H_S-1W & G_S-1W Series 1W, FIXED INPUT, ISOLATED & UNREGULATED SINGLE / DUAL OUTPUT FEATURES SIP package 6000VDC isolation Operating temperature range: -40~+105 Efficiency up to 80% Internal SMD construction No external component required Industry standard pinout Patent Protected RoHS APPLICATIONS PART NUMBER SYSTEM The H_S-1W & G_S-1W Series are designed for application where isolated output is required from a distributed power system. These products apply to where: 1) Input voltage rang :10%Vin; 2) 6000VDC input and output isolation; 3) Where do not has high requirement of line regulation and the ripple & noise of the output voltage; Such as: digital circuit, low frequency analog circuit, and relay drive circuit. G0505S-1W Rated Power Package Output Voltage Input Voltage Product Series SELECTION GUIDE Model H0503S-1W H0505S-1W H0509S-1W H0512S-1W H0515S-1W H0524S-1W G0505S-1W G0507S-1W G0509S-1W G0512S-1W G0515S-1W H1205S-1W H1207S-1W H1209S-1W H1212S-1W H1215S-1W G1205S-1W G1207S-1W G1209S-1W G1212S-1W G1215S-1W H1505S-1W G1505S-1W G1515S-1W H2403S-1W H2405S-1W H2412S-1W H2415S-1W G2412S-1W Input Voltage(VDC) Nominal (Range) 5 (4.5-5.5) 12 (10.8-13.2) 15 (13.5-16.5) 24 (21.6- 26.4 Output Current (mA) Output Voltage (VDC) Max. Min. 3.3 5 9 12 15 24 5 7.2 9 12 15 5 7.2 9 12 15 5 7.2 9 12 15 5 5 15 3.3 5 12 15 12 303 200 111 84 67 42 100 70 56 42 33 200 139 111 84 67 100 70 56 42 33 200 100 33 303 200 84 67 42 30 20 12 9 7 4 10 7 6 5 4 20 14 12 9 7 10 7 6 5 4 20 10 4 30 20 9 7 5 Input Current (mA,Typ.) Reflected Max. Ripple Efficiency Capacitive Current (%, Typ.) @Max. Load @No Load (mA,Typ.) Load(F) 278 72 256 78 253 79 220 253 79 253 79 250 30 15 80 256 78 256 78 253 100 79 253 79 253 79 104 80 104 80 102 220 82 103 81 102 82 20 5 104 80 104 80 102 100 82 103 81 102 82 82 220 80 82 15 5 80 100 81 81 58 72 52 80 220 52 10 5 80 52 80 52 100 80 Approval -UL UL UL UL ------UL -UL UL UL -------------- Note: *The capacitive loads of positive and negative outputs are identical. The copyright and authority for the interpretation of the products are reserved by MORNSUN H_S-1W & G_S-1W 2015.04.27-B/4 Page 1 of 5 INPUT SPECIFICATIONS Item Input Surge Voltage (1 sec. max.) Test Conditions Min. Typ. Max. 5VDC Input -0.7 -- 9 12VDC Input -0.7 -- 18 15VDC Input -0.7 -- 21 24VDC Input -0.7 -- 30 Input Filter Unit VDC Capacitor OUTPUT SPECIFICATIONS Item Test Conditions Min. Output Voltage Accuracy Line Regulation Max. Unit See tolerance envelope curve For Vin change of 1% Load Regulation 10% to 100% load Temperature coefficient Ripple & Noise* Typ. -- -- 1.2 3.3VDC output -- 15 -- 5VDC output -- 12 -- 7.2&9VDC output -- 8 -- 12VDC output -- 7 -- 15VDC output -- 6 -- 24VDC output -- 5 -- 100% load 20MHz Bandwidth -- % -- -- 0.03 Output Voltage 12VDC -- 100 -- Output Voltage :15VDC, 24VDC -- 150 -- Short Circuit Protection %/C mVp-p Continuous, automatic recovery Note:* Ripple and noise tested with "parallel cable" method. See detailed operation instructions at DC-DC Application Notes. COMMON SPECIFICATIONS Item Test Conditions Min. Typ. Max. Unit Isolation Voltage Input-Output, tested for 1 minute and leakage current less than 1 mA 6000 -- -- VDC Isolation Resistance Input-Output, test at 500VDC 1000 -- -- M Isolation Capacitance Input-Output, 100KHz/0.1V -- 10 -- pF Switching Frequency Full load, nominal input -- 50 -- KHz MTBF MIL-HDBK-217F@25 3500 -- -- K hours Case Material Plastic (UL94-V0) Weight -- 4.2 -- g ENVIRONMENTAL SPECIFICATIONS Item Test Conditions Storage Humidity Non condensing Operating Temperature Power derating (100, see Figure 2) Storage Temperature Min. Typ. Max. Unit % -- -- 95 -40 -- 105 -55 -- 125 Temperature rise Ta=25C,100% Load -- 25 -- Lead Temperature 1.5mm from case for 10 seconds -- -- 300 Cooling C Free air convection EMC SPECIFICATIONS EMI EMS CE CISPR22/EN55022 CLASS BTypical Recommended Circuit Refer to Figure1 RE CISPR22/EN55022 CLASS BTypical Recommended Circuit Refer to Figure1 ESD IEC/EN61000-4-2 Contact 8KV The copyright and authority for the interpretation of the products are reserved by MORNSUN perf. Criteria B H_S-1W & G_S-1W 2015.04.27-B/4 Page 2 of 5 EMC RECOMMENDED CIRCUIT Recommended typical circuit parameters: EMI Typical Recommended CircuitCLASS B Input voltage (V) LDM Vin Vin C1 GND C2 +Vo DC/DC GND C3 4.7F /50V C3 Refer to the Cout in Fig.3 LDM 6.8H EMI LOAD 5/12/15/24 C1, C2 -Vo (0V) (Figure1) EMC TEST WAVEFORM (RECOMMENDED CIRCUIT FINGURE 1) H0505S-1W CE(Positive line) H0505S-1W CE(Negative, line) PRODUCT TYPICAL CURVE Other output 3.3VDC /5VDC output Tolerance Envelope Cur ve +10% +5% 0 -5% Max . Ty p . M in. +2.5% -2.5% -7.5% -10% 10% 20% +15% Output Voltage Accuracy Output Voltage Accuracy +15% 40% 80% 60% Output Current Percent (Nominal Input Voltage) Tolerance Envelope Cur ve +10% Max . +5% Ty p . 0 +2.5% M in. -5% -2.5% -7.5% -10% 10% 20% 100% 40% 60% 80% 100% Output Current Percent (Nominal Input Voltage) Output Power Percent(%) Temperature Derating G raph 120 100 80 60 40 Safe Operating Area 20 0 -40 0 40 80 100 105 Ambient Temp.( ) (Figure 2) The copyright and authority for the interpretation of the products are reserved by MORNSUN H_S-1W & G_S-1W 2015.04.27-B/4 Page 3 of 5 DIMENSIONS, RECOMMENDED FOOTPRINT & PACKAGING TEST CONFIGURATIONS Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with an inductor Lin and Capacitor Cin to simulate the source impedance . Oscilloscope Lin Cin Lin(4.7H) Current Probe DC DC Load Cin(220F, ESR < 1.0 at 100 KHz) The copyright and authority for the interpretation of the products are reserved by MORNSUN H_S-1W & G_S-1W 2015.04.27-B/4 Page 4 of 5 DESIGN CONSIDERATIONS 1) Requirement for output load To ensure this module can operate efficiently and reliably, the minimum output load could not be less than 10% of the full load. If the actual output power is very small, please connect a resistor to the output in parallel to increase the load. 2) Overload Protection Under normal operating conditions, the output circuit of these products have not overload protection. The simplest method is to add a breaker circuit in the circuit. 3) Recommended circuit If you want to further decrease the input/output ripple, an capacitor filtering network may be connected to the input and output ends of the DC/DC converter, refer to Figure 3. It should also be noted that the capacitance of the capacitor must be proper. If the capacitance is too large, a startup problem might arise.For ensuring every channel of output can provide a safe and reliable operation , the recommended capacitance of the capacitor refer to Table 1. D u a l O u tp u t L L Vin Cout DC DC Cin L Cout GND Si n g l e O u tp u t L Vin L DC DC Cin +Vo 0V -Vo +Vo Cout GND 0V (Figure 3) Vin (VDC) EXTERNAL CAPACITOR TABLE (Table 1) Cin Single Vout Cout Dual Vout (F) (VDC) (F) (VDC) Cout (F) 5 4.7 3.3 10 -- -- 5 4.7 5 10 5 4.7 12 2.2 9 4.7 9 2.2 15 2.2 12 2.2 12 2.2 24 1 15 1 15 1 It's not recommended to connect any external capacitor in the application field with less than 0.5 watt output. 4) The input and the output of the product are recommended to be connected to ceramic capacitor or electrolytic capacitor. Using tantalum capacitor may cause risk of failure. 5) It is not recommended to increase the output power capability by connecting two or more converters in parallel. The product is not hot-swappable Note: 1. Operation under minimum load will not damage the converter; However, they may not meet all specifications. 2. Max. Capacitive Load is tested at nominal input voltage and full load. 3. Unless otherwise noted, All specifications are measured at Ta=25C, humidity<75%, nominal input voltage and rated output load. 4. In this datasheet, all test methods are based on our corporate standards. 5. All characteristics are for listed models, and non-standard models may perform differently.Please contact our technical support for more detail. 6. Please contact our technical support for any specific requirement. 7. Specifications of this product are subject to changes without prior notice. MORNSUN Science & Technology Co.,Ltd. Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China. Tel: 86-20-38601850 Fax:86-20-38601272 E-mail: info@mornsun.cn Http://www.mornsun-power.com The copyright and authority for the interpretation of the products are reserved by MORNSUN H_S-1W & G_S-1W 2015.04.27-B/4 Page 5 of 5