Anti-surge chip resistors ESR series Datasheet Features 1)Exclusive resistive element pattern and laser trimming technology results in significantly improved surge resistance characteristics. 2)2kV to 5kV electrostatic discharge resistance. 3)Superior power ratings. 4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 5)Corresponds to AEC-Q200. Products list Rated power (70) (inch) (W) Size Part No. (mm) Limiting element voltage (V) ESR01 1005 0402 0.20 50 ESR03 1608 0603 0.25 150 ESR10 2012 0805 0.40 150 ESR18 3216 1206 0.5 200 ESR25 3225 1210 0.66 200 Temperature coefficient (ppm / ) 100 100 +500/-250 200 100 200 100 200 100 100 200 100 100 200 100 100 200 Resistance tolerance (%) F ( 1% ) F ( 1% ) J ( 5% ) J ( 5% ) D ( 0.5% ) F ( 1% ) F ( 1% ) J ( 5% ) D ( 0.5% ) F ( 1% ) J ( 5% ) D ( 0.5% ) F ( 1% ) J ( 5% ) D ( 0.5% ) F ( 1% ) J ( 5% ) Resistance range () 10R976k (E24/96 series) 1MR2.2M (E24 series) 1R9.1 (E24 series) 10R10M (E24 series) 10R1M (E24/96 series) 1R<10 (E24/96 series) 10R10M (E24/96 series) 1R10M (E24 series) 10R1M (E24/96 series) 1R10M (E24/96 series) 1R10M (E24 series) 10R1M (E24/96 series) 1R10M (E24/96 series) 1R10M (E24 series) 10R1M (E24/96 series) 1R10M (E24/96 series) 1R10M (E24 series) Operating temperature range () Automotive grade available -55 +155 Yes -55 +155 Yes -55 +155 Yes -55 +155 Yes -55 +155 Yes * E24 : Standard products, E96 : Custom products. Part Number Description E S R Part No. ESR (Anti-surge chip resistors) 1 0 Size (mm [inch]) EZ P J Packaging specifications code 01(1005 [0402]) 03(1608 [0603]) 10(2012 [0805]) 18(3216 [1206]) 25(3225 [1210]) www.rohm.com (c) 2016 ROHM Co., Ltd. All rights reserved. Packaging Quantity Part No. Code specifications / Reel ESR01 MZP Paper tape ( 4mm Pitch) 10,000 ESR03 EZP Paper tape ( 4mm Pitch) 5,000 ESR10 EZP Paper tape ( 4mm Pitch) 5,000 ESR18 EZP Paper tape ( 4mm Pitch) 5,000 ESR25 JZP Embossed tape ( 4mm Pitch) 4,000 1/4 Resistance tolerance D ( 0.5% ) F ( 1% ) J ( 5% ) 1 0 0 Nominal resistance Resistance code, 3 or 4 digits. 000 denotes jumper type. Resistance tolerance D,F J Resistance code 4 digits 3 digits EX.) 1 = 1R00 (1%) 1R0 (5%) 10 = 10R0 (0.5%,1%) 100 (5%) 1M = 1004 (0.5%, 1%) 105 (5%) 2016.12 - Rev.G ESR series Datasheet Chip resistor dimensions and markings ESR01/03 ESR10/18/25 <Marking method> There are three or four digits used for the calculation number according to IEC code and "R" is used for the decimal point. (Unit:mm) Part No. (mm) (inch) L W t a b Marking existence ESR01 1005 0402 1.000.05 0.500.05 0.350.05 0.200.10 0.25 +0.05 -0.10 No* ESR03 1608 0603 1.600.10 0.800.10 0.450.10 0.300.20 0.300.20 No* ESR10 2012 0805 2.000.10 1.250.10 0.550.10 0.300.20 0.400.20 Yes ESR18 3216 1206 3.200.15 1.600.15 0.550.10 0.300.25 0.500.25 Yes ESR25 3225 1210 3.200.15 2.500.15 0.550.10 0.300.25 0.500.25 Yes *Only with spuare mark Land pattern example (Unit:mm) Dimensions A B C D ESR01 0.5 1.3 0.5 0.4 ESR03 1.0 2.0 0.8 0.5 ESR10 1.2 2.6 1.15 0.70 ESR18 2.2 4.0 1.5 0.9 ESR25 2.2 4.0 2.3 0.9 Part No. www.rohm.com (c) 2016 ROHM Co., Ltd. All rights reserved. 2/4 2016.12 - Rev.G ESR series Datasheet Derating curve When the ambient temperature exceeds 70C, power dissipation must be adjusted according to the derating curves below. ESR 01 / 03 / 10 / 18 / 25 Characteristics Guaranteed balue Resistor ype Test items Test conditions Resistance See P.1 20 Variation of resistance with temperature See P.1 Measurement +25/-55, +25/+125 Test voltage is the smaller one of or Rated voltage(current)x2.5,(ESR03/10/18/25) 2s Rated voltage(current)x2.0,(ESR01) 2s Maximum overload voltage (2.00.1) Overload A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability (1.00.05) No remarkable abnormality on the appearance. Resistance to soldering heat Rosin-ethanol solution(25% weight) Soldering condition 2455 Duration of immersion 2.00.5s Soldering condition 2605 Duration of immersion 101s Rapid change of temperature (1.00.05) Test temp -55+125 5cycle Damp heat, steady state (3.00.1) 4093(Relative humidity) Test time 1,000h Endurance at 70 (3.00.1) Rated voltage(current),70 1.5h:ON0.5h:OFF Test time 1,000h Endurance (3.00.1) 155 Test time 1000h Resistance to solvent (1.00.05) 235 _E0057 Solvent: 2-propanol (1.00.05) Without mechanical damage such as breaks. Bend strength of the end face plating Static electric characteristics EIAJ ED-4701/300 Test method 304 Voltage 2kV(ESR01) 3kV(ESR03/10/18) 5kV(ESR25) C 100pF R 1.5k Apply cycle Times. Compliance Standard(s) : IEC60115-8 JISC 5201-8 (5.00.05) Maximum overload voltage (Test voltage) ESR01 100V ESR03 200V ESR10 200V ESR18 400V www.rohm.com (c) 2016 ROHM Co., Ltd. All rights reserved. - ESR25 400V 3/4 2016.12 - Rev.G ESR series Datasheet Tape dimensions (Unit : mm) Paper tape Part No. W F ESR01 8.00.3 3.50.05 ESR03 8.00.3 ESR10 ESR18 Part No. ESR01 ESR03 ESR10 ESR18 A0 B0 1.750.1 0.70.1 1.20.1 3.50.05 1.750.1 1.10.1 1.90.1 8.00.3 3.50.05 1.750.1 8.00.3 3.50.05 1.750.1 D0 +0.1 1.5 0 +0.1 1.5 0 1.5 +0.1 0 1.5 +0.1 0 E +0.2 -0.1 +0.1 1.95 -0.05 1.65 P2 P0 P1 4.00.1 2.00.05 2.00.05 MAX1.1 4.00.1 4.00.1 2.00.05 MAX1.1 4.00.1 4.00.1 2.00.05 MAX1.1 4.00.1 4.00.1 2.00.05 MAX1.1 T2 (Unit : mm) Embossed tape Part No. ESR25 W F 8.00.3 3.50.05 D0 +0.1 1.5 0 +0.2 -0.1 +0.15 3.5 -0.05 2.4 E 1.750.1 P0 P1 4.00.1 4.00.1 A0 B0 3.00.1 3.50.1 P2 T2 2.00.05 MAX 1.1 Reel dimensions (Unit : mm) Part No. ESR01 ESR03 ESR10 ESR18 ESR25 www.rohm.com (c) 2016 ROHM Co., Ltd. All rights reserved. A 0 180 -1.5 B +1 60 0 4/4 C +1.0 90 D 130.2 2016.12 - Rev.G Datasheet Notice Precaution on using ROHM Products 1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment(Note 1), aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PAA-E (c) 2016 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreigntrade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PAA-E (c) 2016 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising form the use of any ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this document not is current as of the issuing date and subject to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sales representative. 3. The information contained in this document is provided on an "as in" basis and ROHM does not warrant that all information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting form inaccuracy or errors of or concerning such information. Notice - WE (c) 2016 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet ESR10EZPF - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS ESR10EZPF 5000 5000 Taping inquiry Yes