SHV-06JN High Voltage Rectifier Diode Features and Benefits Description High Peak Reverse Voltage, VRM : 3.0 kV Low Forward Voltage, VF : 6.0 V (max.) at IF = 10 mA Peak Forward Surge Current, IFSM : 3 A Average Forward Current, IF(AV) : 30 mA Flammability rating UL94V-0 (Equivalent) Pins Pb (lead) free The SHV-06JN is a 3000 V silicon rectifier diode, which can sustain a high voltage with low loss. Application Automobile ignition coil start-up voltage surge arrester Package: Axial Not to scale Product Structure Epoxy resin body Silver plated copper wire pins Application overmolding SHV06JN-DS SANKEN ELECTRIC CO., LTD. http://www.sanken-ele.co.jp/en/ December 5, 2006 High Voltage Rectifier Diode SHV-06JN Selection Guide Part Number SHV-06JNV1 Packing 5000 pieces per reel Absolute Maximum Ratings Characteristic Peak Reverse Voltage Symbol Conditions VRM Peak Reverse Surge Current IRSM Half value width: 100 s Triangular wave, peak value, one shot Average Forward Current IF(AV) 50 Hz, half sine wave, average value Peak Forward Surge Current IFSM 50 Hz, half sine wave, one shot Rating Unit 3.0 kV 30 mA 30 mA 3 A Junction Temperature Tj -40 to 150 C Storage Temperature Tstg -40 to 150 C Electrical Characteristics valid at TA = 25C, unless otherwise specified Characteristic Forward Voltage Symbol Test Conditions Value Unit 6.0 (max) V VR = VRM 10 (max) A IR = 100 A 3.2 to 6.0 kV VF IF = 10 mA Reverse Current IR Reverse Breakdown Voltage VZ SHV06JN-DS SANKEN ELECTRIC CO., LTD. 2 December 5, 2006 High Voltage Rectifier Diode SHV-06JN Electrical Operation Tests Open Operation Test The ratings in the Electrical Characteristics must be satisfied after tests at the following condition Test Condition Reverse Current Waveform Through Diode Ambient Temperature, TA : 130C Capacitance: C: 25 pF 1) f = 66 Hz for 3 minutes 2) f = 33.3 Hz for 20 hours VTEST = 16 V C = 25 pF Pulse Width : 60 s Peak Value: 30 mA Power per pulse: 9.6 mJ IR IR(peak) = 30 mA 0A f 60 s IF Igniter Spark Discharge Test The ratings in the Electrical Characteristics must be satisfied after tests at the following condition Test Condition Ambient Temperature, TA : 130C Secondary Discharge Voltage: 25 5 kV L1: less than 100 mm L2: less than 500 mm f = 66.6 Hz T = 1000 hours Reverse Current Waveform Through Diode VTEST = 16 V IF L1 f Igniter L2 Capacitive Current 50 mA Inductive Current 0A 1 ms Note: Additional conditions during electrical operation tests in this page 1. Sample diode should be overmolded with more than 10 mm x 10 mm x 30 mm of epoxy resin, but thermal resistance, Rth(j-a) , at 1 W dissipation less than 65/W. 2. If product high-voltage code is not specified, no line noise resistance is specified. SHV06JN-DS SANKEN ELECTRIC CO., LTD. 3 December 5, 2006 High Voltage Rectifier Diode SHV-06JN Package Outline 6.50.2 27 MIN Cathode Index Band 1 27 MIN O2.500.2 0.5 +0.01 -0.02 2 Dimensions in mm Pin dimension does not include trim burr Package Marking Cathode index band YMD Type mark Marking repeats on far side Lot Number Y is the last digit of the year (0 to 9) M is the month (1 to 9, O, N, D) D is the period of days A - 1st to 10th B - 11th to 20th C - 21st to 31st Material Composition and Internal Structure 1 2 1. Body: Plastic, epoxy resin 2. Pins: Cu wire Ag plated Caution for Use The body is intentionally small, with the expectation that the product will be overmolded in the application where used. For this reason, the use of the diode is not recommended unless it is overmolded. Overmolding is required to insure insulation against voltage at the surface, heat dissipation, and to protect against penetration of moisture. An epoxy resin should be used for the overmolding. It must have superior adhesion to the surface of the product body, thermal conduction, protection against penetration of moisture, and must have low distortion when expanding and contracting while the product is being used in the application. SHV06JN-DS Pin treatment Pb-free. Device composition compliant with the RoHS directive. SANKEN ELECTRIC CO., LTD. 4 December 5, 2006 High Voltage Rectifier Diode SHV-06JN * The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the latest revision of the document before use. * Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the products herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or any other rights of Sanken or any third party which may result from its use. * Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device failure or malfunction. * Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equipment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.). When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales representative to discuss, prior to the use of the products herein. The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required (aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited. * In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general, derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses, instantaneous values, maximum values and minimum values must be taken into consideration. In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of derating of junction temperature affects the reliability significantly. * When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance and proceed therewith at your own responsibility. * Anti radioactive ray design is not considered for the products listed herein. * Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribution network. * The contents in this document must not be transcribed or copied without Sanken's written consent. SHV06JN-DS SANKEN ELECTRIC CO., LTD. 5 December 5, 2006