SHV-06JNV1 - Sanken Electric

SANKEN ELECTRIC CO., LTD.

http://www.sanken-ele.co.jp/en/

Description

The SHV-06JN is a 3000 V silicon rectifier diode, which can

sustain a high voltage with low loss.

High Voltage Rectifier Diode

Not to scale

SHV-06JN

SHV06JN-DS December 5, 2006

Package: Axial

Features and Benefits

▪ High Peak Reverse Voltage, VRM : 3.0 kV

▪ Low Forward Voltage, VF : 6.0 V (max.) at IF = 10 mA

▪ Peak Forward Surge Current, IFSM : 3 A

▪ Average Forward Current, IF(AV) : 30 mA

▪ Flammability rating UL94V-0 (Equivalent)

▪ Pins Pb (lead) free

Application

▪ Automobile ignition coil start-up voltage surge arrester

Product Structure

Epoxy resin body

Application overmolding

Silver plated copper wire pins

SANKEN ELECTRIC CO., LTD.

SHV06JN-DS

High Voltage Rectifier Diode

SHV-06JN

December 5, 2006

Absolute Maximum Ratings

Characteristic Symbol Conditions Rating Unit

Peak Reverse Voltage VRM 3.0 kV

Peak Reverse Surge Current IRSM

Half value width: 100 μs

Triangular wave, peak value, one shot 30 mA

Average Forward Current IF(AV) 50 Hz, half sine wave, average value 30 mA

Peak Forward Surge Current IFSM 50 Hz, half sine wave, one shot 3 A

Junction Temperature Tj–40 to 150 °C

Storage Temperature Tstg –40 to 150 °C

Electrical Characteristics valid at TA = 25°C, unless otherwise specified

Characteristic Symbol Test Conditions Value Unit

Forward Voltage VF IF = 10 mA 6.0 (max) V

Reverse Current IR VR = VRM 10 (max) μA

Reverse Breakdown Voltage VZIR = 100 μA 3.2 to 6.0 kV

Selection Guide

Part Number Packing

SHV-06JNV1 5000 pieces per reel

SANKEN ELECTRIC CO., LTD.

SHV06JN-DS

High Voltage Rectifier Diode

SHV-06JN

December 5, 2006

Ambient Temperature, TA : 130°C

Capacitance: C: 25 pF

1) f = 66 Hz for 3 minutes

2) f = 33.3 Hz for 20 hours

Ambient Temperature, TA : 130°C

Secondary Discharge Voltage: 25 ±5 kV

L1: less than 100 mm

L2: less than 500 mm

f = 66.6 Hz

T = 1000 hours

Pulse Width : 60 μs

Peak Value: 30 mA

Power per pulse: 9.6 mJ

Test Condition

Reverse Current Waveform Through Diode

C = 25 pF

VTEST = 16 V

fIgniter

Igniter

VTEST = 16 V

IR(peak) = 30 mA

60 μs

0 A

Inductive

Current

Capacitive

Current

1 ms

0 A

50 mA

Electrical Operation Tests

Spark Discharge Test

The ratings in the Electrical Characteristics must be satisfied after tests at the following condition

Open Operation Test

The ratings in the Electrical Characteristics must be satisfied after tests at the following condition

Note: Additional conditions during electrical operation tests in this page

1. Sample diode should be overmolded with more than 10 mm × 10 mm × 30 mm of epoxy

resin, but thermal resistance, Rth(j-a) , at 1 W dissipation less than 65°/W.

2. If product high-voltage code is not specified, no line noise resistance is specified.

SANKEN ELECTRIC CO., LTD.

SHV06JN-DS

High Voltage Rectifier Diode

SHV-06JN

December 5, 2006

YMD

Lot Number

Y is the last digit of the year (0 to 9)

M is the month (1 to 9, O, N, D)

D is the period of days

A – 1st to 10th

B – 11th to 20th

C – 21st to 31st

Marking repeats

on far side

Package Outline

Package Marking

Material Composition and Internal Structure

6.5±0.2

27 MIN 27 MIN

+0.01

–0.02

0.5

Cathode Index Band

Dimensions in mm

Pin dimension does not include trim burr

Ø2.50±0.2

Cathode index band

Type mark

Pin treatment Pb-free. Device composition

compliant with the RoHS directive.

The body is intentionally small, with the expectation that the product will

be overmolded in the application where used. For this reason, the use

of the diode is not recommended unless it is overmolded. Overmolding

is required to insure insulation against voltage at the surface, heat

dissipation, and to protect against penetration of moisture.

An epoxy resin should be used for the overmolding. It must have

superior adhesion to the surface of the product body, thermal conduction,

protection against penetration of moisture, and must have low distortion

when expanding and contracting while the product is being used in the

application.

Caution for Use

1. Body: Plastic, epoxy resin

2. Pins: Cu wire

Ag plated

SANKEN ELECTRIC CO., LTD.

SHV06JN-DS

High Voltage Rectifier Diode

SHV-06JN

December 5, 2006

• The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the

latest revision of the document before use.

• Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the prod-

ucts herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or

any other rights of Sanken or any third party which may result from its use.

• Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semicon-

ductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures

including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device

failure or malfunction.

• Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equip-

ment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.).

When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and

its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever

long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales

representative to discuss, prior to the use of the products herein.

The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required

(aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited.

• In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the

degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the

load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general,

derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such

as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses,

instantaneous values, maximum values and minimum values must be taken into consideration.

In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of

derating of junction temperature affects the reliability significantly.

• When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically

or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance

and proceed therewith at your own responsibility.

• Anti radioactive ray design is not considered for the products listed herein.

• Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribu-

tion network.

• The contents in this document must not be transcribed or copied without Sanken's written consent.