THIS SPEC IS OBSOLETE
Spec No: 002-08522
Spec Title: MB3793-45 POWER-VOLTAGE MONITORING IC
WITH WATCHDOG TIMER DATASHEET
Replaced by: None
Cypress Semiconductor Corporation • 198 Champion Court • San Jose,CA 95134-1709 • 408-943-2600
Document Number: 002-08552 Rev. *D Revised December 10, 2018
MB3793-45
Power-Voltage Monitoring IC with
Watchdog Timer Datasheet
Description
The MB3793 is an integrated circuit to monitor power voltage; it incorporates a watchdog timer. A reset signal is output when the
power is cut or falls abruptly. When the power recovers normally after resetting, a power-on reset signal is output to microprocessor
units (MPUs). An internal watchdog timer with two inputs for system operation diagnosis can provide a fail-safe function for various
application systems.
Features
• Precise detection of power voltage fall: ±2.5%
• Detection voltage with hysteresis
• Low power dispersion: ICC = 31 μA (reference)
• Internal dual-input watchdog timer
• Watchdog timer halt function (by inhibition pin)
• Independently-set watchdog and reset times
Application
• Arcade Amusement etc.
Model No. Marking Code Detection Voltage
MB3793-45 3793-7 4.5 V
Document Number: 002-08552 Rev. *D Page 2 of 24
MB3793-45
Contents
Description ........ ................ ................ ................ ........... 1
Features ....................................................................... 1
Application ................................................................... 1
1. Pin Assignment ...................................................... 3
2. Pin Description ....................................................... 3
3. Block Diagram .......................... ... ... .... ... ... ... .... ....... 4
4. Block Functions .......... ... ... .... ... ... ... .... ... ... ... .... ... ... . 5
5. Absolute Maximum Ratings ........................... ... ... . 6
6. Recommended Operating Conditions .................. 6
7. Electrical Characteristics ...................................... 7
7.1 DC Characteristics ........................................... 7
7.2 AC Characteristics ........................................... 7
8. Timing Diagram ...................................................... 8
8.1 Basic Operation (Positive Clock Pulse) ........... 8
8.2 Basic Operation (Negative Clock Pulse) .......... 9
8.3 Single-Clock Input Monitoring (Positive Clock
Pulse) .................................................................... 10
8.4 Inhibition Operation (Positive Clock Pulse)..... 11
8.5 Clock Pulse Input Supplementation (Positive
Clock Pulse) .......................................................... 12
9. Operation Sequence ................................ ... ... .... .. 13
10. Typical Characteristics ...................................... 15
11. Application Example .......................................... 18
11.1 Supply Voltage Monitor and Watchdog Timer18
11.2 Supply Voltage Monitor and Watchdog Timer
Stop ...................................................................... 19
11.3 Setting of Compulsory Reset ....................... 19
12. Usage Precaution ............................................... 20
13. Ordering Information ......................................... 20
14. RoHS Compliance Information ......................... 20
15. Package Dimensions ......................................... 21
16. Major Changes ................................................... 23
Sales, Solutions, and Legal Information ................. 24
Document Number: 002-08552 Rev. *D Page 3 of 24
MB3793-45
1. Pin Assignment
2. Pin Description
Pin No. Symbol Description
1 RESET Outputs reset
2 CTW Sets monitoring time
3 CTP Sets power-on reset hold time
4 GND Ground
5V
CC Power supply
6 INH Inhibits watchdog timer function
7 CK2 Inputs clock 2
8 CK1 Inputs clock 1
(SOE008)
CTW
CTP
GND VCC
INH
CK2
CK1
(TOP VIEW)
1
2
3
4
8
7
6
5
(SOB008)
RESET
Document Number: 002-08552 Rev. *D Page 4 of 24
MB3793-45
3. Block Diagram
I1 = 3 μA
..I2 = 30 μA
..
R1 =
650 kΩ
..
3
1
6
2
8
7
5
4
CTP
To VCC of all blocks
Pulse generator 1
Watchdog
timer
Reference
voltage
generator
To GND of
all blocks
Pulse generator 2
Output circuit
Logic circuit
RESET
INH
CTW
CK1
CK2
VCC
GND
Comp.S
−
+
VS
VREF = 1.24 V
..
R2 =
240 kΩ
..
Document Number: 002-08552 Rev. *D Page 5 of 24
MB3793-45
4. Block Functions
1. Comp. S
Comp. S is a comparator with hysteresis to compare the reference voltage with a voltage (VS) that is the result of dividing the power
voltage (VCC) by resistors R1 and R2. When VS falls below 1.24 V, a reset signal is output. This function enables the MB3793 to detect
an abnormality within 1 μs when the power is cut or falls abruptly.
2. Output Circuit
The output circuit has a comparator to control the reset signal (RESET) output. When the voltage at the CTP pin for setting the
power-on reset hold time exceeds the threshold voltage, resetting is canceled.
Since the reset (RESET) output buffer has the CMOS organization, no pull-up resistor is needed.
3. Pulse Generator
The pulse generator generates pulses when the voltage at the CK1 and CK2 input clock pins changes to High from Low level
(positive-edge trigger) and exceeds the threshold voltage; it sends the clock signal to the watchdog timer.
4. Watchdog Timer
The watchdog timer can monitor two clock pulses. Short-circuit the CK1 and CK2 clock pins to monitor a single clock pulse.
5. Inhibition Pin
The inhibition (INH) pin forces the watchdog timer on/off. When this pin is High level, the watchdog timer is stopped.
6. Logic Circuit
Logic circuit controls charging and discharging of the power-on reset hold time setting capacity (CTP) on a signal of Comp.S and
Watchdog timer.
Document Number: 002-08552 Rev. *D Page 6 of 24
MB3793-45
5. Absolute Maximum Ratings
* : The voltage is based on the ground voltage (0 V).
WARNING:
1.Semiconductor devices may be permanently damaged by application of stress (including, without limitation, voltage, current or
temperature) in excess of absolute maximum ratings.Do not exceed any of these rating s.
6. Recommended Operating Conditions
* : The watchdog timer monitor time range depends on the rating of the setting capacitor.
WARNING:
1.The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the
device's electrical characteristics are warranted when the device is operated under these conditions.
2.Any use of semiconductor devices will be under their recommended operating condition.
3.Operation under any conditions other than these conditions may adversely affect reliability of device and could result in device failure.
4.No warranty is made with respect to any use, operating conditions or co mbinations not represented on this data sheet. If you are
considering application under any conditions other than listed herein, please contact sales representatives beforehand.
Parameter Symbol Conditions Rating Unit
Min Max
Power supply voltage* VCC —−0.3 +7V
Input voltage* CK1 VCK1 —−0.3 VCC + 0.3
( ≤ +7)
V
CK2 VCK2 —
INH IINH —
Reset output voltage* RESET VOL
VOH
—−0.3 VCC + 0.3
( ≤ +7)
V
Reset output current IOL
IOH
—−10 +10 mA
Power dissipation PDTa ≤ +850C — 200 mW
Storage temperature Tstg — −55 +125 0C
Parameter Symbol Conditions Value Unit
Min Typ Max
Power supply voltage VCC —1.25.06.0V
Reset (RESET) output current IOL —0— + 5mA
IOH —−5— 0
Power-on reset hold time setting
capacity
CTP — 0.001 0.1 10 μF
Watchdog-timer monitoring time
setting capacity*
CTW — 0.001 0.01 1 μF
Operating ambient temperature Ta — −40 +25 +85 0C
Document Number: 002-08552 Rev. *D Page 7 of 24
MB3793-45
7. Electrical Characteristics
7.1 DC Characteristics
* : This parameter is guaranteed by design, which is not supported by a final test.
7.2 AC Characteristics
*: The voltage range is 10% to 90% at testing the reset output transition time.
(VCC = +5 V, Ta = +25°C)
Parameter Symbol Conditions Value Unit
Min Typ Max
Power current ICC1 After exit from reset — 31 45 μA
Detection voltage VSL VCC falling Ta = +25°C 4.40 4.50 4.60 V
Ta = −40 to +85°C 4.35* 4.50 4.65*
VSH VCC rising Ta = +25°C 4.50 4.60 4.70 V
Ta = −40 to +85°C 4.45* 4.60 4.75*
Detection voltage
hysteresis difference
VSHYS VSH - VSL 50 100 150 mV
CK input threshold voltage VCIH —1.4*1.92.5V
VCIL — 0.8 1.3 1.8* V
CK input hysteresis VCHYS — 0.4* 0.6 0.8* V
INH input voltage VIIH —3.5—V
CC V
VIIL —0—0.8V
Input current
(CK1,CK2,INH)
IIH VCK = VCC —01.0μA
IIL VCK = 0 V −1.0 0 — μA
Reset output voltage VOH IRESET = −5 mA 4.5 4.75 — V
VOL IRESET = +5 mA — 0.12 0.4 V
Reset-output minimum power
voltage
VCCL IRESET = +50 μA—0.81.2V
(VCC = +5 V, Ta = +25°C)
Parameter Symbol Conditions Value Unit
Min Typ Max
Power-on reset hold time tPR CTP = 0.1 μF80130180ms
Watchdog timer monitoring time tWD CTW = 0.01 μF
CTP = 0.1 μF
7.5 15 22.5 ms
Watchdog timer reset time tWR CTP = 0.1 μF 5 10 15 ms
CK input pulse duration tCKW — 500 — — ns
CK input pulse cycle tCKT —20——μs
Reset (RESET) output transition time Rising tr* CL = 50 pF — — 500 ns
Falling tf* CL = 50 pF — — 500 ns
Document Number: 002-08552 Rev. *D Page 8 of 24
MB3793-45
8. Timing Diagram
8.1 Basic Operation (Positive Clock Pulse)
CTP
RESET
INH
CTW
CK1
CK2
VSH
VCC
VSL
Vth
VH
VL
(1) (2) (3) (4)(5) (5) (6) (7) (8) (9) (10) (11) (12) (13)
tPR tWD tPR
tWR
tCKW
tCKT
Document Number: 002-08552 Rev. *D Page 9 of 24
MB3793-45
8.2 Basic Operation (Negative Clock Pulse)
CTP
RESET
INH
CTW
CK1
CK2
VSH
VCC
VSL
Vth
VH
VL
tPR tWD tPR
tWR
tCKW
tCKT
(1) (2) (3) (4)(5) (5) (6) (7) (8) (9) (10) (11) (12) (13)
Document Number: 002-08552 Rev. *D Page 10 of 24
MB3793-45
8.3 Single-Clock Input Monitoring (Positive Clock Pulse)
CTP
RESET
CTW
CK1
Vth
VH
VL
CK2
tWR
tWD
tCKT
tCKW
Note : The MB3793 can monitor only one clock.
The MB3793 checks the clock signal at every other input pulse.
Therefore, set watchdog timer monitor time tWD to the time that allows the MB3793
to monitor the period twice as long as the input clock pulse.
Document Number: 002-08552 Rev. *D Page 11 of 24
MB3793-45
8.4 Inhibition Operation (Positive Clock Pulse)
Document Number: 002-08552 Rev. *D Page 12 of 24
MB3793-45
8.5 Clock Pulse Input Supplementation (Positive Clock Pulse)
CTW
CK1
CK2
VH
VL
tCKT
tCKW *1
*2
Note : The MB3793 watchdog timer monitors Clock1 (CK1) and Clock2 (CK2) pulses alternately.
When a CK2 pulse is detected after detecting a CK1 pulse, the monitoring time setting capacity
(CTW) switches to charging from discharging.
When two consecutive pulses occur on one side of this alternation before switching, the second
pulse is ignored.
In the above figure, pulse *1 and *2 are ignored.
Document Number: 002-08552 Rev. *D Page 13 of 24
MB3793-45
9. Operation Sequence
1. Positive Clock Pulse Input
Refer to “8.1 Basic Operation (Positive Clock Pulse)” under “8. Timing Diagram”
2. Negative Clock Pulse Input
Refer to “8.2 Basic Operation (Negative Clock Pulse)” under “8. Timing Diagram”
The MB3793 operates in the same way whether it inputs positive or negative pulses.
3. Clock Monitoring
To use the MB3793 while monitoring only one clock, connect clock pins CK1 and CK2.
Although the MB3793 operates basically in the same way as when monitoring two clocks, it monitors the clock signal at every other
input pulse.
Refer to “8.3 Single-Clock Input Monitoring (Positive Clock Pulse)” under “8. Timing Diagram”
4. Description of Operations
The numbers given to the following items correspond to numbers (1) to (13) used in “8. Timing Diagram”
(1) The MB3793 outputs a reset signal when the supply voltage (VCC) reaches about 0.8 V (VCCL)
(2) If VCC reaches or exceeds the rise-time detected voltage VSH, the MB3793 starts charging the power-on reset hold time setting
capacitor CTP. At this time, the output remains in a reset state. The VSH value is 4.60 V (Typ) .
(3) When CTP has been charged for a certain period of time TPR (until the CTP pin voltage exceeds the threshold voltage (Vth) after
the start of charging), the MB3793 cancels the reset (setting the RESET pin to “H” level from “L” level).
The Vth value is about 3.6 V with VCC = 5.0 V
The power-on reset hold time tPR is set with the following equation:
tPR (ms) ≈ A × CTP (μF)
The value of A is about 1300 with VCC = 5.0 V. The MB3793 also starts charging the watchdog timer monitor time setting capacitor
(CTW).
(4) When the voltage at the watchdog timer monitor time setting pin CTW reaches the “H” level threshold voltage VH, the CTW switches
from the charge state to the discharge state.
The value of VH is always about 1.24 V regardless of the detected voltage.
(5) If the CK2 pin inputs a clock pulse (positive edge trigger) when the CTW is being discharged in the CK1-CK2 order or
simultaneously, the CTW switches from the discharge state to the charge state.
The MB3793 repeats operations (4) and (5) as long as the CK1/CK2 pin inputs clock pulses with the system logic circuit operating
normally.
(6) If no clock pulse is fed to the CK1 or CK2 pin within the watchdog timer monitor time tWD due to some problem with the system
logic circuit, the CTW pin is set to the “L” level threshold voltage VL or less and the MB3793 outputs a reset signal (setting the
RESET pin to “L” level from “H” level).
The value of VL is always about 0.24 V regardless of the detected voltage.
The watchdog timer monitor time tWD is set with the following equation:
tWD (ms) ≈ B × CTW (μF) + C × CTP (μF)
The value of B is hardly affected by the power supply voltage; it is about 1500 with VCC = 5.0 V.
The value in C is about 3 which is tremendously smaller than the value in B. For this reason, it is possible to simplify the formula
as below when CTP/CTW ≈ 10 or less. tWD (ms) ≈ B × CTW (μF)
(7) When a certain period of time tWR has passed (until the CTP pin voltage reaches or exceeds Vth again after recharging the CTP),
the MB3793 cancels the reset signal and starts operating the watchdog timer.
The watchdog timer monitor reset time tWR is set with the following equation:
tWR (ms) ≈ D x CTP (μF) The value of D is 100
with VCC = 5.0 V.
The MB3793 repeats operations (4) and (5) as long as the CK1/CK2 pin inputs clock pulses. If no clock pulse is input, the
MB3793 repeats operations (6) and (7).
(8) If VCC is lowered to the fall-time detected voltage (VSL) or less, the CTP pin voltage decreases and the MB3793 outputs a reset
signal (setting the RESET pin to “L” level from “H” level). The value of VSL is 4.50 V (Typ) .
(9) When VCC reaches or exceeds VSH again, the MB3793 starts charging the CTP.
(10) When the CTP pin voltage reaches or exceeds Vth, the MB3793 cancels the reset and restarts operating the watchdog timer.
It repeats operations (4) and (5) as long as the CK1/CK2 pin inputs clock pulses.
Document Number: 002-08552 Rev. *D Page 14 of 24
MB3793-45
(11) Making the inhibit pin active (setting the INH pin to “H” from “L”) forces the watchdog timer to stop operation.
This stops only the watchdog timer, leaving the MB3793 monitoring VCC (operations (8) to (10)).
The watchdog timer remains inactive unless the inhibit input is canceled.
The inhibition (INH) pin must be connecting a voltage of more low impedance, to evade of the noise.
(12) Canceling the inhibit input (setting the INH pin to “L” from “H”) restarts the watchdog timer.
(13) The reset signal is output when the power supply is turned off to set VCC to VSL or less.
1. Equation of Time-Setting Capacitances (CTP and CTW) and Set Time
tPR [ms] ≈ A × CTP [μF]
tWD [ms] ≈ B × CTW [μF] + C × CTP [μF]
However, when CTP/CTW ≈ 10 or less, tWD [ms] ≈ B × CTW [μF]
tWR [ms] ≈ D × CTP [μF]
Values of A, B, C, and D
Note: The width of value of tPR, tWD and tWR becomes the same ratio as width (Min, Max) of each specifi-
cation value.
2. Example (when CTP = 0.1 μF and CTW = 0.01 μF)
A B C D Remark
1300 1500 3 100 VCC = 5.0 V
Time
(ms)
Symbol VCC = 5.0 V
tPR 130
tWD 15
tWR 10
Document Number: 002-08552 Rev. *D Page 15 of 24
MB3793-45
10. Typical Characteristics
45
40
35
30
25
20
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
MB3793
VINH VCC
(VINH = 0 V)
Ta = +25 °C
Ta = +85 °C
Ta = -40 °C
0
012345678910
0.1
0.2
0.3
0.4
0.5
0.6
4.3
-20-40 0 +20 +40 +60 +80 +100 +120
4.4
4.5
4.6
4.7
4.8
VSH
VSL
0 -1 -2-3 -4-5 -6-7 -8-9-10
Ta = +25 °C
Ta = +85 °C
Ta = -40 °C
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
ICC - VCC characteristic s
Power current
ICC (μA)
Power voltage VCC (V)
Watchdog timer monitoring
Detection voltage
VSH and VSL (V)
Operating ambient temperature Ta (°C)
Reset output current I RESET (mA)
Reset output voltage
V RESET (V)
V RESET - I RESET characteristics
(P-MOS side) V RESET - I RESET characteristics
(N-MOS side)
Reset output voltage
V RESET (V)
Reset output current I RESET(mA)
VSH, VSL - Ta characteristics
fCK= 1 kHz, Duty = 10%
VL = 0 V/VH = VCC
CTW = 0.01 μF, CTP = 0.1 μF
Document Number: 002-08552 Rev. *D Page 16 of 24
MB3793-45
7
6
5
4
3
2
1
0
01234567
Ta = +85 °C
Ta = +25 °C
Ta = -40 °C
-40 -20 0 +20 +40 +60 +80 +100 +120
0
20
40
60
80
100
120
140
160
180
200
220
240
260
at VCC = 5.0 V
−40 −20 0 +20 +40 +60 +80 +100 +120
0
2
4
6
8
10
12
14
16
18
20
22
24
26
at VCC = 5.0 V
−40 −20 0 +20 +40 +60 +80 +100 +120
0
2
4
6
8
10
12
14
16
18
20
22
24
26
at VCC = 5.0 V
VRESET - VCC characteristics
Power voltage VCC (V)
Reset output voltage
VRESET (V)
Pull-up resistance: 100 kΩ
tPR - Ta characteristics
Operating ambient temperature Ta (°C)
Power-on reset hold time
tPR (ms)
tWR - Ta characteristics tWD - Ta characteristics
Operating ambient temperature Ta (°C) Operating ambient temperature Ta (°C)
Watchdog timer reset time
tWR (ms)
Watchdog timer monitoring time
tWD (ms)
Document Number: 002-08552 Rev. *D Page 17 of 24
MB3793-45
104
103
102
101
1
10 −1
10−410−310−210−1110
1102
Ta = −40 °C
Ta = +25 °C
Ta = +85 °C
103
102
101
1
10−1
10−410−310−210−1110
1102
10−2
Ta = −40 °C
Ta = +25 °C
Ta = +85 °C
103
102
101
1
10−1
10−410−310−210−1110
1
10−5
Ta = −40 °C
Ta = +25 °C
Ta = +85 °C
CTP = 0.01 μF
104
10
3
10
2
10
1
1
10
−1
10
−4
10
−3
10
−2
10
−1
110
1
10
−5
C
TP
= 0.01 μF
C
TP
= 0.1 μF
C
TP
= 1 μF
tPR - CTP characteristics tWR - CTP characteristics
Power-on reset hold time
tPR (ms)
Power-on reset time setting capacitance
CTP (μF)
Power-on reset time setting capacitance
CTP (μF)
tWD - CTW characteristics tWD - CTW characteristics
Watchdog timer monitoring time
tWD (ms)
Watchdog timer monitoring time setting capacitance
CTW (μF)
Watchdog timer monitoring time
tWD (ms) Watchdog timer reset time
tWR (ms)
Watchdog timer monitoring time setting capacitance
CTW (μF)
Document Number: 002-08552 Rev. *D Page 18 of 24
MB3793-45
11. Application Example
11.1 Supply Voltage Monitor and Watchdog Timer
11.1.1 1-Clock Monitor
11.1.2 2-Clock Monitor
5
2
3
6
4
7
8
1
RESET VCC
RESET
CK
GND
GND
GND
CTW*CTP*
VCC
VCC
CTW
CTP CK1
CK2INH
MB3793
* : Use a capacitor with less leakage current.
Microprocessor
2
3
6
1
8
7
4
5
VCC
CTW*CTP*
GND
INH GND
VCC
CTP
CTW RESET
CK1
CK2
RESET
CK
GND
VCC RESET
CK
GND
VCC
MB3793
* : Use a capacitor with less leakage current.
Microprocessor1 Microprocessor2
Document Number: 002-08552 Rev. *D Page 19 of 24
MB3793-45
11.2 Supply Voltage Monitor and Watchdog T imer Stop
11.3 Setting of Compulsory Reset
GND
CTW*CTP*
VCC
RESET VCC
CK
GND
RESET VCC
CK
GND
HALT
HALT
5
2
3
6
4
7
8
1
RESET
GND
VCC
INH
CTW
CK1
CK2
CTP
MB3793
* : Use a capacitor with less leakage current.
Microprocessor1 Microprocessor2
5
2
3
6
4
7
8
1
RESET VCC
RESET
CK
GND
GND
GND
CTW
*CTP
*
RESIN
10 kΩ
VCC
VCC
CTW
CTP CK1
CK2INH
MB3793
* : Use a capacitor with less leakage current.
It is possible for the RESET pin to fix to “L” if the CTP pin is short-circuited to GND.
Take care not to change the value of the CTP capacity because of the influence of Tr that is used at
the time.
Microprocessor
Document Number: 002-08552 Rev. *D Page 20 of 24
MB3793-45
12. Usage Precaution
1. Do Not Configure the IC over the Maximum Ratings
If the lC is used over the maximum ratings, the LSl may be permanently damaged.
It is preferable for the device to normally operate within the recommended usage conditions. Usage outside of these conditions can
have a bad effect on the reliability of the LSI.
2. Use the Devices within Recomm ended Operating Conditions
The recommended operating conditions are under which the LSl is guaranteed to operate.
The electrical ratings are guaranteed when the device is used within the recommended operating conditions and under the conditions
stated for each item.
3. Printed Circuit Board Ground Line s should be Set Up with Consideration for Common Impedance
4. T ake Appropriate Measures Against Static Electricity
• Containers for semiconductor materials should have anti-static protection or be made of conductive material.
• After mounting, printed circuit boards should be stored and shipped in conductive bags or containers.
• Work platforms, tools, and instruments should be properly grounded.
• Working personnel should be grounded with resistance of 250 kΩ to 1 MΩ between body and ground.
5. Do Not Apply Negative Voltages
The use of negative voltages below –0.3 V may create parasitic transistors on LSI lines, which can cause malfunctions.
13. Ordering Information
14. RoHS Compliance Information
The LSI products of Spansion with “E1” are compliant with RoHS Directive , and has observed the standard of lead,
cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB) , and polybrominated diphenyl ethers
(PBDE) .
The product that conforms to this standard is added “E1” at the end of the part number.
Part Number Package Remarks
MB3793-45PF 8-pin plastic SOP
(SOE008) –
MB3793-45PNF 8-pin plastic SOP
(SOB008) –
Document Number: 002-08552 Rev. *D Page 21 of 24
MB3793-45
15. Package Dimensions
$//',0(16,216$5(,10,//,0(7(5
',0(16,21,1*$1'72/(5$1&,1*3(5$60(<0
',0(16,21,1*',1&/8'(02/')/$6+',0(16,21,1*('2(6127,1&/8'(
,17(5/($')/$6+253527586,21,17(5/($')/$6+253527586,216
6+$//127(;&(('PP3(56,'('DQG(',0(16,21$5('(7(50,1('
$7'$780+
7+(3$&.$*(7230$<%(60$//(57+$17+(3$&.$*(%27720
',0(16,21,1*'DQG($5('(7(50,1('$77+(287(50267
(;75(0(62)7+(3/$67,&%2'<(;&/86,9(2)02/')/$6+
7+(%$5%8556*$7(%8556$1',17(5/($')/$6+%87,1&/8',1*
$1<0,60$7&+%(7:((17+(723$1'%277202)7+(3/$67,&%2'<
'$7806$%72%('(7(50,1('$7'$780+
1,67+(0$;,080180%(52)7(50,1$/326,7,216)257+(63(&,),('
3$&.$*(/(1*7+
7+(',0(16,21$33/<727+()/$76(&7,212)7+(/($'%(7:((1PP
72PP)5207+(/($'7,3
',0(16,21E'2(6127,1&/8'(7+('$0%$53527586,21$//2:$%/(
'$0%$53527586,216+$//%(PP727$/,1(;&(662)7+(E',0(16,21
$70$;,0800$7(5,$/&21',7,21
7+('$0%$50$<127%(/2&$7('217+(/2:(55$',862)7+()227
7+,6&+$0)(5)($785(,6237,21$//),7,612735(6(177+(1$3,1
,'(17,),(50867%(/2&$7(':,7+,17+(,1'(;$5($,1',&$7('
$,6'(),1('$67+(9(57,&$/',67$1&()5207+(6($7,1*3/$1(72
7+(/2:(6732,17217+(3$&.$*(%2'<(;&/8',1*7+(/,'$1'25
7+(50$/(1+$1&(0(1721&$9,7<'2:13$&.$*(&21),*85$7,216
127(6
L11.25 REF
L
c
0.45
0.13
0.60 0.75
0.20
NOM.MIN.
7.80 BSC
E
0°
D
A
1A
6.35 BSC
0.05
SYMBOL
MAX.
8°
2.25
0.20
ș
E15.30 BSC
b0.39 0.47 0.55
e1.27 BSC
DIMENSION
L20.25 BSC
11. JEDEC SPECIFICATION NO. REF : N/A
D
4
5
E1 E
0.40 CA-B D
A
A1
10
DETAIL A
e0.10 C
SEATING
PLANE
b0.13 CA-B D8
SIDE VIEW
TOP VIEW
b
SECTION A-A'
c
L1
L
GAUGE
PLANE
DETAIL A
L2
șA
A'
0.25 H D
;
0.25 H D
㻭㻰
㻯
4
5
INDEX AREA
;
㻮
BOTTOM VIEW
Package Code: SOE008
002-15857 Rev. **
Document Number: 002-08552 Rev. *D Page 22 of 24
MB3793-45
$//',0(16,216$5(,10,//,0(7(5
',0(16,21,1*$1'72/(5$1&,1*3(5$60(<0
',0(16,21,1*',1&/8'(02/')/$6+',0(16,21,1*('2(6127,1&/8'(
,17(5/($')/$6+253527586,21,17(5/($')/$6+253527586,216
6+$//127(;&(('PP3(56,'('DQG(',0(16,21$5('(7(50,1('
$7'$780+
7+(3$&.$*(7230$<%(60$//(57+$17+(3$&.$*(%27720
',0(16,21,1*'DQG($5('(7(50,1('$77+(287(50267
(;75(0(62)7+(3/$67,&%2'<(;&/86,9(2)02/')/$6+
7+(%$5%8556*$7(%8556$1',17(5/($')/$6+%87,1&/8',1*
$1<0,60$7&+%(7:((17+(723$1'%277202)7+(3/$67,&%2'<
'$7806$%72%('(7(50,1('$7'$780+
1,67+(0$;,080180%(52)7(50,1$/326,7,216)257+(63(&,),('
3$&.$*(/(1*7+
7+(',0(16,21$33/<727+()/$76(&7,212)7+(/($'%(7:((1PP
72PP)5207+(/($'7,3
',0(16,21E'2(6127,1&/8'(7+('$0%$53527586,21$//2:$%/(
'$0%$53527586,216+$//%(PP727$/,1(;&(662)7+(E',0(16,21
$70$;,0800$7(5,$/&21',7,21
7+('$0%$50$<127%(/2&$7('217+(/2:(55$',862)7+()227
7+,6&+$0)(5)($785(,6237,21$//),7,612735(6(177+(1$3,1
,'(17,),(50867%(/2&$7(':,7+,17+(,1'(;$5($,1',&$7('
$,6'(),1('$67+(9(57,&$/',67$1&()5207+(6($7,1*3/$1(72
7+(/2:(6732,17217+(3$&.$*(%2'<(;&/8',1*7+(/,'$1'25
7+(50$/(1+$1&(0(1721&$9,7<'2:13$&.$*(&21),*85$7,216
127(6
L11.05 REF
L
c
0.45
0.15
0.60 0.75
0.25
NOM.MIN.
6.00 BSC.
E
0°
D
2A
A
1A
1.30
5.05 BSC.
1.40
0.05
SYMBOL
MAX.
8°
1.50
1.75
0.25
ș
E13.90 BSC
b0.36 0.44 0.52
e1.27 BSC.
DIMENSIONS
L20.25 BSC
h0.40 BSC.
11. JEDEC SPECIFICATION NO. REF : N/A
D
4
5
E1 E
0.20 CA-B D
AA2
A1
10
DETAIL A
e0.10 C
SEATING
PLANE
b0.13 CA-B D
8
SIDE VIEW
TOP VIEW
b
SECTION A-A'
c
L1
L
GAUGE
PLANE
DETAIL A
L2
ș
A
A'
0.25 H D
;
0.25 H D
㻭㻰
㻯
4
5
INDEX AREA
;
h
45°
SIDE VIEW
BOTTOM VIEW
㻮
Package Code: SOB008
002-15856 Rev. **
Document Number: 002-08552 Rev. *D Page 23 of 24
MB3793-45
16. Major Changes
NOTE: Please see “Document History” about later revised information.
Document History
Page Section Change Results
Revision 3.0
--
Company name and layout design change
1 DESCRIPTION Deleted "There is also a mask option that can detect voltages of 4.9 V to 2.4
V in 0.1-V steps."
Document Title: MB3793-45 Power-Voltage Monitoring IC with Watchdog Timer Datasheet
Document Number: 002-08552
Revision ECN Orig. of
Change Submission
Date Description of Change
** - TAOA 01/06/2015 Migrated to Cypress and assigned document number 002-08552.
No change to document contents or format.
*A 5151492 TAOA 03/01/2016 Updated to Cypress template
*B 5611415 HIXT 01/31/2017
Updated Pin Assignment:
Change the package name from FPT-8P-M01 to SOE008
Change the package name from FPT-8P-M02 to SOB008
Updated Ordering Information:
Change the package name from FPT-8P-M01 to SOE008
Change the package name from FPT-8P-M02 to SOB008
Updated Package Dimensions: Updated to Cypress format
Deleted “Marking Format (Lead Free version)”
Deleted “Labeling Sample (Lead free version)”
Deleted “MB3793-45PF, MB3793-45PNF Recommended Conditions of Moisture Sensitivity
Level”
*C 5790329 MASG 06/29/2017 Adapted Cypress new logo.
*D 6406322 YOST 12/10/2018 Obsoleted.
Document Number: 002-08552 Rev. *D Revised December 10, 2018 Page 24 of 24
© Cypress Semiconductor Corporation, 2001-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document,
including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in
the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
MB3793-45
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
ARM® Cortex® Microcontrollers cypress.com/arm
Automotive cypress.com/automotive
Clocks & Buffers cypress.com/clocks
Interface cypress.com/interface
Internet of Things cypress.com/iot
Memory cypress.com/memory
Microcontrollers cypress.com/mcu
PSoC cypress.com/psoc
Power Management ICs cypress.com/pmic
Touch Sensing cypress.com/touch
USB Controllers cypress.com/usb
Wireless/RF cypress.com/wireless
PSoC® Solutions
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6
Cypress Developer Community
Forums | WICED IOT Forums | Projects | Video | Blogs | Training
| Components
Technical Support
cypress.com/support