Microwave Ceramics Filters
Series/Type: B726
The following products presented in this data sheet are being withdrawn.
Ordering Code Substitute Product Date of Withdrawal Deadline Last
Orders Last Shipments
B69812N9156B726 2012-04-27 2012-07-31 2012-10-31
For further information please contact your nearest EPCOS sales office, which will also support you in selecting a
suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales.
Microwave Ceramics Filter B69812N9156B726
2-pole filter for ISM S2G3/2/1
Data sheet
SAW MLIP CER PD 2010-01-20
Please read Cautions and warnings and Page 2 of 6
Important notes at the end of this document.
Modification
P2 17.07.96 Freising
P3 Recommended footprint 29.10.97 Freising
P4 Recommended footprint, component drawing 04.05.99 Keiler
P5 Recommended footprint 29.07.03 Stadler
P6 Standing wave ratio 19.08.03 Freising
A 05.04.04 Freising
B Upgraded to new form 20.01.10 Reichel
Features
SMD filter consisting of coupled resonators with stepped impedances
(NdBa)TiO3 (εr = 88/TCf = 0 ±10 ppm/K) with a coating of copper (10 µm) and tin (>5 µm)
Excellent reflow solderability, no migration effect due to copper/tin metallization
Microwave Ceramics Filter B69812N9156B726
2-pole filter for ISM S2G3/2/1
Data sheet
SAW MLIP CER PD 2010-01-20
Please read Cautions and warnings and Page 3 of 6
Important notes at the end of this document.
Component drawing
Recommended footprint
View from below onto the solder terminals and view from beside
Marking: ‘EPCOS logo’ SC 9156, on top of the filter
G
I/O
I/O G
G
1.5
5
2.5
4.15
1.6
9.30
1.7
1.95
2.55
G
G
1.7 3.0
Microwave Ceramics Filter B69812N9156B726
2-pole filter for ISM S2G3/2/1
Data sheet
SAW MLIP CER PD 2010-01-20
Please read Cautions and warnings and Page 4 of 6
Important notes at the end of this document.
Characteristics
min. typ. max.
Center frequency fc– 915 – MHz
Insertion loss αIL 1.3 2.0 dB
Passband B 26 MHz
Amplitude ripple (peak – peak) ∆α 0.5 1.0 dB
Standing wave ratio SWR 1.5 1.7
Impedance Z 50
Attenuation α
at 818 MHz
at 1026 MHz
35
20
40
25
dB
dB
Maximum ratings
IEC climatic category (IEC 68-1) –40 °C/+90 °C/56
Operating temperature Top –20/+85 °C
Typical passband characteristic
-80 -60 -40 -20 0
0,77
0,78
0,8
0,81
0,83
0,84
0,86
0,87
0,89
0,9
0,92
0,93
0,95
0,96
0,98
0,99
1,01
1,02
1,04
1,05
frequency [GHz]
attenuation [dB]
DB[S12]
DB[S11]
Microwave Ceramics Filter B69812N9156B726
2-pole filter for ISM S2G3/2/1
Data sheet
SAW MLIP CER PD 2010-01-20
Please read Cautions and warnings and Page 5 of 6
Important notes at the end of this document.
Processing information
Wettability acc. to IEC 68-2-58: 75% (after aging)
Soldering requirements
Profile for eutectic
SnPb solder paste
Profile for leadfree
solder paste
Soldering type reflow reflow
Maximum soldering temperature 235 (max. 2 sec.) 260 (max. 2 sec.) °C
(measuring point on top surface of the component) 225 (max. 10 sec.) 250 (max. 10 sec.) °C
Recommended soldering conditions (infrared):
50
100
150
200
250
20-40 sec.
40-80 sec.
within 10 sec.
Time [sec.]
Temp. [°C]
215°C±10°C
50
100
150
200
250
30 sec.
2-3 min.
within 10 sec.
Time [sec.]
Temp. [°C]
245°C±5°C
2.5 °C/s > - 5 °C/s
Delivery mode
Blister tape acc. to IEC 286-3, polyester, grey
Pieces/tape: 1500
2±0.1
4±0.1
1.5+ 0.1
10x4(= 40±0.2)
1.75±0.1
7.5±0.1
A
A
B B
Profile B-B:
Profile A-A:
I/O
16±0.3
0.3
12±0.1 3.1±0.1
max.
max.
7.9±0.1
1.5+ 0.1
9.3±0.1
R0 . 3 m a x.
R0 . 3 m a x .
R0 . 3 m ax .
R0 . 3 m a x .
direction of unreeling
Reel:
diamet er - 330 mm
Tape:
Important notes
Page 6 of 6
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very high
level of operational safety and especially in customer applications in which the malfunction or
failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of the
customer application or other action taken by the customer (e.g. installation of protective circuitry
or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or
failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed
questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
The aforementioned does not apply in the case of individual agreements deviating from the
foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic,
DSSP, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube,
PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer,
SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe
and in other countries. Further information will be found on the Internet at
www.epcos.com/trademarks.