INCH-POUND MIL-PRF-39018/1H 20 February 2009 SUPERSEDING MIL-PRF-39018/1G 2 March 2007 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, ELECTROLYTIC (ALUMINUM OXIDE) (POLARIZED), NON-ESTABLISHED RELIABILITY AND ESTABLISHED RELIABILITY STYLES CU12 (UNINSULATED), CU13 (INSULATED), AND CUR13 (INSULATED) STYLE CU12 INACTIVE FOR DESIGN AFTER 23 MARCH 1972 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the capacitors described herein shall consist of this specification sheet and MIL-PRF-39018. Case size A0 A1 A2 A3 A4 A5 A6 Dimensions D .015 L .031 See note 4 .938 .938 1.125 1.375 1.625 2.188 2.688 .281 .375 .375 .375 .375 .375 .375 Inches .002 .008 .015 .031 .032 .140 .250 .281 mm 0.05 0.20 0.38 0.79 0.81 3.56 6.35 7.14 Inches .375 .938 1.125 1.375 1.50 1.625 2.188 2.688 mm 9.53 23.83 28.57 34.92 38.1 41.27 55.58 68.28 FIGURE 1. Styles CU12, CU13, and CUR13 capacitors. AMSC N/A FSC 5910 MIL-PRF-39018/1H NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. These capacitors are not intended to be mounted by their leads. 4. The "D" dimensions for styles CU13 and CUR13 shall be not more than .008 (0.20 mm) larger than the specified bare case diameter. FIGURE 1. Styles CU12, CU13, and CUR13 capacitors - Continued. REQUIREMENTS: Dimensions and configuration: See figure 1. Case: Type - Tubular. Material - Metal. Leads - See figure 1. DC rated voltage: See table I. Reverse voltage: 3.0 volts maximum. Capacitance (Cap.) value: See table I. Cap. tolerance: See table I. Failure rate level (CUR13 only): M, P, R, and S. Operating temperature range: -55C to +85C derated to +125C (see table I). Burn-in (CUR13 only): In accordance with MIL-PRF-39018. DC leakage (DCL): See table I. Equivalent series resistance (ESR): See table I. Low temperature exposure: DCL: See table I. Cap.: See table I. ESR: See table I. Solderability: In accordance with MIL-PRF-39018. Terminal strength: Method 211 of MIL-STD-202, test condition A (3 pounds) and test condition D (3 rotations). 2 TABLE I. Styles CU12, CU13, and CUR13 capacitors. DC rated voltage Cap. ESR DC surge voltage 5 5 5 5 5 5 7 7 7 7 7 7 7 10 10 10 10 10 10 10 10 F 220 270 390 560 820 1000 100 180 220 330 470 680 820 68 82 150 180 270 390 560 680 10 10 10 10 10 10 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 7 7 7 7 7 7 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 1.21 .98 .68 .47 .32 .27 2.65 1.47 1.21 .80 .56 .39 .32 3.90 3.23 1.77 1.47 .98 .68 .47 .39 30 30 30 30 30 30 30 30 30 20 20 20 20 20 20 20 20 20 33 47 82 100 120 150 220 330 390 40 40 40 40 40 40 40 40 40 30 30 30 30 30 30 30 30 30 8.04 5.64 3.23 2.65 2.21 1.77 1.20 .80 .68 10.05 7.05 4.04 3.33 2.76 2.21 1.51 1.00 .85 +85C +125C volts +125C +25C volts 3 See footnotes at end of table. DC leakage +25 C 20 17 12 8 5.5 4.5 38 25 20 14 9.6 6.6 5.5 66 55 30 25 17 12 8 6.6 3 3 4 5 7 10 2 3 3 4 5 7 10 2 2 3 3 4 5 7 10 91 64 36 30 25 20 14 9.1 7.7 2 2 3 3 4 4 5 7 10 +85C and +125C A 18 18 24 30 42 60 12 18 18 24 30 42 60 12 12 18 18 24 30 42 60 12 12 18 18 24 24 30 42 60 Max. ac Case ripple size current 120 Hz at 85C 1/ mA 290 3/ A1 A2 360 3/ A3 520 3/ A4 750 3/ A5 1100 3/ A6 1350 3/ 285 3/ A0 A1 438 3/ A2 527 3/ A3 696 3/ A4 892 3/ A5 1210 A6 1490 181 3/ A0 A0 219 3/ A1 400 A2 475 A3 628 A4 810 A5 1100 A6 1320 A0 164 A0 196 A1 297 A2 353 A3 419 A3 470 A4 607 A5 848 A6 1000 Style CU12 Capacitance tolerance -10 +30 0401 0402 0403 0404 0405 0406 0407 0408 0409 0410 0411 0412 0413 0414 0415 0416 0417 0418 0419 0420 0421 0422 0423 0424 0425 0426 0427 0428 0429 0430 -10 -10 +50 +75 Percent 0501 --0502 --0503 --0504 --0505 --0506 --0507 --0508 --0509 --0510 --0511 --0512 --0513 --0514 --0515 --0516 --0517 --0518 --0519 --0520 --0521 --0522 --0523 --0524 --0525 --0526 --0527 --0528 --0529 --0530 --- Dash number Style CU13 Capacitance tolerance -10 +30 0601 0602 0603 0604 0605 0606 0607 0608 0609 0610 0611 0612 0613 0614 0615 0616 0617 0618 0619 0620 0621 0622 0623 0624 0625 0626 0627 0628 0629 0630 -10 +50 Percent ------------------------------------------------------------- -10 +75 0701 0702 0703 0704 0705 0706 0707 0708 0709 0710 0711 0712 0713 0714 0715 0716 0717 0718 0719 0720 0721 0722 0723 0724 0725 0726 0727 0728 0729 0730 Style CUR13 2/ Capacitance tolerance -10 -10 +50 +75 Percent 1001- --- 11011002- --- 11021003- --- 11031004- --- 11041005- --- 11051006- --- 11061007- --- 11071008- --- 11081009- --- 11091010- --- 11101011- --- 11111012- --- 11121013- --- 11131014- --- 11141015- --- 11151016- --- 11161017- --- 11171018- --- 11181019- --- 11191020- --- 11201021- --- 11211022- --- 11221023- --- 11231024- --- 11241025- --- 11251026- --- 11261027- --- 11271028- --- 11281029- --- 11291030- --- 1130-10 +30 MIL-PRF-39018/1H 7 7 7 7 7 7 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 +85C and +125C 1.51 1.23 .85 .59 .40 .33 3.32 1.84 1.51 1.00 .71 .49 .40 4.86 4.04 2.21 1.84 1.23 .85 .59 .49 +85C Max. Imped. at -55C and 120 Hz TABLE I. Styles CU12, CU13, and CUR13 capacitors - Continued. DC rated voltage +85C F 22 33 47 56 68 100 150 180 12 22 33 47 68 100 120 8.2 12 15 22 33 47 68 4.7 5.6 8.2 12 18 22 33 56 +125C +25C volts 60 60 60 60 60 60 60 60 90 90 90 90 90 90 90 125 125 125 125 125 125 125 175 175 175 175 175 175 175 175 See footnotes at end of table. 50 50 50 50 50 50 50 50 75 75 75 75 75 75 75 100 100 100 100 100 100 100 125 125 125 125 125 125 125 125 9.04 5.03 4.23 3.55 2.92 1.99 1.33 1.11 16.58 9.04 6.03 4.27 2.92 1.99 1.65 24.26 16.54 13.26 9.04 6.03 4.23 2.92 28.22 23.68 10.17 11.05 7.37 6.03 4.02 2.37 +85C and +125C 15.07 10.05 7.05 5.92 4.88 3.32 2.21 1.84 27.63 15.07 10.05 7.05 4.88 3.32 2.76 40.44 27.63 22.10 15.07 10.05 7.05 4.88 56.44 47.37 32.35 22.10 14.74 12.06 8.04 4.74 Max. Imped. at -55C and 120 Hz 140 91 64 54 44 30 20 17 250 140 91 64 44 30 25 360 250 200 140 91 64 44 640 540 360 250 170 140 91 54 DC leakage +25 C 2 3 3 4 4 5 7 10 2 3 3 4 5 7 10 2 3 3 4 5 7 10 2 2 3 3 4 5 7 10 +85C and +125C A 12 18 18 24 24 30 42 60 12 18 18 24 30 42 60 12 18 18 24 30 42 60 12 12 18 18 24 30 42 60 Max. ac ripple current 120 Hz at 85C 1/ mA 134 188 243 286 315 410 571 680 96 153 204 262 337 506 555 82 109 137 179 235 319 417 69 75 105 137 182 214 300 423 Case size Style CU12 Capacitance tolerance -10 +30 A0 A1 A2 A3 A3 A4 A5 A6 A0 A1 A2 A3 A4 A5 A6 A0 A1 A2 A3 A4 A5 A6 A0 A0 A1 A2 A3 A4 A5 A6 0431 0432 0433 0434 0435 0436 0437 0438 0439 0440 0441 0442 0443 0444 0445 0446 0447 0448 0449 0450 0451 0452 0453 0454 0455 0456 0457 0458 0459 0460 -10 -10 +50 +75 Percent 0531 --0532 --0533 --0534 --0535 --0536 --0537 --0538 --0539 --0540 --0541 --0542 --0543 --0544 --0545 --0546 --0547 --0548 --0549 --0550 --0551 --0552 ----0553 --0554 --0555 --0556 --0557 --0558 --0559 --0560 Dash number Style CU13 Capacitance tolerance -10 +30 0631 0632 0633 0634 0635 0636 0637 0638 0639 0640 0641 0642 0643 0644 0645 0646 0647 0648 0649 0650 0651 0652 0653 0654 0655 0656 0657 0658 0659 0660 -10 +50 Percent --------------------------------------------0753 0754 0755 0756 0757 0758 0759 0760 -10 +75 0731 0732 0733 0734 0735 0736 0737 0738 0739 0740 0741 0742 0743 0744 0745 0746 0747 0748 0749 0750 0751 0752 ----------------- Style CUR13 2/ Capacitance tolerance -10 -10 +50 +75 Percent 1031- --- 11311032- --- 11321033- --- 11331034- --- 11341035- --- 11351036- --- 11361037- --- 11371038- --- 11381039- --- 11391040- --- 11401041- --- 11411042- --- 11421043- --- 11431044- --- 11441045- --- 11451046- --- 11461047- --- 11471048- --- 11481049- --- 11491050- --- 11501051- --- 11511052- --- 11521053- 1153- --1054- 1154- --1055- 1155- --1056- 1156- --1057- 1157- --1058- 1158- --1059- 1159- --1060- 1160- ---10 +30 MIL-PRF-39018/1H 4 40 40 40 40 40 40 40 40 60 60 60 60 60 60 60 75 75 75 75 75 75 75 100 100 100 100 100 100 100 100 ESR DC surge voltage +85C +125C volts 50 50 50 50 50 50 50 50 75 75 75 75 75 75 75 100 100 100 100 100 100 100 150 150 150 150 150 150 150 150 Cap TABLE I. Styles CU12, CU13, and CUR13 capacitors - Continued. DC rated voltage Cap ESR DC surge voltage Max. Imped. at -55C and 120 Hz DC leakage Max. ac ripple current 120 Hz at 85C 1/ Case size Style CU12 Capacitance tolerance Dash number Style CU13 Capacitance tolerance Style CUR13 2/ Capacitance tolerance +125C +85C +125C +25C 5 MIL-PRF-39018/1H +85C +85C -10 -10 -10 -10 -10 -10 -10 -10 -10 +25 C and and +30 +50 +75 +30 +50 +75 +30 +50 +75 +125C +125C volts volts mA Percent Percent Percent F A --- 1061- 1161- --0690 0790 --0490 0590 A0 63 24 4 770 80.38 40.30 175 225 3.3 150 200 --- 1089- 1189- --0661 0761 --0461 0561 A0 68 24 4 500 68.02 34.01 175 225 3.9 150 200 --- 1062- 1162- --0662 0762 --0462 0562 A1 86 36 6 333 47.37 23.68 175 225 5.6 150 200 --- 1063- 1163- --0663 0763 --0463 0563 A2 113 36 6 250 32.35 16.17 175 225 8.2 150 200 --- 1064- 1164- --0664 0764 --0464 0564 A3 148 48 8 154 22.10 11.05 175 225 12 150 200 --- 1065- 1165- --0665 0765 --0465 0565 A4 177 60 10 118 17.68 8.84 175 225 15 150 200 --- 1066- 1166- --0666 0766 --0466 0566 A5 271 84 14 77 9.82 4.91 175 225 27 150 200 --- 1067- 1167- --0667 0767 --0467 0567 A6 353 120 20 51 6.80 3.40 175 225 39 150 200 --- 1068- 1168- --0691 0791 --0491 0591 A0 58 24 4 910 60.45 120.57 225 275 2.2 200 250 --- 1090- 1190- --0668 0768 --0468 0568 A0 70 24 4 910 80.38 40.19 225 275 3.3 200 250 --- 1069- 1169- --0669 0769 --0469 0569 A1 86 36 6 540 47.37 23.68 225 275 5.6 200 250 --- 1070- 1170- --0670 0770 --0470 0570 A2 103 36 6 440 39.01 19.50 225 275 6.8 200 250 --- 1071- 1171- --0671 0771 --0471 0571 A3 125 48 8 300 26.53 13.26 225 275 10 200 250 --- 1072- 1172- --0672 0772 --0472 0572 A4 159 60 10 250 22.10 11.05 225 275 12 200 250 --- 1073- 1173- --0673 0773 --0473 0573 A5 245 84 14 140 12.06 6.03 225 275 22 200 250 --- 1074- 1174- --0674 0774 --0474 0574 A6 294 120 20 110 9.82 4.91 225 275 27 200 250 --- 1075- 1175- --0692 0792 --0492 0592 A0 42 96 16 1300 132.66 221.05 250 1.5 325 225 300 --- 1091- 1191- --0675 0775 --0475 0575 A0 51 96 16 1300 90.43 150.71 250 2.2 325 225 300 --- 1076- 1176- --0693 0793 --0493 0593 A1 71 120 20 640 85.02 51.01 250 3.9 325 225 300 --- 1092- 1192- --0676 0776 --0476 0576 A1 78 120 20 640 70.55 42.33 250 4.7 325 225 300 --- 1077- 1177- --0689 0789 --0489 0589 A2 84 132 22 440 59.21 35.53 250 5.6 325 225 300 --- 1078- 1178- --0678 0778 --0478 0578 A3 110 144 24 370 40.44 24.26 250 8.2 325 225 300 --- 1079- 1179- --0679 0779 --0479 0579 A4 130 156 26 300 33.16 19.89 250 325 10 225 300 --- 1080- 1180- --0680 0780 --0480 0580 A5 185 180 30 200 20.72 12.43 250 325 16 225 300 --- 1081- 1181- --0681 0781 --0481 0581 A6 217 216 36 170 18.42 11.05 250 325 18 225 300 --- 1082- 1182- --0694 0794 --0494 0594 A0 35 120 20 2000 199.00 331.57 300 375 1.0 275 350 ----- 1083- 1183 0683 0783 --0483 0583 A1 59 156 26 910 60.29 100.42 300 375 3.3 275 350 --- 1084- 1184- --0684 0784 --0484 0584 A2 70 168 28 770 85.02 51.01 300 375 3.9 275 350 --- 1085- 1185- --0685 0785 --0485 0585 A3 90 192 32 540 59.21 35.53 300 375 5.6 275 350 --- 1086- 1186- --0686 0786 --0486 0586 A4 107 204 34 440 48.76 29.26 300 375 6.8 275 350 --- 1087- 1187- --0687 0787 --0487 0587 A5 148 228 38 300 33.16 19.89 300 375 10 275 350 --- 1088- 1188- --0688 0788 --0488 0588 A6 174 252 42 250 27.63 16.58 300 375 12 275 350 1/ The ripple current values shown are representative values not supported by test data. 2/ The last letter in dash number will indicate FR level symbol ("M", "P", "R", or "S"). For style CUR13 with random vibration, the letter "R" will be used in place of the dash between the spec sheet number and the dash number (i.e., M39018/01R1046M). 3/ Maximum current due to voltage limitations. +85C MIL-PRF-39018/1H Stability at reduced and high temperatures: Step 1 (at +25C): DCL: See table I. Cap.: See table I. ESR: See table I. Step 2 (at -55C): Impedance: See table I. Cap.: Within 30 percent of step 1 value. Step 3 (at +25C): DCL: See table I. Cap.: Within 5 percent of step 1 value. ESR: See table I. Step 4 (at +125C): DCL: See table I. Cap.: Within 25 percent of step 1 value. ESR: See table I. Step 5 (at +25C): DCL: See table I. Cap.: Within 5 percent of step 1 value. ESR: See table I. Life: Method 108 of MIL-STD-202. For qualification: Condition F (2,000 hours) at +85C. DCL: See table I. Cap.: Within 15 percent of initial measured value. ESR: Not more than 130 percent of initial requirement. 6 MIL-PRF-39018/1H For quality conformance: Performance check, condition B (250 hours) at +85C (non-ER). DCL: See table I. Cap.: Within 10 percent of initial measured value. ESR: See table I. For quality conformance: Continuation test (1,750 hours) at +85C (non-ER). DCL: See table I. Cap.: Within 15 percent of initial measured value. ESR: Not more than 130 percent of initial requirement. For quality conformance: 10,000 hours (ER) at +85C. DCL: At +25C initial limit, at +85C, 125 percent of initial limit. Cap.: Within 25 percent of initial measured value. ESR: Not more than 200 percent of initial requirement. Case insulation (CU13 and CUR13 only): In accordance with MIL-PRF-39018. Vibration: * High frequency: In accordance with MIL-PRF-39018. Random (style CUR13 only) (when applicable): In accordance with MIL-PRF-39018. Thermal shock and immersion: Thermal shock: Method 107 of MIL-STD-202, condition A, except in step 3, units shall be tested at applicable high temperature. Immersion: Method 104 of MIL-STD-202, condition B (2 cycles, 30 minutes). DCL: See table I. Cap.: Within 5 percent of initial measured value. ESR: See table I. Case insulation (CU13 and CUR13 only): Shall meet initial requirement. Surge voltage: DCL: See table I. Cap.: Within 6 percent of initial measured value. ESR: See table I. 7 MIL-PRF-39018/1H Moisture resistance: Method 106 of MIL-STD-202. DCL: See table I. Cap: Within 6 percent of initial measured value. ESR: See table I. Case Insulation (CU13 and CUR13 only): Shall meet initial requirement. High temperature exposure (500 hours at +125C): DCL: Not more than 200 percent of initial requirement for units less than 150 volts and 300 percent for units 150 volts and greater. Cap.: Within 10 percent of initial measured value. ESR: Not more than 115 percent of initial requirement. Reverse voltage: After 125 hours at 125C with 1 +0 -.1 reverse volt applied to units rated at 7 V dc, and 3 +0 -.3 reverse volts applied to all others. After additional 125 hours at 125C with rated forward voltage applied: DCL: Within 125 percent of initial requirement. Cap.: Within the following percentages of the initial measured value: 7 to 30 V dc inclusive: +10, -25 percent. 50 to 350 V dc inclusive: 10 percent. ESR: See table I. Penetration of solvents: In accordance with MIL-PRF-39018. High temperature verification: In accordance with MIL-PRF-39018 at +125C with derated voltage applied: DCL: See table I. Cap: Within 10 percent of initial measured value. ESR: Not more than 130 percent of initial requirement. Reverse voltage aging: In accordance with MIL-PRF-39018. Marking: In accordance with MIL-PRF-39018. Part or Identifying Number (PIN): M39018/01- (Dash number from table I). For style CUR13, parts with random vibration, the letter R shall be used in place of the dash (i.e., M39018/01R1046M). Substitutability data: See table II. 8 MIL-PRF-39018/1H TABLE II. Substitutability data. Dash number in MIL-PRF-39018/1A, /1B, /1C, /1D, /1E 1/ Style CU12 Style CU13 Capacitance tolerance -10 +30 -10 +50 -10 +75 0401 --0501 0402 --0502 0403 --0503 0404 --0504 0405 --0505 0406 --0506 ------0407 --0507 0408 --0508 0409 --0509 0410 --0510 0411 --0511 0412 --0512 0413 --0513 0414 --0514 0415 --0515 0416 --0516 0417 --0517 0418 --0518 0419 --0519 0420 --0520 0421 --0521 0422 --0522 0423 --0523 0424 --0524 0425 --0525 0426 --0526 0427 --0527 0428 --0528 0429 --0529 0430 --0530 0431 --0531 0432 --0532 0433 --0533 0434 --0534 0435 --0535 0436 --0536 0437 --0537 0438 --0538 0439 --0539 0440 --0540 0441 --0541 0442 --0542 0443 --0543 0444 --0544 0445 --0545 0446 0546 --0447 0547 --0448 0548 --0449 0549 --0450 0550 --0451 0551 --- Dash number MIL-PRF-39018/1 Style CU12 Style CU13 Capacitance tolerance -10 +30 -10 +50 -10 +75 0601 --0701 0602 --0702 0603 --0703 0604 --0704 0605 --0705 0606 --0706 ------0607 --0707 0608 --0708 0609 --0709 0610 --0710 0611 --0711 0612 --0712 0613 --0713 0614 --0714 0615 --0715 0616 --0716 0617 --0717 0618 --0718 0619 --0719 0620 --0720 0621 --0721 0622 --0722 0623 --0723 0624 --0724 0625 --0725 0626 --0726 0627 --0727 0628 --0728 0629 --0729 0630 --0730 0631 --0731 0632 --0732 0633 --0733 0634 --0734 0635 --0735 0636 --0736 0637 --0737 0638 --0738 0639 --0739 0640 --0740 0641 --0741 0642 --0742 0643 --0743 0644 --0744 0645 --0745 0646 0746 --0647 0747 --0648 0748 --0649 0749 --0650 0750 --0651 0751 --- Capacitance tolerance -10 +30 -10 +50 -10 +75 0005 --0006 0009 --0010 0013 --0014 0017 --0018 0021 --0022 0025 --0026 0001 --0002 0029 --0030 0033 --0034 0037 --0038 0041 --0042 0045 --0046 0049 --0050 0053 --0054 0057 --0058 0061 --0062 0065 --0066 0069 --0070 0073 --0074 0077 --0078 0081 --0082 0085 --0086 0089 --0090 0093 --0094 0097 --0098 0101 --0102 0105 --0106 0109 --0110 0113 --0114 0117 --0118 0121 --0122 0125 --0126 0129 --0130 0133 --0134 0137 --0138 0141 --0142 0145 --0146 0149 --0150 0153 --0154 0157 --0158 0161 --0162 0165 --0166 0169 --0170 0173 --0174 0177 --0178 0181 --0182 0185 0186 --0189 0190 --0193 0194 --0197 0198 --0201 0202 --0205 0206 --- See footnotes at end of table. 9 Capacitance tolerance -10 +30 -10 +50 -10 +75 0007 --0008 0011 --0012 0015 --0016 0019 --0020 0023 --0024 0027 --0028 0003 --0004 0031 --0032 0035 --0036 0039 --0040 0043 --0044 0047 --0048 0051 --0052 0055 --0056 0059 --0060 0063 --0064 0067 --0068 0071 --0072 0075 --0076 0079 --0080 0083 --0084 0087 --0088 0091 --0092 0095 --0096 0099 --0100 0103 --0104 0107 --0108 0111 --0112 0115 --0116 0119 --0120 0123 --0124 0127 --0128 0131 --0132 0135 --0136 0139 --0140 0143 --0144 0147 --0148 0151 --0152 0155 --0156 0159 --0160 0163 --0164 0167 --0168 0171 --0172 0175 --0176 0179 --0180 0183 --0184 0187 0188 --0191 0192 --0195 0196 --0199 0200 --0203 0204 --0207 0208 --- MIL-PRF-39018/1H TABLE II. Substitutability data - Continued. Dash number in MIL-PRF-39018/1A, /1B, /1C, /1D, /1E 1/ Style CU12 Style CU13 Capacitance tolerance -10 +30 -10 +50 -10 +75 0452 0552 --0453 0553 --0454 0554 --0455 0555 --0456 0556 --0457 0557 --0458 0558 --0459 0559 --0460 0560 --0461 0561 --0462 0562 --0463 0563 --0464 0564 --0465 0565 --0466 0566 --0467 0567 --0468 0568 --0469 0569 --0470 0570 --0471 0571 --0472 0572 --0473 0573 --0474 0574 --- Dash number MIL-PRF-39018/1 Style CU12 Style CU13 Capacitance tolerance -10 +30 -10 +50 -10 +75 0652 0752 --0653 0753 --0654 0754 --0655 0755 --0656 0756 --0657 0757 --0658 0758 --0659 0759 --0660 0760 --0661 0761 --0662 0762 --0663 0763 --0664 0764 --0665 0765 --0666 0766 --0667 0767 --0668 0768 --0669 0769 --0670 0770 --0671 0771 --0672 0772 --0673 0773 --0674 0774 --- Capacitance tolerance -10 +30 -10 +50 -10 +75 0209 0210 --0213 0214 --0217 0218 --0221 0222 --0225 0226 --0229 0230 --0233 0234 --0237 0238 --0241 0242 --------------------------------------0245 0246 --0249 0250 --0253 0254 --0257 0258 --0261 0262 --0265 0266 --0269 0270 --0273 0274 --- Capacitance tolerance -10 +30 -10 +50 -10 +75 0211 0212 --0215 0216 --0219 0220 --0223 0224 --0227 0228 --0231 0232 --0235 0236 --0239 0240 --0243 0244 --------------------------------------0247 0248 --0251 0252 --0255 0256 --0259 0260 --0263 0264 --0267 0268 --0271 0272 --0275 0276 --- 1/ The following dash numbers have been canceled with no replacement items recommended: 0477 0482 0577 0582 0677 0682 0777 0782 APPLICATION NOTE: Ripple current: The maximum permissible ripple current for these capacitors can be determined from table III. The appropriate multiplier from this table should be used where operation at other frequencies or temperatures is desired. Operation of these capacitors outside the limits of 60 to 100,000 Hz is not recommended. TABLE III. Ripple current multipliers. With temperature With frequency +25C 1.4 +45C 1.4 60 Hz +65C 1.2 120 Hz +85C 1.0 400 Hz +125C 0.3 1 K through 0- 60 volts 61-200 201-350 .85 .83 .80 1.0 1.0 1.0 1.1 1.15 1.3 1.15 1.2 1.4 10 MIL-PRF-39018/1H NOTES: Reference document. MIL-PRF-39018. MIL-STD-202. Changes from previous issue. The margins of this specification are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Army - CR Navy - EC Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5910-2009-020) Review activities: Navy - AS, MC, OS, SH Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil/. 11