[ /Title (CD74 HC139 , CD74 HCT13 9) /Subject (High Speed CMOS Logic Dual 2-to-4 Line Decod CD54/74HC139, CD54/74HCT139 Data sheet acquired from Harris Semiconductor SCHS148B High-Speed CMOS Logic Dual 2-to-4 Line Decoder/Demultiplexer September 1997 - Revised May 2000 Features 1A1 or 2A0 and 2A1) cause one of the four normally high outputs to go low. * Multifunction Capability - Binary to 1 of 4 Decoders or 1 to 4 Line Demultiplexer If the enable input is high all four outputs remain high. For demultiplexer operation the enable input is the data input. The enable input also functions as a chip select when these devices are cascaded. This device is functionally the same as the CD4556B and is pin compatible with it. * Active Low Mutually Exclusive Outputs * Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads The outputs of these devices can drive 10 low power Schottky TTL equivalent loads. The HCT logic family is functionally as well as pin equivalent to the LS logic family. * Wide Operating Temperature Range . . . -55oC to 125oC Ordering Information * Balanced Propagation Delay and Transition Times * Significant Power Reduction Compared to LSTTL Logic ICs TEMP. RANGE (oC) PACKAGE CD54HC139F -55 to 125 16 Ld CERDIP CD54HC139F3A -55 to 125 16 Ld CERDIP CD74HC139E -55 to 125 16 Ld PDIP CD74HC139M -55 to 125 16 Ld SOIC CD54HCT139F -55 to 125 16 Ld CERDIP CD54HCT139F3A -55 to 125 16 Ld CERDIP CD74HCT139E -55 to 125 16 Ld PDIP CD74HCT139M -55 to 125 16 Ld SOIC PART NUMBER * HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30%of VCC at VCC = 5V * HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il 1A at VOL, VOH * Memory Decoding, Data Routing, Code Conversion Description NOTES: The 'HC139 and 'HCT139 devices contain two independent binary to one of four decoders each with a single active low enable input (1E or 2E). Data on the select inputs (1A0 and 1. When ordering, use the entire part number. Add the suffix 96 to obtain the variant in the tape and reel. 2. Die is available which meets all electrical specifications. Please contact your local TI sales office or customer service for ordering information. Pinout CD54HC139, CD54HCT139 (CERDIP) CD74HC139, CD74HCT139 (PDIP, SOIC) TOP VIEW 16 VCC 1E 1 1A0 2 15 2E 1A1 3 14 2A0 1Y0 4 13 2A1 1Y1 5 12 2Y0 1Y2 6 11 2Y1 1Y3 7 10 2Y2 GND 8 9 2Y3 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright (c) 2000, Texas Instruments Incorporated 1 CD54/74HC139, CD54/74HCT139 Functional Diagram 4 (12) 2 (14) Y0 5 (11) A0 Y1 6 (10) 3 (13) Y2 A1 7 (9) Y3 1 (15) E TRUTH TABLE INPUTS ENABLE SELECT OUTPUTS E A1 A0 Y3 Y2 Y1 Y0 0 0 0 1 1 1 0 0 0 1 1 1 0 1 0 1 0 1 0 1 1 0 1 1 0 1 1 1 1 X X 1 1 1 1 NOTE: X = Don't Care, Logic 1 = High, Logic 0 = Low Logic Diagram 4 (12) Y0 2 (14) A0 5 (11) Y1 3 (13) A1 6 (10) Y2 7 (9) Y3 1 (15) E 2 CD54/74HC139, CD54/74HCT139 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .25mA DC VCC or Ground Current, ICC or IGND . . . . . . . . . . . . . . . . . .50mA Thermal Resistance (Typical, Note 3) JA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 3. JA is measured with the component mounted on an evaluation PC board in free air. DC Electrical Specifications TEST CONDITIONS PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL VI (V) IO (mA) VCC (V) VIH - - 2 1.5 - - 1.5 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V MIN TYP MAX MIN MAX MIN MAX UNITS - 1.5 - V HC TYPES High Level Input Voltage Low Level Input Voltage High Level Output Voltage CMOS Loads VIL VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current - 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - 0.1 - 1 - 1 A ICC VCC or GND 0 6 - - 8 - 80 - 160 A 3 CD54/74HC139, CD54/74HCT139 DC Electrical Specifications (Continued) TEST CONDITIONS SYMBOL VI (V) IO (mA) High Level Input Voltage VIH - - Low Level Input Voltage VIL - High Level Output Voltage CMOS Loads VOH VIH or VIL PARAMETER 25oC VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 4.5 to 5.5 2 - - 2 - 2 - V - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V 0.1 - 1 - 1 A HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Per Input Pin: 1 Unit Load (Note 4) II VCC and GND 0 5.5 - ICC VCC or GND 0 5.5 - - 8 - 80 - 160 A ICC VCC -2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 A NOTE: 4. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS All 0.7 NOTE: Unit Load is ICC limit specified in DC Electrical Table, e.g., 360A max at 25oC. Switching Specifications Input tr, tf = 6ns PARAMETER -40oC TO 85oC 25oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPLH, tPHL CL = 50pF 2 - - 145 - 180 - 220 ns 4.5 - - 29 - 36 - 44 ns 6 - - 25 - 31 - 38 ns 2 - - 135 - 170 - 205 ns 4.5 - - 27 - 34 - 41 ns 6 - - 23 - 29 - 35 ns HC TYPES Propagation Delay A0, A1 to Outputs E to Outputs tPLH, tPHL CL = 50pF Select to Output tPLH, tPHL CL = 15pF 5 - 12 - - - - - ns Enable to Output tPLH, tPHL CL = 15pF 5 - 11 - - - - - ns 4 CD54/74HC139, CD54/74HCT139 Switching Specifications Input tr, tf = 6ns PARAMETER SYMBOL Output Transition Time (Figure 1) tTLH, tTHL (Continued) -40oC TO 85oC 25oC -55oC TO 125oC TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS CL = 50pF 2 - - 75 - 95 - 110 ns 4.5 - - 15 - 19 - 22 ns 6 - - 13 - 16 - 19 ns Power Dissipation Capacitance, (Notes 5, 6) CPD - 5 - 55 - - - - - pF Input Capacitance CIN - - - - 10 - 10 - 10 pF A0, A1 to Outputs tPLH, tPHL CL = 50pF 4.5 - - 34 - 43 - 51 ns E to Outputs tPLH, tPHL CL = 50pF 4.5 - - 34 - 43 - 51 ns Select to Output tPLH, tPHL CL = 15pF 5 - 14 - - - - - ns Enable to Output tPLH, tPHL CL = 15pF 5 - 14 - - - - - ns Output Transition Time (Figure 2) tTLH, tTHL CL = 50pF 4.5 - - 15 - 19 - 22 ns Power Dissipation Capacitance, (Notes 5, 6) CPD - 5 - 59 - - - - - pF Input Capacitance CIN - - - - 10 - 10 - 10 pF HCT TYPES Propagation Delay NOTES: 5. CPD is used to determine the dynamic power consumption, per decoder/demux. 6. PD = VCC2 fi (CPD + CL) where: fi = Input Frequency, CL = Output Load Capacitance, VCC = Supply Voltage. Test Circuits and Waveforms tr = 6ns tf = 6ns INPUT GND tTLH GND tTHL 90% 50% 10% INVERTING OUTPUT 3V 2.7V 1.3V 0.3V INPUT tTHL tPHL tf = 6ns tr = 6ns VCC 90% 50% 10% tTLH 90% 1.3V 10% INVERTING OUTPUT tPLH tPHL FIGURE 1. HC AND HCU TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tPLH FIGURE 2. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated