PRODUCT DESCRIPTION
IPA Presaturated Wipes remove solder paste,
inks and other contaminants. These highly
effective cleaning wipes are ideal for all
general cleaning applications. IPA
Presaturated Wipes are well suited for touch-
up cleaning of automatic printer stencils and
cleaning of semi-automatic printer stencils
during and at the end of production runs.
IPA Presaturated Wipes contain ultra-pure
Electronics Grade IPA. The wipes are
available in a C-fold wipe contained in a
convenient dispensing box or in a tub.
Plastic Safe
Lint free
RoHS Compliant
Flammable
Regular Cleaning Strength
California - CARB Electronics Cleaner
75% Compliant
TYPICAL APPLICATIONS
IPA Presaturated Wipes are engineered for
cleaning:
Screens & Stenc ils
Fiber Optics & Connectors
Cables
Hard-line Coax Cable
Metal & Fiber Optic Cable Splices
PC Boards
Control Systems
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point
174° F Initial
Evaporation Rate (butyl acetate=1) <1
Flash Point (TCC) 68º F
Specific Gravity 0.88
Vapor Pressure @68°F 198 mm Hg
Odor
Mild Alcohol
Solubilit y in Water Soluble
Kauri-Butanol (KB) Numb er 56
VOC* Content:
CARB 70 %
SCAQMD 616 g/L
Federal 70 %
RoHS Compliant
Shelflife 2 yea rs
*Volatile Organic Compound (VOC) information is calculated on a
weight basis using the VOC definition of California Air Resources
Board (CARB) Consumer Product Regulations, South Coast Air
Quality Management District ( SCAQMD) Rule 102 and the Federal
definition published in 40 CFR 51.100(s).
COMPATIBILITY
IPA Presaturated Wipes are generally
compatible with most materials. As with any
chemical product, component compatibility
must be determined on a non-critical area
prior to use.
CHEMTRONICS
Technical Data Sheet
IPA
Presaturated Wipes
TDS# SIP100P
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
SIP100P tub directions:
Remove top of container and peel foil seal
from top of tub. Pull the first wipe from
center of roll and feed it through the opening
in the lid. Replace lid and pull first w ipe from
the tub and separate at perforation. Keep
container closed to prevent wipes from
drying out.
IPA100B box directions:
Open box and remove wipes from pouch
found inside box. Pull wipes as needed from
the box and close box between uses to
prevent wipes from drying out.
Cleaning directions:
General cleaning: Wipe surfaces thoroughly
to remove contaminants. When removing
heavy soils, use a clean wipe for final wipe
down.
Stencil cleaning: Wipe away residual solder
paste until surface is thoroughly cleaned.
Repeat with a clean wipe to remove any trace
contaminants.
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics provides a technical hotline to
answer your technical and application related
questions. The toll free number is: 1-800-
TECH-401.
AVAILABILITY
SIP100P Presaturated Wipes (100/tub)
IPA100B C-Fold Wipes (100/box)
ENVIRONMENTAL IMPACT DATA
HCFC-141b
HCFC-225
HFC
nPB
None
None
Hydrochlorofluorocarbons (HCFCs) are regulated
under the Montreal Protocol as Class II ozone
depleting substances. HCFC-141b is no longer
produced in the US under this legislation. HCFC-225
is planned for production phase-out in 2015.
Hydrofluorocarbons (HFCs) are not currently
regulated.
EPA has listed n-propyl bromide (nPB) as an
acceptable alternative to ozone depleting substances
in metal, precision, and electronics cleaning under
Section 612 of the Clean Air Act.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS does not guarantee the accuracy of
the data and assumes no liability in connection with
damages incurred while using it.
Chemtronics is a registered trademark of Chemtronics. All
rights reser ved.
CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. G (08/13)
DISTRIBUTED BY: