19-1335; Rev 0a; 2/98 KIT ATION EVALU E L B AVAILA Low-Power, 90Msps, 6-Bit ADC Features High Sampling Rate: 90Msps The MAX1011's input amplifier features a true differential input, a -0.5dB analog bandwidth of 55MHz, and a userprogrammable input full-scale range of 125mVp-p, 250mVp-p, or 500mVp-p. With an AC-coupled signal, input offset is typically less than 1/4LSB. Dynamic performance is 5.85 effective number of bits (ENOB) with a 20MHz analog input signal, or 5.7 ENOB with a 50MHz signal. Internal Bandgap Voltage Reference The MAX1011 operates with +5V analog and +3.3V digital supplies for easy interfacing to +3.3V-logic-compatible digital signal processors and microprocessors. It comes in a 24-pin QSOP package. Single-Ended or Differential Input Drive Low Power Dissipation: 215mW Excellent Dynamic Performance: 5.85 ENOB with 20MHz Analog Input 5.7 ENOB with 50MHz Analog Input 1/4LSB INL and DNL (typ) 1/4LSB Input Offset (typ) Internal Oscillator with Overdrive Capability 55MHz (-0.5dB) Bandwidth Input Amplifier with True Differential Input User-Selectable Full-Scale Range (125mVp-p, 250mVp-p, or 500mVp-p) Flexible, 3.3V, CMOS-Compatible Digital Outputs Applications IF Sampling Receivers VSAT Receivers Wide Local Area Networks (WLANs) Instrumentation Ordering Information PART TEMP. RANGE MAX1011CEG 0C to +70C PIN-PACKAGE 24 QSOP Pin Configuration appears at end of data sheet. Functional Diagram OCC+ OCC- IN+ IN- ADC INPUT AMP 6 DATA BUFFER VREF OFFSET CORRECTION GAIN 6 CLOCK OUT BANDGAP REFERENCE CLOCK DRIVER D0-D5 DCLK TNK+ TNK- MAX1011 ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800 For small orders, phone 408-737-7600 ext. 3468. MAX1011 General Description The MAX1011 is a 6-bit analog-to-digital converter (ADC) that combines high-speed, low-power operation with a user-selectable input range, an internal reference, and a clock oscillator. The ADC converts analog signals into binary-coded digital outputs at sampling rates up to 90Msps. The ability to directly interface with baseband signals makes the MAX1011 ideal for use in a wide range of communications and instrumentation applications. MAX1011 Low-Power, 90Msps, 6-Bit ADC ABSOLUTE MAXIMUM RATINGS VCC to GND ..........................................................-0.3V to +6.5V VCCO to OGND......................................................-0.3V to +6.5V GND to OGND ......................................................-0.3V to +0.3V Digital and Clock Output Pins to OGND...-0.3V to VCCO (10sec) All Other Pins to GND...............................................-0.3V to VCC Continuous Power Dissipation (TA = +70C) 24-Pin QSOP (derate 10mW/C above +70C)...........800mW Operating Temperature Range...............................0C to +70C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, <10sec)...........................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (VCC = +5V 5%, VCCO = 3.3V 300mV, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY (Note 1) Resolution RES 6 Integral Nonlinearity INL Differential Nonlinearity DNL No missing codes over temperature VFSH Full-Scale Input Range Bits -0.5 0.25 0.5 LSB -0.5 0.25 0.5 LSB GAIN = VCC (high gain) 118.75 125 131.25 VFSM GAIN = open (mid gain) 237.5 250 262.5 VFSL GAIN = GND (low gain) 475 500 525 mVp-p INVERTING AND NONINVERTING ANALOG INPUTS Input Open-Circuit Voltage VAOC 2.25 2.35 2.45 V Input Resistance RIN 13 20 29 k Input Capacitance CIN Guaranteed by design 1.5 3 pF Common-Mode Voltage Range VCM Other analog input driven with external source (Note 2) 1.75 2.75 V ROSC Other oscillator input tied to VCC + 0.3V 4.8 12.1 k Digital Outputs Logic-High Voltage VOH ISOURCE = 50A Digital Outputs Logic-Low Voltage VOL ISINK = 400A OSCILLATOR INPUTS Oscillator Input Resistance 8 DIGITAL OUTPUTS (D0-D5) 0.7VCCO V 0.5 V POWER SUPPLY Supply Current Power-Supply Rejection Ratio Digital Outputs Supply Current Power Dissipation 2 37 63.5 mA PSRR ICC VCC = 4.75V to 5.25V (Note 3) -65 -40 dB ICCO 20MHz, full-scale analog inputs, CL = 15pF (Note 4) 8.5 13.8 mA PD 215 _______________________________________________________________________________________ mW Low-Power, 90Msps, 6-Bit ADC (VCC = +5V 5%, VCCO = 3.3V 300mV, TA = +25C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DYNAMIC PERFORMANCE (Gain = open, external 90MHz clock (Figure 7), VIN = 20MHz sine, amplitude -1dB below full scale, unless otherwise noted.) Maximum Sample Rate fMAX Analog Input -0.5dB Bandwidth BW 90 GAIN = GND, open, VCC GAIN = open (mid gain) Input Offset (Note 5) 5.6 GAIN = open (mid gain), fIN = 50MHz, -1dB below full scale 5.7 ENOBH ENOBL GAIN = VCC (high gain) GAIN = GND (low gain) 5.8 5.85 SINAD GAIN = open (mid gain) 35.5 Guaranteed by design -0.5 OFF MHz 5.85 ENOBM Effective Number of Bits Signal-to-Noise Plus Distortion Ratio Msps 55 Bits 37 dB 0.5 LSB TIMING CHARACTERISTICS (Data outputs: RL = 1M, CL = 15pF) Clock to Data Propagation Delay tPD (Note 6) Data Valid Skew tSKEW (Note 6) Input to DCLK Delay tDCLK TNK+ to DCLK (Note 6) Figure 8 5.5 ns 1 clock cycle Aperture Delay Pipeline Delay tAD PD Figure 8 3.0 ns 1 ns 4.5 ns Note 1: Best-fit straight-line linearity method. Note 2: A typical application will AC couple the analog input to the DC bias level present at the analog inputs (typically 2.35V). However, it is also possible to DC couple the analog input (using differential or single-ended drive) within this commonmode input range (Figures 4 and 5). Note 3: PSRR is defined as the change in the mid-gain, full-scale range as a function of the variation in V CC supply voltage, expressed in decibels. Note 4: The current in the VCCO supply is a strong function of the capacitive loading on the digital outputs. To minimize supply transients and achieve optimal dynamic performance, reduce the capacitive-loading effects by keeping line lengths on the digital outputs to a minimum. Note 5: Offset-correction compensation enabled, 0.22F at compensation inputs (Figures 2 and 3). Note 6: tPD and tSKEW are measured from the 1.4V level of the output clock, to the 1.4V level of either the rising or falling edge of a data bit. tDCLK is measured from the 50% level of the clock-overdrive signal on TNK+ to the 1.4V level of DCLK. The capacitive load on the outputs is 15pF. _______________________________________________________________________________________ 3 MAX1011 AC ELECTRICAL CHARACTERISTICS __________________________________________Typical Operating Characteristics (VCC = +5V 5%, VCCO = 3.3V 300mV, fCLK = 90Msps, GAIN = open (midgain) MAX1011 evaluation kit, TA = +25C, unless otherwise noted.) EFFECTIVE NUMBER OF BITS vs. ANALOG INPUT FREQUENCY EFFECTIVE NUMBER OF BITS vs. SAMPLING/CLOCK FREQUENCY ANALOG INPUT BANDWIDTH EFFECTIVE NUMBER OF BITS MAGNITUDE (dB) -0.2 5.4 5.2 -0.4 -0.6 MAX1011-03 0 5.8 5.6 6.0 MAX1011-02 MAX1011-01 6.0 5.9 5.8 5.7 -0.8 5.6 -1.0 5.5 fCLK = 90Msps fIN = 20MHz 5.0 100 10 1 ANALOG INPUT FREQUENCY (MHz) 10 1 100 OSCILLATOR OPEN-LOOP PHASE NOISE vs. FREQUENCY OFFSET 100 FFT PLOT 0 MAX1011-04 -50 -70 fIN = 19.9512MHz fCLK = 90.000MHz 1024 POINTS AC-COUPLED SINGLE-ENDED AVERAGED -20 AMPLITUDE (dB) PHASE NOISE (dBc) 10 CLOCK FREQUENCY (MHz) ANALOG INPUT FREQUENCY (MHz) -90 -110 MAX1011-05 EFFECTIVE NUMBER OF BITS -40 -60 -130 -80 10k 1k 100k 1M 0 18 27 36 FREQUENCY (MHz) INTEGRAL NONLINEARITY vs. CODE DIFFERENTIAL NONLINEARITY vs. CODE 45 MAX1003-07 MAX1011-06 0.50 0.25 DNL (LSB) 0.25 0 0 -0.25 -0.25 -0.50 -0.50 0 10 20 30 CODE 4 9 FREQUENCY OFFSET FROM CARRIER (Hz) 0.50 INL (LSB) MAX1011 Low-Power, 90Msps, 6-Bit ADC 40 50 60 64 0 10 20 30 40 CODE _______________________________________________________________________________________ 50 60 64 Low-Power, 90Msps, 6-Bit ADC PIN NAME 1 GAIN FUNCTION 2 OCC+ Positive Offset-Correction Compensation. Connect a 0.22F capacitor for AC-coupled inputs. Ground pin 2 for DC-coupled inputs. 3 OCC- Negative Offset-Correction Compensation. Connect a 0.22F capacitor for AC-coupled inputs. Ground pin 3 for DC-coupled inputs. 4 IN+ Noninverting Analog Input 5 IN- Inverting Analog Input 6 VCC +5V 5% Supply. Bypass with a 0.01F capacitor to GND (pin 9). 7 TNK+ Positive Oscillator/Clock Input 8 TNK- Negative Oscillator/Clock Input 9, 10, 12, 13 GND Analog Ground 11 VCC +5V 5% Supply. Bypass with a 0.01F capacitor to GND (pin 10). 14 VCC +5V 5% Supply. Bypass with a 0.01F capacitor to GND (pin 13). 15 N.C. No Connection 16 OGND Digital Output Ground 17 VCCO Digital Output Supply, +3.3V 300mV. Bypass with a 47pF capacitor to OGND (pin 16). 18 DCLK Digital Clock Output. Frames the output data. 19-24 D0-D5 Digital Outputs 0-5. D5 is the most significant bit (MSB). Gain-Select Input. Sets input full-scale range: 125/250/500mVp-p (Table 1). _______________Detailed Description Converter Operation The MAX1011 integrates a 6-bit analog-to-digital converter (ADC), a buffered voltage reference, and oscillator circuitry. The ADC uses a flash conversion technique to convert an analog input signal into a 6-bit parallel digital output code. The MAX1011's unique design includes 63 fully differential comparators and a proprietary encoding scheme that ensures no more than 1LSB dynamic encoding error. The control logic interfaces easily to most digital signal processors (DSPs) and microprocessors (Ps) with +3.3V CMOS-compatible logic interfaces. Figure 1 shows the MAX1011 in a typical application. Programmable Input Amplifier The MAX1011 has a programmable-gain input amplifier with a -0.5dB bandwidth of 55MHz and a true differential input. To maximize performance in high-speed systems, the amplifier has less than 3pF of input capacitance. The input amplifier gain is programmed via the GAIN pin to provide three possible input fullscale ranges (FSRs) as shown in Table 1. Single-ended and differential AC-coupled input circuit examples are shown in Figures 2 and 3. Each of the Table 1. Input Amplifier Programming GAIN INPUT FULL-SCALE RANGE (mVp-p) GND 500 Open 250 VCC 125 _______________________________________________________________________________________ 5 MAX1011 Pin Description MAX1011 Low-Power, 90Msps, 6-Bit ADC amplifier inputs is internally biased to a 2.35V reference through a 20k resistor, eliminating external DC bias circuits. A series 0.1F capacitor is required at the amplifier input for AC-coupled signals. When operating with AC-coupled inputs, the input amplifier's DC offset voltage is nulled to within 1/2LSB by an on-chip, offset-correction amplifier. An external compensation capacitor is required to set the dominant pole of the offset-correction amplifier's frequency response (Figures 2 and 3). The compensation capacitor will determine the low-frequency corner of the analog input response according to the following formula: fc = 1 / (0.1 x C) where C is the value of the compensation capacitor in F, and fc is the corner frequency in Hz. MAX1011 RF 6 BITS 6 DATA BUFFER DIGITAL DEMODULATOR OR DSP DCLK LO TANK Figure 1. IF Sampling Receiver 0.22F 0.22F OCC+ OCC+ OCC- OFFSET CORRECTION OFFSET CORRECTION 0.1F 0.1F IN+ INPUT AMP VSOURCE IN+ INPUT AMP VSOURCE IN- IN0.1F 0.1F 20k MAX1011 20k 2.35V INTERNAL REFERENCE Figure 2. Single-Ended AC-Coupled Input 6 OCC- 20k MAX1011 20k 2.35V INTERNAL REFERENCE Figure 3. Differential AC-Coupled Input _______________________________________________________________________________________ Low-Power, 90Msps, 6-Bit ADC ADC The ADC block receives the analog signal from the input amplifier. The ADC uses flash conversion with 63 fully differential comparators to digitize the analog input signal into a 6-bit output in offset binary format. The MAX1011 features a proprietary encoding scheme that ensures no more than 1LSB dynamic encoding error. Dynamic encoding errors resulting from metastable states may occur when the analog input voltage, at the time the sample is taken, falls close to the decision point for any one of the input comparators. The resulting output code for typical converters can be incorrect, including false full- or zero-scale outputs. The MAX1011's unique design reduces the magnitude of this type of error to 1LSB. Internal Voltage Reference An internal buffered-bandgap reference is included on the MAX1011 to drive the ADC's reference ladder. The on-chip reference and buffer eliminate any external (high-impedance) connections to the reference ladder, minimizing the potential for noise coupling from external circuitry while ensuring that the voltage reference, input amplifier, and reference ladder track well with variations of temperature and power supplies. Oscillator Circuit The MAX1011 includes a differential oscillator, which is controlled by an external parallel resonant (tank) network as shown in Figure 6. Alternatively, the oscillator may be overdriven with an external clock source as shown in Figure 7. Internal Clock Operation (Tank) If the tank circuit is used, the resonant inductor should have a sufficiently high Q and a self-resonant frequency (SRF) of at least twice the intended oscillator frequency. Coilcraft's 1008HS-221, with an SRF of 700MHz and a Q of 45, works well for this application. Generate different clock frequency ranges by adjusting varactor and tank elements. An internal clock-driver buffer is included to provide sharp clock edges to the internal flash comparators. The buffer ensures that the comparators are simultaneously clocked, maximizing the ADC's effective number of bits (ENOB) performance. OFFSET CORRECTION DISABLED OCC+ OFFSET CORRECTION DISABLED OCC- OCC+ OFFSET CORRECTION OFFSET CORRECTION IN+ IN+ INPUT AMP VSOURCE VCM 1.75V TO 2.75V INPUT AMP VSOURCE IN20k OCC- IN- MAX1011 20k 2.35V INTERNAL REFERENCE Figure 4. Single-Ended DC-Coupled Input 20k DIFFERENTIAL SOURCE WITH COMMON MODE FROM 1.75V TO 2.75V. MAX1011 20k 2.35V INTERNAL REFERENCE Figure 5. Differential DC-Coupled Input _______________________________________________________________________________________ 7 MAX1011 For applications where a DC component of the input signal is present, Figures 4 and 5 show single-ended and differential DC-coupled input circuits. The amplifier's input common-mode voltage range extends from 1.75V to 2.75V. To prevent attenuation of the input signal's DC component in this mode, disable the offsetcorrection amplifier by grounding the OCC+ and OCCpins (Figures 4 and 5). MAX1011 Low-Power, 90Msps, 6-Bit ADC VCLK = 300mVp-p TO 1.25Vp-p 47k 0.1F 50 TNK+ 47pF 10k 5pF VTUNE Z0 = 50 TNK+ CLK DRIVER 220nH VCLK 50 CLK DRIVER TNK- TNK0.1F 47pF MAX1011 47k MAX1011 50 VTUNE = 0V TO 8V fOSC = 70MHz TO 109MHz VARACTOR DIODE PAIR IS M/A-COM MA4ST079CK-287 (SOT23 PACKAGE) INDUCTOR COILCRAFT 1008HS-221. Figure 6. Tank Resonator Oscillator Figure 7. External Clock Drive Circuit External Clock Operation To accommodate designs that use an external clock, the MAX1011's internal oscillator can be overdriven by an external clock source (Figure 7). The external clock source should be a sinusoid to minimize clock phase noise and jitter, which can degrade the ADC's ENOB performance. AC couple the clock source (recommended voltage level is approximately 1Vp-p) to the oscillator inputs (Figure 7). improved conversion accuracy. Use of separate ground planes is strongly recommended. The entire board needs good DC bypassing for both analog and digital supplies. Place the power-supply bypass capacitors close to where the power is routed onto the board, i.e., close to the connector. 10F electrolytic capacitors with low-ESR ratings are recommended. For best effective bits performance, minimize capacitive loading at the digital outputs. Keep the digital output traces as short as possible. The MAX1011 requires a +5V 5% power supply for the analog supply (VCC) and a +3.3V 300mV power supply connected to V CCO for the logic outputs. Bypass each of the VCC supply pins to its respective GND with high-quality ceramic capacitors located as close to the package as possible (Table 2). Consult the evaluation kit manual for a suggested layout and bypassing scheme. Output Data Format The conversion results are output on a 6-bit-wide data bus. Data is latched into the ADC output latch following a pipeline delay of one clock cycle (Figure 8). Output data is clocked out of the ADC's data output pins (D0 through D5) on the rising edge of the clock output (DCLK), with a DCLK-to-data propagation delay (tPD) of 3.0ns. The MAX1011 outputs are +3.3V CMOS-logic compatible. Transfer Function Figure 9 shows the MAX1011's nominal transfer function. Output coding is offset binary with 1LSB = FSR / 63. ___________Applications Information The MAX1011 is designed with separate analog and digital power-supply and ground connections to isolate high-current digital noise spikes from the more sensitive analog circuitry. The high-current digital output ground (OGND) and analog ground (GND) should be at the same DC level, connected at only one location on the board. This will provide best noise immunity and 8 Table 2. Bypassing Guide VCC/ VCCO (PIN) BYPASS TO GND/ OGND (PIN) CAPACITOR VALUE Analog Inputs 11 10 0.01F Oscillator/Clock 6 9 0.01F Converter 14 13 0.01F Digital Output 17 16 47pF SUPPLY FUNCTION _______________________________________________________________________________________ Low-Power, 90Msps, 6-Bit ADC MAX1011 N N+1 ANALOG INPUT N+2 tAD 50% TNK+ (INPUT CLOCK) tDCLK 1.4V tPD DCLK tSKEW 1.4V DATA OUT DATA VALID N - 1 DATA VALID N Figure 8. MAX1011 Timing Diagram ______________Dynamic Performance Signal-to-noise and distortion (SINAD) is the ratio of the fundamental input frequency's RMS amplitude to all other ADC output signals. The output spectrum is limited to frequencies above DC and below one-half the ADC sample rate. 111111 111110 The theoretical minimum analog-to-digital noise is caused by quantization error, and results directly from the ADC's resolution: SNR = (6.02N + 1.76)dB, where N is the number of bits of resolution. Therefore, a perfect 6-bit ADC can do no better than 38dB. The FFT Plot (see Typical Operating Characteristics) shows the result of sampling a pure 20MHz sinusoid at a 90MHz clock rate. This FFT plot of the output shows the output level in various spectral bands. The plot has been averaged to reduce the quantization noise floor and reveal the low-amplitude spurs. This emphasizes the excellent spurious-free dynamic range of the MAX1011. OUTPUT CODE 111101 100001 100000 011111 011110 000011 000010 000001 000000 -FSR 2 0 1LSB INPUT VOLTAGE (IN+ TO IN-) FSR 2 The effective resolution (or effective number of bits) the ADC provides can be measured by transposing the equation that converts resolution to SINAD: N = (SINAD - 1.76)/ 6.02 (see Typical Operating Characteristics). Figure 9. Ideal Transfer Function _______________________________________________________________________________________ 9 Low-Power, 90Msps, 6-Bit ADC MAX1011 Pin Configuration Chip Information TRANSISTOR COUNT: 2823 SUBSTRATE CONNECTED TO GND TOP VIEW GAIN 1 24 D5 OCC+ 2 23 D4 OCC- 3 22 D3 IN+ 4 IN- 5 21 D2 MAX1011 20 D1 19 D0 VCC 6 TNK+ 7 18 DCLK TNK- 8 17 VCCO GND 9 16 OGND GND 10 15 N.C. VCC 11 14 VCC GND 12 13 GND QSOP 10 ______________________________________________________________________________________ Low-Power, 90Msps, 6-Bit ADC QSOP.EPS ______________________________________________________________________________________ 11 MAX1011 Package Information MAX1011 Low-Power, 90Msps, 6-Bit ADC NOTES 12 ______________________________________________________________________________________