SNAP-IN MOUNTING HIGH PERFOR-
MANCE IEC CONNECTOR FILTERS
COMPONENTS
ELECTRICAL SCHEMATIC
2-7
SERIES
SPECIFICATIONS
20 dB
0 dB 10K
60 dB
80 dB
40 dB
100K 1M 10M
INSERTION LOSS (TYPICAL)
03GENG3E
06GENG3E
G
N
L
E
L
N
IRCx
Cy
Cy
G'
D
L
O
A
N'
L'
1. Snap-in mounting type to reduce labor cost.
Compact and reliable at low cost.
2. Bleeder resistor can be added with suffix "-R"
on part numbers,except G3H,G3V,W3V,G3J,W3J,types.
3. Bleeder resistor can be added with suffix "-R" on part numbers.
4. Optional side snap-in mounting clip type with suffix (H) on part
numbers.
5
6. With optional Y-Cap from 100pF to 3300pF.
. All part numbers are UL recongnized, CSA certified and VDE
approved.
1. Maximum leakage current each
line-to-ground @ 115VAC 60Hz: 0.2mA
@ 250VAC 50Hz: 0.4mA
2. Hipot rating (one minute)
line-to-ground: 2250VDC
line-to-line: 1450VDC
3. Operating frequency: 50/60Hz
4. Rated voltage: 115/250VAC
MINIMUM INSERTION LOSS IN dB
COMMON MODE
COMMON MODE
DIFF. MODE
DIFF. MODE
D
VE
UL, CSA approved to 4A 115/250V
UL, CSA approved to 8A 115/250V
UL, CSA approved to 13A 115/250V
CURRENT FREQUENCY-MHz
RATING .15 .50 1.0 5.0 10 30
1A 28 35 38 38 40 40
3A 20 25 30 38 40 40
6A 12 18 24 35 40 40
6A (G3Q) 15 20 24 35 40 55
10A 4 10 13 28 35 40
10A (G3C) 10 15 15 25 30 35
10A (G3Q) 10 12 15 30 32 45
15A 4 10 13 28 35 40
20A 8 10 15 25 30 35
COMMON MODE (L-G) IN 50 OHM SYSTEM
20GENG3E DIFF.MODE
100K
40 dB
20 dB
0 dB 10K
80 dB
60 dB
1M 10M
COMMON MODE
VDE approved to 16A/250V
***
VDE approved to 8A/250V
VDE approved to 10A/250V
***
R: 1M /-R ONLY
*
INTRODUCTIONS
01GENG3E/W3E/-R 6.5
03GENG3E/W3E/-R 2.5
03GENW3ES/-R 2.5
03GENG3Q/W3Q/-R 4
06GENG3E/W3E/-R 0.8
06GENG3Q/W3Q/-R 1.5
0.1 2200 1M
06GENW3ES/-R 0.8
10GENG3E/W3E/-R 0.2
10GENG3C/W3C/-R 0.4
10GENG3Q/W3Q/-R 0.3
10GENW3ES/-R 0.2
15GENG3E/W3E/-R 0.2
20GENG3E/W3E/-R 0.3
PART NO. Cx (uF) L (mH) Cy (pF) R ( )
*
**
**
IEC INLET FILTERS
2-8
NG3E, NG3C, NG3Q (Optional wire type)
NG3E(H), NG3C(H), NG3Q(H) (Optional wire type)
UNIT: INCH
mm
MECHANICAL CONSTRUCTION
20GENG3E (Optional wire type)
1.04MAX.
SUGGESTED MOUNTING CUTOUT
R0.118MAX.
(MOUNTING FROM REVERSE)
3.19MAX.
1.36MAX.
1.496MAX.
0.248X0.031
0.138
2.60MAX. 1.18
66.0MAX.
6.3X0.8
34.5MAX.
38.0MAX.
81.0MAX.
3.5
30.0
26.5MAX.
R4.0MAX.
26.5-0
+0.5
+0.02
1.043-0
36.0-0
+0.5
1.417-0
+0.02
1.575 MAX.
BLUE
1.12 MAX.
BROWN
G/Y
SUGGESTED MOUNTING CUTOUT
1.22 0.2
L
G
+0.04
0.142 -0.02
N
0.945 0.02
0.84MAX.
31.0 0.5
24.0 0.5
3.6 -0.5
+1.0
40.0 MAX.
28.4 MAX.
21.3MAX.
NW3E
NW3ES
Suggested thickness of mounting panel is from
0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout
1.12 MAX.
1.12 MAX.
28.4 MAX.
28.4 MAX.
1.66MAX.
1.66MAX.
42.16MAX.
42.16MAX.
2.1MAX.
2.1MAX. -
0.142 0.02
-
0.142 0.02
53.4MAX.
53.4MAX. -
3.6 0.5
-
3.6 0.5
L
L
1.22 0.02
1.22 0.02
31.0 0.5
31.0 0.5
G
G
N
N
24.0 0.5
24.0 0.5 0.945 0.02
0.945 0.02
+0.012
+0.012
+0.3
+0.3
-
1.12 0
-
1.12 0
-
28.45 0
-
28.45 0
R0.08MAX.
R0.08MAX.
R2.0MAX.
R2.0MAX.
0.862 0.004 0.862 0.004
21.9 0.1 21.9 0.1
GENG3E
GENG3E(H)
1.16 0.004
SUGGESTED MOUNTING CUTOUT
0.85 0.004
0.0315~0.063
R0.08MAX(2X)
R2.0MAX
29.5 0.1
21.5 0.1
0.8~1.6
0.8~1.6
0.8~1.6
0.0315~0.06
0.0315~0.06
NW3E
21.4MAX.
21.4MAX.
0.84MAX.
0.84MAX.
ALL WIRE LEADS 4.0" LONG MIN.
PCB
PANEL
ASSEMBLY FROM FRONT
+0.04
+0.04
+1.0
+1.0
SUGGESTED MOUNTING CUTOUT
1.12 MAX.
28.4 MAX.
1.66MAX.
42.16MAX.
-
0.142 0.02
-
3.6 0.5
L
1.22 0.02
31.0 0.5
G
N
24.0 0.5
0.945 0.02
+0.012
+0.3
-
1.12 0
-
28.45 0
R0.08MAX.
R2.0MAX.
0.862 0.004
21.9 0.1
0.8~1.6
0.0315~0.06
21.4MAX.
0.84MAX.
+0.04
+1.0
SUGGESTED MOUNTING CUTOUT
NW3ES
IEC INLET FILTERS
