•Complies with SCSI, SCSI-2 and
SPI-2 Standards
•3pF Channel Capacitance during
Disconnect
•100µA Supply Current in
Disconnect Mode
•Meets SCSI Hot Plugging Capability
•−400mA Sourcing Current for
Termination
•+400mA Sinking Current for Active
Negation
•Logic Command Disconnects all
Termination Lines
•Trimmed Termination Current to 5%
•Trimmed Impedance to 5%
•Current Limit and Thermal
Shutdown Protection
The UC5613 provides 9 lines of active termination for a SCSI (Small Com-
puter Systems Interface) parallel bus. The SCSI standard recommends ac-
tive termination at both ends of the cable segment.
The UC5613 provides a disconnect feature which, when opened or driven
high, disconnects all terminating resistors and disables the regulator
greatly reducing standby power. The output channels remain high imped-
ance even without Termpwr applied. A low channel capacitance of 3pF al-
lows units at interim points of the bus to have little or no effect on the signal
integrity.
The UC 5613 is pin- for-pin compatible with i ts predecessor, the UC5603 - 9
line Acti ve Termin ator. The on ly fun ctio nal differenc e betw een the UC5613
and UC5603 is the absence of the negative clamps. Parametrically, the
UC56 13 ha s a 5% tol eran ce o n im peda nce and current compared to a 3%
tolerance on the UC5603. Custom power packages are utilized to allow
normal operation at full power (1.2 watts).
Internal circuit trimming is utilized, first to trim the impedance to a 5% toler-
ance; then, the output current is trimmed to a 5% tolerance. The output
curre nt trim i s set as c lose a s possibl e to the m aximum value of the SCSI
specification which maximizes the noise margin for fast SCSI operation.
Other features include thermal shutdown and current limit.
This device is offered in low thermal resistance versions of the industry
standard 16 pin narrow body SOIC, 16 pin ZIP (zig-zag in line package),
and 24 pin TSSOP.
UC5613
9-Line Low Capacitance SCSI Active Terminator
FEATURES DESCRIPTION
BLOCK DIAGRAM
Circuit Design Patente d
3/97
UDG-94003-1
ABSOLUTE MAXIMUM RATINGS
Termpwr Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7V
Signal Line Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +7V
Regulator Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5A
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to +150°C
Lead Temperature (Soldering, 10 Sec.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C
RECOMMENDED OPERATING CONDITIONS
Termpwr Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8V to 5.25V
Signal Line Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +5V
Disconnect Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to Termpwr
CONNECTION DIAGRAMS
DIL-16 (Top View)
N or J Package
UC5613
* DP pack ag e pi n 5 se rve s as sig na l gro un d; pins 4, 12, 13
serve as heatsink/ground.
* PWP package pin 5 serves as sig na l gro un d; pins 6, 7, 8, 9,
17, 18, 19, and 20 serve as heatsink/ground.
ZIP-16 (Top View)
Z Package
SOIC-16 (Top View)
DP Package
TSSOP-24 (Top View)
PWP Package
Note: Drawings are not to scal e.
Unles s ot he rw is e sp ec if ie d al l voltag es are w it h res pe ct to G round. Curre nt s are posi-
tive into, negative out of the specified terminal.
Consult Packaging Section of Unitrode Integrated Circuits databook for thermal limita-
tions and consid eration s of pac ka ge s.
2
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS
Supply Current Section
Termpwr Supply Current All termination lines = Open 17 23 mA
All termin ation li ne s = 0. 5V 200 225 mA
Power Down Mode DISCNCT = Open 100 150 µA
Output Sec tio n (Te r mi na tor Li ne s)
Terminator Impedance ∆ILINE = -5mA to -15mA 104.5 110 115.5 Ohms
Output High Voltage TRMPWR = 4V (Note 1) 2.7 2.9 V
Max Ou t put Current VLINE = 0.5V TJ = 25°C -20.3 -21.5 -22.4 mA
0°C < TJ < 70°C -19.8 -21.5 -22.4 mA
Max Ou t put Current VLINE = 0.5V, TRMP WR = 4V (N ot e 1) TJ = 25 °C -19.5 -21.5 -22.4 mA
0°C < TJ < 70°C -19.0 -21.5 -22.4 mA
VLINE = 0.2V , TRMPWR = 4V to 5.25V 0°C < TJ < 70°C -21.6 -24.0 -25.4 mA
Outpu t Le ak ag e DISCNCT = 4V TRMPWR = 0V to 5.25V
REG = 0V VLINE = 0 to 4V 10 400 nA
VLINE = 5.25V 100 µA
TRMPWR = 0V to 5.25V, REG = Open
VLINE = 0V to 5.25V 10 400 nA
Output Capacitance DISCNCT = Open, DP Package (Note 2) 3 4.5 pF
Regulator Section
Regulator Output Voltage 2.8 2.9 3 V
Regulator Output Voltage All Termination Lines = 5V 2.8 2.9 3 V
Line Regulation TRMPWR = 4V to 6V 10 20 mV
Load Regulation IREG = +100mA to -100mA 20 50 mV
Drop Out Voltage All Termination Lines = 0.5V 0.7 1 V
Short Circui t Curre nt VREG = 0V -200 -400 -600 mA
Sinking Current Capability VREG = 3. 5V 200 400 600 mA
Thermal Shutdown 170 °C
Thermal Shutdown Hysteresis 10 °C
Disconnect Section
Disconnect Threshold 1.3 1.5 1.7 V
Threshold Hysteresis 100 160 250 mV
Input Current DISCNCT = 0V 10 15 µA
ELECTRICAL CHARACTERISTICS Unles s othe rwise st at ed, th ese sp ecif icat ions apply for TA = 0°C to 70°C.
TRMPWR = 4.75V, DISCNCT = 0V. TA = TJ.
UC5613
Note 1: Measu rin g ea ch term in at io n li ne while ot he r 8 are lo w (0.5 V).
Note 2: Guara nt ee d by des ig n. Not 10 0% tes te d in pr od uc ti on .
Figure 1: Typical SCSI Bus Configurations Utilizing 2 UC5613 Devices
APPLICATION INFORMATION
UDG-94007-1
3
Figure 2: Typical Wid e SCSI Bus Confi gu r ati on s Util iz in g 3 UC56 13 Devi ce s.
UC5613
UDG-94008-1
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (6 03) 424-2410 • FAX (603) 424-3460
APPLICATION INFORMATION (con t.)
4
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty . Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCT OR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICA TIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1999, Texas Instruments Incorporated
