TD62107PG/FG TOSHIBA Bipolar Digital Integrated Circuit Silicon Monolithic TD62107PG,TD62107FG 4ch High-current Darlington Sink Driver The TD62107PG/FG are high-voltage, high-current darlington drivers and enable inputs which can gate the outputs. All units feature integral clamp diodes for switching inductive loads. The TD62107PG/FG have a wide supply voltage range and all input are compatible with TTL and 5-V CMOS. Application include relay, hammer, lamp and stepping moter drivers. Please observe the thermal condition for using. This devices are a product for the Pb free(Sn-Ag). TD62107PG TD62107FG Features * Output current (single output) 750 mA (max) * High sustaining voltage output: 45 V min (TD62107PG) 35 V min (TD62107FG) * Output clamp diodes * Enable inputs E1, E2 * Wide supply voltage range VCC = 4.75 to 7 V * Input compatible with TTL and 5-V CMOS * GND terminal = heat sink * Package type-PG: DIP-16pin * Package type-FG: HSOP-16pin Weight DIP16-P-300-2.54A: 1.11 g (typ.) HSOP16-P-300-1.00: 0.50 g (typ.) Pin Assignment (top view) TD62107PG TD62107FG VCC O1 O2 Heat sink & GND O3 O4 COM 16 15 14 13 12 11 10 9 16 1 E1 2 I1 3 I2 4 5 Heat sink & GND 6 I3 7 I4 8 E2 1 E1 NC Heat sink O2 & GND O3 O4 COM NC 15 14 13 12 11 10 9 2 I1 3 NC 4 5 I2 Heat sink I3 & GND 6 I4 7 E2 8 NC VCC O1 1 2005-03-02 TD62107PG/FG Schematics (each driver) Truth Table I1 O1 I2 O2 I3 O3 I4 O4 Common E1 E2 I1 to I4 O1 to O4 L L L or H Disable OFF L H L or H Disable OFF H L L or H Enable In H H L or H Disable OFF In = I1~I4 E1 E2 Input Equivalent Circuit Output Equivalent Circuit VCC Common Output Input Note: The input and output parasitic diodes cannot be used as clamp diodes. Maximum Ratings (Ta = 25C) Characteristics Supply voltage Output sustaining voltage Rating Unit VCC -0.5 to 17 V PG FG Output current Input voltage Clamp diode reverse voltage Symbol VCE (SUS) Clamp diode forword current 750 mA VIN V 45 VR IF FG V -0.5 to VCC + 0.5 PG Power dissipation -0.5 to 35 IOUT PG FG -0.5 to 45 V 35 500 mA 2.7 (Note 1) PD W 1.4 (Note 2) Operating temperature Topr -40 to 85 C Storage temperature Tstg -55 to 150 C Note 1: On glass epoxy PCB (50 x 50 x 1.6 mm Cu 50%) Note 2: On glass epoxy PCB (60 x 30 x 1.6 mm Cu 30%) 2 2005-03-02 TD62107PG/FG Recommended Operating Conditions (Ta = -40 to 85C) Characteristics Supply voltage Symbol Condition Min Typ. Max Unit VCC 4.75 15 V 0 45 VCE (SUS) 0 35 Tpw = 25 ms, Duty = 75%, 1 Circuit 0 500 Duty = 30% 0 400 Duty = 40% 300 0 VCC 45 35 PG Output sustaining voltage FG Output current IOUT PG FG Input voltage Tpw = 25 ms, 4 Circuit VIN VR IF 500 1.0 0.7 Min Typ. Max 2.0 VCC 0.8 VCE = 45 V, Ta = 75C 100 VCE = 35 V, Ta = 85C 100 PG Clamp diode reverse voltage FG Clamp diode forward current PG Power dissipation PD FG Note1: V Ta = 85C (Note 1) mA V V mA W On Glass Epoxy PCB (60 x 30 x 1.6 mm Cu 30%) Electrical Characteristics (Ta = 25C) Characteristics Input voltage Output current Output voltage Symbol High level VIH Low level VIL High level Test Circuit Test Condition 1 PG Unit V A IOH 2 Low level VOL 3 IOUT = 50 mA 1.3 V High level IIH 4 VIN = 13 V 100 A Low level IIL 5 VIN = 0.4 V -0.3 mA VR = 45 V 100 VR = 35 V 100 FG Input current PG Clamp diode reverse current IR 6 VF 7 IF = 500 mA 2.0 ICCH 4 VCC = 13 V, VIN = 0 V Output open 13 ICCL 5 VCC = 13 V, VIN = 5 V Output open 17 VCC = 5 V, RL = 90 CL = 15 pF, VOUT = 45 V 5 FG VCC = 5 V, RL = 70 CL = 15 pF, VOUT = 35 V 5 PG VCC = 5 V, RL = 90 CL = 15 pF, VOUT = 45 V 5 VCC = 5 V, RL = 70 CL = 15 pF, VOUT = 35 V 5 FG Clamp diode forward voltage Output high Supply current Output low ICC PG Turn-on delay tON Turn-off delay tOFF FG 8 8 3 A V mA s s 2005-03-02 TD62107PG/FG Test Circuit 1. VIH, VIL VCC 2. IOH Open 3. VOL VCC VCC Open IOH IOUT VIH, VIL VCC IIH IOUT VCE VCE 4. IIH, ICCL VIN (ON) 5. IIL, ICCL Open Open VCC ICCH IIL IR Open VIN VOL 6. IR VCC ICCL Open Open VR Open VIN Open 7. VF 8. tON, tOFF Input VCC = 5 V Open VCC VF Open IF VOUT RL Pulse generator Output (Note 1) CL = 15 pF (Note 3) (Note 2) Open Input Condition tf tr 90% 50% Input 10% VIH = 3 V 90% 50% 50 s 10% 0 tOFF tON VOH Output 50% 50% VOL Note 1: Pulse width 50 s, duty cycle 10% Output Impedance 50 , tr 5ns, tf 10 ns Note 2: VIH = 3 V, E1 = VIH, E2 = GND, VCC = 5 V Note 3: CL includes probe and jig capacitance Precautions for Using This IC does not include built-in protection circuits for excess current or overvoltage. If this IC is subjected to excess current or overvoltage, it may be destroyed. Hence, the utmost care must be taken when systems which incorporate this IC are designed. Utmost care is necessary in the design of the output line, VCC, COMMON and GND line since IC may be destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding. 4 2005-03-02 TD62107PG/FG VCE (sat) - IOUT VOUT - VIN 8.0 50 (A) IOUT = 500 mA Output current Output current IOUT 6.0 IOUT (A) VCC = 5 to 17 V 0.4 Ta = 75C 25 -30 0.2 0 0 0.4 0.8 1.2 Output saturation voltage 40 25 20 Ta = 75C 10 0 0 1.6 -30 30 2.0 1.0 VCE (sat) (V) 3.0 Input voltage IOUT - Duty cycle 4.0 5.0 VIN (V) IOUT - Duty cycle 0.8 0.8 Device limit 1 Device limit 1, 2 2 (A) 0.6 0.6 4 Circuit IOUT Output current IOUT (A) 3 3 Recommended limit 0.4 4 Circuit Recommended limit 0.4 Ta = 75C 0.2 30 50 70 Duty cycle Ta = 25C 0.2 30 90 50 (%) 70 Duty cycle PD - Ta 90 (%) PD - Ta 4 4.0 (1) Type-FG on PCB TD62107PG PD (W) (2) Type-FG free air 3 Power dissipation Power dissipation PD (W) 60 x 30 x 1.6 mm Cu 30% 2 (1) 1 0 0 (2) 25 50 75 Ambient temperature 100 Ta 125 3.0 2.0 1.0 0 0 150 (C) 25 50 75 Ambient temperature 5 100 Ta 125 150 (C) 2005-03-02 TD62107PG/FG Package Dimensions Weight: 1.11 g (typ.) 6 2005-03-02 TD62107PG/FG Package Dimensions Weight: 0.50 g (typ.) 7 2005-03-02 TD62107PG/FG About solderability, following conditions were confirmed * Solderability (1) Use of Sn-63Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux RESTRICTIONS ON PRODUCT USE 030619EBA * The information contained herein is subject to change without notice. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. 8 2005-03-02