive Supply Voltage, 4.5 V to 5.5 V. VPSO and VPSI must be connected together externally and properly bypassed. Positive Supply Voltage, 4.5 V to 5.5 V. VPSO and VPSI must be connected together externally and properly bypassed. Connect ICOM to low impedance ground. Signal Input. Must be ac-coupled. Gain Direction Control. High for positive slope. Low for negative slope. Apply a Positive Voltage (2.5 V VENBL VPSI) to Activate Device. Exposed Pad. Connect the exposed pad to low impedance ground. Rev. B | Page 6 of 20 AD8368 TYPICAL PERFORMANCE CHARACTERISTICS VS = 5 V, T = 25C, system impedance Z0 = 50 , MODE = 5 V, unless otherwise noted. 25 25 4 240MHz 20 15 0.75V 10 1 5 0 0 -1 +25C 0.25V -40C -5 -10 100 -15 1000 -3 0 0.2 0.4 FREQUENCY (MHz) 0.6 VGAIN (V) Figure 3. S21 vs. Frequency by VGAIN Figure 6. Gain and Conformance Error vs. VGAIN (f = 240 MHz) 4 25 25 4 70MHz 380MHz 3 10 1 5 0 -1 +25C -40C -5 -2 -10 -3 -15 0 0.2 0.4 0.6 -4 1.0 0.8 3 15 GAIN (dB) GAIN (dB) +85C CONFORMANCE ERROR (dB) 2 15 20 2 +85C 10 1 5 0 0 -1 +25C -40C -5 -2 -10 05907-004 20 0 -4 1.0 0.8 -15 CONFORMANCE ERROR (dB) -20 10 -10 05907-003 0V -15 -2 05907-006 GAIN (dB) S21 (dB) 0.5V 0 -5 2 +85C 10 5 3 CONFORMANCE ERROR (dB) 1V 15 -3 0 0.2 0.4 VGAIN (V) 0.6 05907-007 20 -4 1.0 0.8 VGAIN (V) Figure 4. Gain and Conformance Error vs. VGAIN (f = 70 MHz) 25 Figure 7. Gain and Conformance Error vs. VGAIN (f = 380 MHz) 4 0.7 140MHz 20 3 15 2 0.6 5 0 0 -1 +25C -40C -5 -2 -10 -3 -15 0 0.2 0.4 0.6 0.8 -4 1.0 VGAIN (V) 0.3 0.2 VOUTP 0.1 0 -0.1 -0.2 05907-008 1 VGAIN 0.4 AMPLITUDE (V) 10 05907-005 GAIN (dB) +85C CONFORMANCE ERROR (dB) 0.5 -0.3 -0.4 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 TIME (s) Figure 8. Gain Step Time Domain Response (6 dB Gain Step) Figure 5. Gain and Conformance Error vs. VGAIN (f = 140 MHz) Rev. B | Page 7 of 20 0.5 AD8368 20 +85C +25C -40C 20 15 10 5 0 70 110 150 190 230 270 310 350 +25C 16 14 12 10 -40C 8 6 4 05907-012 OUTPUT 1dB COMPRESSION (dBm) 30 25 +85C 18 35 05907-009 OUTPUT THIRD-ORDER INTERCEPT (dBm) 40 2 0 70 380 110 150 RF INPUT (MHz) 70MHz 140MHz 350 380 240MHz 380MHz 20 15 10 5 0 0.2 0.4 0.6 0.8 16 14 380MHz 12 240MHz 10 8 6 4 05907-013 OUTPUT 1dB COMPRESSION (dBm) 30 25 140MHz 18 35 05907-010 OUTPUT THIRD-ORDER INTERCEPT (dBm) 310 20 70MHz 2 0 1.0 0 0.2 0.4 VGAIN (V) 0.6 0.8 1.0 VGAIN (V) Figure 13. Output 1dB Compression Point vs. VGAIN (VMODE = 0 V) Figure 10. Output Third-Order Intercept vs. VGAIN (VMODE = 0 V) 20 0 5.5V 18 -20 -30 -40 380MHz 240MHz -50 -70 140MHz 0 0.2 0.4 0.6 70MHz 0.8 05907-011 -60 16 14 5.0V 12 4.5V 10 8 6 4 05907-014 OUTPUT 1dB COMPRESSION (dBm) -10 THIRD-ORDER IMD (dBc) 270 Figure 12. Output 1dB Compression Point vs. RF Input Frequency at Maximum Gain (VMODE = 0 V) 40 -80 230 RF INPUT (MHz) Figure 9. Output Third-Order Intercept vs. RF Input Frequency at Maximum Gain (VMODE = 0 V) 0 190 2 0 70 1.0 VGAIN (V) 110 150 190 230 270 310 350 380 RF INPUT (MHz) Figure 14. Output 1dB Compression Point vs. RF Input Frequency by Supply Voltage at Maximum Gain (VMODE = 0 V) Figure 11. Third-Order IMD vs. VGAIN (Output Power = 0 dBm per Tone, VMODE = 0 V) Rev. B | Page 8 of 20 AD8368 50 45 35 VGAIN = 0.75V 30 25 VGAIN = 0V 20 VGAIN = 1V 15 VGAIN = 0.25V 10 VGAIN = 0.5V 0 10 100 05907-018 05907-015 5 1000 FREQUENCY (MHz) Figure 15. Noise Figure vs. Frequency at Maximum Gain (VMODE = 0 V) Figure 18. Input Reflection Coefficient vs. Frequency 50 0 45 -5 OUTPUT RETURN LOSS (dB) 35 30 25 20 15 70MHz 140MHz 240MHz 380MHz 10 5 0 0 0.2 0.4 0.6 0.8 -10 -15 -20 -25 -30 -35 05907-016 NOISE FIGURE (dB) 40 VGAIN = 1V VGAIN = 0V -40 10 1.0 100 VGAIN (V) 1000 FREQUENCY (MHz) Figure 16. Noise Figure vs. VGAIN (VMODE = 0 V) Figure 19. Output Return Loss vs. Frequency 0 -5 VGAIN = 0.75V -15 VGAIN = 1V VGAIN = 1V -25 -30 VGAIN = 0V VGAIN = 0V VGAIN = 0.25V -40 10 100 05907-020 -35 05907-017 INPUT RETURN LOSS (dB) VGAIN = 0.5V -10 -20 1000 FREQUENCY (MHz) Figure 20. Output Reflection Coefficient vs. Frequency Figure 17. Input Return Loss vs. Frequency Rev. B | Page 9 of 20 05907-019 NOISE FIGURE (dB) 40 1.0 0.9 0.8 0.9 0.8 0.8 0.6 0.8 0.4 0.6 0.2 0.5 0 -0.2 +25C -0.4 +25C 0.2 -0.6 0.1 -0.8 -40C -35 +85C -30 -25 -20 -15 -10 -5 0 5 -1.0 0.6 0.2 0.5 0 -40C 0.4 0.2 -0.6 0.1 -0.8 0 -40 +25C +85C -35 -30 -25 0.4 0.6 0.2 0.5 0 +25C +85C -0.2 -40C -0.4 -40C 0.2 -0.6 0.1 -0.8 +85C -25 -20 -15 -10 -5 0 5 -1.0 0.8 0.8 0.6 0.7 0.4 0.6 0.2 0.5 0 +25C +85C -0.2 -40C -0.4 -40C 0.2 -0.6 0.1 0 -40 -0.8 -35 +85C -30 -25 -20 -15 -10 -5 0 5 -1.0 SUPPLY CURRENT (mA) 1.0 0.9 CONFORMANCE ERROR (dB) 1.0 +25C -1.0 410mV Figure 25. AGC Time Domain Response (3 dB Power Step, CDETO = 1 nF) 05907-023 RSSI (V) Figure 22. RSSI (VDETO) and Conformance Error vs. Input Power (f = 140 MHz) 0.3 5 VOUTP CH2 50mV CH3 100mV M20s 500MS/s A CH1 2.0ns/PT RF INPUT (dBm) 0.4 0 05907-025 0.6 0.7 -30 -5 VRSSI AMPLITUDE (V) 0.8 -35 -10 Figure 24. RSSI (VDETO) and Conformance Error vs. Input Power (f = 380 MHz) CONFORMANCE ERROR (dB) 0.8 0 -40 -15 05907-022 RSSI (V) 1.0 0.9 +25C -20 RF INPUT (dBm) 1.0 0.3 -0.4 -40C RF INPUT (dBm) Figure 21. RSSI (VDETO) and Conformance Error vs. Input Power (f = 70 MHz) 0.4 -0.2 +25C 0.3 RF INPUT (dBm) 80 8 70 7 60 4.5V 6 50 40 5 5.0V 5.5V 5.5V 4 30 3 5.0V 20 2 10 1 4.5V 0 -40 -20 0 20 40 60 80 0 TEMPERATURE (C) Figure 23. RSSI (VDETO) and Conformance Error vs. Input Power (f = 240 MHz) Rev. B | Page 10 of 20 Figure 26. Supply Current and Disable Current vs. Temperature DISABLE CURRENT (mA) 0 -40 0.4 05907-026 0.4 0.3 -40C +85C 0.7 RSSI (V) 0.7 0.6 +85C CONFORMANCE ERROR (dB) 1.0 05907-024 1.0 CONFORMANCE ERROR (dB) 1.0 05907-021 RSSI (V) AD8368 AD8368 50 VENBL PERCENTAGE (%) AMPLITUDE (V) 40 VOUTP 30 20 CH2 500mV CH3 5V M2.0s 250MS/s 4.0ns/PT A CH3 0 0.0V 30 20 10 05907-028 PERCENTAGE (%) 40 37.2 37.4 37.6 -14.7 -14.4 -14.1 -13.8 -13.5 Figure 29. Gain Intercept Distribution (140 MHz) 50 37.0 -15.0 INTERCEPT (dB) Figure 27. ENBL Response Time 0 36.8 05907-029 05907-027 10 37.8 38.0 38.2 SLOPE (dB/V) Figure 28. Gain Scaling Distribution (140 MHz) Rev. B | Page 11 of 20 AD8368 CIRCUIT DESCRIPTION The main signal path, shown in Figure 30, consists of a variable input attenuator followed by a fixed-gain amplifier and output buffer. This architecture allows for a constant OIP3 and output noise floor as a function of gain setting. As a result, NF and IIP3 increase 1 dB for every 1 dB decrease in gain, resulting in a part with constant dynamic range over gain setting. OUTPUT OFFSET CORRECTION The dc level at the input, INPT, is driven by an internal reference to VS/2. The reference is made available at the DECL pin for external decoupling with CDECL. The dc level at the output, OUTP, is regulated to the same midsupply reference by an offset correction loop independent of gain setting, temperature, and process. The low-pass response of this loop creates a high-pass corner frequency in the signal path transfer function, which can be set by choosing CDECL and CHPFL. FIXED-GAIN OUTPUT AMPLIFIER BUFFER FROM INTERPOLATOR gm STAGES gm x1 MODE GAIN GAIN INTERPOLATOR FIXED-GAIN OUTPUT AMPLIFIER BUFFER gm STAGES 0dB -2dB -4dB -36dB 05907-033 50 DECL ATTENUATOR LADDER Figure 30. Simplified Block Diagram INPUT ATTENUATOR AND INTERPOLATOR The input attenuator is built from an 18-section resistor ladder, providing 2 dB of attenuation at each successive tap point. The resistor ladder acts as a linear input attenuator, in addition to providing an accurate 50 input impedance. The variable transconductance (gm) stages are used to select the attenuated signal from the appropriate tap point along the ladder and feed this signal to the fixed-gain amplifier. To realize a continuous gain control function from discrete tap points, the gain interpolator creates a weighted sum of signals appearing on adjacent tap points by carefully controlling the variable gm stages. FIXED-GAIN STAGE AND OUTPUT BUFFER The weighted sum of the different tap points is fed into the fixed-gain stage that drives the output buffer. Because the resistive input attenuator is linear and contributes minimal noise as a passive termination, the dynamic range as a function of gain is determined primarily by the noise and the distortion of the fixed-gain amplifier. This architecture explains the constant OIP3 and constant output noise floor with gain setting and the corresponding dB-for-dB increase in IIP3 and NF with decreasing gain. The output buffer has 6 dB of gain and provides a broadband 50 single-ended output impedance. HPFL DECL CHPFL CDECL VMID Figure 31. Output Centering Control Loop VOUT INPT VOUT 05907-034 The AD8368 is a single-ended VGA with a bandwidth of 800 MHz and a gain control span of 34 dB ranging from -12 dB to +22 dB. It incorporates an uncommitted square law detector that can be used to form a tight AGC loop around the VGA. Using the Analog Devices patented X-AMP architecture, the AD8368 achieves accurate linear-in-dB gain control with excellent linearity (OIP3) and noise figure (NF). The part also features 50 input and output impedances for ease of use. The input and output coupling capacitors should be selected to provide low impedances at the frequencies of interest relative to 50 so as not to affect the high-pass corner. In this case, the high-pass corner frequency can be set by either CHPFL or CDECL, which form independent poles in the feedback path of the offset correction loop. The high-pass corner is determined by the highest of these poles, which are given by fHP , HPFL (kHz) = 0.8 (0.005 + CHPFL) fHP , DECL (kHz) = 5700 (0.005 + CDECL) where CHPFL and CDECL are in nF. When using this method to set the high-pass frequency, the other capacitor should be sized such that its pole is at least 30x lower in frequency. In addition, note that CDECL represents the total decoupling capacitance at the DECL pins. INPUT AND OUTPUT IMPEDANCES The AD8368 offers single-ended broadband 50 input and output impedances. The excellent match to 50 is maintained from part to part, over frequency, and over gain setting. Both the input and output pins must be externally ac-coupled to prevent disruption of the internal dc levels. Sufficiently large coupling capacitors should be used so that their impedance is negligible relative to the 50 presented by the ladder at the input and by the output buffer at the output. Rev. B | Page 12 of 20 AD8368 4 GAIN CONTROL INTERFACE 25 The AD8368 has a linear-in-dB gain control interface that can be operated in either a gain-up mode or gain-down mode. In the gain-up mode with the MODE pin pulled high, the gain increases with increasing gain voltages. In the gain-down mode, with the MODE pin pulled low, the gain decreases with increasing gain voltages. In both modes of operation, the gain control slope is maintained at +37.5 dB/V or -38 dB/V (depending on mode selection) over temperature, supply, and process as VGAIN varies from 100 mV to 900 mV. To form an AGC loop with the on-board detector around the VGA, the MODE pin has to be pulled low. 20 3 15 2 GainLOW (dB) = -38 x VGAIN + 24.8 where VGAIN is expressed in volts. 1 0 5 0 ERROR_H -1 -2 -5 -3 -10 GAIN_L -15 The gain functions for MODE pulled high and low are given respectively by GainHIGH (dB) = 37.5 x VGAIN - 14 ERROR_L 0 0.2 0.4 0.6 0.8 -4 1.0 VGAIN (V) Figure 32. Gain and Conformance Error vs. VGAIN As shown in Figure 32, the gain function can be either an increasing or decreasing function of VGAIN, depending on the MODE pin. Rev. B | Page 13 of 20 05907-035 GAIN (dB) 10 CONFORMANCE ERROR (dB) GAIN_H AD8368 APPLICATIONS INFORMATION VGA OPERATION The AD8368 is a general-purpose VGA suitable for use in a wide variety of applications where accurate, continuous, linear-in-dB gain control over a broad range of frequencies is important. Its stability over temperature and supply in comparison to other variable gain techniques can be traced back to the X-AMP architecture. While having an 800 MHz bandwidth, its low frequency operation can be extended by properly selecting CHPFL and CDECL. The typical connections for using the AD8368 in VGA mode are illustrated in Figure 33. The input (INPT) and output (OUTP) of the AD8368 should be externally ac-coupled to prevent disrupting the dc levels on the chip. Therefore, a sufficiently large coupling capacitor should be used such that the series impedance of the capacitor is negligible at the frequencies of interest. VIN INPT VPSI CDETO R2 INPT ICOM X2 DECL ICOM REF - DECL + DECL VPSI VPSI VPSI VPSO AD8368 OCOM OCOM R1 Figure 33. Typical Connections for VGA Mode for Increasing Gain with Increasing VGAIN (MODE High) The gain control voltage ranging from 0 V to 1 V is applied to the GAIN pin. The MODE pin controls whether the gain of the part is an increasing or decreasing function of the gain voltage. When the MODE pin is pulled high, the gain increases with increasing gain voltages. When the MODE pin is pulled low, the gain decreases with increasing gain voltages. The ENBL pin is used to enable or disable the part. ENBL is active high; when ENBL is pulled low, the part is disabled and draws a fraction of the normal supply current. ICOM DETO DETI 05907-036 VPOS VOUT ICOM HPFL VPSI VPSI VPSO OUTP OCOM VPSO AD8368 OCOM GAIN VPOS VOUT 05907-037 RSSI DECL MODE DECL + DETI VPSI ICOM REF - ENBL DECL VPOS VPSI ICOM VPSO DETO OUTP ICOM MODE VPSI VPSI ENBL ICOM X2 The AD8368 can be configured as a standalone AGC amplifier by using the on-board rms detector, as shown in Figure 34. The detector output, DETO, is an error current representing the difference of squares between the root-mean-square (rms) of the sensed signal and an internal reference of 63 mV rms. This error current is integrated on CDETO and connected to the GAIN pin to form the AGC loop. VIN GAIN HPFL AGC OPERATION The 63 mV rms reference corresponds to 178 mV p-p for a sine wave but the detector accuracy is maintained for more complex signals, such as Gaussian noise, complex envelopes, and multicarrier signals with high peak-to-average ratios. VPOS VGAIN 0V TO 1V The DECL pin provides the internal midsupply dc reference for the AD8368. It should be well decoupled to ground using a large capacitor with low ESR. The capacitors connected to the HPFL pin and DECL pin are used to control the low-pass corner frequency of the output offset correction loop. The resulting high-pass corner frequency is inversely proportional to their values. Figure 34. AGC Mode of Operation The AGC mode of operation requires a specific gain direction. The gain must fall as VDETO increases to restore the needed balance against the setpoint. Therefore, the MODE pin must be pulled low. By connecting the signal at OUTP directly to the detector input (DETI), the output level is driven to the 63 mV rms reference setpoint. Rev. B | Page 14 of 20 AD8368 Figure 36 shows a plot of the RSSI voltage at DETO as input power is swept. 3.0 2.5 2.0 RSSI (V) The output setpoint can be increased using an external resistive divider network between OUTP and DETI, referenced to DECL as depicted in Figure 34. In this configuration, the rms output voltage is forced to (1 + R1/R2) 63 mV rms by the AGC loop. For a 0 dBm (224 mV rms referenced to 50 ) output setpoint, this ratio is 3.5. After correcting for the input impedance of DETI, the choice of R1 = 226 and R2 = 100 yields a setpoint of roughly 0 dBm. This very accurate leveling function is shown in Figure 35, where the rms output is held to within 0.2 dB of the 0 dBm setpoint for >30 dB range of input levels. 1.5 1.0 10 5 05907-039 0.5 0 -40 -5 -30 -20 -10 0 10 20 POWER IN (dBm) -10 Figure 36. Monitoring the GAIN/DETO RSSI Voltage vs. Input Power -15 In some cases, it can be found that, if driven into AGC overload, the AD8368 requires unusually long times to recover; that is, the voltage at DETO remains at an abnormally high value, and the gain is at its lowest value. To avoid this situation, it is recommended that a clamp be placed on the DETO pin, as shown in Figure 37. -20 INPT ICOM VPSI MODE VPSO AD8368 VPSI CAGC 0.1F Table 5. DECL Capacitor Value C20 (pF) 2200 560 150 68 39 +VS VPSO VPSI OUTP ENBL OCOM GAIN VAGC RB 0.5V Q1 2N2907 RA A valuable feature of using a square law detector in AGC mode is that the RSSI voltage is a true reflection of signal power and can be converted to an absolute power measurement for any given source impedance. The RSSI in units of dBm referenced to 50 and based on the voltage available on the DETO pin is given by 05907-042 C4 (pF) 1000 270 68 33 15 VPSI OCOM Note that to achieve the accurate level of AGC output power, the DECL capacitor must be adjusted for the corresponding RF frequency. The DECL capacitor value varies depending on board parasitics. Table 5 shows the DECL capacitor value based on the evaluation board parasitics. IF Frequency (MHz) 70 140 240 380 480 VPSI ICOM Figure 35. Output Power vs. Input Power in AGC Mode at 140 MHz DECL 20 DECL 10 DETI 0 DECL -10 POWER IN (dBm) ICOM -20 ICOM -30 HPFL -30 -40 05907-038 -25 DETO POWER OUT (dBm) 0 Figure 37. External Clamp to Prevent AGC Overload The resistive divider network, RA and RB, should be designed such that the base of Q1 is driven to 0.5 V. RSSI = -11 + 20 log10(1 + R1/R2) + 38 x VDETO - 24.8 Rev. B | Page 15 of 20 AD8368 The choice of CDETO is a compromise of averaging time constant, response time, and carrier leakage. If CDETO is selected to be too small to speed up the response time, the AGC loop could start tracking and leveling any amplitude envelope and corrupt the constellation. Figure 38 illustrates a 16 QAM, 100 ksymbols per second constellation with a degraded error vector magnitude (EVM) of 5%. By increasing CDETO to 0.01 F, the EVM is improved to 1.1%. SR 10kHz CF 100MHz REF -4.9dBm 16 QAM MEAS SIGNAL CONST DIAG 1U 262.578mU/ In some applications, the printed circuit board (PCB) parasitic, in combination with the source impedance presented by the driving stage, can present some troublesome impedance at high frequency and can potentially unstablize the amplifier under certain extreme conditions, such as high gain and high temperature. To avoid such scenarios, it is recommended to include a simple parallel RL snubbing network directly at the input terminal of the AD8368. Figure 40 depicts an example of this network. The RL network formed by R3 and L1 is used to minimize the negative impact due to reflective source conditions at high RF frequencies and ensures the amplifier operates unconditionally stable and maintains the typical device performance. On the underside of the chip scale package, there is an exposed compressed paddle. This paddle is internally connected to the ground of the chip. Solder the paddle to the low impedance ground plane on the PCB to ensure specified electrical performance and to provide thermal relief. It is also recommended that the ground planes on all layers under the paddle be stitched together with vias to reduce thermal impedance. 05907-040 -1U -1.31289U STABILITY AND LAYOUT CONSIDERATIONS 1.31289U Figure 38. Degraded Error Vector Magnitude Performance for 16 QAM at 100 ksymbols per second (CDETO Too Small) Figure 39 illustrates the measured EVM performance for a 16 QAM modulation at 10 Msymbols per second using CDETO = 1 nF. 10 9 8 6 5 4 3 2 05907-041 EVM (%) 7 1 0 -40 -30 -20 -10 0 10 20 POWER IN (dBm) Figure 39. Error Vector Magnitude Performance for 16 QAM 10 Msymbols per second Rev. B | Page 16 of 20 AD8368 EVALUATION BOARD The standard evaluation board schematic and layout artwork is presented in Figure 41 through Figure 44. The evaluation board is fabricated on a multilayer FR-4 board, with 50 -controlled impedance transmission lines for the RF input and output traces. The board is powered by a single supply in the 4.5 V to 5.5 V range. The power supply is decoupled by 0.1 F and 1 nF capacitors at each power supply pin. Additional decoupling, in the form of a series resistor or inductor at the supply pins, can also be added. Table 6 details the various configuration options of the evaluation board. VPOS C20 1nF C2 5.6pF VPSI DECL ICOM DECL OUTP ENBL OCOM GAIN GAIN R35 OPEN COUT 10nF R32 OPEN C6 1nF OUTPUT C12 1nF VPOS3 C15 0.1F R31 OPEN C23 10nF JP4 DET_OUT_TP C14 0.1F R12 0 VPSO VPSI R2 10k C11 1nF VPOS2 C4 1nF C1 OPEN R30 OPEN DET_IN 05907-043 C10 1nF AD8368 R11 0 OCOM OFF VPSO DETI SW2 MODE VPSI R10 0 ON VPSI DECL C13 0.1F ICOM HPFL HI VPOS1 SW1 VPSI DETO LOW ENABLE ICOM L1 10nH R1 10k INPT GAIN INPUT R3 215 CIN 10nF ICOM VPOS1 VPOS2 VPOS3 Figure 40. Evaluation Board Table 6. Evaluation Board Configuration Options Component R1, R2, R3, L1 R10, R11, R12, C10, C11, C12, C13, C14, C15 CIN COUT R31, R32 R35 C23 C1, R30 C6 C20, C2, C4 Function Pull-Down Resistors for MODE and ENBL. RL network. Prevent potential instability impact due to PCB parasitics and/or certain extreme conditions (see the Stability and Layout Considerations section). Supply Decoupling. Jumpers, power supply decoupling resistors, and filter capacitors. RF Input. CIN provides dc block for RF input. RF Output. COUT provides dc block for RF output. Feedback Path for AGC Operation. For a default setpoint of 63 mV rms, set R31 = 0 and remove R32. For other AGC setpoints, rms voltage = (1 + n) x 63 mV rms, where n = R31/R32. Populate with 0 to feed detector output RSSI voltage to DET_OUT_TP. Sets the corner frequency of the output offset control loop high-pass filter. Used for driving the detector externally. Set R30 to 50 for matching. Set C1 to be a large ac coupling capacitor. DETO Capacitor. Needs to be made larger for lower data rates (see the AGC Operation section). DECL Capacitor. Needs to be adjusted based on RF frequency in AGC operation (see the AGC Operation section). Rev. B | Page 17 of 20 Default Conditions R1 = R2 = 10 k R3 = 215 L1 = 10 nH R10 = R11 = R12 = 0 C10 = C11 = C12 = 1 nF C13 = C14 = C15 = 0.1 F CIN = 10 nF COUT = 10 nF R31 = R32 = Open (VGA mode) R35 = Open C23 = 10 nF C1 = Open R30 = Open C6 = 1 nF C20 = C4 = 1 nF C2 = 5.6 pF AD8368 SW2 = JP3 Figure 41. Component Side Silkscreen 05907-046 Figure 43. Component Side Layout 05907-047 SW2 Default Conditions JP4 = not populated (VGA mode) SW1 = JP2 05907-044 SW1 Function Jumper for AGC Mode of Operation. Provides feedback from the detector output to the gain pin. Mode Switch. Low mode puts the part in gain-down mode. High mode puts the part in gain-up mode. AGC operation requires gain-down mode. Power-Down. The part is disabled when the enable pin is tied to ground. 05907-045 Component JP4 Figure 44. Circuit Side Layout Figure 42. Circuit Side Silkscreen Rev. B | Page 18 of 20 AD8368 OUTLINE DIMENSIONS 0.60 MAX 4.00 BSC SQ TOP VIEW 0.50 BSC 3.75 BSC SQ 0.50 0.40 0.30 1.00 0.85 0.80 12 MAX 0.80 MAX 0.65 TYP 0.30 0.23 0.18 SEATING PLANE PIN 1 INDICATOR 24 1 19 18 2.65 2.50 SQ 2.35 EXPOSED PAD (BOTTOMVIEW) 13 12 7 6 0.23 MIN 2.50 REF 0.05 MAX 0.02 NOM 0.20 REF COPLANARITY 0.08 FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-8 082908-A PIN 1 INDICATOR 0.60 MAX Figure 45. 24-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 4 mm x 4 mm Body, Very Thin Quad (CP-24-3) Dimensions shown in millimeters ORDERING GUIDE Model AD8368ACPZ-REEL7 1 AD8368ACPZ-WP1, 2 AD8368-EVALZ1 1 2 Temperature Range -40C to +85C -40C to +85C Package Description 24-Lead Lead Frame Chip Scale Package (LFCSP_VQ) 24-Lead Lead Frame Chip Scale Package (LFCSP_VQ) Evaluation Board Z = RoHS Compliant Part. WP = waffle pack. Rev. B | Page 19 of 20 Package Option CP-24-3 CP-24-3 Ordering Quantity 1,500 64 AD8368 NOTES (c)2006-2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05907-0-9/08(B) Rev. B | Page 20 of 20