Low Noise, Low Drift, Low Power, 3-Axis MEMS Accelerometers ADXL354/ADXL355 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAMS V1P8ANA LDO VSUPPLY V1P8DIG RANGE POWER MANAGEMENT LDO XOUT ANALOG FILTER ST1 3-AXIS SENSOR OUT TEMP SENSOR TEMP CONTROL LOGIC ADXL354 VSSIO ST2 STBY VDDIO 14205-002 YOUT VSS Figure 1. ADXL354 Functional Block Diagram V1P8ANA LDO VSUPPLY V1P8DIG LDO VDDIO ADXL355 POWER MANAGEMENT ADC 3-AXIS SENSOR ANALOG FILTER ADC DIGITAL FILTER CONTROL LOGIC ADC TEMP SENSOR ADC FIFO VSSIO VSS SERIAL I/O INT1 INT2 DRDY CS/SCL SCLK/VSSIO MOSI/SDA MISO/ASEL 14205-001 Hermetic package offers excellent long-term stability 0 g offset vs. temperature (all axes): 0.15 mg/C maximum Ultralow noise density (all axes): 20 g/Hz (ADXL354) Low power, VSUPPLY (LDO enabled) ADXL354 in measurement mode: 150 A ADXL355 in measurement mode: 200 A ADXL354/ADXL355 in standby mode: 21 A ADXL354 has user adjustable analog output bandwidth ADXL355 digital output features Digital serial peripheral interface (SPI)/I2C interfaces 20-bit analog-to-digital converter (ADC) Data interpolation routine for synchronous sampling Programmable high- and low-pass digital filters Electromechanical self test Integrated temperature sensor Voltage range options VSUPPLY with internal regulators: 2.25 V to 3.6 V V1P8ANA, V1P8DIG with internal low dropout regulator (LDO) bypassed: 1.8 V typical 10% Operating temperature range: -40C to +125C 14-terminal, 6 mm x 6 mm x 2.1 mm, LCC package, 0.26 grams Figure 2. ADXL355 Functional Block Diagram APPLICATIONS Inertial measurement units (IMUs)/altitude and heading reference systems (AHRSs) Platform stabilization systems Structural health monitoring Seismic imaging Tilt sensing Robotics Condition monitoring GENERAL DESCRIPTION The analog output ADXL354 and the digital output ADXL355 are low noise density, low 0 g offset drift, low power, 3-axis accelerometers with selectable measurement ranges. The ADXL354B supports the 2 g and 4 g ranges, the ADXL354C supports the 2 g and 8 g ranges, and the ADXL355 supports the 2.048 g, 4.096 g, and 8.192 g ranges. The ADXL354/ ADXL355 offer industry leading noise, minimal offset drift over temperature, and long term stability enabling precision applications with minimal calibration. 1 Highly integrated in a compact form factor, the low power ADXL355 is ideal in an Internet of Things (IoT) sensor node and other wireless product designs. The ADXL355 multifunction pin names may be referenced by their relevant function only for either the SPI or I2C interfaces. Protected by U.S. Patents 8,472,270; 9,041,462; 8,665,627; 8,917,099; 6,892,576; 9,297,825; and 7,956,621. Rev. A Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2016-2018 Analog Devices, Inc. All rights reserved. www.analog.com Technical Support ADXL354/ADXL355 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 NVM_BUSY ............................................................................... 28 Applications ....................................................................................... 1 External Synchronization and Interpolation .......................... 29 Functional Block Diagrams ............................................................. 1 ADXL355 Register Map ................................................................. 31 General Description ......................................................................... 1 Register Definitions........................................................................ 32 Revision History ............................................................................... 2 Analog Devices ID Register ...................................................... 32 Specifications..................................................................................... 3 Analog Devices MEMS ID Register......................................... 32 Analog Output for the ADXL354 ............................................... 3 Device ID Register ..................................................................... 32 Digital Output for the ADXL355 ............................................... 4 Product Revision ID Register ................................................... 32 SPI Digital Interface Characteristics for the ADXL355 .......... 5 Status Register ............................................................................. 32 2 I C Digital Interface Characteristics for the ADXL355 ........... 6 FIFO Entries Register ................................................................ 33 Absolute Maximum Ratings............................................................ 8 Temperature Data Registers ...................................................... 33 Thermal Resistance ...................................................................... 8 X-Axis Data Registers ................................................................ 33 ESD Caution .................................................................................. 8 Y-Axis Data Registers ................................................................ 34 Pin Configurations and Function Descriptions ........................... 9 Z-Axis Data Registers ................................................................ 34 Typical Performance Characteristics ........................................... 11 FIFO Access Register ................................................................. 35 Root Allan Variance (RAV) ADXL355 Characteristics ......... 19 X-Axis Offset Trim Registers .................................................... 35 Theory of Operation ...................................................................... 20 Y-Axis Offset Trim Registers .................................................... 35 Analog Output ............................................................................ 20 Z-Axis Offset Trim Registers .................................................... 36 Digital Output ............................................................................. 21 Activity Enable Register ............................................................ 36 Axes of Acceleration Sensitivity ............................................... 21 Activity Threshold Registers ..................................................... 36 Power Sequencing ...................................................................... 22 Activity Count Register ............................................................. 36 Power Supply Description ......................................................... 22 Filter Settings Register ............................................................... 37 Overrange Protection................................................................. 22 FIFO Samples Register .............................................................. 37 Self Test ........................................................................................ 22 Interrupt Pin (INTx) Function Map Register......................... 37 Filter ............................................................................................. 23 Data Synchronization ................................................................ 38 Serial Communications ................................................................. 25 I2C Speed, Interrupt Polarity, and Range Register ................. 38 SPI Protocol ................................................................................. 25 Power Control Register ............................................................. 38 I2C Protocol ................................................................................. 26 Self Test Register ......................................................................... 39 Reading Acceleration or Temperature Data from the Interface ....................................................................................................... 26 Reset Register .............................................................................. 39 Recommended Soldering Profile ................................................. 40 FIFO ................................................................................................. 27 PCB Footprint Pattern ............................................................... 41 Interrupts ......................................................................................... 28 Packaging and Ordering Information ......................................... 42 DATA_RDY................................................................................. 28 Outline Dimensions ................................................................... 42 DRDY Pin .................................................................................... 28 Branding Information................................................................ 42 FIFO_FULL ................................................................................. 28 Ordering Guide .......................................................................... 42 FIFO_OVR .................................................................................. 28 Activity ......................................................................................... 28 REVISION HISTORY 4/2018--Rev. 0 to Rev. Added Vibration Parameter, Table 5 .............................................. 8 Changes to Overrange Protection Section .................................. 22 8/2016--Revision 0: Initial Version Rev. A | Page 2 of 42 Data Sheet ADXL354/ADXL355 SPECIFICATIONS ANALOG OUTPUT FOR THE ADXL354 TA = 25C, VSUPPLY = 3.3 V, x-axis acceleration and y-axis acceleration = 0 g, and z-axis acceleration = 1 g, unless otherwise noted. Table 1. Parameter SENSOR INPUT Output Full-Scale Range (FSR) Resonant Frequency1 Nonlinearity Cross Axis Sensitivity SENSITIVITY Sensitivity at XOUT, YOUT, ZOUT Sensitivity Change due to Temperature 0 g OFFSET 0 g Output for XOUT, YOUT, ZOUT 0 g Offset vs. Temperature (X-Axis, Y-Axis, and Z-Axis)2 Repeatability3 Vibration Rectification Error (VRE)4 NOISE DENSITY X-Axis, Y-Axis, and Z-Axis Velocity Random Walk BANDWIDTH Internal Low-Pass Filter Frequency SELF TEST Output Change X-Axis Y-Axis Z-Axis POWER SUPPLY Voltage Range VSUPPLY5 VDDIO V1P8ANA, V1P8DIG with Internal Low Dropout Regulator (LDO) Bypassed Current Measurement Mode VSUPPLY (LDO Enabled) V1P8ANA (LDO Disabled) V1P8DIG (LDO Disabled) Standby Mode VSUPPLY (LDO Enabled) V1P8ANA (LDO Disabled) V1P8DIG (LDO Disabled) Turn On Time6 Test Conditions/Comments Each axis ADXL354B, supports two ranges ADXL354C, supports two ranges Min Rev. A | Page 3 of 42 g g kHz % % 400 200 100 0.01 432 216 108 mV/g mV/g mV/g %/C -75 -0.15 25 0.1 3.5 9 <0.4 +75 +0.15 mg mg/C mg mg g Fixed frequency, 50% response attenuation 2 g range Power-off to standby Unit 368 184 92 X-axis and y-axis Z-axis VSUPPLY = 0 V Max 2/4 2/8 2.4 0.1 1 2 g Ratiometric to V1P8ANA 2 g 4 g 8 g -40C to +125C Each axis, 2 g Referred to V1P8ANA/2 -40C to +125C X-axis and y-axis Z-axis 2 g range, in a 1 g orientation, offset due to 2.5 g rms vibration 2 g Typ 2.25 V1P8DIG 1.62 20 9 13 g/Hz m/sec/Hr m/sec/Hr 1500 Hz 0.3 0.3 1.5 g g g 2.5 2.5 1.8 3.6 3.6 1.98 V V V 150 138 12 A A A 21 7 10 <10 <10 A A A ms ms ADXL354/ADXL355 Parameter OUTPUT AMPLIFIER Swing Output Series Resistance TEMPERATURE SENSOR Output at 25C Scale Factor TEMPERATURE Operating Temperature Range Data Sheet Test Conditions/Comments Min No load 0.03 Typ Max Unit V1P8ANA - 0.03 32 V k 892.2 3.0 mV mV/C -40 +125 C 1 The resonant frequency is a sensor characteristic. An integrated analog 1.5 kHz (-6 dB) sinc low-pass filter that cannot be bypassed limits the actual output response. The temperature change is -40C to +25C or +25C to +125C. 3 Repeatability is predicted for a 10 year life and includes shifts due to the high temperature operating life test (HTOL) (TA = 150C, VSUPPLY = 3.6 V, and 1000 hours), temperature cycling (-55C to +125C and 1000 cycles), velocity random walk, broadband noise, and temperature hysteresis. 4 The VRE measurement is the shift in dc offset while the device is subject to 2.5 g rms of random vibration from 50 Hz to 2 kHz. The device under test (DUT) is configured for the 2 g range and an output data rate of 4 kHz. The VRE scales with the range setting. 5 When V1P8ANA and V1P8DIG are generated internally, VSUPPLY is valid. To disable the LDO and drive V1P8ANA and V1P8DIG externally, connect VSUPPLY to VSS. 6 Standby to measurement mode; valid when the output is within 1 mg of the final value. 2 DIGITAL OUTPUT FOR THE ADXL355 TA = 25C, VSUPPLY = 3.3 V, x-axis acceleration and y-axis acceleration = 0 g, and z-axis acceleration = 1 g, and output data rate (ODR) = 500 Hz, unless otherwise noted. Note that multifunction pin names may be referenced by their relevant function only. Table 2. Parameter SENSOR INPUT Output Full Scale Range (FSR) Test Conditions/Comments Each axis User selectable Nonlinearity Cross Axis Sensitivity SENSITIVITY X-Axis, Y-Axis, and Z-Axis Sensitivity 2 g X-Axis, Y-Axis, and Z-Axis Scale Factor Sensitivity Change due to Temperature 0 g OFFSET X-Axis, Y-Axis, and Z-Axis 0 g Output 0 g Offset vs. Temperature (X-Axis, Y-Axis, and Z-Axis)1 Repeatability2 Vibration Rectification3 NOISE DENSITY X-Axis, Y-Axis, and Z-Axis Velocity Random Walk OUTPUT DATA RATE AND BANDWIDTH Low-Pass Filter Passband Frequency High-Pass Filter Passband Frequency When Enabled (Disabled by Default) Each axis 2 g 4 g 8 g 2 g 4 g 8 g -40C to +125C Each axis, 2 g -40C to +125C X-axis and y-axis Z-axis 2 g range, in a 1 g orientation, offset due to 2.5 g rms vibration 2 g Min Rev. A | Page 4 of 42 Max Unit g g g % FS % 2.048 4.096 8.192 0.1 1 235,520 117,760 58,880 256,000 128,000 64,000 3.9 7.8 15.6 0.01 276,480 138,240 69,120 LSB/g LSB/g LSB/g g/LSB g/LSB g/LSB %/C -75 -0.15 25 0.02 3.5 9 <0.4 +75 +0.15 mg mg/C mg mg g 25 9 13 X-axis and y-axis Z-axis User programmable, Register 0x28 User programmable, Register 0x28 for 4 kHz ODR Typ 1 0.0095 g/Hz m/sec/Hr m/sec/Hr 1000 10 Hz Hz Data Sheet ADXL354/ADXL355 Parameter SELF TEST Output Change X-Axis Y-Axis Z-Axis POWER SUPPLY Voltage Range VSUPPLY Operating4 VDDIO V1P8ANA and V1P8DIG with Internal LDO Bypassed Current Measurement Mode VSUPPLY (LDO Enabled) V1P8ANA (LDO Disabled) V1P8DIG (LDO Disabled) Standby Mode VSUPPLY (LDO Enabled) V1P8ANA (LDO Disabled) V1P8DIG (LDO Disabled) Turn On Time5 Test Conditions/Comments Min Typ Max g g g 0.3 0.3 1.5 VSUPPLY = 0 V 2.25 V1P8DIG 1.62 2 g range Power-off to standby TEMPERATURE SENSOR Output at 25C Scale Factor TEMPERATURE Operating Temperature Range 2.5 2.5 1.8 Unit 3.6 3.6 1.98 V V V 200 160 35.5 A A A 21 7 10 <10 <10 A A A ms ms 1852 -9.05 LSB LSB/C -40 +125 C 1 The temperature change is -40C to +25C or +25C to +125C. Repeatability is predicted for a 10 year life and includes shifts due to the HTOL (TA = 150C, VSUPPLY = 3.6 V, and 1000 hours), temperature cycling (-55C to +125C and 1000 cycles), velocity random walk, broadband noise, and temperature hysteresis. 3 The VRE measurement is the shift in dc offset while the device is subject to 2.5 g rms random vibration from 50 Hz to 2 kHz. The DUT is configured for the 2 g range and an output data rate of 4 kHz. The VRE scales with the range setting. 4 When V1P8ANA and V1P8DIG are generated internally, VSUPPLY is valid. To disable the LDO and drive V1P8ANA and V1P8DIG externally, connect VSUPPLY to VSS. 5 Standby to measurement mode; valid when the output is within 1 mg of final value. 2 SPI DIGITAL INTERFACE CHARACTERISTICS FOR THE ADXL355 Note that multifunction pin names may be referenced by their relevant function only. Table 3. Parameter DC INPUT LEVELS Input Voltage Low Level High Level Input Current Low Level High Level DC OUTPUT LEVELS Output Voltage Low Level High Level Output Current Low Level High Level Symbol Test Conditions/Comments VIL VIH Min Typ Max Unit 0.3 x VDDIO V V 0.7 x VDDIO IIL IIH VIN = 0 V VIN = VDDIO VOL VOH IOL = IOL, MIN IOH = IOH, MAX IOL IOH VOL = VOL, MAX VOH = VOH, MIN -0.1 0.1 0.2 x VDDIO 0.8 x VDDIO -10 4 Rev. A | Page 5 of 42 A A V V mA mA ADXL354/ADXL355 Data Sheet Parameter AC INPUT LEVELS SCLK Frequency SCLK High Time SCLK Low Time CS Setup Time CS Hold Time CS Disable Time Rising SCLK Setup Time MOSI Setup Time MOSI Hold Time AC OUTPUT LEVELS Propagation Delay Enable MISO Time Disable MISO Time Symbol Test Conditions/Comments Min Typ 0.1 40 40 20 20 40 20 20 20 tHIGH tLOW tCSS tCSH tCSD tSCLKS tSU tHD tP tEN tDIS CLOAD = 30 pF Max Unit 10 MHz ns ns ns ns ns ns ns ns 30 ns ns ns 30 20 tCSD CS tCSS tHIGH tCSH tLOW tSCLKS SCLK tSU tHD MOSI tDIS tP 14205-003 tEN MISO Figure 3. SPI Interface Timing Diagram I2C DIGITAL INTERFACE CHARACTERISTICS FOR THE ADXL355 Note that multifunction pin names may be referenced by their relevant function only. Table 4. Parameter DC INPUT LEVELS Input Voltage Low Level High Level Hysteresis of Schmitt Trigger Inputs Input Current DC OUTPUT LEVELS Output Voltage Low Level Output Current Low Level Symbol Test Conditions/ Comments VIL VIH VHYS IIL VOL1 VOL2 IOL Min I2C_HS = 0 (Fast Mode) Typ Max I2C_HS = 1 (High Speed Mode) Min Typ Max 0.3 x VDDIO 0.7 x VDDIO 0.05 x VDDIO 0.1 x VDDIO < VIN < 0.9 x VDDIO -10 IOL = 3 mA VDD > 2 V VDD 2 V VOL = 0.4 V VOL = 0.6 V 20 6 Rev. A | Page 6 of 42 0.3 x VDDIO 0.7 x VDDIO 0.1 x VDDIO Unit V V A +10 A 0.4 0.2 x VDDIO V V mA mA Data Sheet ADXL354/ADXL355 Parameter AC INPUT LEVELS SCLK Frequency SCL High Time SCL Low Time Start Setup Time Start Hold Time SDA Setup Time SDA Hold Time Stop Setup Time Bus Free Time SCL Input Rise Time SCL Input Fall Time SDA Input Rise Time SDA Input Fall Time Width of Spikes to Suppress AC OUTPUT LEVELS Propagation Delay Data Acknowledge Output Fall Time Symbol tHIGH tLOW tSUSTA tHDSTA tSUDAT tHDDAT tSUSTO tBUF tRCL tFCL tRDA tFDA tSP Test Conditions/ Comments Min I2C_HS = 0 (Fast Mode) Typ Max 0 260 500 260 260 50 0 260 500 I2C_HS = 1 (High Speed Mode) Min Typ Max 1 0 60 160 160 160 10 0 160 3.4 120 120 120 120 50 Not shown in Figure 4 Unit MHz ns ns ns ns ns ns ns ns ns ns ns ns ns 80 80 160 160 10 CLOAD = 500 pF tVDDAT tVDACK tF 97 Not shown in Figure 4 450 450 120 20 x (VDD/5.5) 27 tFDA 135 tRDA ns ns ns tBUF SDA tVDDAT tSUDAT tHDDAT tLOW tVDDAT SCL Figure 4. I2C Interface Timing Diagram Rev. A | Page 7 of 42 tVDACK tFCL tHIGH tRCL tSUSTO tSUSTA 14205-004 tSUSTA tHDSTA ADXL354/ADXL355 Data Sheet ABSOLUTE MAXIMUM RATINGS the maximum operating conditions for extended periods may affect product reliability. Table 5. Parameter Acceleration (Any Axis, 0.1 ms) Unpowered Vibration VSUPPLY, VDDIO V1P8ANA, V1P8DIG Configured as Inputs ADXL354 Digital Inputs (RANGE, ST1, ST2, STBY) Analog Outputs (XOUT, YOUT, ZOUT, TEMP) ADXL355 Digital Pins (CS, SCLK, MOSI, MISO, INT1, INT2, DRDY) Operating Temperature Range Storage Temperature Range Rating THERMAL RESISTANCE 5,000 g Per MIL-STD-883 Method 2007, Test Condition A 5.4 V 1.98 V Thermal performance is directly linked to printed circuit board (PCB) design and operating environment. Careful attention to PCB thermal design is required. -0.3 V to VDDIO + 0.3 V -0.3 V to V1P8ANA + 0.3 V 1 Table 6. Thermal Resistance Package Type E-14-11 -0.3 V to VDDIO + 0.3 V JA 42 Unit C/W Thermal impedance simulated values are based on a JEDEC 2S2P thermal test board with four thermal vias. See JEDEC JESD51. ESD CAUTION -40C to +125C -55C to +150C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond Rev. A | Page 8 of 42 Data Sheet ADXL354/ADXL355 12 X OUT Y 11 VSUPPLY RANGE 1 ST1 2 ADXL354 10 V1P8ANA ST2 3 TOP VIEW (Not to Scale) 9 VSS 8 V1P8DIG Z STBY 7 VSSIO 6 VDDIO 5 TEMP 4 X 14205-007 13 Y OUT 14 ZOUT PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 5. ADXL354 Pin Configuration Table 7. ADXL354 Pin Function Descriptions Pin No. 1 Mnemonic RANGE 2 3 4 5 6 7 ST1 ST2 TEMP VDDIO VSSIO STBY 8 V1P8DIG 9 10 VSS V1P8ANA 11 VSUPPLY 12 13 14 XOUT YOUT ZOUT Description Range Selection Pin. Set this pin to ground to select the 2 g range, or set this pin to VDDIO to select the 4 g or 8 g range. This pin is model dependent (see the Ordering Guide section). Self Test Pin 1. This pin enables self test mode. Self Test Pin 2. This pin activates the electromechanical self test actuation. Temperature Sensor Output. Digital Interface Supply Voltage. Digital Ground. Standby or Measurement Mode Selection Pin. Set this pin to ground to enter standby mode, or set this pin to VDDIO to enter measurement mode. Digital Supply. This pin requires a decoupling capacitor. If VSUPPLY connects to VSS, supply the voltage to this pin externally. Analog Ground. Analog Supply. This pin requires a decoupling capacitor. If VSUPPLY connects to VSS, supply the voltage to this pin externally. Supply Voltage. When VSUPPLY equals 2.25 V to 3.6 V, VSUPPLY enables the internal LDOs to generate V1P8DIG and V1P8ANA. For VSUPPLY = VSS, V1P8DIG and V1P8ANA are externally supplied. X-Axis Output. Y-Axis Output. Z-Axis Output. Rev. A | Page 9 of 42 12 INT1 Y 11 VSUPPLY CS/SCL 1 SCLK/VSSIO 2 ADXL355 10 V1P8ANA MOSI/SDA 3 TOP VIEW (Not to Scale) 9 VSS 8 V1P8DIG X Z RESERVED 7 VSSIO 6 VDDIO 5 MISO/ASEL 4 14205-006 13 INT2 Data Sheet 14 DRDY ADXL354/ADXL355 Figure 6. ADXL355 Pin Configuration Table 8. ADXL355 Pin Function Descriptions Pin No. 1 Mnemonic CS/SCL 2 SCLK/VSSIO 3 MOSI/SDA 4 MISO/ASEL 5 6 7 8 VDDIO VSSIO RESERVED V1P8DIG 9 10 VSS V1P8ANA 11 VSUPPLY 12 13 14 INT1 INT2 DRDY Description Chip Select for SPI (CS). Serial Communications Clock for I2C (SCL). Serial Communications Clock for SPI (SCLK). Connect to VSSIO for I2C (VSSIO). Master Output, Slave Input for SPI (MOSI). Serial Data for I2C (SDA). Master Input, Slave Output for SPI (MISO). Alternate I2C Address Select for I2C (ASEL). Digital Interface Supply Voltage. Digital Ground. Reserved. This pin can be connected to ground or left open. Digital Supply. This pin requires a decoupling capacitor. If VSUPPLY connects to VSS, supply the voltage to this pin externally. Analog Ground. Analog Supply. This pin requires a decoupling capacitor. If VSUPPLY connects to VSS, supply the voltage to this pin externally. Supply Voltage. When VSUPPLY equals 2.25 V to 3.6 V, VSUPPLY enables the internal LDOs to generate V1P8DIG and V1P8ANA. For VSUPPLY = VSS, V1P8DIG and V1P8ANA are externally supplied. Interrupt Pin 1. Interrupt Pin 2. Data Ready Pin. Rev. A | Page 10 of 42 Data Sheet ADXL354/ADXL355 TYPICAL PERFORMANCE CHARACTERISTICS All figures include data for multiple devices and multiple lots, and they were taken in the 2 g range, unless otherwise noted. 1 10 XOUT (g) 1 0.1 100 1000 FREQUENCY (Hz) 0.01 10 14205-207 0.01 10 Figure 7. ADXL354 Frequency Response for X-Axis 100 1000 FREQUENCY (Hz) 14205-210 0.1 Figure 10. ADXL355 Normalized Frequency Response for X-Axis at 4 kHz ODR 10 1 Y-AXIS (g) YOUT (g) 1 0.1 1000 FREQUENCY (Hz) 0.01 10 Figure 11. ADXL355 Normalized Frequency Response for Y-Axis at 4 kHz ODR 10 Z-AXIS (g) 1 1 100 1000 FREQUENCY (Hz) 14205-209 ZOUT (g) 1000 FREQUENCY (Hz) Figure 8. ADXL354 Frequency Response for Y-Axis 0.1 10 100 14205-211 100 0.1 0.01 10 100 FREQUENCY (Hz) Figure 9. ADXL354 Frequency Response for Z-Axis 1000 14205-212 0.01 10 14205-208 0.1 Figure 12. ADXL355 Normalized Frequency Response for Z-Axis at 4 kHz ODR Rev. A | Page 11 of 42 ADXL354/ADXL355 15.00 Data Sheet 1.00 MAXIMUM CHANGE = 1.69mg AVERAGE CHANGE = 1.18mg MAXIMUM CHANGE = 0.60% AVERAGE CHANGE = 0.34% RELATIVE SENSITIVITY (%) RELATIVE OFFSET (mg) 10.00 5.00 0 0.50 0 -5.00 55 105 TEMPERATURE (C) -0.65 -45 14205-213 5 105 Figure 16. ADXL354 X-Axis Sensitivity Relative to 25C vs. Temperature 1.00 MAXIMUM CHANGE = 3.12mg AVERAGE CHANGE = 1.85mg MAXIMUM CHANGE = 0.54% AVERAGE CHANGE = 0.28% RELATIVE SENSITIVITY (%) 10.00 RELATIVE OFFSET (mg) 55 TEMPERATURE (C) Figure 13. ADXL354 X-Axis Zero g Offset Relative to 25C vs. Temperature 15.00 5 14205-216 -0.50 -9.75 -45 5.00 0 0.50 0 -5.00 5 55 105 TEMPERATURE (C) -0.65 -45 14205-214 -9.75 -45 55 105 TEMPERATURE (C) Figure 14. ADXL354 Y-Axis Zero g Offset Relative to 25C vs. Temperature 15.00 5 14205-217 -0.50 Figure 17. ADXL354 Y-Axis Sensitivity Relative to 25C vs. Temperature 1.00 MAXIMUM CHANGE = 3.12mg AVERAGE CHANGE = 1.85mg MAXIMUM CHANGE = 0.99% AVERAGE CHANGE = 0.51% RELATIVE SENSITIVITY (%) RELATIVE OFFSET (mg) 10.00 5.00 0 0.50 0 -5.00 55 TEMPERATURE (C) 105 -0.65 -40 14205-215 5 10 60 TEMPERATURE (C) Figure 15. ADXL354 Z-Axis Zero g Offset Relative to 25C vs. Temperature 110 14205-218 -0.50 -9.75 -45 Figure 18. ADXL354 Z-Axis Sensitivity Relative to 25C vs. Temperature Rev. A | Page 12 of 42 ADXL354 2g OFFSET Z-AXIS (g) 40 30 20 0 0 ADXL354 2g SENSITIVITY X-AXIS (V/g) Figure 19. ADXL354 Zero g Offset Histogram at 25C, X-Axis 80 80 70 70 60 60 40 30 20 10 10 0 0 ADXL354 2g SENSITIVITY Y-AXIS (V/g) Figure 20. ADXL354 Zero g Offset Histogram at 25C, Y-Axis 45 40 25 20 15 5 0 0 Figure 21. ADXL354 Zero g Offset Histogram at 25C, Z-Axis Rev. A | Page 13 of 42 ADXL354 2g SENSITIVITY Z-AXIS (V/g) Figure 24. ADXL354 Sensitivity Histogram at 25C, Z-Axis 14205-222 70 14205-223 10 0.368 0.370 0.372 0.374 0.376 0.378 0.380 0.382 0.384 0.386 0.388 0.390 0.392 0.394 0.396 0.398 0.400 0.402 0.404 0.406 0.408 0.410 0.412 0.414 0.416 0.418 0.420 0.422 0.424 0.426 0.428 0.430 0.432 50 HITS PER BIN (Count) 60 0.368 0.370 0.372 0.374 0.376 0.378 0.380 0.382 0.384 0.386 0.388 0.390 0.392 0.394 0.396 0.398 0.400 0.402 0.404 0.406 0.408 0.410 0.412 0.414 0.416 0.418 0.420 0.422 0.424 0.426 0.428 0.430 0.432 50 HITS PER BIN (Count) 14205-219 80 14205-224 ADXL354 2g OFFSET Y-AXIS (g) 14205-220 10 0.075 0.070 0.065 0.060 0.055 0.050 0.045 -0.040 -0.035 -0.030 -0.025 -0.020 -0.015 -0.010 -0.005 0 0.005 0.010 0.015 0.020 0.025 0.030 0.035 0.040 0.045 0.050 0.055 0.060 0.065 0.070 0.075 HITS PER BIN (Count) 70 0.368 0.370 0.372 0.374 0.376 0.378 0.375 0.377 0.379 0.381 0.383 0.385 0.387 0.389 0.391 0.393 0.395 0.397 0.399 0.401 0.403 0.405 0.407 0.409 0.416 0.418 0.420 0.422 0.424 0.426 0.428 0.430 0.432 30 HITS PER BIN (Count) 20 0.075 0.070 0.065 0.060 0.055 0.050 0.045 -0.040 -0.035 -0.030 -0.025 -0.020 -0.015 -0.010 -0.005 0 0.005 0.010 0.015 0.020 0.025 0.030 0.035 0.040 0.045 0.050 0.055 0.060 0.065 0.070 0.075 HITS PER BIN (Count) ADXL354 2g OFFSET X-AXIS (g) 14205-221 HITS PER BIN (Count) Data Sheet ADXL354/ADXL355 60 50 40 30 20 Figure 22. ADXL354 Sensitivity Histogram at 25C, X-Axis 50 40 30 Figure 23. ADXL354 Sensitivity Histogram at 25C, Y-Axis 70 35 60 50 40 30 10 20 10 Data Sheet 0.68 0.6 0.58 0.5 0.48 0.4 0.3 0.38 0.28 0.2 0.18 0.1 0.08 0 0 1 2 3 4 INPUT VIBRATION (g rms) -0.02 0 2 4 6 8 10 INPUT VIBRATION (g rms) 14205-228 OFFSET SHIFT (g) 0.7 14205-225 OFFSET SHIFT (g) ADXL354/ADXL355 Figure 28. ADXL354 Vibration Rectification Error (VRE), X-Axis Offset from +1 g, 8 g Range, X-Axis Orientation = -1 g Figure 25. ADXL354 Vibration Rectification Error (VRE), X-Axis Offset from +1 g, 2 g Range, X-Axis Orientation = -1 g 0 0 -0.1 -0.1 -0.4 -0.3 -0.4 -0.5 -0.5 -0.6 -0.6 0 1 2 INPUT VIBRATION (g rms) 3 4 -0.7 -0.1 -0.1 -0.2 -0.2 OFFSET SHIFT (g) 0 -0.3 -0.4 -0.6 4 INPUT VIBRATION (g rms) 14205-227 -0.6 3 8 10 -0.4 -0.5 2 6 -0.3 -0.5 1 4 Figure 29. ADXL354 Vibration Rectification Error (VRE), Y-Axis Offset from +1 g, 8 g Range, Y-Axis Orientation = +1 g 0 0 2 INPUT VIBRATION (g rms) Figure 26. ADXL354 Vibration Rectification Error (VRE), Y-Axis Offset from +1 g, 2 g Range, Y-Axis Orientation = +1 g -0.7 0 -0.7 0 2 4 6 8 10 INPUT VIBRATION (g rms) Figure 30. ADXL354 Vibration Rectification Error (VRE), Z-Axis Offset from +1 g, 8 g Range, Z-Axis Orientation = +1 g Figure 27. ADXL354 Vibration Rectification Error (VRE), Z-Axis Offset from +1 g, 2 g Range, Z-Axis Orientation = +1 g Rev. A | Page 14 of 42 14205-230 -0.7 OFFSET SHIFT (g) -0.2 14205-229 OFFSET SHIFT (g) -0.3 14205-226 OFFSET SHIFT (g) -0.2 Data Sheet ADXL354/ADXL355 15.00 1.00 MAXIMUM DELTA = 6.5mg AVERAGE DELTA = 1.7mg RELATIVE SENSITIVITY (%) RELATIVE OFFSET (mg) 10.00 5.00 0 MAXIMUM CHANGE = 0.78% AVERAGE CHANGE = 0.72% 0.50 0 -5.00 55 105 TEMPERATURE (C) -0.65 -45 14205-231 5 5 55 105 TEMPERATURE (C) Figure 31. ADXL355 X-Axis Zero g Offset Relative to 25C vs. Temperature 14205-234 -0.50 -9.75 -45 Figure 34. ADXL355 X-Axis Sensitivity Relative to 25C vs. Temperature 1.00 15.00 MAXIMUM DELTA = 3.2mg AVERAGE DELTA = 1.4mg MAXIMUM CHANGE = 0.78% AVERAGE CHANGE = 0.72% RELATIVE SENSTIVITY (%) RELATIVE OFFSET (mg) 10.00 5.00 0 0.50 0 -5.00 5 55 105 TEMPERATURE (C) -0.65 -45 14205-232 -9.75 -45 5 55 105 TEMPERATURE (C) Figure 32. ADXL355 Y-Axis Zero g Offset Relative to 25C vs. Temperature 14205-235 -0.50 Figure 35. ADXL355 Y-Axis Sensitivity Relative to 25C vs. Temperature 1.00 15.00 MAXIMUM DELTA = 10.6mg AVERAGE DELTA = 5.3mg MAXIMUM CHANGE = 0.47% AVERAGE CHANGE = 0.3% RELATIVE SENSTIVITY (%) RELATIVE OFFSET (mg) 10.00 5.00 0 0.50 0 -5.00 55 TEMPERATURE (C) 105 -0.65 -45 14205-233 5 Figure 33. ADXL355 Z-Axis Zero g Offset Relative to 25C vs. Temperature 5 55 TEMPERATURE (C) 105 14205-236 -0.50 -9.75 -45 Figure 36. ADXL355 Z-Axis Sensitivity Relative to 25C vs. Temperature Rev. A | Page 15 of 42 0 OFFSET (mg) Figure 37. ADXL355 Zero g Offset Histogram at 25C, X-Axis 80 40 30 10 0 Figure 38. ADXL355 Zero g Offset Histogram at 25C, Y-Axis SENSITIVITY (LSB/g) 45 25 20 15 0 Figure 39. ADXL355 Zero g Offset Histogram at 25C, Z-Axis Figure 42. ADXL355 Sensitivity Histogram at 25C, Z-Axis SENSITIVITY (LSB/g) Rev. A | Page 16 of 42 14205-240 SENSITIVITY (lsb/g) 14205-241 0 14205-242 30 235520 237158 238797 240435 242074 243712 245350 246989 248627 250266 251904 253542 255181 256819 258458 260096 261734 263373 265011 266650 268288 269926 271565 273203 274842 276480 40 HITS PER BIN (Count) 50 235520 237158 238797 240435 242074 243712 245350 246989 248627 250266 251904 253542 255181 256819 258458 260096 261734 263373 265011 266650 268288 269926 271565 273203 274842 276480 50 HITS PER BIN (Count) 14205-237 -75 -69 -63 -57 -51 -45 -39 -33 -27 -21 -15 -9 -3 3 9 15 21 27 33 39 45 51 57 63 69 75 HITS PER BIN (Count) 80 235520 237158 238797 240435 242074 243712 245350 246989 248627 250266 251904 253542 255181 256819 258458 260096 261734 263373 265011 266650 268288 269926 271565 273203 274842 276480 30 HITS PER BIN (Count) OFFSET (mg) 14205-238 OFFSET (mg) 14205-239 0 -75 -69 -63 -57 -51 -45 -39 -33 -27 -21 -15 -9 -3 3 9 15 21 27 33 39 45 51 57 63 69 75 HITS PER BIN (Count) 0 -75 -69 -63 -57 -51 -45 -39 -33 -27 -21 -15 -9 -3 3 9 15 21 27 33 39 45 51 57 63 69 75 HITS PER BIN (Count) ADXL354/ADXL355 Data Sheet 60 70 60 50 40 30 20 20 10 10 Figure 40. ADXL355 Sensitivity Histogram at 25C, X-Axis 60 70 60 50 40 30 20 20 10 Figure 41. ADXL355 Sensitivity Histogram at 25C, Y-Axis 60 40 35 50 40 30 20 10 5 10 ADXL354/ADXL355 0.68 0.6 0.58 0.5 0.48 0.4 0.3 0.38 0.28 0.2 0.18 0.1 0.08 0 0 1 2 3 4 INPUT VIBRATION (g rms) -0.02 0 2 4 6 8 10 INPUT VIBRATION (g rms) Figure 43. ADXL355 Vibration Rectification Error (VRE), X-Axis Offset from +1 g, 2 g Range, X-Axis Orientation = -1 g 14205-246 OFFSET SHIFT (g) 0.7 14205-243 OFFSET CHANGE (g) Data Sheet Figure 46. ADXL355 Vibration Rectification Error (VRE), X-Axis Offset from +1 g, 8 g Range, X-Axis Orientation = -1 g 0 0 -0.1 OFFSET SHIFT (g) -0.3 -0.4 -0.5 -0.4 1 2 3 4 -0.7 14205-244 0 -0.1 -0.1 -0.2 -0.2 OFFSET SHIFT (g) 0 -0.3 -0.4 -0.6 3 4 14205-245 -0.6 2 8 10 -0.4 -0.5 INPUT VIBRATION (g rms) 6 -0.3 -0.5 1 4 Figure 47. ADXL355 Vibration Rectification Error (VRE), Y-Axis Offset from +1 g, 8 g Range, Y-Axis Orientation = +1 g 0 0 2 INPUT VIBRATION (g rms) Figure 44. ADXL355 Vibration Rectification Error (VRE), Y-Axis Offset from +1 g, 2 g Range, Y-Axis Orientation = +1 g -0.7 0 14205-247 -0.6 INPUT VIBRATION (g rms) OFFSET CHANGE (g) -0.3 -0.5 -0.6 -0.7 -0.2 Figure 45. ADXL355 Vibration Rectification Error (VRE), Z-Axis Offset from +1 g, 2 g Range, Z-Axis Orientation = +1 g -0.7 0 2 4 6 8 10 INPUT VIBRATION (g rms) Figure 48. ADXL355 Vibration Rectification Error (VRE), Z-Axis Offset from +1 g, 8 g Range, Z-Axis Orientation = +1 g Rev. A | Page 17 of 42 14205-248 OFFSET CHANGE (g) -0.1 -0.2 0.004 1.15 0.002 1.05 0 0.95 -0.002 -0.004 0.75 -40 10 60 110 -0.006 14205-249 0.85 ADXL354 TEMPERATURE SENSOR LINEAR OFFSET (V) 1.25 TEMPERATURE (C) Figure 49. ADXL354 Temperature Sensor Output and Linearity Offset vs. Temperature 2300 6 2100 4 1900 2 1700 0 1500 -2 1300 -4 1100 -6 900 TEMPERATURE SENSOR OUTPUT LINEARITY 700 -40 14205-250 0.006 TEMPERATURE SENSOR OUTPUT LINEARITY -8 10 60 TEMPERATURE (C) 110 Figure 52. ADXL355 Temperature Sensor Output and Linearity Offset vs. Temperature 80 100 90 70 80 HITS PER BIN (Count) 60 50 40 30 20 50 40 30 14205-251 10 0 125 129 133 137 141 145 149 153 157 161 165 169 173 TOTAL SUPPLY CURRENT (A) Figure 50. ADXL354 Total Supply Current, 3.3 V 30 25 20 15 10 ADXL355 CLOCK FREQUENCY (Hz) 14205-252 5 3800 3840 3880 3920 3960 4000 4040 4080 4120 4160 4200 0 180 184 188 192 196 200 204 208 212 216 220 224 228 TOTAL SUPPLY CURRENT (A) Figure 53. ADXL355 Total Supply Current, 3.3 V 35 HITS PER BIN (Count) 60 20 10 0 70 Figure 51. ADXL355 Internal Clock Frequency Histogram Rev. A | Page 18 of 42 14205-253 HITS PER BIN (Count) ADXL354 TEMPERATURE SENSOR OUTPUT (V) 1.35 ADXL355 TEMPERATURE SENSOR LINEAR OFFSET (LSB) Data Sheet ADXL355 TEMPERATURE SENSOR OUTPUT (LSB) ADXL354/ADXL355 Data Sheet ADXL354/ADXL355 ROOT ALLAN VARIANCE (RAV) ADXL355 CHARACTERISTICS All figures include data for multiple devices and multiple lots, and they were taken in the 2 g range, unless otherwise noted. 1000 100 100 RAV (g) RAV (g) 1000 0.1 1 10 100 1000 INTEGRATION TIME (Seconds) 14205-254 1 0.01 1000 RAV (g) 100 1 10 100 INTEGRATION TIME (Seconds) 1000 14205-255 10 0.1 0.1 1 10 100 1000 INTEGRATION TIME (Seconds) Figure 56. ADXL355 Root Allan Variance (RAV), Z-Axis Figure 54. ADXL355 Root Allan Variance (RAV), X-Axis 1 0.01 1 0.01 Figure 55. ADXL355 Root Allan Variance (RAV), Y-Axis Rev. A | Page 19 of 42 14205-256 10 10 ADXL354/ADXL355 Data Sheet THEORY OF OPERATION VDDIO (4g, 8g) GND ( 2g) 0.1F 11 VSUPPLY RANGE 1 10 V1P8ANA ST1 2 ST2 3 2.25V TO 3.6V 0.1F ADXL354 STBY 7 VSSIO 6 VDDIO 5 TEMP 4 9 VSS 8 V1P8DIG ADC VREF VDDIO (MEASUREMENT) GND (STANDBY) 1F 1F 0.1F 0.1F 2.25V TO 3.6V Figure 57. ADXL354 Application Circuit Rev. A | Page 20 of 42 1F 1F 14205-022 The ADXL355 includes antialias filters before and after the high resolution - ADC. User-selectable output data rates and filter corners are provided. The temperature sensor is digitized with a 12-bit successive approximation register (SAR) ADC. The ADXL354 outputs two forms of filtering: internal antialiasing filtering with a cutoff frequency of approximately 1.5 kHz, and external filtering. The external filter uses a fixed, on-chip, 32 k resistance in series with each output in conjunction with the external capacitors to implement the low-pass filter antialiasing and noise reduction prior to the external ADC. The antialias filter cutoff frequency must be significantly higher than the desired signal bandwidth. If the antialias filter corner is too low, ratiometricity can be degraded where the signal attenuation is different than the reference attenuation. 12 XOUT The analog accelerometer outputs of the ADXL354 are ratiometric to V1P8ANA; therefore, carefully digitize them correctly. The temperature sensor output is not ratiometric. The XOUT, YOUT, and ZOUT analog outputs are filtered internally with an antialiasing filter. These analog outputs also have an internal 32 k series resistor that can be used with an external capacitor to set the bandwidth of the output. Figure 57 shows the ADXL354 application circuit. The analog outputs (XOUT, YOUT, and ZOUT) are ratiometric to the 1.8 V analog voltage from the V1P8ANA pin. V1P8ANA can be powered with an on-chip LDO that is powered from VSUPPLY. V1P8ANA can also be supplied externally by forcing VSUPPLY to VSS, which disables the LDO. Due to the ratiometric response, the analog output requires referencing to the V1P8ANA supply when digitizing to achieve the inherent noise and offset performance of the ADXL354. The 0 g bias output is nominally equal to V1P8ANA/2. The recommended option is to use the ADXL354 with a ratiometric ADC (for example, the Analog Devices, Inc., AD7682) with V1P8ANA providing the voltage reference. This configuration results in self cancellation of errors due to minor supply variations. 13 YOUT The micromachined, sensing elements are fully differential, comprising the lateral x-axis and y-axis sensors and the vertical, teeter totter z-axis sensors. The x-axis and y-axis sensors and the z-axis sensors go through separate signal paths that minimize offset drift and noise. The signal path is fully differential, except for a differential to single-ended conversion at the analog outputs of the ADXL354. ANALOG OUTPUT 14 ZOUT The ADXL354 is a complete 3-axis, ultralow noise and ultrastable offset MEMS accelerometer with outputs ratiometric to the analog 1.8 V supply, V1P8ANA. The ADXL355 adds three high resolution ADCs that use the analog 1.8 V supply as a reference to provide digital outputs insensitive to the supply voltage. The ADXL354B is pin selectable for 2 g or 4 g full scale, the ADXL354C is pin selectable for 2 g or 8 g full scale, and the ADXL355 is programmable for 2.048 g, 4.096 g, and 8.192 g full scale. The ADXL355 offers both SPI and I2C communications ports. Data Sheet ADXL354/ADXL355 DIGITAL OUTPUT AXES OF ACCELERATION SENSITIVITY Figure 59 shows the ADXL355 application circuit with the recommended bypass capacitors. The communications interface is either SPI or I2C (see the Serial Communications section for additional information). Figure 58 shows the axes of acceleration sensitivity. Note that the output voltage increases when accelerated along the sensitive axis. Z The ADXL355 includes an internal configurable digital bandpass filter. Both the high-pass and low-pass poles of the filter are adjustable, as detailed in the Filter Settings Register section and Table 43. At power-up, the default conditions for the filters are as follows: X 1F 10 V1P8ANA ADXL355 0.1F TOP VIEW (Not to Scale) VSS 8 V1P8DIG 1F RESERVED 7 VSSIO 6 VDDIO 5 MISO/ASEL 4 9 1F 1F 0.1F 0.1F 2.25V TO 3.6V Figure 59. ADXL355 Application Circuit Rev. A | Page 21 of 42 14205-021 MOSI/SDA 3 0.1F 11 VSUPPLY CS/SCL 1 SCLK/VSSIO 2 2.25V TO 3.6V 12 INT1 13 INT2 14 DRDY Figure 58. Axes of Acceleration Sensitivity 14205-005 High-pass filter (HPF) = dc (off) Low-pass filter (LPF) = 1000 Hz Output data rate = 4000 Hz SPI/I2C INTERFACE Y ADXL354/ADXL355 Data Sheet POWER SEQUENCING VDDIO There are two methods for applying power to the device. Typically, internal LDO regulators generate the 1.8 V power for the analog and digital supplies, V1P8ANA and V1P8DIG, respectively. Optionally, connecting VSUPPLY to VSS and driving V1P8ANA and V1P8DIG with an external supply can supply V1P8ANA and V1P8DIG. The VDDIO value determines the logic high levels. On the analog output ADXL354, VDDIO sets the logic high level for the self test pins, ST1 and ST2, as well as the STBY pin. On the digital output ADXL355, VDDIO sets the logic high level for communications interface ports, as well as the interrupt and DRDY outputs. When using the internal LDO regulators, connect VSUPPLY to a voltage source between 2.25 V to 3.6 V. In this case, VDDIO and VSUPPLY can be powered in parallel. VSUPPLY must not exceed the VDDIO voltage by greater than 0.5 V. If necessary, VDDIO can be powered before VSUPPLY. The LDO regulators are operational when VSUPPLY is between 2.25 V and 3.6 V. V1P8ANA and V1P8DIG are the regulator outputs in this mode. Alternatively, when tying VSUPPLY to VSS, V1P8ANA and V1P8DIG are supply voltage inputs with a 1.62 V to 1.98 V range. When disabling the internal LDO regulators and using an external 1.8 V supply to power V1P8ANA and V1P8DIG, tie VSUPPLY to ground, and set V1P8ANA and V1P8DIG to the same final voltage level. In the case of bypassing the LDOs, the recommended power sequence is to apply power to VDDIO, followed by applying power to V1P8DIG approximately 10 s later, and then applying power to V1P8ANA approximately 10 s later. If necessary, V1P8DIG and VDDIO can be powered from the same 1.8 V supply, which can also be tied to V1P8ANA with proper isolation. In this case, proper decoupling and low frequency isolation is important to maintain the noise performance of the sensor. The maximum nominal measurement range for the ADXL354/ ADXL355 is 8 g. Do not subject the device to (or use the device in) applications or assembly processes that reasonably expect to exceed this level of acceleration, particularly for long durations or on an ongoing basis. In such applications, the ADXL356/ ADXL357 offer higher g ranges that may be better suited for such applications. POWER SUPPLY DESCRIPTION The ADXL354/ADXL355 have four different power supply domains: VSUPPLY, V1P8ANA, V1P8DIG, and VDDIO. The internal analog and digital circuitry operates at 1.8 V nominal. OVERRANGE PROTECTION If an overrange event does occur, all sensor drive clocks turn off for 0.5 ms to avoid electrostatic capture of the proof mass when the accelerometer is subject to input acceleration beyond the full-scale range. In the 2 g/2.048 g range setting, the overrange protection activates for input signals beyond approximately 8 g/ 8.192 g (25%), and for the 4 g/4.096 g and 8 g/8.192 g range settings, the threshold corresponds to about 16 g (25%). When overrange protection occurs, the XOUT, YOUT, and ZOUT pins on the ADXL354 begin to drive to midscale. The ADXL355 floats toward zero, and the first in, first out (FIFO) begins filling with this data. VSUPPLY VSUPPLY is 2.25 V to 3.6 V, which is the input range to the two LDO regulators that generate the nominal 1.8 V outputs for V1P8ANA and V1P8DIG. Connect VSUPPLY to VSS to disable the LDO regulators, which allows driving V1P8ANA and V1P8DIG from an external source. SELF TEST V1P8ANA All sensor and analog signal processing circuitry operates in this domain. Offset and sensitivity of the analog output ADXL354 are ratiometric to this supply voltage. When using external ADCs, use V1P8ANA as the reference voltage. The digital output ADXL355 includes ADCs that are ratiometric to V1P8ANA, thereby rendering offset and sensitivity insensitive to the value of V1P8ANA. V1P8ANA can be an input or an output as defined by the state of the VSUPPLY voltage. V1P8DIG V1P8DIG is the supply voltage for the internal logic circuitry. A separate LDO regulator decouples the digital supply noise from the analog signal path. V1P8ANA can be an input or an output as defined by the state of the VSUPPLY voltage. If driven externally, V1P8DIG must be the same voltage as the V1P8ANA voltage. The ADXL354 and ADXL355 incorporate a self test feature that effectively tests their mechanical and electronic systems simultaneously. In ADXL354, drive the ST1 pin to VDDIO to invoke self test mode. Then, by driving the ST2 pin to VDDIO, the ADXL354 applies an electrostatic force to the mechanical sensor and induces a change in output in response to the force. The self test delta (or response) is the difference in output voltages between when ST2 is high and ST2 is low, both when ST1 is asserted. After the self test measurement is complete, bring both pins low to resume normal operation. The self test operation is similar in the ADXL355, except ST1 and ST2 can be accessed through the SELF_TEST register (Register 0x2E). The self test feature rejects externally applied acceleration and only responds to the self test force, which allows an accurate measurement of the self test, even in the presence of external mechanical noise. Rev. A | Page 22 of 42 Data Sheet ADXL354/ADXL355 0 FILTER The ADXL354/ADXL355 use an analog, low-pass, antialiasing filter to reduce out of band noise and to limit bandwidth. The ADXL355 provides further digital filtering options to maintain excellent noise performance at various ODRs. DIGITAL LPF RESPONSE (dB) -10 The analog, low-pass antialiasing filter in the ADXL354/ ADXL355 provides a fixed bandwidth of approximately 1.5 kHz, which is where the output response is attenuated by approximately 50%. The shape of the filter response in the frequency domain is that of a sinc3 filter. -30 -40 -50 -70 1 10 100 INPUT FREQUENCY (Hz) 1k 10k 14205-023 -60 The ADXL354 x-axis, y-axis, and z-axis analog outputs include an amplifier followed by a series 32 k resistor and output to the XOUT, the YOUT, and the ZOUT pins, respectively. The ADXL355 provides an internal 20-bit, - ADC to digitize the filtered analog signal. Additional digital filtering (beyond the analog, low-pass, antialiasing filter) consists of a low-pass digital decimation filter and a bypassable high-pass filter that supports output data rates between 4 kHz and 3.9 Hz. The decimation filter consists of two stages. The first stage is fixed decimation with a 4 kHz ODR with a low-pass filter cutoff (50% reduction in output response) at about 1 kHz. A variable second stage decimation filter is used for the 2 kHz output data rate and below (it is bypassed for 4 kHz ODR). Figure 60 shows the low-pass filter response with a 1 kHz corner (4 kHz ODR) for the ADXL355. Note that Figure 60 does not include the fixed frequency analog, low-pass, antialiasing filter with a fixed bandwidth of approximately 1.5 kHz. -20 Figure 60. ADXL355 Digital Low-Pass Filter (LPF) Response for 4 kHz ODR The ADXL355 pass band of the signal path relates to the combined filter responses, including the analog filter previously discussed, and the digital decimation filter/ODR setting. Table 9 shows the delay associated with the decimation filter for each setting and provides the attenuation at the ODR/4 corner. Table 9. Digital Filter Group Delay and Profile Programmed ODR (Hz) 4000 4000/2 = 2000 4000/4 = 1000 4000/8 = 500 4000/16 = 250 4000/32 = 125 4000/64 = 62.5 4000/128 ~ 31 4000/256 ~ 16 4000/512 ~ 8 4000/1024 ~ 4 Delay ODR (Cycles) Time (ms) 2.52 0.63 2.00 1.00 1.78 1.78 1.63 3.26 1.57 6.27 1.54 12.34 1.51 24.18 1.49 47.59 1.50 96.25 1.50 189.58 1.50 384.31 Rev. A | Page 23 of 42 Attenuation Decimator at ODR/4 (dB) Full Path at ODR/4 (dB) -3.44 -3.63 -2.21 -2.26 -1.92 -1.93 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 -1.83 ADXL354/ADXL355 Data Sheet The ADXL355 also includes an interpolation filter after the decimation filters to produce oversampled/upconverted data that provides an external synchronization option. See the Data Synchronization section for more details. Table 11 shows the delay and attenuation relative to the programmed ODR. Group delay is the digital filter delay from the input to the ADC until data is available at the interface (see the Filter section). This delay is the largest component of the total delay from sensor to serial interface. 40 32.2122 DELAY (ODR CYCLES) The ADXL355 also includes an optional digital high-pass filter with a programmable corner frequency. By default, the highpass filter is disabled. The high pass corner frequency, where the output is attenuated by 50%, is related to the ODR, and the HPF_CORNER setting in the filter register (Register 0x28, Bits[6:4]). Table 10 shows the HPF_CORNER response. Figure 61 and Figure 62 show the simulated high-pass filter response and delay for a 10 Hz cutoff. 30 20 0 9.8801 FREQUENCY (kHz) 14205-025 1 0 -10 Figure 62. High-Pass Filter Delay Response for a 4 kHz ODR and an HPF_CORNER Setting of 001 (Register 0x28, Bits[6:4]) -20 -30 -40 -50 0 9.8801 100 FREQUENCY (kHz) 14205-024 AMPLITUDE RELATIVE TO FULL SCALE (dB) 10 0 -3 Figure 61. High-Pass Filter Pass-Band Response for a 4 kHz ODR and an HPF_CORNER Setting of 001 (Register 0x28, Bits[6:4]) Table 10. Digital High-Pass Filter Response HPF_CORNER Register Setting (Register 0x28, Bits[6:4]) 000 001 010 011 100 101 110 HPF_CORNER Frequency, -3 dB Point Relative to ODR Setting Not applicable, no high-pass filter enabled 24.7 x 10-4 x ODR 6.2084 x 10-4 x ODR 1.5545 x 10-4 x ODR 0.3862 x 10-4 x ODR 0.0954 x 10-4 x ODR 0.0238 x 10-4 x ODR -3 dB at 4 kHz ODR (Hz) Off 9.88 2.48 0.62 0.1545 0.03816 0.00952 Table 11. Combined Digital Interpolation Filter and Decimation Filter Response Interpolator Data Rate Resolution Relative to 64 x ODR (Hz) 64 x 4000 = 256000 64 x 2000 = 128000 64 x 1000 = 64000 64 x 500 = 32000 64 x 250 = 16000 64 x 125 = 8000 64 x 62.5 = 4000 64 x 31.25 = 2000 64 x 15.625 = 1000 64 x 7.8125 = 500 64 x 3.90625 = 250 Combined Interpolator/ Decimator Delay (ODR Cycles) 3.51661 3.0126 2.752 2.6346 2.5773 2.5473 2.53257 2.52452 2.52045 2.5194 2.51714 Combined Interpolator/ Decimator Delay (ms) 0.88 1.51 2.75 5.27 10.31 20.38 40.52 80.78 161.31 322.48 644.39 Rev. A | Page 24 of 42 Combined Interpolator/Decimator Output Attenuation at ODR/4 (dB) -6.18 -4.93 -4.66 -4.58 -4.55 -4.55 -4.55 -4.55 -4.55 -4.55 -4.55 Data Sheet ADXL354/ADXL355 SERIAL COMMUNICATIONS ADXL355 SPI PROTOCOL Wire the ADXL355 for SPI communication as shown in the connection diagram in Figure 63. The SPI protocol timing is shown in Figure 64 to Figure 67. The timing scheme follows the clock polarity (CPOL) = 0 and clock phase (CPHA) = 0. The SPI clock speed ranges from 100 kHz to 10 MHz. PROCESSOR CS DOUT MOSI DOUT MISO DIN SCLK DOUT 14205-026 The 4-wire serial interface communicates in either the SPI or I2C protocol. It affectively autodetects the format being used, requiring no configuration control to select the format. Figure 63. 4-Wire SPI Connection CS 1 2 3 4 5 6 7 A6 A5 A4 A3 A2 A1 8 9 10 11 12 13 14 15 16 D7 D6 D5 D4 D3 D2 D1 D0 15 16 SCLK A0 RW MISO 14205-027 MOSI Figure 64. SPI Timing Diagram--Single-Byte Read CS 1 2 3 4 5 6 7 A6 A5 A4 A3 A2 A1 8 9 10 11 12 13 14 MOSI A0 RW D7 D6 D5 D4 D3 D2 MISO D1 D0 14205-028 SCLK Figure 65. SPI Timing Diagram--Single-Byte Write CS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 SCLK A6 A5 A4 A3 A2 A1 A0 RW BYTE n BYTE 1 D7 D6 D5 D4 D3 D2 D1 D0 D7 MISO D0 D7 D6 D5 D4 D3 D2 D1 D0 14205-029 MOSI Figure 66. SPI Timing Diagram--Multibyte Read CS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 SCLK A6 A5 A4 A3 A2 A1 A0 RW D7 D6 D5 D4 D3 D2 D1 D0 D7 D0 D7 D6 D5 D4 D3 D2 D1 D0 MISO Figure 67. SPI Timing Diagram--Multibyte Write Rev. A | Page 25 of 42 14205-030 BYTE n BYTE 1 MOSI ADXL354/ADXL355 Data Sheet I2C PROTOCOL recent available. It is not guaranteed that XDATA, YDATA, and ZDATA form a set corresponding to one sample point in time. The routine used to retrieve the data from the device controls this data set continuity. If data transfers are initiated when the DATA_RDY bit goes high and completes in a time approximately equal to 1/ODR, XDATA, YDATA, and ZDATA apply to the same data set. Figure 68 to Figure 70 detail the I2C protocol timing. The I2C interface can be used on most buses operating in I2C standard mode (100 kHz), fast mode (400 kHz), fast mode plus (1 MHz), and high speed mode (3.4 MHz). The ADXL355 I2C device ID is as follows: ASEL (pin) = 0, device address = 0x1D ASEL (pin) = 1, device address = 0x53 READING ACCELERATION OR TEMPERATURE DATA FROM THE INTERFACE For multibyte read or write transactions through either serial interface, the internal register address autoincrements. When the top of the register address range, 0x3FF, is reached the autoincrement stops and does not wrap back to Hex Address 0x00. Acceleration data is left justified and has a register address order of most significant data to least significant data, which allows the user to use multibyte transfers and to take only as much data as required--either 8 bits, 16 bits, or 20 bits plus the marker. Temperature data is 12 bits unsigned, right justified. The data in XDATA, YDATA, and ZDATA is always the most The address autoincrement function disables when the FIFO address is used, so that data can be read continuously from the FIFO as a multibyte transaction. In cases where the starting address of a multibyte transaction is less than the FIFO address, the address autoincrements until reaching the FIFO address, and then stops at the FIFO address. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 A6 A5 A4 A3 A2 A1 A0 RW AK SCL REGISTER ADDRESS 0 REPEAT START A6 A5 A4 A3 A2 A1 A0 AK DEVICE ADDRESS A6 A5 A4 A3 A2 DATA BYTE A1 A0 RW AK 0 STOP D6 D5 D4 D3 D2 D1 D0 SINGLE BYTE READ AK INDICATE SDA IS CONTROLLED BY ADXL355 14205-031 DEVICE ADDRESS START SDA 2 Figure 68. I C Timing Diagram--Single-Byte Read 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 DEVICE ADDRESS START REGISTER ADDRESS A6 A5 A4 A3 A2 A1 A0 RW AK SDA 0 DATA BYTE A6 A5 A4 A3 A2 A1 A0 AK D7 D6 D5 D4 D3 D2 D1 D0 AK STOP 14205-032 SCL Figure 69. I2C Timing Diagram--Single-Byte Write 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 19 START SDA DEVICE ADDRESS A6 A5 A4 A3 A2 A1 A0 RW AK REGISTER ADDRESS 0 DATA BYTE 1 A6 A5 A4 A3 A2 A1 A0 AK D7 D6 D5 D4 D3 D2 D1 D0 AK D7 Figure 70. I2C Timing Diagram--Multibyte Write Rev. A | Page 26 of 42 DATA BYTE n D0 AK D7 D6 D5 D4 D3 D2 D1 D0 AK 14205-033 SCL Data Sheet ADXL354/ADXL355 FIFO Figure 71 shows the organization of the data in the FIFO. The acceleration data is twos complement, 20-bit data. The FIFO control logic inserts the two LSB reads on the interface. Bit 1 indicates that an attempt was made to read an empty FIFO, and that the data is not valid acceleration data. Bit 0 is a marker bit to identify the x-axis, which allows a user to verify that the FIFO data was correctly read. An acceleration data point for a given axis occupies one FIFO location. The read pointer, RD_PTR, points to the oldest stored data that was not read already from the interface (see Figure 71). There are no physical x-acceleration, y-acceleration, or z-acceleration data registers. This data also comes directly from the most recent data set in the FIFO, which points to by the z pointer, Z_PTR, (see Figure 71). FIFO operates in a stream mode, that is, when the FIFO overruns new data overwrites the oldest data in the FIFO. A read from the FIFO address guarantees that the three bytes associated with the acceleration measurement on an axis all pertain to the same measurement. The FIFO never overruns, and data is always taken out in sets (multiples of three data points). There are 96 21-bit locations in the FIFO. Each location contains 20 bits of data and a marker bit for the x-axis data. A single-byte read from the FIFO address pops one location from the FIFO. A multibyte read to the FIFO location pops the FIFO on the read of the first byte and every third byte read thereafter. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 Z_PTR Z19 Z18 Z17 Z16 Z15 Z14 Z13 Z12 Z11 Z10 Z9 Z8 Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 0 0 Z_PTR - 1 Y19 Y18 Y17 Y16 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 0 0 Z_PTR - 2 RD_PTR VIRTUAL BITS (NOT ALLOCATED IN THE FIFO) ACCELERATION DATA EMPTY INDICATOR X-AXIS MARKER ASCENDING SPI ADDRESSES Figure 71. FIFO Data Organization Rev. A | Page 27 of 42 14205-035 DATA SET. SAMPLE POINT ASCENDING IS THE SAME ACROSS A SINGLE X-AXIS, Y-AXIS, SPI ADDRESSES AND Z-AXIS DATA SET. ASCENDING FIFO ADDRESSES Z_PTR + 1 ADXL354/ADXL355 Data Sheet INTERRUPTS The status register (Register 0x04) contains five individual bits, four of which can be mapped to either the INT1 pin, the INT2 pin, or both. The polarity of the interrupt, active high or active low, is also selectable via the INT_POL bit in the range (Register 0x2C) register. In general, the status register clears when read, but this is not the case if the condition that caused the interrupt persists after the read of the register. The definition of persist varies slightly in each case, but it is described in the following sections. The DRDY pin is similar to an interrupt pins (INTx) but clears very differently. This case is also described. FIFO_FULL DATA_RDY FIFO_OVR The DATA_RDY bit is set when new acceleration data is available to the interface. It clears on a read of the status register. It is not set again until acceleration data that is newer than the status register read is available. The FIFO_OVR bit is set when the FIFO is so far overrange that data is lost. The specified size of the FIFO is 96 locations. There is an additional three location buffer to compensate for delays in the synchronization of the clock domains. It is only when there is an attempt to write past this 99 location limit that FIFO_OVR is set. Special logic on the clear of the DATA_RDY bit covers the corner case where new data arrives during the read of the status register. In this case, the data ready condition may be missed completely. This logic results in a delay of the clearing of DATA_RDY of up to four 512 kHz cycles. DRDY PIN DATA is not a status register bit; it instead behaves similar to an unmaskable interrupt. DRDY is set when new acceleration data is available to the interface. It clears on a read of the FIFO, on a read of XDATA, YDATA, or ZDATA, or by an autoclear function that occurs approximately halfway between output acceleration data sets. DRDY is always active high. The INT_POL bit does not affect DRDY. In EXT_SYNC modes, the first few DRDY pulses after initial synchronization can be lost or corrupted. The length of this potential corruption is less than the group delay. The FIFO_FULL bit is set when the entries in the FIFO are equal to the setting of the FIFO_SAMPLES bits. It clears as follows: If the entries in the FIFO fall below the FIFO_SAMPLES, which is only the case if sufficient data is read from the FIFO. On a read of the status register, but only if the entries in the FIFO are less than the FIFO_SAMPLES bits. A read of the status register clears FIFO_OVR. It is not set again until data is lost subsequent to this data register read. ACTIVITY The activity bit (Register 0x04, Bit 3) is set when the measured acceleration on any axis is above the ACT_THRESH bits for ACT_COUNT consecutive measurements. An over threshold condition can shift from one axis to another on successive measurements and is still counted toward the consecutive ACT_COUNT count. A read of the status register clears the activity bit (Register 0x04, Bit 3), but it sets again at the end of the next measurement if the activity bit (Register 0x04, Bit 3) conditions are still satisfied. NVM_BUSY The NVM_BUSY bit indicates that the nonvolatile memory (NVM) controller is busy, and it cannot be accessed to read, write, or generate an interrupt. A status register read that occurs after the NVM controller is no longer busy clears NVM_BUSY. Rev. A | Page 28 of 42 Data Sheet ADXL354/ADXL355 EXTERNAL SYNCHRONIZATION AND INTERPOLATION There are three possible synchronization options for the ADXL355, shown in Figure 72 to Figure 74. For clarity, the clock frequencies and delays are drawn to scale. The labels in Figure 72 to Figure 74 are defined as follows: Internal ODR is the alignment of the decimated output data based on the internal clock. ADC clock shows the internal master clock rate DRDY is an output indicator signaling a sample is ready. EXT_SYNC = 01--External Sync and External Clock The three modes are include as follows: The advantage of this mode is that data is available at a user defined sample rate and is asynchronous to the internal oscillator. The disadvantage of this mode is that the group delay is increased, and there is increased attenuation at the band edge. Additionally, because there is a limit to the time resolution, there is some distortion related to the mismatch of the external sync relative to the internal oscillator. This mismatch degrades spectral performance. The group delay is based on the decimation setting and interpolation setting (see Table 11). Table 13 shows the delay between the SYNC signal (input) to DRDY (output). No external synchronization (internal clocks used) Synchronization with interpolation filter enabled Sync with an external sync and clock signals, no interpolation filter EXT_SYNC = 00--No External Sync or Interpolation For this case, an internal clock that serves as the synchronization master generates the data. No external signals are required, and this is used commonly when the external processor retrieves data from the device asynchronously and absolute synchronization to an external source is not required. Use Register 0x28 to program the ODR. The device outputs a DRDY (active high) to signal that a new sample is available, and data is retrieved from the real-time registers or the FIFO. The group delay is based on the decimation setting as shown in Table 9. In this case, an external source provides an external clock at a frequency of 4 x 64 x ODR. The external clock becomes the master clock source for the device. In addition, an external synchronization signal is needed to align the decimation filter output to a specific clock edge, which provides full external synchronization and is commonly used when a fixed external clock captures and processes data, and asynchronous clock(s) are not allowed. When using multiple sensors, synchronization with an external master clock is beneficial and requires time alignment. When configured for EXT_SYNC = 01 with an ODR of 4 kHz, the user must supply an external clock at 1.024 MHz (64 x 4 x 4 kHz) on the INT2 pin (Pin 13), and an external synchronization on DRDY pin (Pin 14), as shown in Table 12. Special restrictions when using this mode include the following: EXT_SYNC = 10--External Sync with Interpolation In this case, the internal clock generates data; however, an interpolation filter provides additional time resolution of 64 times the programmed ODR. Synchronization using interpolation filters and an external ODR clock is commonly used when the external processor can provide a synchronization signal (which is asynchronous to the internal clock) at the desired ODR. Synchronization with the interpolation filter enabled (EXT_SYNC = 10) allows the nonsynchronous external clock to output data most closely associated with the external clock rising edge. The interpolation filter provides a frequency resolution related to ODR (see Table 11). An external clock (EXT_CLK) must be provided as well as an external sync. The frequency of EXT_CLK must be exactly 4 x 64 x ODR. The width of sync must be a minimum of four EXT_CLK periods. The phase of sync must meet an approximate 25 ns setup time to the EXT_CLK rising edge. When using the EXT_SYNC mode and without providing sync, the device runs on its own synchronization. Similarly, after synchronization, the device continues to run synchronized to the last sync pulse it received, which means that EXT_SYNC = 01 mode can be used with only a single synchronization pulse. The interpolation filter provides a frequency resolution related to the ODR (see Table 11). In this case, the data provided corresponds to the external signal, which can be greater than the set ODR, but the output pass band remains the same it was prior to the interpolation filter. Table 12. Multiplexing of INT2 and DRDY EXT_CLK 0 0 1 1 0 0 Register or Bit Fields EXT_SYNC[1:0] INT_MAP[7:4] 00 0000 00 Not 0000 00 0000 00 Not 00002 01 0000 011 Not 0000 INT2 (Pin 13) Low INT2 EXT_CLK EXT_CLK DRDY INT2 Pins DRDY (Pin 14) DRDY DRDY DRDY DRDY SYNC SYNC Rev. A | Page 29 of 42 Comments Synchronization is to the internal clocks, and there is no external clock synchronization. These options reset the digital filters on every synchronization pulse and are not recommended. ADXL354/ADXL355 Data Sheet EXT_CLK 1 1 Register or Bit Fields EXT_SYNC[1:0] INT_MAP[7:4] 011 0000 011 Not 00002 INT2 (Pin 13) EXT_CLK EXT_CLK 0 0 1 1 10 101 101 101 DRDY INT2 EXT_CLK EXT_CLK 1 2 0000 Not 0000 0000 Not 0000 Pins DRDY (Pin 14) SYNC SYNC SYNC SYNC SYNC SYNC Comments External synchronization, no interpolation filter, and DRDY (active high) signals that data is ready. Data represents a sample point group delay earlier in time. External synchronization, interpolation filter, and DRDY (active high) signals that data is ready. Data sample group delay earlier in time. No DRDY. No INT2, even though it is enabled. GROUP DELAY (FIXED RELATIVE TO DRDY) SAMPLE POINT INTERNAL ODR 14205-036 ADC MOD. CLK. 64x ODR DRDY Figure 72. External Synchronization Option--EXT_SYNC = 00, Internal Sync SAMPLE POINT GROUP DELAY (FIXED RELATIVE TO SYNC) INTERFACE SYNCHRONIZATION DELAY INTERNAL ODR 14205-037 INTERPOLATOR 64x ODR SYNC 110% ODR DRDY Figure 73. External Synchronization Option--EXT_SYNC = 10, External Sync, External Clock, Interpolation Filter SAMPLE POINT GROUP DELAY (FIXED RELATIVE TO SYNC) INTERNAL ODR EXT_CLK (4 x 64) x SYNC SYNCHRONIZE 14205-038 SYNC LOST SAMPLE DRDY Figure 74. External Synchronization Option--EXT_SYNC = 01, External Sync, No Interpolation Filter Table 13. EXT_SYNC = 10, DRDY Delay ODR_LPF 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 0x9 0x10 Delay (OSC Cycles) 8 10 14 22 38 70 134 262 1031 2054 4102 Rev. A | Page 30 of 42 Data Sheet ADXL354/ADXL355 ADXL355 REGISTER MAP Note that while configuring the ADXL355 in an application, all configuration registers must be programmed before enabling measurement mode in the POWER_CTL register. When the ADXL355 is in measurement mode, only the following configurations can change: the HPF_CORNER bits in the filter register, the INT_MAP register, the ST1 and ST2 bits in the SELF_TEST register, and the reset register. Table 14. ADXL355 Register Map Hex. Addr. Register Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset R/W 0x00 DEVID_AD DEVID_AD 0xAD R 0x01 DEVID_MST DEVID_MST 0x1D R 0x02 PARTID PARTID 0xED R 0x03 REVID REVID 0x01 R 0x04 Status FIFO_FULL DATA_RDY 0x00 R 0x05 FIFO_ENTRIES 0x00 R 0x06 TEMP2 0x00 R 0x07 TEMP1 Temperature, Bits[7:0] 0x00 R 0x08 XDATA3 XDATA, Bits[19:12] 0x00 R 0x09 XDATA2 XDATA, Bits[11:4] 0x00 R 0x0A XDATA1 0x00 R 0x0B YDATA3 YDATA, Bits[19:12] 0x00 R 0x0C YDATA2 YDATA, Bits[11:4] 0x00 R 0x0D YDATA1 0x00 R 0x0E ZDATA3 ZDATA, Bits[19:12] 0x00 R 0x0F ZDATA2 ZDATA, Bits[11:4] 0x00 R 0x10 ZDATA1 0x00 R 0x11 FIFO_DATA FIFO_DATA 0x00 R 0x1E OFFSET_X_H OFFSET_X, Bits[15:8] 0x00 R/W 0x1F OFFSET_X_L OFFSET_X, Bits[7:0] 0x00 R/W 0x20 OFFSET_Y_H OFFSET_Y, Bits[15:8] 0x00 R/W 0x21 OFFSET_Y_L OFFSET_Y, Bits[7:0] 0x00 R/W 0x22 OFFSET_Z_H OFFSET_Z, Bits[15:8] 0x00 R/W 0x23 OFFSET_Z_L OFFSET_Z, Bits[7:0] 0x00 R/W 0x24 ACT_EN 0x00 R/W 0x25 ACT_THRESH_H ACT_THRESH, Bits[15:8] 0x00 R/W 0x26 ACT_THRESH_L ACT_THRESH, Bits[7:0] 0x00 R/W 0x27 ACT_COUNT ACT_COUNT 0x01 R/W 0x28 Filter Reserved 0x00 R/W 0x29 FIFO_SAMPLES Reserved 0x60 R/W 0x2A INT_MAP ACT_EN2 OVR_EN2 FULL_EN2 RDY_EN2 0x00 R/W 0x2B Sync 0x00 R/W 0x2C Range 0x2D POWER_CTL 0x2E SELF_TEST 0x2F Reset Reserved NVM_BUSY Activity Reserved FIFO_OVR FIFO_ENTRIES Reserved Temperature, Bits[11:8] XDATA, Bits[3:0] Reserved YDATA, Bits[3:0] Reserved ZDATA, Bits[3:0] Reserved Reserved ACT_Z HPF_CORNER ACT_X ODR_LPF FIFO_SAMPLES ACT_EN1 OVR_EN1 Reserved I2C_HS ACT_Y INT_POL FULL_EN1 EXT_CLK EXT_SYNC Reserved Reserved RDY_EN1 Range DRDY_OFF TEMP_OFF STANDBY Reserved ST2 Reset Rev. A | Page 31 of 42 ST1 0x81 R/W 0x01 R/W 0x00 R/W 0x00 W ADXL354/ADXL355 Data Sheet REGISTER DEFINITIONS This section describes the functions of the ADXL355 registers. The ADXL355 powers up with the default register values, as shown in the Reset column of Table 14. ANALOG DEVICES ID REGISTER This register contains the Analog Devices ID, 0xAD. Address: 0x00, Reset: 0xAD, Name: DEVID_AD Table 15. Bit Descriptions for DEVID_AD Bits [7:0] Bit Name DEVID_AD Settings Description Analog Devices ID Reset 0xAD Access R ANALOG DEVICES MEMS ID REGISTER This register contains the Analog Devices MEMS ID, 0x1D. Address: 0x01, Reset: 0x1D, Name: DEVID_MST Table 16. Bit Descriptions for DEVID_MST Bits [7:0] Bit Name DEVID_MST Settings Description Analog Devices MEMS ID Reset 0x1D Access R DEVICE ID REGISTER This register contains the device ID, 0xED (355 octal). Address: 0x02, Reset: 0xED, Name: PARTID Table 17. Bit Descriptions for PARTID Bits [7:0] Bit Name PARTID Settings Description Device ID (355 octal) Reset 0xED Access R PRODUCT REVISION ID REGISTER This register contains the product revision ID, beginning with 0x00 and incrementing for each subsequent revision. Address: 0x03, Reset: 0x00, Name: REVID Table 18. Bit Descriptions for REVID Bits [7:0] Bit Name REVID Settings Description Mask revision Reset 0x01 Access R STATUS REGISTER This register includes bits that describe the various conditions of the ADXL355. Address: 0x04, Reset: 0x00, Name: STATUS Table 19. Bit Descriptions for STATUS Bits [7:5] 4 3 2 1 0 Bit Name Reserved NVM_BUSY Activity FIFO_OVR FIFO_FULL DATA_RDY Settings Description Reserved. NVM controller is busy with either refresh, programming, or built-in, self test (BIST). Activity, as defined in the THRESH_ACT and COUNT_ACT registers, is detected. FIFO has overrun, and the oldest data is lost. FIFO watermark is reached. A complete x-axis, y-axis, and z-axis measurement was made and results can be read. Rev. A | Page 32 of 42 Reset 0x0 0x0 0x0 0x0 0x0 0x0 Access R R R R R R Data Sheet ADXL354/ADXL355 FIFO ENTRIES REGISTER This register indicates the number of valid data samples present in the FIFO buffer. This number ranges from 0 to 96. Address: 0x05, Reset: 0x00, Name: FIFO_ENTRIES Table 20. Bit Descriptions for FIFO_ENTRIES Bits 7 Bit Name Reserved [6:0] FIFO_ENTRIES Settings Description Reserved Reset 0x0 Access R Number of data samples stored in the FIFO 0x0 R TEMPERATURE DATA REGISTERS These two registers contain the uncalibrated temperature data. The nominal intercept is 1852 LSB at 25C and the nominal slope is -9.05 LSB/C. TEMP2 contains the four most significant bits, and TEMP1 contains the eight least significant bits of the 12-bit value. Address: 0x06, Reset: 0x00, Name: TEMP2 Table 21. Bit Descriptions for TEMP2 Bits [7:4] [3:0] Bit Name Reserved Temperature, Bits[11:8] Settings Description Reserved. Uncalibrated temperature data Reset Access 0x0 R Reset 0x0 Access R Address: 0x07, Reset: 0x00, Name: TEMP1 Table 22. Bit Descriptions for TEMP1 Bits [7:0] Bit Name Temperature, Bits[7:0] Settings Description Uncalibrated temperature data X-AXIS DATA REGISTERS These three registers contain the x-axis acceleration data. Data is left justified and formatted as twos complement. Address: 0x08, Reset: 0x00, Name: XDATA3 Table 23. Bit Descriptions for XDATA3 Bits [7:0] Bit Name XDATA, Bits[19:12] Settings Description X-axis data Reset 0x0 Access R Reset 0x0 Access R Reset 0x0 0x0 Access R R Address: 0x09, Reset: 0x00, Name: XDATA2 Table 24. Bit Descriptions for XDATA2 Bits [7:0] Bit Name XDATA, Bits[11:4] Settings Description X-axis data Address: 0x0A, Reset: 0x00, Name: XDATA1 Table 25. Bit Descriptions for XDATA1 Bits [7:4] [3:0] Bit Name XDATA, Bits[3:0] Reserved Settings Description X-axis data Reserved Rev. A | Page 33 of 42 ADXL354/ADXL355 Data Sheet Y-AXIS DATA REGISTERS These three registers contain the y-axis acceleration data. Data is left justified and formatted as twos complement. Address: 0x0B, Reset: 0x00, Name: YDATA3 Table 26. Bit Descriptions for YDATA3 Bits [7:0] Bit Name YDATA, Bits[19:12] Settings Description Y-axis data Reset 0x0 Access R Reset 0x0 Access R Reset 0x0 0x0 Access R R Address: 0x0C, Reset: 0x00, Name: YDATA2 Table 27. Bit Descriptions for YDATA2 Bits [7:0] Bit Name YDATA, Bits[11:4] Settings Description Y-axis data Address: 0x0D, Reset: 0x00, Name: YDATA1 Table 28. Bit Descriptions for YDATA1 Bits [7:4] [3:0] Bit Name YDATA, Bits[3:0] Reserved Settings Description Y-axis data Reserved Z-AXIS DATA REGISTERS These three registers contain the z-axis acceleration data. Data is left justified and formatted as twos complement. Address: 0x0E, Reset: 0x00, Name: ZDATA3 Table 29. Bit Descriptions for ZDATA3 Bits [7:0] Bit Name ZDATA, Bits[19:12] Settings Description Z-axis data Reset 0x0 Access R Reset 0x0 Access R Address: 0x0F, Reset: 0x00, Name: ZDATA2 Table 30. Bit Descriptions for ZDATA2 Bits [7:0] Bit Name ZDATA, Bits[11:4] Settings Description Z-axis data Address: 0x10, Reset: 0x00, Name: ZDATA1 Table 31. Bit Descriptions for ZDATA1 Bits [7:4] [3:0] Bit Name ZDATA, Bits[3:0] Reserved Settings Description Z-axis data Reserved Rev. A | Page 34 of 42 Reset 0x0 0x0 Access R R Data Sheet ADXL354/ADXL355 FIFO ACCESS REGISTER Address: 0x11, Reset: 0x00, Name: FIFO_DATA Read this register to access data stored in the FIFO. Table 32. Bit Descriptions for FIFO_DATA Bits [7:0] Bit Name FIFO_DATA Settings Description FIFO data is formatted to 24 bits, 3 bytes, most significant byte first. A read to this address pops an effective three equal byte words of axis data from the FIFO. Two subsequent reads or a multibyte read completes the transaction of this data onto the interface. Continued reading or a sustained multibyte read of this field continues to pop the FIFO every third byte. Multibyte reads to this address do not increment the address pointer. If this address is read due to an autoincrement from the previous address, it does not pop the FIFO. Instead, it returns zeros and increments on to the next address. Reset 0x0 Access R Reset 0x0 Access R/W Reset 0x0 Access R/W Reset 0x0 Access R/W Reset 0x0 Access R/W X-AXIS OFFSET TRIM REGISTERS Address: 0x1E, Reset: 0x00, Name: OFFSET_X_H Table 33. Bit Descriptions for OFFSET_X_H Bits [7:0] Bit Name OFFSET_X, Bits[15:8] Settings Description Offset added to x-axis data after all other signal processing. Data is in twos complement format. The significance of OFFSET_X[15:0] matches the significance of XDATA[19:4]. Address: 0x1F, Reset: 0x00, Name: OFFSET_X_L Table 34. Bit Descriptions for OFFSET_X_L Bits [7:0] Bit Name OFFSET_X, Bits[7:0] Settings Description Offset added to x-axis data after all other signal processing. Data is in twos complement format. The significance of OFFSET_X[15:0] matches the significance of XDATA[19:4]. Y-AXIS OFFSET TRIM REGISTERS Address: 0x20, Reset: 0x00, Name: OFFSET_Y_H Table 35. Bit Descriptions for OFFSET_Y_H Bits [7:0] Bit Name OFFSET_Y, Bits[15:8] Settings Description Offset added to y-axis data after all other signal processing. Data is in twos complement format. The significance of OFFSET_Y[15:0] matches the significance of YDATA[19:4]. Address: 0x21, Reset: 0x00, Name: OFFSET_Y_L Table 36. Bit Descriptions for OFFSET_Y_L Bits [7:0] Bit Name OFFSET_Y, Bits[7:0] Settings Description Offset added to y-axis data after all other signal processing. Data is in twos complement format. The significance of OFFSET_Y[15:0] matches the significance of YDATA[19:4]. Rev. A | Page 35 of 42 ADXL354/ADXL355 Data Sheet Z-AXIS OFFSET TRIM REGISTERS Address: 0x22, Reset: 0x00, Name: OFFSET_Z_H Table 37. Bit Descriptions for OFFSET_Z_H Bits [7:0] Bit Name OFFSET_Z, Bits[15:8] Settings Description Offset added to z-axis data after all other signal processing. Data is in twos complement format. The significance of OFFSET_Z[15:0] matches the significance of ZDATA[19:4]. Reset 0x0 Access R/W Reset 0x0 Access R/W Address: 0x23, Reset: 0x00, Name: OFFSET_Z_L Table 38. Bit Descriptions for OFFSET_Z_L Bits [7:0] Bit Name OFFSET_Z, Bits[7:0] Settings Description Offset added to z-axis data after all other signal processing. Data is in twos complement format. The significance of OFFSET_Z[15:0] matches the significance of ZDATA[19:4]. ACTIVITY ENABLE REGISTER Address: 0x24, Reset: 0x00, Name: ACT_EN Table 39. Bit Descriptions for ACT_EN Bits [7:3] 2 1 0 Bit Name Reserved ACT_Z ACT_Y ACT_X Settings Description Reserved. Z-axis data is a component of the activity detection algorithm. Y-axis data is a component of the activity detection algorithm. X-axis data is a component of the activity detection algorithm. Reset 0x0 0x0 0x0 0x0 Access R R/W R/W R/W ACTIVITY THRESHOLD REGISTERS Address: 0x25, Reset: 0x00, Name: ACT_THRESH_H Table 40. Bit Descriptions for ACT_THRESH_H Bits [7:0] Bit Name ACT_THRESH[15:8] Settings Description Threshold for activity detection. Acceleration magnitude must be above ACT_THRESH to trigger the activity counter. ACT_THRESH is an unsigned magnitude. The significance of ACT_TRESH[15:0] matches the significance of XDATA, YDATA, and ZDATA[18:3]. Reset 0x0 Access R/W Reset 0x0 Access R/W Address: 0x26, Reset: 0x00, Name: ACT_THRESH_L Table 41. Bit Descriptions for THRESH_ACT_X_L Bits [7:0] Bit Name ACT_THRESH[7:0] Settings Description Threshold for activity detection. Acceleration magnitude must be above ACT_THRESH to trigger the activity counter. ACT_THRESH is an unsigned magnitude. The significance of ACT_TRESH[15:0] matches the significance of XDATA, YDATA, and ZDATA[18:3]. ACTIVITY COUNT REGISTER Address: 0x27, Reset: 0x01, Name: ACT_COUNT Table 42. Bit Descriptions for ACT_COUNT Bits [7:0] Bit Name ACT_COUNT Settings Description Number of consecutive events above threshold required to detect activity Rev. A | Page 36 of 42 Reset 0x1 Access R/W Data Sheet ADXL354/ADXL355 FILTER SETTINGS REGISTER Address: 0x28, Reset: 0x00, Name: Filter Use this register to specify parameters for the internal high-pass and low-pass filters. Table 43. Bit Descriptions for Filter Bits 7 [6:4] Bit Name Reserved HPF_CORNER Settings 000 001 010 011 100 101 110 [3:0] ODR_LPF 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 Description Reserved -3 dB filter corner for the first-order, high-pass filter relative to the ODR Not applicable, no high-pass filter enabled 247 x 10-3 x ODR 62.084 x 10-3 x ODR 15.545 x 10-3 x ODR 3.862 x 10-3 x ODR 0.954 x 10-3 x ODR 0.238 x 10-3 x ODR ODR and low-pass filter corner 4000 Hz and 1000 Hz 2000 Hz and 500 Hz 1000 Hz and 250 Hz 500 Hz and 125 Hz 250 Hz and 62.5 Hz 125 Hz and 31.25 Hz 62.5 Hz and 15.625 Hz 31.25 Hz and 7.813 Hz 15.625 Hz and 3.906 Hz 7.813 Hz and 1.953 Hz 3.906 Hz and 0.977 Hz Reset 0x0 0x0 Access R R/W 0x0 R/W FIFO SAMPLES REGISTER Address: 0x29, Reset: 0x60, Name: FIFO_SAMPLES Use the FIFO_SAMPLES value to specify the number of samples to store in the FIFO. The default value of this register is 0x60 to avoid triggering the FIFO watermark interrupt. Table 44. Bit Descriptions for FIFO_SAMPLES Bits 7 [6:0] Bit Name Reserved FIFO_SAMPLES Settings Description Reserved. Watermark number of samples stored in the FIFO that triggers a FIFO_FULL condition. Values range from 1 to 96. Reset 0x0 0x60 Access R R/W INTERRUPT PIN (INTx) FUNCTION MAP REGISTER Address: 0x2A, Reset: 0x00, Name: INT_MAP The INT_MAP register configures the interrupt pins. Bits[7:0] select which function(s) generate an interrupt on the INT1 and INT2 pins. Multiple events can be configured. If the corresponding bit is set to 1, the function generates an interrupt on the interrupt pins. Table 45. Bit Descriptions for INT_MAP Bits 7 6 5 4 3 2 1 0 Bit Name ACT_EN2 OVR_EN2 FULL_EN2 RDY_EN2 ACT_EN1 OVR_EN1 FULL_EN1 RDY_EN1 Settings Description Activity interrupt enable on INT2 FIFO_OVR interrupt enable on INT2 FIFO_FULL interrupt enable on INT2 DATA_RDY interrupt enable on INT2 Activity interrupt enable on INT1 FIFO_OVR interrupt enable on INT1 FIFO_FULL interrupt enable on INT1 DATA_RDY interrupt enable on INT1 Rev. A | Page 37 of 42 Reset 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 Access R/W R/W R/W R/W R/W R/W R/W R/W ADXL354/ADXL355 Data Sheet DATA SYNCHRONIZATION Address: 0x2B, Reset: 0x00, Name: Sync Use this register to control the external timing triggers. Table 46. Bit Descriptions for Sync Bits [7:3] 2 [1:0] Bit Name Reserved EXT_CLK EXT_SYNC Settings 00 01 10 11 Description Reserved. Enable external clock. Enable external sync control. Internal sync. External sync, no interpolation filter. After synchronization, and for EXT_SYNC within specification, DATA_RDY occurs on EXT_SYNC. External sync, interpolation filter, next available data indicated by DATA_RDY 14 to 8204 oscillator cycles later (longer delay for higher ODR_LPF setting), data represents a sample point group delay earlier in time. Reserved. Reset 0x0 0x0 0x0 Access R R/W R/W I2C SPEED, INTERRUPT POLARITY, AND RANGE REGISTER Address: 0x2C, Reset: 0x81, Name: Range Table 47. Bit Descriptions for Range Bits 7 Bit Name I2C_HS 6 INT_POL Settings 0 1 [5:2] [1:0] Reserved Range 01 10 11 Description I2C speed. 1 = high speed mode. 0 = fast mode. Interrupt polarity. INT1 and INT2 are active low. INT1 and INT2 are active high. Reserved. Range. 2 g. 4 g. 8 g. Reset 0x1 Access R/W 0x0 R/W 0x0 0x1 R R/W POWER CONTROL REGISTER Address: 0x2D, Reset: 0x01, Name: POWER_CTL Table 48. Bit Descriptions for POWER_CTL Bits [7:3] 2 1 Bit Name Reserved DRDY_OFF TEMP_OFF 0 STANDBY Settings 1 0 Description Reserved. Set to 1 to force the DRDY output to 0 in modes where it is normally signal data ready. Set to 1 to disable temperature processing. Temperature processing is also disabled when STANDBY = 1. Standby or measurement mode. Standby mode. In standby mode, the device is in a low power state, and the temperature and acceleration datapaths are not operating. In addition, digital functions, including FIFO pointers, reset. Changes to the configuration setting of the device must be made when STANDBY = 1. An exception is a high-pass filter that can be changed when the device is operating. Measurement mode. Rev. A | Page 38 of 42 Reset 0x0 0x0 0x0 Access R R/W R/W 0x1 R/W Data Sheet ADXL354/ADXL355 SELF TEST REGISTER Address: 0x2E, Reset: 0x00, Name: SELF_TEST Refer to the Self Test section for more information on the operation of the self test feature. Table 49. Bit Descriptions for SELF_TEST Bits [7:2] 1 0 Bit Name Reserved ST2 ST1 Settings Description Reserved. Set to 1 to enable self test force Set to 1 to enable self test mode Reset 0x0 0x0 0x0 Access R R/W R/W RESET REGISTER Address: 0x2F, Reset: 0x00, Name: Reset Table 50. Bit Descriptions for Reset Bits [7:0] Bit Name Reset Settings Description Write Code 0x52 to resets the device, similar to a power-on reset (POR) Rev. A | Page 39 of 42 Reset 0x0 Access W ADXL354/ADXL355 Data Sheet RECOMMENDED SOLDERING PROFILE Figure 75 and Table 51 provide details about the recommended soldering profile. CRITICAL ZONE TL TO TP tP TP tL TSMAX TSMIN tS RAMP-DOWN PREHEAT t25C TO PEAK TIME 14205-039 TEMPERATURE RAMP-UP TL Figure 75. Recommended Soldering Profile Table 51. Recommended Soldering Profile Profile Feature Average Ramp Rate from Liquid Temperature (TL) to Peak Temperature (TP) Preheat Minimum Temperature (TSMIN) Maximum Temperature (TSMAX) Time from TSMIN to TSMAX (tS) TSMAX to TL Ramp-Up Rate Liquid Temperature (TL) Time Maintained Above TL (tL) Peak Temperature (TP) Time of Actual TP - 5C (tP) Ramp-Down Rate Time from 25C to Peak Temperature (t25C TO PEAK) Rev. A | Page 40 of 42 Sn63/Pb37 3C/sec maximum Condition Pb-Free 3C/sec maximum 100C 150C 60 sec to 120 sec 3C/sec maximum 183C 60 sec to 150 sec 240C + 0C/-5C 10 sec to 30 sec 6C/sec maximum 6 minutes maximum 150C 200C 60 sec to 180 sec 3C/sec maximum 217C 60 sec to 150 sec 260C + 0C/-5C 20 sec to 40 sec 6C/sec maximum 8 minutes maximum Data Sheet ADXL354/ADXL355 PCB FOOTPRINT PATTERN Figure 76 shows the PCB footprint pattern and dimensions in millimeters. 3.22mm 0.68mm 0.70mm 3.80mm 14 PLCS 1.8mm x 0.68mm 3.80mm Figure 76. PCB Footprint Pattern and Dimensions in Millimeters Rev. A | Page 41 of 42 14205-040 4.5mm 0.70mm ADXL354/ADXL355 Data Sheet PACKAGING AND ORDERING INFORMATION OUTLINE DIMENSIONS DETAIL A 6.25 6.00 SQ 5.85 0.80 BSC 2.25 2.05 1.85 1.674 BSC 0.510 REF 0.30 SQ 12 (PIN 1 INDEX) 14 11 1 DETAIL A 5.60 SQ R 0.103 (14 PLCS) 3.81 REF 0.508 BSC 4 8 7 TOP VIEW 0.10 BSC R 0.203 (14 PLCS) 0.15 BSC 5 BOTTOM VIEW SIDE VIEW 2.20 REF 2.54 REF 0.914 BSC 05-27-2016-B PKG-004554 R 0.25 (4 PLCS) Figure 77. 14-Terminal Ceramic Leadless Chip Carrier [LCC] (E-14-1) Dimensions shown in millimeters BRANDING INFORMATION NO BRAND ON THIS LINE PART NUMBER PIN ONE LOCATOR, NO OTHER BRAND ON THIS LINE ADXL354B, ADXL354C, OR ADXL355B SIX DIGIT LOT NUMBER 6 DIGIT LOT NUMBER 14205-078 TWO DIGIT YEAR, TWO DIGIT WEEK ID #YYWW Figure 78. Branding Information ORDERING GUIDE Model1 ADXL354BEZ ADXL354BEZ-RL ADXL354BEZ-RL7 ADXL354CEZ ADXL354CEZ-RL ADXL354CEZ-RL7 ADXL355BEZ Output Mode Analog Analog Analog Analog Analog Analog Digital ADXL355BEZ-RL Digital ADXL355BEZ-RL7 Digital Measurement Range (g) 2, 4 2, 4 2, 4 2, 8 2, 8 2, 8 2.048, 4.096, 8.192 2.048, 4.096, 8.192 2.048, 4.096, 8.192 Specified Voltage (V) 3.3 3.3 3.3 3.3 3.3 3.3 3.3 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Package Description 14-Terminal LCC 14-Terminal LCC 14-Terminal LCC 14-Terminal LCC 14-Terminal LCC 14-Terminal LCC 14-Terminal LCC Package Option E-14-1 E-14-1 E-14-1 E-14-1 E-14-1 E-14-1 E-14-1 3.3 -40C to +125C 14-Terminal LCC E-14-1 3.3 -40C to +125C 14-Terminal LCC E-14-1 EVAL-ADXL354BZ EVAL-ADXL354CZ EVAL-ADXL355Z 1 Evaluation Board for ADXL354BEZ Evaluation Board for ADXL354CEZ Evaluation Board for ADXL355BEZ Z = RoHS-Compliant Part. (c)2016-2018 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D14205-0-4/18(A) Rev. A | Page 42 of 42