153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S DESCRIPTION * * * 153.6 MHz SAW bandpass filter with 20 MHz bandwidth. 7 x 5 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 5 deg/div Delay 100 ns/div Center = 153.6 MHz, 15 MHz/div (187.5 kHz incr) S11 (78.6-228.6 MHz) S22 (78.6-228.6 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0154BA03191S Rev B ECN 36650 11-Mar-2010 Page 1 of 3 153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S SPECIFICATION Parameter Center Frequency, FC 1 Minimum Insertion Loss Passband Ripple (143.6 to 163.6 MHz) Group Delay Deviation (143.6 to 153.6 MHz) Phase Ripple (143.6 to 153.6 MHz) Absolute Delay 1 dB bandwidth 2 Relative Attenuation (10 to 105 MHz) 2 Relative Attenuation (200 to 230 MHz) 2 Relative Attenuation (230 to 1000 MHz) 2 Input Return Loss at Fc Output Return Loss at Fc Source and Load Impedance Temperature Coefficient of Frequency Ambient Temperature Notes: Min 20 50 52 40 10 10 - Typ 153.6 8.8 0.4 30 3.5 560 23.4 52 55 60 15 18 50 -86 25 Max 12 1 60 5 - - Units MHz dB dB p-p ns p-p deg p-p ns MHz dB dB dB dB dB ohms ppm/C C 1. Reference frequency. Computed as mean of the 3 dB frequencies. 2. All dB values are referenced to the insertion loss value. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -40 - 85 85 10 Units C C dBm MATCHING CIRCUIT 10 5 Input 50 Single ended Output 50 Single ended All other pads GND Ls1 = 138 nH GND Ls2 = 207 nH Cp1 = 22 pF Cp2 = 15 pF Notes: * Recommend 2% or better tolerance matching components. Typical inductor Q=40. * Optimum values may change depending on board layout. Values shown are intended as a guide only. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0154BA03191S Rev B ECN 36650 11-Mar-2010 Page 2 of 3 153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S PACKAGE OUTLINE SMI BA03191S YYDDD Date Code (YY=year, DDD=day) Pad 1 indicator mark (ESD) Units: mm Tolerances are typically 0.15 mm except where indicated. Pad Configuration: Input: 10 Output: 5 Ground: All other pads SUGGESTED FOORPRINT Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating 2.54 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. (c) 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0154BA03191S Rev B ECN 36650 11-Mar-2010 Page 3 of 3