SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916
2.8X0.8mm RIGHT ANGLE SMD CHIP LED
LAMP
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Part Number: AA2810AZGS Green
Features
z2.8mmX0.8mm right angle SMT LED, 1.2mm thickness.
zLow power consumption.
zIdeal for backlight and indicator.
zVarious colors and lens types available.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Green source color devices are made with InGaN
on Sapphire Light Emitting Diode.
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.0039") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1.Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
2. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AA2810AZGS Green (InGaN) Water Clear 400 700 110°
Iv (mcd) [2]
@ 20mA
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Green 515 nm IF=20mA
λD [1] Dominant Wavelength Green 525 nm IF=20mA
Δλ1/2 Spectral Line Half-width Green 30 nm IF=20mA
C Capacitance Green 45 pF VF=0V;f=1MHz
VF [2] Forward Voltage Green 3.3 4.1 V IF=20mA
IR Reverse Current Green 50 uA VR=5V
Parameter Green Units
Power dissipation 102.5 mW
DC Forward Current 25 mA
Peak Forward Current [1] 150 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916
Green AA2810AZGS
SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916
AA2810AZGS
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAK2450 REV NO: V.2 DATE: APR/13/2011 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: J.Yu ERP: 1201005916
PACKING & LABEL SPECIFICATIONS AA2810AZGS
