2.8X0.8mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: AA2810AZGS Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description z 2.8mmX0.8mm right angle SMT LED, 1.2mm thickness. The Green source color devices are made with InGaN z Low power consumption. on Sapphire Light Emitting Diode. z Ideal for backlight and indicator. Static electricity and surge damage the LEDS. z Various colors and lens types available. It is recommended to use a wrist band or anti-electrostatic z Package : 2000pcs / reel. glove when handling the LEDs. z Moisture sensitivity level : level 3. All devices, equipment and machinery must be electrically z RoHS compliant. grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.1(0.0039") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1.Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916 Selection Guide Part No. Dice AA2810AZGS Iv (mcd) [2] @ 20mA Lens Type Green (InGaN) Viewing Angle [1] Min. Typ. 21/2 400 700 110 Water Clear Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25C Symbol Parameter Device Typ. peak Peak Wavelength Green D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 515 nm IF=20mA Green 525 nm IF=20mA Spectral Line Half-width Green 30 nm IF=20mA C Capacitance Green 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.3 4.1 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25C Parameter Green Units Power dissipation 102.5 mW DC Forward Current 25 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40C To +85C Storage Temperature -40C To +85C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916 Green AA2810AZGS SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916 AA2810AZGS Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916 PACKING & LABEL SPECIFICATIONS AA2810AZGS SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kingbright: AA2810AZGS