Ordering information AC-DC Power Supplies Enclosed Type PBA10F PB 1 A 2 10 3 F Example recommended EMI/EMC filter NAC-06-472 R -O 4 High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current E :Low leakage current and EMI class A T :Vertical terminal block J :Connector type N :with Cover (UL508 is acquired) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally Cover is optional *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA10F-5 10 5V 2A PBA10F-12 10.8 12V 0.9A PBA10F-24 12 24V 0.5A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] *6 LOAD REGULATION[mV] *6 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA10F-5 PBA10F-12 PBA10F-24 AC85 - 264 1f or DC110 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *3) 0.30typ (Io=100%) 0.20typ (Io=100%) 50/60 (47 - 440) or DC 74typ 76typ 77typ 74typ 76typ 77typ 15typ (Io=100%) 30typ (Io=100%) 0.15/0.30max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 5 12 24 2 0.9 0.5 20max 48max 96max 40max 100max 150max 80max 120max 120max 140max 160max 160max 120max 150max 150max 160max 180max 180max 50max 120max 240max 60max 150max 290max 20max 48max 96max 200typ(ACIN 100V, Io=100%) *Start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage. 20typ (ACIN 100V, Io=100%) 4.50 - 5.50 10.0 - 13.2 19.2 - 27.0 5.00 - 5.15 12.00 - 12.48 24.00 - 24.96 Works over 105% of rated current and recovers automatically 5.75 - 7.00 15.0 - 18.0 30.0 - 37.0 LED (Green) None AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Not built-in to active filter *4) *7 31X78X68mm [1.22X3.07X2.68 inches] (without terminal block) (WXHXD) / 150g max (with cover : 180g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Derating is required. *4When two or more units are used,they may not comply with the harmonic attenuator. Please contact us for details. PBA/PBW-2 *5Please contact us about safety approvals for the model with option. *6Please contact us about dynamic load and input response. *7Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA10F Block diagram FUSE AC250V 2.5A AC IN 85 - 264V NOISE FILTER INRUSH CURRENT LIMIT RECTIFIER AND FILTER FG TRANSFORMER CONTROL RECTIFIER AND FILTER INVERTER DC OUT CURRENT SENSING Photocoupler CONTROL Photocoupler OVER VOLTAGE PROTECTION External view External size of option T,J,N,N1 and V is different from standard model and refer to 7 Option of instruction manual for details. 18 Voltage adjust [0.71] 12.21.5 [0.48] 2.5 LED [0.1] 16.52 Cover name plate 68 [0.65] [2.68] M3 2-M3 Mounting hole AC(N) 15.11.5 [0.59] 78 49.50.5 Terminal cover 4 [1.95] 22.61.5 [0.89] [1.36] 11.5 9.5 [0.45] [0.37] 34.5 [0.3] FG AC(L) [3.07] Cover (option) -V 7.5 70.5 [2.78] +V [0.16] Point A:C102 Name plate 18 Tolerance : 1 [0.04] Weight : 150g max (with cover : 180g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Electric galvanizing steel board Dimensions in mm, [ ]= inches Mounting torque : 0.6N * m(6.3kgf * cm)max Screw tightening torque : M3 0.8N * m(8.5kgf * cm)max Please connect safety ground to the unit in 2-M3 holes. [0.71] 31 PBA10F [1.22] 34.5 [1.36] 2-M3 Mounting hole 36 0.5 [1.42] 11 [0.43] PBA/PBW-3 Ordering information AC-DC Power Supplies Enclosed Type PBA15F PB 1 A 15 2 3 F 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. Cover is optional -O 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current E :Low leakage current and EMI class A T :Vertical terminal block J :Connector type N :with Cover (UL508 is acquired [5V, 12V, 24V]) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA15F-3R3 9.9 3.3V 3A PBA15F-5 15 5V 3A PBA15F-9 15.3 9V 1.7A PBA15F-12 15.6 12V 1.3A PBA15F-15 15 15V 1A PBA15F-24 16.8 24V 0.7A PBA15F-48 16.8 48V 0.35A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS PBA15F-3R3 PBA15F-5 PBA15F-9 PBA15F-12 PBA15F-15 PBA15F-24 PBA15F-48 AC85 - 264 1f or DC110 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *3) ACIN 100V 0.30typ (Io=100%) 0.4typ (Io=100%) ACIN 200V 0.15typ (Io=100%) 0.2typ (Io=100%) 50/60 (47 - 440) or DC ACIN 100V ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] *6 LOAD REGULATION[mV] *6 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] 68typ 74typ 75typ 75typ 77typ 75typ 75typ 68typ 75typ 77typ 78typ 80typ 78typ 78typ 15typ (Io=100%) (At cold start) 30typ (Io=100%) (At cold start) 0.15/0.30max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 9 12 15 24 48 3 3 1.7 1.3 1 0.7 0.35 20max 20max 36max 48max 60max 96max 192max 40max 40max 100max 100max 120max 150max 240max 80max 80max 120max 120max 120max 120max 150max 140max 140max 160max 160max 160max 160max 200max 120max 120max 150max 150max 150max 150max 250max 160max 160max 180max 180max 180max 180max 300max 50max 50max 90max 120max 150max 240max 480max 60max 60max 120max 150max 180max 290max 600max 20max 20max 36max 48max 60max 96max 192max 200typ(ACIN 100V, Io=100%) *Start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage. 20typ (ACIN 100V, Io=100%) 2.85 - 3.60 4.50 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 39.0 - 53.0 3.30 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 48.00 - 49.92 Works over 105% of rated current and recovers automatically 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 58.0 - 65.0 LED (Green) None AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Not built-in to active filter *4) *7 31X78X85mm [1.22X3.07X3.35 inches] (without terminal block) (WXHXD) / 200g max (with cover : 235g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Derating is required. *4When two or more units are used,they may not comply with the harmonic attenuator. Please contact us for details. PBA/PBW-4 *5Please contact us about safety approvals for the model with option. *6Please contact us about dynamic load and input response. *7Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA15F Block diagram FUSE AC250V 2.5A AC IN 85 - 264V INRUSH CURRENT LIMIT NOISE FILTER RECTIFIER AND FILTER FG TRANSFORMER CONTROL RECTIFIER AND FILTER INVERTER DC OUT CURRENT SENSING Photocoupler CONTROL Photocoupler OVER VOLTAGE PROTECTION External view External size of option T,J,N,N1 and V is different from standard model and refer to 7 Option of instruction manual for details. 18 Voltage adjust [0.71] 12.21.5 [0.48] 2.5 [0.1] LED 16.52 85 [0.65] Cover name plate [3.35] M3 78 [1.36] 34.5 7.5 [1.22] Point A:C102 [1.44] 2-M3 Mounting hole Name plate 2-M3 Mounting hole [1.36] [0.89] 36.5 310.5 Terminal cover 22.61.5 34.5 [0.59] 18 [0.71] Tolerance : 1 [0.04] Weight : 200g max (with cover : 235g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Electric galvanizing steel board Dimensions in mm, [ ]= inches Mounting torque : 0.6N * m(6.3kgf * cm)max Screw tightening torque : M3 0.8N * m(8.5kgf * cm)max Please connect safety ground to the unit in 2-M3 holes. 31 PBA15F PBW15F [1.22] 15.11.5 [0.3] AC(N) [0.45] [0.37] FG AC(L) [3.07] Cover (option) -V 11.5 9.5 70.5 [2.78] +V 60 0.5 [2.36] 5 [0.2] PBA/PBW-5 Ordering information AC-DC Power Supplies Enclosed Type PBA30F PB 1 A 30 2 3 F 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. Cover is optional -O 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current E :Low leakage current and EMI class A T :Vertical terminal block J :Connector type N :with Cover (UL508 is acquired [5V, 12V, 24V]) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA30F-3R3 19.8 3.3V 6A PBA30F-5 30 5V 6A PBA30F-9 30.6 9V 3.4A PBA30F-12 30 12V 2.5A PBA30F-15 30 15V 2A PBA30F-24 31.2 24V 1.3A PBA30F-48 31.2 48V 0.65A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS PBA30F-3R3 PBA30F-5 PBA30F-9 PBA30F-12 PBA30F-15 PBA30F-24 PBA30F-48 AC85 - 264 1f or DC110 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *3) ACIN 100V 0.50typ (Io=100%) 0.70typ (Io=100%) ACIN 200V 0.30typ (Io=100%) 0.40typ (Io=100%) 50/60 (47 - 440) or DC ACIN 100V ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] *6 LOAD REGULATION[mV] *6 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] 68typ 74typ 75typ 76typ 78typ 78typ 79typ 69typ 77typ 77typ 78typ 81typ 81typ 81typ 15typ (Io=100%) (At cold start) 30typ (Io=100%) (At cold start) 0.30/0.65max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 9 12 15 24 48 6 6 3.4 2.5 2 1.3 0.65 20max 20max 36max 48max 60max 96max 192max 40max 40max 100max 100max 120max 150max 240max 80max 80max 120max 120max 120max 120max 150max 140max 140max 160max 160max 160max 160max 200max 120max 120max 150max 150max 150max 150max 250max 160max 160max 180max 180max 180max 180max 300max 50max 50max 90max 120max 150max 240max 480max 60max 60max 120max 150max 180max 290max 600max 20max 20max 36max 48max 60max 96max 192max 200typ(ACIN 100V, Io=100%) *Start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage. 20typ (ACIN 100V, Io=100%) 2.85 - 3.60 4.50 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 39.0 - 53.0 3.30 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 48.00 - 49.92 Works over 105% of rated current and recovers automatically 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 58.0 - 65.0 LED (Green) None AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Not built-in to active filter *4) *7 31X78X103mm [1.22X3.07X4.06 inches] (without terminal block) (W XHXD) / 270g max (with cover : 310g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Derating is required. *4When two or more units are used,they may not comply with the harmonic attenuator. Please contact us for details. PBA/PBW-6 *5Please contact us about safety approvals for the model with option. *6Please contact us about dynamic load and input response. *7Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA30F Block diagram FUSE AC250V 3.15A AC IN 85 - 264V INRUSH CURRENT LIMIT NOISE FILTER RECTIFIER AND FILTER FG TRANSFORMER CONTROL INVERTER RECTIFIER AND FILTER DC OUT CURRENT SENSING Photocoupler CONTROL Photocoupler OVER VOLTAGE PROTECTION External view External size of option T,J,N,N1 and V is different from standard model and refer to 7 Option of instruction manual for details. 18 Voltage adjust [0.71] 12.2 1.5 [0.48] 2.5 [0.1] LED 16.52 Cover name plate 103 [0.65] [4.06] M3 22.6 1.5 [0.89] 78 [3.07] 40.5 [1.81] [1.59] Point A:C102 2-M3 Mounting hole Name plate 2-M3 Mounting hole 18 PBA30F PBW30F Tolerance : 1 [0.04] Weight : 270g max (with cover : 310g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Electric galvanizing steel board Dimensions in mm, [ ]= inches Mounting torque : 0.6N * m(6.3kgf * cm)max Screw tightening torque : M3 0.8N * m(8.5kgf * cm)max Please connect safety ground to the unit in 2-M3 holes. [1.44] 36.5 460.5 Terminal cover 75 0.5 [2.95] [1.36] [0.59] [0.71] 31 [1.22] 34.5 15.11.5 7.5 AC(N) [0.3] FG AC(L) 11.5 9.5 Cover (option) -V [0.45] [0.37] 70.5 [2.78] +V 8.5 [0.33] PBA/PBW-7 Ordering information AC-DC Power Supplies Enclosed Type PBA50F PB 1 A 2 50 3 F 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current (0.15mA max / ACIN 240V) E :Low leakage current and EMI class A (0.5mA max / ACIN 240V) T :Vertical terminal block J :Connector type R :with Remote ON/OFF N :with Cover (Only 24V UL508 is acquired) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally Cover is optional *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA50F-3R3 33 3.3V 10A PBA50F-5 50 5V 10A PBA50F-9 50.4 9V 5.6A PBA50F-12 51.6 12V 4.3A PBA50F-15 52.5 15V 3.5A PBA50F-24 52.8 24V 2.2A PBA50F-36 50.4 36V 1.4A PBA50F-48 52.8 48V 1.1A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR(Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE ON/OFF INPUT-OUTPUT -RC *3 INPUT-FG OUTPUT-RC-FG *3 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA50F-3R3 PBA50F-5 PBA50F-9 PBA50F-12 PBA50F-15 PBA50F-24 PBA50F-36 PBA50F-48 AC85 - 264 1f or DC120 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *4) 0.5typ 0.7typ 0.3typ 0.4typ 50/60 (47 - 63) 75typ 80typ 79typ 80typ 81typ 82typ 83typ 83typ 76typ 82typ 81typ 82typ 83typ 84typ 85typ 85typ 0.98typ 0.99typ 0.87typ 0.93typ 15typ (Io=100%) (At cold start) 30typ (Io=100%) (At cold start) 0.4/0.75max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 9 12 15 24 36 48 10 10 5.6 4.3 3.5 2.2 1.4 1.1 20max 20max 36max 48max 60max 96max 144max 192max 40max 40max 100max 100max 120max 150max 240max 240max 80max 80max 120max 120max 120max 120max 150max 150max 140max 140max 160max 160max 160max 160max 200max 200max 120max 120max 150max 150max 150max 150max 250max 250max 160max 160max 180max 180max 180max 180max 300max 300max 50max 50max 90max 120max 150max 240max 360max 480max 60max 60max 120max 150max 180max 290max 450max 600max 20max 20max 36max 48max 60max 96max 144max 192max 350typ(ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 - 3.63 4.00 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 28.8 - 39.6 39.0 - 53.0 3.30 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 35.00 - 37.44 48.00 - 49.92 Works over 105% of rated current and recovers automatically 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 43.0 - 50.0 58.0 - 65.0 LED (Green) Optional (Required external power source) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *6 31X82X120mm [1.22X3.23X4.72 inches] (without terminal block) (WXHXD) / 280g max (with cover : 325g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Applicable when Remote ON/OFF(optional) is added. RC is insulated with input, output and FG. *4Derating is required. PBA/PBW-8 *5Please contact us about safety approvals for the model with option. *6Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA50F Block diagram FUSE 250V2A NOISE FILTER AC IN 85 - 264V RECTIFIER INRUSH CURRENT LIMIT FG CURRENT SENSING BOOSTER INDUCTOR CURRENT SENSING OPTION RC EXTERNAL SOURCE RECTIFIER AND FILTER CONTROL CONTROL OVER VOLTAGE PROTECTION INVERTER INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL E DC OUT External view External size of option T,J,R,N,N1 and V is different from standard model and refer to 7 Option of instruction manual for details. CN3 Connector for Remote ON/OFF (option) (20) (16.5) 120 [0.65] [0.02] LED [0.43] [4.72] 0.5 [0.79] Voltage adjust (11) 12 M3 Cover (option) [3.03] (21.5) 4 [0.16] [0.85] 88 0.5 [3.46] Connector type CN3 Option (Mfr : J.S.T.) Pin No. 1 2 Contents RC(+) RC( - ) 31 PBA50F 18 Tolerance : 1 [0.04] Weight : 280g max (with cover : 325g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Aluminum Dimensions in mm, [ ]= inches Mounting torque : 0.49N * m(5kgf * cm)max Screw tightening torque : M3 0.8N * m(8.5kgf * cm)max Please connect safety ground to the unit in 2-M3 holes. 3.5 Name plate 2-M3 Mounting hole [0.14] 77 0.5 Terminal cover Point A [1.22] (14) [0.55] 35 (12) 9.5 [0.47] [0.37] AC(N) A 2-M3 Mounting hole [1.38] FG AC(L) 11 [0.43] [0.71] 7.5 82 [3.23] -V [0.3] [2.8] (71) +V Barrier strip type Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 ( ) PBA/PBW-9 Ordering information AC-DC Power Supplies Enclosed Type PBA75F PB 1 A 2 75 3 F 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current (0.15mA max / ACIN 240V) E :Low leakage current and EMI class A (0.5mA max / ACIN 240V) T :Vertical terminal block J :Connector type R :with Remote ON/OFF N :with Cover (Only 24V UL508 is acquired) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally Cover is optional *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA75F-3R3 49.5 3.3V 15A PBA75F-5 75 5V 15A PBA75F-9 75.6 9V 8.4A PBA75F-12 75.6 12V 6.3A PBA75F-15 75 15V 5A PBA75F-24 76.8 24V 3.2A PBA75F-36 75.6 36V 2.1A PBA75F-48 76.8 48V 1.6A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR(Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE ON/OFF INPUT-OUTPUT -RC *3 INPUT-FG OUTPUT-RC-FG *3 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA75F-3R3 PBA75F-5 PBA75F-9 PBA75F-12 PBA75F-15 PBA75F-24 PBA75F-36 PBA75F-48 AC85 - 264 1f or DC120 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *4) 0.7typ 1.0typ 0.4typ 0.5typ 50/60 (47 - 63) 77typ 81typ 80typ 81typ 82typ 83typ 84typ 84typ 78typ 83typ 82typ 83typ 84typ 85typ 86typ 86typ 0.98typ 0.99typ 0.87typ 0.93typ 15typ (Io=100%) (At cold start) 30typ (Io=100%) (At cold start) 0.4/0.75max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 9 12 15 24 36 48 15 15 8.4 6.3 5 3.2 2.1 1.6 20max 20max 36max 48max 60max 96max 144max 192max 40max 40max 100max 100max 120max 150max 240max 240max 80max 80max 120max 120max 120max 120max 150max 150max 140max 140max 160max 160max 160max 160max 200max 200max 120max 120max 150max 150max 150max 150max 250max 250max 160max 160max 180max 180max 180max 180max 300max 300max 50max 50max 90max 120max 150max 240max 360max 480max 60max 60max 120max 150max 180max 290max 450max 600max 20max 20max 36max 48max 60max 96max 144max 192max 350typ(ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 - 3.63 4.00 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 28.8 - 39.6 39.0 - 53.0 3.30 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 48.00 - 49.92 Works over 105% of rated current and recovers automatically 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 43.0 - 50.0 58.0 - 65.0 LED (Green) Optional (Required external power source) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *6 32X82X135mm [1.26X3.23X5.31 inches] (without terminal block) (WXHXD) / 350g max (with cover : 400g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Applicable when Remote ON/OFF(optional) is added. RC is insulated with input, output and FG. *4Derating is required. PBA/PBW-10 *5Please contact us about safety approvals for the model with option. *6Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA75F Block diagram FUSE 250V3.15A AC IN 85 - 264V NOISE FILTER RECTIFIER INRUSH CURRENT LIMIT FG CURRENT SENSING BOOSTER INDUCTOR OPTION RC EXTERNAL SOURCE CURRENT SENSING RECTIFIER AND FILTER CONTROL CONTROL OVER VOLTAGE PROTECTION INVERTER INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL E DC OUT External view External size of option T,J,R,N,N1 and V is different from standard model and refer to 7 Option of instruction manual for details. CN3 Connector for Remote ON/OFF (option) [0.79] (11) (16.5) LED 135 [0.65] [0.43] [5.31] 0.5 Voltage adjust [0.02] (20) 12 M3 Cover (option) [3.23] 82 -V [0.3] FG 7.5 Terminal cover (21.5) 35 [0.16] Name plate 105.50.5 [4.15] 3.5 18 PBA75F Tolerance : 1 [0.04] Weight : 350g max (with cover : 400g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Aluminum Dimensions in mm, [ ]= inches Mounting torque : 0.49N * m(5kgf * cm)max Screw tightening torque : M3 0.8N * m(8.5kgf * cm)max Please connect safety ground to the unit in 2-M3 holes. 2-M3 Mounting hole [0.14] [0.85] Point A 4 94 0.5 [3.7] 32 (14) [0.55] A [1.26] AC(N) 2-M3 Mounting hole [1.38] (12) 9.5 [0.47] [0.37] AC(L) 9 [0.35] [0.71] [2.8] (71) +V Connector type CN3 Option (Mfr : J.S.T.) Pin No. 1 2 Contents RC(+) RC( - ) Barrier strip type Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 ( ) PBA/PBW-11 Ordering information AC-DC Power Supplies Enclosed Type PBA100F PB 1 A 2 100 3 F 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current (0.15mA max / ACIN 240V) E :Low leakage current and EMI class A (0.5mA max / ACIN 240V) T :Vertical terminal block J :Connector type (Only -12,-15,-24,-36,-48) R :with Remote ON/OFF N :with Cover (Only 24V UL508 is acquired) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally Cover is optional *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA100F-3R3 PBA100F-5 66 100 3.3V 20A 5V 20A PBA100F-9 94.5 9V 10.5A PBA100F-12 102 12V 8.5A PBA100F-15 105 15V 7A PBA100F-24 108 24V 4.5A PBA100F-36 100.8 36V 2.8A PBA100F-48 100.8 48V 2.1A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR(Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC *3 INPUT-FG OUTPUT-RC-FG *3 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA100F-3R3 PBA100F-5 PBA100F-9 PBA100F-12 PBA100F-15 PBA100F-24 PBA100F-36 PBA100F-48 AC85 - 264 1f or DC120 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *4) 0.9typ 1.3typ 0.5typ 0.7typ 50/60 (47 - 63) 77typ 82typ 80typ 81typ 83typ 84typ 84typ 84typ 79typ 84typ 82typ 83typ 86typ 86typ 86typ 86typ 0.98typ 0.99typ 0.87typ 0.93typ 20typ (Io=100%) (At cold start) 40typ (Io=100%) (At cold start) 0.4/0.75max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 9 12 15 24 36 48 20 20 10.5 8.5 7 4.5 2.8 2.1 20max 20max 36max 48max 60max 96max 144max 192max 40max 40max 100max 100max 120max 150max 240max 240max 80max 80max 120max 120max 120max 120max 150max 150max 140max 140max 160max 160max 160max 160max 200max 200max 120max 120max 150max 150max 150max 150max 250max 250max 160max 160max 180max 180max 180max 180max 300max 300max 50max 50max 90max 120max 150max 240max 360max 480max 60max 60max 120max 150max 180max 290max 450max 600max 20max 20max 36max 48max 60max 96max 144max 192max 350typ(ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 - 3.63 4.00 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 28.8 - 39.6 39.0 - 53.0 3.20 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 48.00 - 49.92 Works over 105% of rated current and recovers automatically 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 43.0 - 50.0 58.0 - 65.0 LED (Green) Optional (Only -3R3, -5 Option -K) Optional (Required external power source) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *6 32X93X147mm [1.26X3.66X5.79 inches] (without terminal block) (WXHXD) / 440g max (with cover : 500g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Applicable when Remote ON/OFF(optional) is added. RC is insulated with input, output and FG. *4Derating is required. PBA/PBW-12 *5Please contact us about safety approvals for the model with option. *6Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA100F Block diagram FUSE 250V3.15A AC IN 85 - 264V NOISE FILTER RECTIFIER INRUSH CURRENT LIMIT FG CURRENT SENSING BOOSTER INDUCTOR CURRENT SENSING OPTION RC EXTERNAL SOURCE RECTIFIER AND FILTER CONTROL CONTROL OVER VOLTAGE PROTECTION INVERTER INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL E DC OUT External view External size of option T,J,R,N,N1,V and K is different from standard model and refer to 7 Option of instruction manual for details. CN3 Connector for Remote ON/OFF (option) CN4 Connector for Remote sensing (option : only -3R3, -5) (20) (13.5) Terminal cover [5.79] 0.5 147 [0.53] [0.02] LED 93 (11) Voltage adjust [0.43] [3.66] [0.79] 12 M4 +V +V Cover (option) -V (14) 1240.5 [0.55] [0.16] 3-M3 Mounting hole [0.93] [0.37] [0.51] 9.5 130.5 3.5 Name plate PBA100F [0.71] 18 Tolerance : 1 [0.04] Weight : 440g max (with cover : 500g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Aluminum Dimensions in mm, [ ]= inches Mounting torque : 0.49N * m(5kgf * cm)max Mounting torque : M4:1.6N * m(16.9kgf * cm)max Please connect safety ground to FG terminal on the unit. 112.5 0.5 [4.43] [1.32] 4 [4.88] (23.5) Point A 15 [0.59] [0.14] AC(N) [1.26] (10) 10 [0.39] [0.39] AC(L) A 2-M3 Mounting hole 33.5 ) 32 8.6 FG( [0.34] (81) [3.19] -V Connector type CN3 Option (Mfr : J.S.T.) Pin No. 1 2 Contents RC(+) RC( - ) Barrier strip type Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 ( ) PBA/PBW-13 Ordering information AC-DC Power Supplies Enclosed Type PBA150F PB 1 A 2 150 3 F 4 Example recommended EMI/EMC filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series * A higher current rating EMI/EMC filter may be recommended in view of the other devices that could be connected in parallel with the power supply. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current (0.15mA max / ACIN 240V) E :Low leakage current and EMI class A (0.5mA max / ACIN 240V) T :Vertical terminal block J :Connector type (Only -12,-15,-24,-36,-48) R :with Remote ON/OFF N :with Cover (Only 24V UL508 is acquired) N1 :with DIN rail and Cover V :Output voltage setting potentiometer externally Cover is optional *Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA150F-3R3 PBA150F-5 99 150 3.3V 30A 5V 30A PBA150F-9 150.3 9V 16.7A PBA150F-12 156 12V 13A PBA150F-15 150 15V 10A PBA150F-24 156 24V 6.5A PBA150F-36 154.8 36V 4.3A PBA150F-48 158.4 48V 3.3A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR(Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC *3 INPUT-FG OUTPUT-RC-FG *3 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA150F-3R3 PBA150F-5 PBA150F-9 PBA150F-12 PBA150F-15 PBA150F-24 PBA150F-36 PBA150F-48 AC85 - 264 1f or DC120 - 370 (AC50 or DC70 Please refer to the instruction manual 2.1 Input voltage *4) 1.3typ 2.0typ 0.7typ 1.0typ 50/60 (47 - 63) 80typ 83typ 82typ 83typ 84typ 85typ 85typ 85typ 82typ 86typ 85typ 86typ 87typ 88typ 88typ 88typ 0.98typ 0.99typ 0.87typ 0.93typ 20typ (Io=100%) (At cold start) 40typ (Io=100%) (At cold start) 0.4/0.75max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 9 12 15 24 36 48 30 30 16.7 13 10 6.5 4.3 3.3 20max 20max 36max 48max 60max 96max 144max 192max 40max 40max 100max 100max 120max 150max 240max 240max 80max 80max 120max 120max 120max 120max 150max 150max 140max 140max 160max 160max 160max 160max 200max 200max 120max 120max 150max 150max 150max 150max 250max 250max 160max 160max 180max 180max 180max 180max 300max 300max 50max 50max 90max 120max 150max 240max 360max 480max 60max 60max 120max 150max 180max 290max 450max 600max 20max 20max 36max 48max 60max 96max 144max 192max 350typ(ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 - 3.63 4.00 - 5.50 7.50 - 10.0 10.0 - 13.2 13.2 - 18.0 19.2 - 27.0 28.8 - 39.6 39.0 - 53.0 3.30 - 3.40 5.00 - 5.15 9.00 - 9.36 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 48.00 - 49.92 Works over 105% of rated current and recovers automatically 4.00 - 5.25 5.75 - 7.00 11.5 - 14.0 15.0 - 18.0 20.0 - 25.0 30.0 - 37.0 43.0 - 50.0 58.0 - 65.0 LED (Green) Optional (Only -3R3, -5 Option -K) Optional (Required external power source) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -10 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *6 34X93X168mm [1.34X3.66X6.61 inches] (without terminal block) (WXHXD) / 560g max (with cover : 630g max) Convection *1Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3Applicable when Remote ON/OFF(optional) is added. RC is insulated with input, output and FG. *4Derating is required. PBA/PBW-14 *5Please contact us about safety approvals for the model with option. *6Please contact us about class C. *Parallel operation with other model is not possible. *Derating is required when operated with cover. *A sound may occur from power supply at peak loading. PBA150F Block diagram FUSE 250V4A NOISE FILTER AC IN 85 - 264V RECTIFIER INRUSH CURRENT LIMIT FG CURRENT SENSING BOOSTER INDUCTOR CURRENT SENSING OPTION RC EXTERNAL SOURCE RECTIFIER AND FILTER CONTROL CONTROL OVER VOLTAGE PROTECTION INVERTER INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL E DC OUT External view External size of option T,J,R,N,N1,V and K is different from standard model and refer to 7 Option of instruction manual for details. CN3 Connector for Remote ON/OFF (option) [0.45] LED (13.5) 168 [0.53] [6.61] 0.5 Voltage adjust (11.5) [0.02] CN4 Connector for Remote sensing (option : only -3R3, -5) (20.5) [0.81] 12 +V M4 +V Terminal cover 93 TB1 [0.57] 78 0.5 58.5 [3.07] [2.3] 2-M3 Mounting hole (24) 3.5 Name plate 19 [0.75] PBA150F Tolerance : 1 [0.04] Weight : 560g max (with cover : 630g max) PCB Material/thickness : CEM3 / 1.6mm [0.06] Chassis material : Aluminum Dimensions in mm, [ ]= inches Mounting torque : 0.49N * m(5kgf * cm)max Mounting torque : M4:1.6N * m(16.9kgf * cm)max Keep drawing current per pin below 20A for TB1. Please connect safety ground to FG terminal on the unit. 139.50.5 [5.49] Connector type CN3 Option (Mfr : J.S.T.) Pin No. 1 2 Contents RC(+) RC( - ) 34 [0.94] [0.14] (14.5) Point A [1.34] AC(N) A 2-M3 Mounting hole 37.5 (10) 10 AC(L) [1.48] 8.6 ) [0.34] -V [0.39] [0.39] (81) [3.19] FG( [3.66] Cover (option) -V 9 [0.35] Barrier strip type Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 ( ) PBA/PBW-15