2552AS–AVR–11/04
Features
High Performance, Low Power AVR® 8-Bit Microcontroller
Advanced RISC Architecture
130 Powerful Instructions – Most Single Clock Cycle Execution
32 x 8 General Purpose Working Registers
Fully Static Operation
Up to 16 MIPS Throughput at 16 MHz
On-Chip 2-cycle Multiplier
Non-volatile Program and Data Memories
In-System Self-Programmable Flash, Endurance: 10,000 Write/Erase Cycles
32K bytes (ATmega329/ATmega3290)
64K bytes (ATmega649/ATmega6490)
Optional Boot Code Section with Independent Lock Bits
In-System Programming by On-chip Boot Program
True Read-While-Write Operation
EEPROM, Endurance: 100,000 Write/Erase Cycles
1K bytes (ATmega329/ATmega3290)
2K bytes (ATmega649/ATmega6490)
Internal SRAM
2K bytes (ATmega329/ATmega3290)
4K bytes (ATmega649/ATmega6490)
Programming Lock for Software Security
JTAG (IEEE std. 1149.1 compliant) Interface
Boundary-scan Capabilities According to the JTAG Standard
Extensive On-chip Debug Support
Programming of Flash, EEPROM, Fuses, and Lock Bits through the JTAG Interface
Peripheral Features
4 x 25 Segment LCD Driver (ATmega329/ATmega649)
4 x 40 Segment LCD Driver (ATmega3290/ATmega6490)
Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode
One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture
Mode
Real Time Counter with Separate Oscillator
Four PWM Channels
8-channel, 10-bit ADC
Programmable Serial USART
Master/Slave SPI Serial Interface
Universal Serial Interface with Start Condition Detector
Programmable Watchdog Timer with Separate On-chip Oscillator
On-chip Analog Comparator
Interrupt and Wake-up on Pin Change
Special Microcontroller Features
Power-on Reset and Programmable Brown-out Detection
Internal Calibrated Oscillator
External and Internal Interrupt Sources
Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and
Standby
I/O and Packages
53/68 Programmable I/O Lines
64-lead TQFP, 64-pad MLF, and 100-lead TQFP
Speed Grade:
ATmega329V/ATmega3290V/ATmega649V/ATmega6490V:
0 - 4 MHz @ 1.8 - 5.5V, 0 - 8 MHz @ 2.7 - 5.5V
ATmega329/3290/649/6490:
0 - 8 MHz @ 2.7 - 5.5V, 0 - 16 MHz @ 4.5 - 5.5V
Temperature range:
-40°C to 85°C Industrial
8-bit
Microcontroller
with In-System
Programmable
Flash
ATmega329/V
ATmega3290/V
ATmega649/V
ATmega6490/V
Preliminary
Summary
Note: This is a summary document. A complete document
is available on our Web site at www.atmel.com.
2ATmega329/3290/649/6490
2552AS–AVR–11/04
Features (Continued)
Ultra-Low Power Consumption
Active Mode:
1 MHz, 1.8V: 350 µA
32 kHz, 1.8V: 20 µA (including Oscillator)
32 kHz, 1.8V: 40 µA (including Oscillator and LCD)
Power-down Mode:
100 nA at 1.8V
Pin Configurations Figure 1. Pinout ATmega3290/6490
(OC2A/PCINT15) PB7
DNC
(T1/SEG33) PG3
(T0/SEG32) PG4
RESET/PG5
VCC
GND
(TOSC2) XTAL2
(TOSC1) XTAL1
DNC
DNC
(PCINT26/SEG31) PJ2
(PCINT27/SEG30) PJ3
(PCINT28/SEG29) PJ4
(PCINT29/SEG28) PJ5
(PCINT30/SEG27) PJ6
DNC
(ICP1/SEG26) PD0
(INT0/SEG25) PD1
(SEG24) PD2
(SEG23) PD3
(SEG22) PD4
(SEG21) PD5
(SEG20) PD6
(SEG19) PD7
AVCC
AGND
AREF
PF0 (ADC0)
PF1 (ADC1)
PF2 (ADC2)
PF3 (ADC3)
PF4 (ADC4/TCK)
PF5 (ADC5/TMS)
PF6 (ADC6/TDO)
PF7 (ADC7/TDI)
DNC
DNC
PH7 (PCINT23/SEG36)
PH6 (PCINT22/SEG37)
PH5 (PCINT21/SEG38)
PH4 (PCINT20/SEG39)
DNC
DNC
GND
VCC
DNC
PA0 (COM0)
PA1 (COM1)
PA2 (COM2)
PA3 (COM3)
PA4 (SEG0)
PA5 (SEG1)
PA6 (SEG2)
PA7 (SEG3)
PG2 (SEG4)
PC7 (SEG5)
PC6 (SEG6)
DNC
PH3 (PCINT19/SEG7)
PH2 (PCINT18/SEG8)
PH1 (PCINT17/SEG9)
PH0 (PCINT16/SEG10)
DNC
DNC
DNC
DNC
PC5 (SEG11)
PC4 (SEG12)
PC3 (SEG13)
PC2 (SEG14)
PC1 (SEG15)
PC0 (SEG16)
PG1 (SEG17)
PG0 (SEG18)
INDEX CORNER
ATmega3290/6490
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
LCDCAP
(RXD/PCINT0) PE0
(TXD/PCINT1) PE0
(XCK/AIN0/PCINT2) PE2
(AIN1/PCINT3) PE3
(USCK/SCL/PCINT4) PE4
(DI/SDA/PCINT5) PE5
(DO/PCINT6) PE6
(CLKO/PCINT7) PE7
VCC
GND
DNC
(PCINT24/SEG35) PJ0
(PCINT25/SEG34) PJ1
DNC
DNC
DNC
DNC
(SS/PCINT8) PB0
(SCK/PCINT9) PB1
(MOSI/PCINT10) PB2
(MISO/PCINT11) PB3
(OC0A/PCINT12) PB4
(OC1A/PCINT13) PB5
(OC1B/PCINT14) PB6
TQFP
3
ATmega329/3290/649/6490
2552AS–AVR–11/04
Figure 2. Pinout ATmega329/649
Note: The large center pad underneath the MLF packages is made of metal and internally con-
nected to GND. It should be soldered or glued to the board to ensure good mechanical
stability. If the center pad is left unconnected, the package might loosen from the board.
Disclaimer Typical values contained in this datasheet are based on simulations and characteriza-
tion of other AVR microcontrollers manufactured on the same process technology. Min
and Max values will be available after the device is characterized.
PC0 (SEG12)
VCC
GND
PF0 (ADC0)
PF7 (ADC7/TDI)
PF1 (ADC1)
PF2 (ADC2)
PF3 (ADC3)
PF4 (ADC4/TCK)
PF5 (ADC5/TMS)
PF6 (ADC6/TDO)
AREF
GND
AVCC
17
61
60
18
59
20
58
19
21
57
22
56
23
55
24
54
25
53
26
52
27
51
29
28
50
49
32
31
30
(RXD/PCINT0) PE0
(TXD/PCINT1) PE1
LCDCAP
(XCK/AIN0/PCINT2) PE2
(AIN1/PCINT3) PE3
(USCK/SCL/PCINT4) PE4
(DI/SDA/PCINT5) PE5
(DO/PCINT6) PE6
(CLKO/PCINT7) PE7
(SCK/PCINT9) PB1
(MOSI/PCINT10) PB2
(MISO/PCINT11) PB3
(OC0A/PCINT12) PB4
(OC2A/PCINT15) PB7
(T1/SEG24) PG3
(OC1B/PCINT14) PB6
(T0/SEG23) PG4
(OC1A/PCINT13) PB5
PC1 (SEG11)
PG0 (SEG14)
(SEG15) PD7
PC2 (SEG10)
PC3 (SEG9)
PC4 (SEG8)
PC5 (SEG7)
PC6 (SEG6)
PC7 (SEG5)
PA7 (SEG3)
PG2 (SEG4)
PA6 (SEG2)
PA5 (SEG1)
PA4 (SEG0)
PA3 (COM3)
PA0 (COM0)
PA1 (COM1)
PA2 (COM2)
PG1 (SEG13)
(SEG16) PD6
(SEG17) PD5
(SEG18) PD4
(SEG19) PD3
(SEG20) PD2
(INT0/SEG21) PD1
(ICP1/SEG22) PD0
(TOSC1) XTAL1
(TOSC2) XTAL2
RESET/PG5
GND
VCC
INDEX CORNER
(SS/PCINT8) PB0
2
3
1
4
5
6
7
8
9
10
11
12
13
14
16
15
64
63
62
47
46
48
45
44
43
42
41
40
39
38
37
36
35
33
34
ATmega329/649
MLF / TQFP
4ATmega329/3290/649/6490
2552AS–AVR–11/04
Overview
The ATmega329/3290/649/6490 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architec-
ture. By executing powerful instructions in a single clock cycle, the ATmega329/3290/649/6490 achieves throughputs
approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.
Block Diagram
Figure 3. Block Diagram
PROGRAM
COUNTER
INTERNAL
OSCILLATOR
WATCHDOG
TIMER
STACK
POINTER
PROGRAM
FLASH
MCU CONTROL
REGISTER
SRAM
GENERAL
PURPOSE
REGISTERS
INSTRUCTION
REGISTER
TIMER/
COUNTERS
INSTRUCTION
DECODER
DATA DIR.
REG. PORTB
DATA DIR.
REG. PORTE
DATA DIR.
REG. PORTA
DATA DIR.
REG. PORTD
DATA REGISTER
PORTB
DATA REGISTER
PORTE
DATA REGISTER
PORTA
DATA REGISTER
PORTD
TIMING AND
CONTROL
OSCILLATOR
INTERRUPT
UNIT
EEPROM
SPI
USART
STATUS
REGISTER
Z
Y
X
ALU
PORTB DRIVERS
PORTE DRIVERS
PORTA DRIVERS
PORTF DRIVERS
PORTD DRIVERS
PORTC DRIVERS
PB0 - PB7PE0 - PE7
PA0 - PA7PF0 - PF7
VCCGND
XTAL1
XTAL2
CONTROL
LINES
+
-
ANALOG
COMPARATOR
PC0 - PC7
8-BIT DATA BUS
RESET
CALIB. OSC
DATA DIR.
REG. PORTC
DATA REGISTER
PORTC
ON-CHIP DEBUG
JTAG TAP
PROGRAMMING
LOGIC
BOUNDARY-
SCAN
DATA DIR.
REG. PORTF
DATA REGISTER
PORTF
ADC
PD0 - PD7
DATA DIR.
REG. PORTG
DATA REG.
PORTG
PORTG DRIVERS
PG0 - PG4
AGND
AREF
AVCC
UNIVERSAL
SERIAL INTERFACE
AVR CPU
LCD
CONTROLLER/
DRIVER
PORTH DRIVERS
PH0 - PH7
DATA DIR.
REG. PORTH
DATA REGISTER
PORTH
PORTJ DRIVERS
PJ0 - PJ6
DATA DIR.
REG. PORTJ
DATA REGISTER
PORTJ
5
ATmega329/3290/649/6490
2552AS–AVR–11/04
The AVR core combines a rich instruction set with 32 general purpose working registers.
All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing
two independent registers to be accessed in one single instruction executed in one clock
cycle. The resulting architecture is more code efficient while achieving throughputs up to
ten times faster than conventional CISC microcontrollers.
The ATmega329/3290/649/6490 provides the following features: 32/64K bytes of In-
System Programmable Flash with Read-While-Write capabilities, 1/2K bytes EEPROM,
2/4K byte SRAM, 53/68 general purpose I/O lines, 32 general purpose working regis-
ters, a JTAG interface for Boundary-scan, On-chip Debugging support and
programming, a complete On-chip LCD controller with internal contrast control, three
flexible Timer/Counters with compare modes, internal and external interrupts, a serial
programmable USART, Universal Serial Interface with Start Condition Detector, an 8-
channel, 10-bit ADC, a programmable Watchdog Timer with internal Oscillator, an SPI
serial port, and five software selectable power saving modes. The Idle mode stops the
CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to con-
tinue functioning. The Power-down mode saves the register contents but freezes the
Oscillator, disabling all other chip functions until the next interrupt or hardware reset. In
Power-save mode, the asynchronous timer and the LCD controller continues to run,
allowing the user to maintain a timer base and operate the LCD display while the rest of
the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O mod-
ules except asynchronous timer, LCD controller and ADC, to minimize switching noise
during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running
while the rest of the device is sleeping. This allows very fast start-up combined with low-
power consumption.
The device is manufactured using Atmel’s high density non-volatile memory technology.
The On-chip In-System re-Programmable (ISP) Flash allows the program memory to be
reprogrammed In-System through an SPI serial interface, by a conventional non-volatile
memory programmer, or by an On-chip Boot program running on the AVR core. The
Boot program can use any interface to download the application program in the Applica-
tion Flash memory. Software in the Boot Flash section will continue to run while the
Application Flash section is updated, providing true Read-While-Write operation. By
combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic
chip, the Atmel ATmega329/3290/649/6490 is a powerful microcontroller that provides a
highly flexible and cost effective solution to many embedded control applications.
The ATmega329/3290/649/6490 AVR is supported with a full suite of program and sys-
tem development tools including: C Compilers, Macro Assemblers, Program
Debugger/Simulators, In-Circuit Emulators, and Evaluation kits.
6ATmega329/3290/649/6490
2552AS–AVR–11/04
Comparison between
ATmega329,
ATmega3290,
ATmega649 and
ATmega6490
The ATmega329, ATmega3290, ATmega649, and ATmega6490 differs only in memory
sizes, pin count and pinout. Table 1 on page 6 summarizes the different configurations
for the four devices.
Pin Descriptions The following section describes the I/O-pin special functions.
VCC Digital supply voltage.
GND Ground.
Port A (PA7..PA0) Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port A output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port A pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port A pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port A also serves the functions of various special features of the
ATmega329/3290/649/6490 as listed on page 59.
Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port B output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port B pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port B has better driving capabilities than the other ports.
Port B also serves the functions of various special features of the
ATmega329/3290/649/6490 as listed on page 60.
Port C (PC7..PC0) Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port C output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port C pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port C also serves the functions of special features of the ATmega329/3290/649/6490
as listed on page 63.
Port D (PD7..PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port D output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port D pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Table 1. Configuration Summary
Device Flash EEPROM RAM
LCD
Segments
General Purpose
I/O Pins
ATmega329 32K bytes 1K bytes 2K bytes 4 x 25 53
ATmega3290 32K bytes 1K bytes 2K bytes 4 x 40 68
ATmega649 64K bytes 2K bytes 4K bytes 4 x 25 53
ATmega6490 64K bytes 2K bytes 4K bytes 4 x 40 68
7
ATmega329/3290/649/6490
2552AS–AVR–11/04
Port D also serves the functions of various special features of the
ATmega329/3290/649/6490 as listed on page 65.
Port E (PE7..PE0) Port E is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port E output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port E pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port E pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port E also serves the functions of various special features of the
ATmega329/3290/649/6490 as listed on page 67.
Port F (PF7..PF0) Port F serves as the analog inputs to the A/D Converter.
Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used.
Port pins can provide internal pull-up resistors (selected for each bit). The Port F output
buffers have symmetrical drive characteristics with both high sink and source capability.
As inputs, Port F pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port F pins are tri-stated when a reset condition becomes
active, even if the clock is not running. If the JTAG interface is enabled, the pull-up resis-
tors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be activated even if a reset
occurs.
Port F also serves the functions of the JTAG interface.
Port G (PG4..PG0) Port G is a 5-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port G output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port G pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port G pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port G also serves the functions of various special features of the
ATmega329/3290/649/6490 as listed on page 67.
Port H (PH7..PH0) Port H is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port H output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port H pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port H pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port H also serves the functions of various special features of the ATmega3290/6490 as
listed on page 67.
Port J (PJ6..PJ0) Port J is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each
bit). The Port J output buffers have symmetrical drive characteristics with both high sink
and source capability. As inputs, Port J pins that are externally pulled low will source
current if the pull-up resistors are activated. The Port J pins are tri-stated when a reset
condition becomes active, even if the clock is not running.
Port J also serves the functions of various special features of the ATmega3290/6490 as
listed on page 67.
RESET Reset input. A low level on this pin for longer than the minimum pulse length will gener-
ate a reset, even if the clock is not running. The minimum pulse length is given in Table
16 on page 39. Shorter pulses are not guaranteed to generate a reset.
XTAL1 Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.
8ATmega329/3290/649/6490
2552AS–AVR–11/04
XTAL2 Output from the inverting Oscillator amplifier.
AVCC AVCC is the supply voltage pin for Port F and the A/D Converter. It should be externally
connected to VCC, even if the ADC is not used. If the ADC is used, it should be con-
nected to VCC through a low-pass filter.
AREF This is the analog reference pin for the A/D Converter.
LCDCAP An external capacitor (typical > 470 nF) must be connected to the LCDCAP pin as
shown in Figure 98. This capacitor acts as a reservoir for LCD power (VLCD). A large
capacitance reduces ripple on VLCD but increases the time until VLCD reaches its target
value.
9
ATmega329/3290/649/6490
2552AS–AVR–11/04
Register Summary Note: Registers with bold type only available in ATmega3290/6490.
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
(0xFF) LCDDR19 SEG339 SEG338 SEG337 SEG336 SEG335 SEG334 SEG333 SEG332 230
(0xFE) LCDDR18 SEG331 SEG330 SEG329 SEG328 SEG327 SEG326 SEG325 SEG324 230
(0xFD) LCDDR17 SEG323 SEG322 SEG321 SEG320 SEG319 SEG318 SEG317 SEG316 230
(0xFC) LCDDR16 SEG315 SEG314 SEG313 SEG312 SEG311 SEG310 SEG309 SEG308 230
(0xFB) LCDDR15 SEG307 SEG306 SEG305 SEG304 SEG303 SEG302 SEG301 SEG300 230
(0xFA) LCDDR14 SEG239 SEG238 SEG237 SEG236 SEG235 SEG234 SEG233 SEG232 230
(0xF9) LCDDR13 SEG231 SEG230 SEG229 SEG228 SEG227 SEG226 SEG225 SEG224 230
(0xF8) LCDDR12 SEG223 SEG222 SEG221 SEG220 SEG219 SEG218 SEG217 SEG216 230
(0xF7) LCDDR11 SEG215 SEG214 SEG213 SEG212 SEG211 SEG210 SEG209 SEG208 230
(0xF6) LCDDR10 SEG207 SEG206 SEG205 SEG204 SEG203 SEG202 SEG201 SEG200 230
(0xF5) LCDDR09 SEG139 SEG138 SEG137 SEG136 SEG135 SEG134 SEG133 SEG132 230
(0xF4) LCDDR08 SEG131 SEG130 SEG129 SEG128 SEG127 SEG126 SEG125 SEG124 230
(0xF3) LCDDR07 SEG123 SEG122 SEG121 SEG120 SEG119 SEG118 SEG117 SEG116 230
(0xF2) LCDDR06 SEG115 SEG114 SEG113 SEG112 SEG111 SEG110 SEG109 SEG108 230
(0xF1) LCDDR05 SEG107 SEG106 SEG105 SEG104 SEG103 SEG102 SEG101 SEG100 230
(0xF0) LCDDR04 SEG039 SEG038 SEG037 SEG036 SEG035 SEG034 SEG033 SEG032 230
(0xEF) LCDDR03 SEG031 SEG030 SEG029 SEG028 SEG027 SEG026 SEG025 SEG024 230
(0xEE) LCDDR02 SEG023 SEG022 SEG021 SEG020 SEG019 SEG018 SEG017 SEG016 230
(0xED) LCDDR01 SEG015 SEG014 SEG013 SEG012 SEG011 SEG010 SEG009 SEG008 230
(0xEC) LCDDR00 SEG007 SEG006 SEG005 SEG004 SEG003 SEG002 SEG001 SEG000 230
(0xEB) Reserved --------
(0xEA) Reserved --------
(0xE9) Reserved --------
(0xE8) Reserved --------
(0xE7) LCDCCR LCDDC2 LCDDC1 LCDDC0 - LCDCC3 LCDCC2 LCDCC1 LCDCC0 229
(0xE6) LCDFRR - LCDPS2 LCDPS1 LCDPS0 - LCDCD2 LCDCD1 LCDCD0 227
(0xE5) LCDCRB LCDCS LCD2B LCDMUX1 LCDMUX0 LCDPM3 LCDPM2 LCDPM1 LCDPM0 225
(0xE4) LCDCRA LCDEN LCDAB - LCDIF LCDIE --LCDBL225
(0xE3) Reserved --------
(0xE2) Reserved --------
(0xE1) Reserved --------
(0xE0) Reserved --------
(0xDF) Reserved --------
(0xDE) Reserved --------
(0xDD) PORTJ -PORTJ6 PORTJ5 PORTJ4 PORTJ3 PORTJ2 PORTJ1 PORTJ0 80
(0xDC) DDRJ -DDJ6 DDJ5 DDJ4 DDJ3 DDJ2 DDJ1 DDJ0 80
(0xDB) PINJ -PINJ6 PINJ5 PINJ4 PINJ3 PINJ2 PINJ1 PINJ0 80
(0xDA) PORTH PORTH7 PORTH6 PORTH5 PORTH4 PORTH3 PORTH2 PORTH1 PORTH0 80
(0xD9) DDRH DDH7 DDH6 DDH5 DDH4 DDH3 DDH2 DDH1 DDH0 80
(0xD8) PINH PINH7 PINH6 PINH5 PINH4 PINH3 PINH2 PINH1 PINH0 80
(0xD7) Reserved --------
(0xD6) Reserved --------
(0xD5) Reserved --------
(0xD4) Reserved --------
(0xD3) Reserved --------
(0xD2) Reserved --------
(0xD1) Reserved --------
(0xD0) Reserved --------
(0xCF) Reserved --------
(0xCE) Reserved --------
(0xCD) Reserved --------
(0xCC) Reserved --------
(0xCB) Reserved --------
(0xCA) Reserved --------
(0xC9) Reserved --------
(0xC8) Reserved --------
(0xC7) Reserved --------
(0xC6) UDR0 USART0 Data Register 175
(0xC5) UBRR0H USART0 Baud Rate Register High 178
(0xC4) UBRR0L USART0 Baud Rate Register Low 178
(0xC3) Reserved --------
10 ATmega329/3290/649/6490
2552AS–AVR–11/04
(0xC2) UCSR0C - UMSEL0 UPM01 UPM00 USBS0 UCSZ01 UCSZ00 UCPOL0 177
(0xC1) UCSR0B RXCIE0 TXCIE0 UDRIE0 RXEN0 TXEN0 UCSZ02 RXB80 TXB80 176
(0xC0) UCSR0A RXC0 TXC0 UDRE0 FE0 DOR0 UPE0 U2X0 MPCM0 175
(0xBF) Reserved --------
(0xBE) Reserved --------
(0xBD) Reserved --------
(0xBC) Reserved --------
(0xBB) Reserved --------
(0xBA) USIDR USI Data Register 190
(0xB9) USISR USISIF USIOIF USIPF USIDC USICNT3 USICNT2 USICNT1 USICNT0 191
(0xB8) USICR USISIE USIOIE USIWM1 USIWM0 USICS1 USICS0 USICLK USITC 191
(0xB7) Reserved --------
(0xB6) ASSR --- EXCLK AS2 TCN2UB OCR2UB TCR2UB 143
(0xB5) Reserved --------
(0xB4) Reserved --------
(0xB3) OCR2A Timer/Counter 2 Output Compare Register A 142
(0xB2) TCNT2 Timer/Counter2 142
(0xB1) Reserved --------
(0xB0) TCCR2A FOC2A WGM20 COM2A1 COM2A0 WGM21 CS22 CS21 CS20 140
(0xAF) Reserved --------
(0xAE) Reserved --------
(0xAD) Reserved --------
(0xAC) Reserved --------
(0xAB) Reserved --------
(0xAA) Reserved --------
(0xA9) Reserved --------
(0xA8) Reserved --------
(0xA7) Reserved --------
(0xA6) Reserved --------
(0xA5) Reserved --------
(0xA4) Reserved --------
(0xA3) Reserved --------
(0xA2) Reserved --------
(0xA1) Reserved --------
(0xA0) Reserved --------
(0x9F) Reserved --------
(0x9E) Reserved --------
(0x9D) Reserved --------
(0x9C) Reserved --------
(0x9B) Reserved --------
(0x9A) Reserved --------
(0x99) Reserved --------
(0x98) Reserved --------
(0x97) Reserved --------
(0x96) Reserved --------
(0x95) Reserved --------
(0x94) Reserved --------
(0x93) Reserved --------
(0x92) Reserved --------
(0x91) Reserved --------
(0x90) Reserved --------
(0x8F) Reserved --------
(0x8E) Reserved --------
(0x8D) Reserved --------
(0x8C) Reserved --------
(0x8B) OCR1BH Timer/Counter1 Output Compare Register B High 126
(0x8A) OCR1BL Timer/Counter1 Output Compare Register B Low 126
(0x89) OCR1AH Timer/Counter1 Output Compare Register A High 126
(0x88) OCR1AL Timer/Counter1 Output Compare Register A Low 126
(0x87) ICR1H Timer/Counter1 Input Capture Register High 126
(0x86) ICR1L Timer/Counter1 Input Capture Register Low 126
(0x85) TCNT1H Timer/Counter1 High 126
(0x84) TCNT1L Timer/Counter1 Low 126
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
11
ATmega329/3290/649/6490
2552AS–AVR–11/04
(0x83) Reserved --------
(0x82) TCCR1C FOC1A FOC1B ------125
(0x81) TCCR1B ICNC1 ICES1 - WGM13WGM12CS12CS11CS10 124
(0x80) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 --WGM11WGM10122
(0x7F) DIDR1 ------ AIN1D AIN0D 197
(0x7E) DIDR0 ADC7D ADC6D ADC5D ADC4D ADC3D ADC2D ADC1D ADC0D 214
(0x7D) Reserved --------
(0x7C) ADMUX REFS1 REFS0 ADLAR MUX4 MUX3 MUX2 MUX1 MUX0 210
(0x7B) ADCSRB -ACME- - - ADTS2 ADTS1 ADTS0 195/213
(0x7A) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 212
(0x79) ADCH ADC Data Register High 213
(0x78) ADCL ADC Data Register Low 213
(0x77) Reserved --------
(0x76) Reserved --------
(0x75) Reserved --------
(0x74) Reserved --------
(0x73) PCMSK3 -PCINT30 PCINT29 PCINT28 PCINT27 PCINT26 PCINT25 PCINT24 83
(0x72) Reserved --------
(0x71) Reserved --------
(0x70) TIMSK2 ------ OCIE2A TOIE2 145
(0x6F) TIMSK1 --ICIE1-- OCIE1B OCIE1A TOIE1 127
(0x6E) TIMSK0 ------ OCIE0A TOIE0 98
(0x6D) PCMSK2 PCINT23 PCINT22 PCINT21 PCINT20 PCINT19 PCINT18 PCINT17 PCINT16 84
(0x6C) PCMSK1 PCINT15 PCINT14 PCINT13 PCINT12 PCINT11 PCINT10 PCINT9 PCINT8 84
(0x6B) PCMSK0 PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 84
(0x6A) Reserved --------
(0x69) EICRA ------ISC01ISC0081
(0x68) Reserved --------
(0x67) Reserved --------
(0x66) OSCCAL Oscillator Calibration Register [CAL7..0] 29
(0x65) Reserved --------
(0x64) PRR --- PRLCD PRTIM1 PRSPI PSUSART0 PRADC 35
(0x63) Reserved --------
(0x62) Reserved --------
(0x61) CLKPR CLKPCE --- CLKPS3 CLKPS2 CLKPS1 CLKPS0 31
(0x60) WDTCR --- WDCE WDE WDP2 WDP1 WDP0 44
0x3F (0x5F) SREG I T H S V N Z C 11
0x3E (0x5E) SPH Stack Pointer High 13
0x3D (0x5D) SPL Stack Pointer Low 13
0x3C (0x5C) Reserved --------
0x3B (0x5B) Reserved --------
0x3A (0x5A) Reserved --------
0x39 (0x59) Reserved --------
0x38 (0x58) Reserved --------
0x37 (0x57) SPMCSR SPMIE RWWSB - RWWSRE BLBSET PGWRT PGERS SPMEN 267
0x36 (0x56) Reserved
0x35 (0x55) MCUCR JTD - -PUD- - IVSEL IVCE 50/59/240
0x34 (0x54) MCUSR --- JTRF WDRF BORF EXTRF PORF 42
0x33 (0x53) SMCR ---- SM2 SM1 SM0 SE 33
0x32 (0x52) Reserved --------
0x31 (0x51) OCDR IDRD/OCDR7 OCDR6 OCDR5 OCDR4 OCDR3 OCDR2 OCDR1 OCDR0 236
0x30 (0x50) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 195
0x2F (0x4F) Reserved --------
0x2E (0x4E) SPDR SPI Data Register 155
0x2D (0x4D) SPSR SPIF WCOL ----- SPI2X 155
0x2C (0x4C) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 153
0x2B (0x4B) GPIOR2 General Purpose I/O Register 24
0x2A (0x4A) GPIOR1 General Purpose I/O Register 24
0x29 (0x49) Reserved --------
0x28 (0x48) Reserved --------
0x27 (0x47) OCR0A Timer/Counter0 Output Compare A 98
0x26 (0x46) TCNT0 Timer/Counter0 97
0x25 (0x45) Reserved --------
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
12 ATmega329/3290/649/6490
2552AS–AVR–11/04
Note: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
should never be written.
2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The
ATmega329/3290/649/6490 is a complex microcontroller with more peripheral units than can be supported within the 64
location reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only
the ST/STS/STD and LD/LDS/LDD instructions can be used.
0x24 (0x44) TCCR0A FOC0A WGM00 COM0A1 COM0A0 WGM01 CS02 CS01 CS00 95
0x23 (0x43) GTCCR TSM ----- PSR2 PSR10 100/147
0x22 (0x42) EEARH ----- EEPROM Address Register High 20
0x21 (0x41) EEARL EEPROM Address Register Low 20
0x20 (0x40) EEDR EEPROM Data Register 20
0x1F (0x3F) EECR ---- EERIE EEMWE EEWE EERE 20
0x1E (0x3E) GPIOR0 General Purpose I/O Register 24
0x1D (0x3D) EIMSK PCIE3 PCIE2 PCIE1 PCIE0 ---INT082
0x1C (0x3C) EIFR PCIF3 PCIF2 PCIF1 PCIF0 - - - INTF0 83
0x1B (0x3B) Reserved --------
0x1A (0x3A) Reserved --------
0x19 (0x39) Reserved --------
0x18 (0x38) Reserved --------
0x17 (0x37) TIFR2 ------OCF2ATOV2145
0x16 (0x36) TIFR1 --ICF1--OCF1BOCF1ATOV1127
0x15 (0x35) TIFR0 ------OCF0ATOV098
0x14 (0x34) PORTG --- PORTG4 PORTG3 PORTG2 PORTG1 PORTG0 80
0x13 (0x33) DDRG --- DDG4 DDG3 DDG2 DDG1 DDG0 80
0x12 (0x32) PING -- PING5 PING4 PING3 PING2 PING1 PING0 80
0x11 (0x31) PORTF PORTF7 PORTF6 PORTF5 PORTF4 PORTF3 PORTF2 PORTF1 PORTF0 79
0x10 (0x30) DDRF DDF7 DDF6 DDF5 DDF4 DDF3 DDF2 DDF1 DDF0 79
0x0F (0x2F) PINF PINF7 PINF6 PINF5 PINF4 PINF3 PINF2 PINF1 PINF0 79
0x0E (0x2E) PORTE PORTE7 PORTE6 PORTE5 PORTE4 PORTE3 PORTE2 PORTE1 PORTE0 79
0x0D (0x2D) DDRE DDE7 DDE6 DDE5 DDE4 DDE3 DDE2 DDE1 DDE0 79
0x0C (0x2C) PINE PINE7 PINE6 PINE5 PINE4 PINE3 PINE2 PINE1 PINE0 79
0x0B (0x2B) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 79
0x0A (0x2A) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 79
0x09 (0x29) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 79
0x08 (0x28) PORTC PORTC7 PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 78
0x07 (0x27) DDRC DDC7 DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 78
0x06 (0x26) PINC PINC7 PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 78
0x05 (0x25) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 78
0x04 (0x24) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 78
0x03 (0x23) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 78
0x02 (0x22) P O R TA P O R TA 7 P O R TA 6 P O R TA 5 P O R TA 4 P O RTA 3 P O R TA 2 P O R TA 1 P O R TA 0 7 8
0x01 (0x21) DDRA DDA7 DDA6 DDA5 DDA4 DDA3 DDA2 DDA1 DDA0 78
0x00 (0x20) PINA PINA7 PINA6 PINA5 PINA4 PINA3 PINA2 PINA1 PINA0 78
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page
13
ATmega329/3290/649/6490
2552AS–AVR–11/04
Instruction Set Summary
Mnemonics Operands Description Operation Flags #Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD Rd, Rr Add two Registers Rd Rd + Rr Z,C,N,V,H 1
ADC Rd, Rr Add with Carry two Registers Rd Rd + Rr + C Z,C,N,V,H 1
ADIW Rdl,K Add Immediate to Word Rdh:Rdl Rdh:Rdl + K Z,C,N,V,S 2
SUB Rd, Rr Subtract two Registers Rd Rd - Rr Z,C,N,V,H 1
SUBI Rd, K Subtract Constant from Register Rd Rd - K Z,C,N,V,H 1
SBC Rd, Rr Subtract with Carry two Registers Rd Rd - Rr - C Z,C,N,V,H 1
SBCI Rd, K Subtract with Carry Constant from Reg. Rd Rd - K - C Z,C,N,V,H 1
SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl Rdh:Rdl - K Z,C,N,V,S 2
AND Rd, Rr Logical AND Registers Rd Rd Rr Z,N,V 1
ANDI Rd, K Logical AND Register and Constant Rd Rd K Z,N,V 1
OR Rd, Rr Logical OR Registers Rd Rd v Rr Z,N,V 1
ORI Rd, K Logical OR Register and Constant Rd Rd v K Z,N,V 1
EOR Rd, Rr Exclusive OR Registers Rd Rd Rr Z,N,V 1
COM Rd One’s Complement Rd 0xFF Rd Z,C,N,V 1
NEG Rd Two’s Complement Rd 0x00 Rd Z,C,N,V,H 1
SBR Rd,K Set Bit(s) in Register Rd Rd v K Z,N,V 1
CBR Rd,K Clear Bit(s) in Register Rd Rd (0xFF - K) Z,N,V 1
INC Rd Increment Rd Rd + 1 Z,N,V 1
DEC Rd Decrement Rd Rd 1 Z,N,V 1
TST Rd Test for Zero or Minus Rd Rd Rd Z,N,V 1
CLR Rd Clear Register Rd Rd Rd Z,N,V 1
SER Rd Set Register Rd 0xFF None 1
MUL Rd, Rr Multiply Unsigned R1:R0 Rd x Rr Z,C 2
MULS Rd, Rr Multiply Signed R1:R0 Rd x Rr Z,C 2
MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 Rd x Rr Z,C 2
FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 (Rd x Rr) << 1 Z,C 2
FMULS Rd, Rr Fractional Multiply Signed R1:R0 (Rd x Rr) << 1 Z,C 2
FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 (Rd x Rr) << 1 Z,C 2
BRANCH INSTRUCTIONS
RJMP k Relative Jump PC PC + k + 1 None 2
IJMP Indirect Jump to (Z) PC Z None 2
JMP k Direct Jump PC kNone3
RCALL k Relative Subroutine Call PC PC + k + 1 None 3
ICALL Indirect Call to (Z) PC ZNone3
CALL k Direct Subroutine Call PC kNone4
RET Subroutine Return PC STACK None 4
RETI Interrupt Return PC STACK I 4
CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC PC + 2 or 3 None 1/2/3
CP Rd,Rr Compare Rd Rr Z, N,V,C,H 1
CPC Rd,Rr Compare with Carry Rd Rr C Z, N,V,C,H 1
CPI Rd,K Compare Register with Immediate Rd K Z, N,V,C,H 1
SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC PC + 2 or 3 None 1/2/3
SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC PC + 2 or 3 None 1/2/3
SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC PC + 2 or 3 None 1/2/3
SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC PC + 2 or 3 None 1/2/3
BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PCPC+k + 1 None 1/2
BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PCPC+k + 1 None 1/2
BREQ k Branch if Equal if (Z = 1) then PC PC + k + 1 None 1/2
BRNE k Branch if Not Equal if (Z = 0) then PC PC + k + 1 None 1/2
BRCS k Branch if Carry Set if (C = 1) then PC PC + k + 1 None 1/2
BRCC k Branch if Carry Cleared if (C = 0) then PC PC + k + 1 None 1/2
BRSH k Branch if Same or Higher if (C = 0) then PC PC + k + 1 None 1/2
BRLO k Branch if Lower if (C = 1) then PC PC + k + 1 None 1/2
BRMI k Branch if Minus if (N = 1) then PC PC + k + 1 None 1/2
BRPL k Branch if Plus if (N = 0) then PC PC + k + 1 None 1/2
BRGE k Branch if Greater or Equal, Signed if (N V= 0) then PC PC + k + 1 None 1/2
BRLT k Branch if Less Than Zero, Signed if (N V= 1) then PC PC + k + 1 None 1/2
BRHS k Branch if Half Carry Flag Set if (H = 1) then PC PC + k + 1 None 1/2
BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC PC + k + 1 None 1/2
BRTS k Branch if T Flag Set if (T = 1) then PC PC + k + 1 None 1/2
BRTC k Branch if T Flag Cleared if (T = 0) then PC PC + k + 1 None 1/2
BRVS k Branch if Overflow Flag is Set if (V = 1) then PC PC + k + 1 None 1/2
BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC PC + k + 1 None 1/2
14 ATmega329/3290/649/6490
2552AS–AVR–11/04
BRIE k Branch if Interrupt Enabled if ( I = 1) then PC PC + k + 1 None 1/2
BRID k Branch if Interrupt Disabled if ( I = 0) then PC PC + k + 1 None 1/2
BIT AND BIT-TEST INSTRUCTIONS
SBI P,b Set Bit in I/O Register I/O(P,b) 1None2
CBI P,b Clear Bit in I/O Register I/O(P,b) 0None2
LSL Rd Logical Shift Left Rd(n+1) Rd(n), Rd(0) 0 Z,C,N,V 1
LSR Rd Logical Shift Right Rd(n) Rd(n+1), Rd(7) 0 Z,C,N,V 1
ROL Rd Rotate Left Through Carry Rd(0)C,Rd(n+1) Rd(n),CRd(7) Z,C,N,V 1
ROR Rd Rotate Right Through Carry Rd(7)C,Rd(n) Rd(n+1),CRd(0) Z,C,N,V 1
ASR Rd Arithmetic Shift Right Rd(n) Rd(n+1), n=0..6 Z,C,N,V 1
SWAP Rd Swap Nibbles Rd(3..0)Rd(7..4),Rd(7..4)Rd(3..0) None 1
BSET s Flag Set SREG(s) 1 SREG(s) 1
BCLR s Flag Clear SREG(s) 0 SREG(s) 1
BST Rr, b Bit Store from Register to T T Rr(b) T 1
BLD Rd, b Bit load from T to Register Rd(b) TNone1
SEC Set Carry C 1C1
CLC Clear Carry C 0 C 1
SEN Set Negative Flag N 1N1
CLN Clear Negative Flag N 0 N 1
SEZ Set Zero Flag Z 1Z1
CLZ Clear Zero Flag Z 0 Z 1
SEI Global Interrupt Enable I 1I1
CLI Global Interrupt Disable I 0 I 1
SES Set Signed Test Flag S 1S1
CLS Clear Signed Test Flag S 0 S 1
SEV Set Twos Complement Overflow. V 1V1
CLV Clear Twos Complement Overflow V 0 V 1
SET Set T in SREG T 1T1
CLT Clear T in SREG T 0 T 1
SEH Set Half Carry Flag in SREG H 1H1
CLH Clear Half Carry Flag in SREG H 0 H 1
DATA TRANSFER INSTRUCTIONS
MOV Rd, Rr Move Between Registers Rd Rr None 1
MOVW Rd, Rr Copy Register Word Rd+1:Rd Rr+1:Rr None 1
LDI Rd, K Load Immediate Rd KNone1
LD Rd, X Load Indirect Rd (X) None 2
LD Rd, X+ Load Indirect and Post-Inc. Rd (X), X X + 1 None 2
LD Rd, - X Load Indirect and Pre-Dec. X X - 1, Rd (X) None 2
LD Rd, Y Load Indirect Rd (Y) None 2
LD Rd, Y+ Load Indirect and Post-Inc. Rd (Y), Y Y + 1 None 2
LD Rd, - Y Load Indirect and Pre-Dec. Y Y - 1, Rd (Y) None 2
LDD Rd,Y+q Load Indirect with Displacement Rd (Y + q) None 2
LD Rd, Z Load Indirect Rd (Z) None 2
LD Rd, Z+ Load Indirect and Post-Inc. Rd (Z), Z Z+1 None 2
LD Rd, -Z Load Indirect and Pre-Dec. Z Z - 1, Rd (Z) None 2
LDD Rd, Z+q Load Indirect with Displacement Rd (Z + q) None 2
LDS Rd, k Load Direct from SRAM Rd (k) None 2
ST X, Rr Store Indirect (X) Rr None 2
ST X+, Rr Store Indirect and Post-Inc. (X) Rr, X X + 1 None 2
ST - X, Rr Store Indirect and Pre-Dec. X X - 1, (X) Rr None 2
ST Y, Rr Store Indirect (Y) Rr None 2
ST Y+, Rr Store Indirect and Post-Inc. (Y) Rr, Y Y + 1 None 2
ST - Y, Rr Store Indirect and Pre-Dec. Y Y - 1, (Y) Rr None 2
STD Y+q,Rr Store Indirect with Displacement (Y + q) Rr None 2
ST Z, Rr Store Indirect (Z) Rr None 2
ST Z+, Rr Store Indirect and Post-Inc. (Z) Rr, Z Z + 1 None 2
ST -Z, Rr Store Indirect and Pre-Dec. Z Z - 1, (Z) Rr None 2
STD Z+q,Rr Store Indirect with Displacement (Z + q) Rr None 2
STS k, Rr Store Direct to SRAM (k) Rr None 2
LPM Load Program Memory R0 (Z) None 3
LPM Rd, Z Load Program Memory Rd (Z) None 3
LPM Rd, Z+ Load Program Memory and Post-Inc Rd (Z), Z Z+1 None 3
SPM Store Program Memory (Z) R1:R0 None -
IN Rd, P In Port Rd PNone1
OUT P, Rr Out Port P Rr None 1
PUSH Rr Push Register on Stack STACK Rr None 2
Mnemonics Operands Description Operation Flags #Clocks
15
ATmega329/3290/649/6490
2552AS–AVR–11/04
POP Rd Pop Register from Stack Rd STACK None 2
MCU CONTROL INSTRUCTIONS
NOP No Operation None 1
SLEEP Sleep (see specific descr. for Sleep function) None 1
WDR Watchdog Reset (see specific descr. for WDR/timer) None 1
BREAK Break For On-chip Debug Only None N/A
Mnemonics Operands Description Operation Flags #Clocks
16 ATmega329/3290/649/6490
2552AS–AVR–11/04
Ordering Information
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 136 on page 309 and Figure 137 on page 310.
ATmega329
Speed (MHz)(3) Power Supply Ordering Code Package Type(1) Operational Range
8 1.8 - 5.5V
ATmega329V-8AI
ATmega329V-8AU(2)
ATmega329V-8MI
ATmega329V-8MU(2)
64A
64A
64M1
64M1
Industrial
(-40°C to 85°C)
16 4.5 - 5.5V
ATmega329-16AI
ATmega329-16AU(2)
ATmega329-16MI
ATmega329-16MU(2)
64A
64A
64M1
64M1
Industrial
(-40°C to 85°C)
Package Type
64A 64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1 64-pad, 9 x 9 x 1.0 mm, Micro Lead Frame Package (MLF)
100A 100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
17
ATmega329/3290/649/6490
2552AS–AVR–11/04
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 136 on page 309 and Figure 137 on page 310.
ATmega3290
Speed (MHz)(3) Power Supply Ordering Code Package Type(1) Operational Range
8 1.8 - 5.5V ATmega3290V-8AI
ATmega3290V-8AU(2)
100A
100A
Industrial
(-40°C to 85°C)
16 4.5 - 5.5V ATmega3290-16AI
ATmega3290-16AU(2)
100A
100A
Industrial
(-40°C to 85°C)
Package Type
64A 64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1 64-pad, 9 x 9 x 1.0 mm, Micro Lead Frame Package (MLF)
100A 100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
18 ATmega329/3290/649/6490
2552AS–AVR–11/04
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 136 on page 309 and Figure 137 on page 310.
ATmega649
Speed (MHz)(3) Power Supply Ordering Code Package Type(1) Operational Range
8 1.8 - 5.5V
ATmega649V-8AI
ATmega649V-8AU(2)
ATmega649V-8MI
ATmega649V-8MU(2)
64A
64A
64M1
64M1
Industrial
(-40°C to 85°C)
16 4.5 - 5.5V
ATmega649-16AI
ATmega649-16AU(2)
ATmega649-16MI
ATmega649-16MU(2)
64A
64A
64M1
64M1
Industrial
(-40°C to 85°C)
Package Type
64A 64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1 64-pad, 9 x 9 x 1.0 mm, Micro Lead Frame Package (MLF)
100A 100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
19
ATmega329/3290/649/6490
2552AS–AVR–11/04
Notes: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information
and minimum quantities.
2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS direc-
tive). Also Halide free and fully Green.
3. For Speed vs. VCC see Figure 136 on page 309 and Figure 137 on page 310.
ATmega6490
Speed (MHz)(3) Power Supply Ordering Code Package Type(1) Operational Range
8 1.8 - 5.5V ATmega6490V-8AI
ATmega6490V-8AU(2)
100A
100A
Industrial
(-40°C to 85°C)
16 4.5 - 5.5V ATmega6490-16AI
ATmega6490-16AU(2)
100A
100A
Industrial
(-40°C to 85°C)
Package Type
64A 64-lead, 14 x 14 x 1.0 mm, Thin Profile Plastic Quad Flat Package (TQFP)
64M1 64-pad, 9 x 9 x 1.0 mm, Micro Lead Frame Package (MLF)
100A 100-lead, 14 x 14 x 1.0 mm, 0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP)
20 ATmega329/3290/649/6490
2552AS–AVR–11/04
Packaging Information
64A
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
64A, 64-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness,
0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) B
64A
10/5/2001
PIN 1 IDENTIFIER
0˚~7˚
PIN 1
L
C
A1 A2 A
D1
D
eE1 E
B
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
Notes: 1. This package conforms to JEDEC reference MS-026, Variation AEB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10 mm maximum.
A 1.20
A1 0.05 0.15
A2 0.95 1.00 1.05
D 15.75 16.00 16.25
D1 13.90 14.00 14.10 Note 2
E 15.75 16.00 16.25
E1 13.90 14.00 14.10 Note 2
B 0.30 0.45
C 0.09 0.20
L 0.45 0.75
e 0.80 TYP
21
ATmega329/3290/649/6490
2552AS–AVR–11/04
64M1
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
64M1, 64-pad, 9 x 9 x 1.0 mm Body, Lead Pitch 0.50 mm,
D
64M1
8/19/04
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A 0.80 0.90 1.00
A1 0.02 0.05
b 0.23 0.25 0.28
D 9.00 BSC
D2 5.20 5.40 5.60
E 9.00 BSC
E2 5.20 5.40 5.60
e 0.50 BSC
L 0.35 0.40 0.45
Note: JEDEC Standard MO-220, (SAW Singulation) Fig. 1, VMMD.
TOP VIEW
SIDE VIEW
BOTTOM VIEW
D
E
Marked Pin# 1 ID
SEATING PLANE
A1
C
A
C
0.08
1
2
3
K 0.20
E2
D2
be
Pin #1 Corner
L
Pin #1
Triangle
Pin #1
Chamfer
(C 0.30)
Option A
Option B
Pin #1
Notch
(0.20 R)
Option C
K
K
5.40 mm Exposed Pad, Micro Lead Frame Package (MLF)
22 ATmega329/3290/649/6490
2552AS–AVR–11/04
100A
2325 Orchard Parkway
San Jose, CA 95131
TITLE DRAWING NO.
R
REV.
100A, 100-lead, 14 x 14 mm Body Size, 1.0 mm Body Thickness,
0.5 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) C
100A
10/5/2001
PIN 1 IDENTIFIER
0˚~7˚
PIN 1
L
C
A1 A2 A
D1
D
eE1 E
B
A 1.20
A1 0.05 0.15
A2 0.95 1.00 1.05
D 15.75 16.00 16.25
D1 13.90 14.00 14.10 Note 2
E 15.75 16.00 16.25
E1 13.90 14.00 14.10 Note 2
B 0.17 0.27
C 0.09 0.20
L 0.45 0.75
e 0.50 TYP
Notes: 1. This package conforms to JEDEC reference MS-026, Variation AED.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.08 mm maximum.
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
23
ATmega329/3290/649/6490
2552AS–AVR–11/04
Errata
ATmega329 rev. A
LCD contrast voltage too high
1. LCD contrast voltage too high
When the LCD is active and using low power waveform, the LCD contrast voltage
can be too high. This occurs when VCC is higher than VLCD, and when using low
LCD drivetime.
Problem Fix/Workaround
There are several possible workarounds:
- Use normal waveform instead of low power waveform
- Use drivetime of 375 µs or longer
ATmega3290 rev. A
LCD contrast voltage too high
1. LCD contrast voltage too high
When the LCD is active and using low power waveform, the LCD contrast voltage
can be too high. This occurs when VCC is higher than VLCD, and when using low
LCD drivetime.
Problem Fix/Workaround
There are several possible workarounds:
- Use normal waveform instead of low power waveform
- Use drivetime of 375 µs or longer
ATmega649 rev. A
There is no errata for this revision of ATmega649.
ATmega6490 rev. A
There is no errata for this revision of ATmega6490.
24 ATmega329/3290/649/6490
2552AS–AVR–11/04
Datasheet Revision
History
Please note that the referring page numbers in this section are referring to this docu-
ment.The referring revision in this section are referring to the document revision.
Rev. 2552A-11/04
1. Initial version.
Printed on recycled paper.
2552AS–AVR–11/04
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI-
TIONS OF SALE LOCATED ON ATMELS WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDEN-
TAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT
OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications
and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Atmel’s products are not
intended, authorized, or warranted for use as components in applications intended to support or sustain life.
Atmel Corporation Atmel Operations
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 487-2600
Regional Headquarters
Europe
Atmel Sarl
Route des Arsenaux 41
Case Postale 80
CH-1705 Fribourg
Switzerland
Tel: (41) 26-426-5555
Fax: (41) 26-426-5500
Asia
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimshatsui
East Kowloon
Hong Kong
Tel: (852) 2721-9778
Fax: (852) 2722-1369
Japan
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
Tel: (81) 3-3523-3551
Fax: (81) 3-3523-7581
Memory
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
Microcontrollers
2325 Orchard Parkway
San Jose, CA 95131, USA
Tel: 1(408) 441-0311
Fax: 1(408) 436-4314
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
Tel: (33) 2-40-18-18-18
Fax: (33) 2-40-18-19-60
ASIC/ASSP/Smart Cards
Zone Industrielle
13106 Rousset Cedex, France
Tel: (33) 4-42-53-60-00
Fax: (33) 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Scottish Enterprise Technology Park
Maxwell Building
East Kilbride G75 0QR, Scotland
Tel: (44) 1355-803-000
Fax: (44) 1355-242-743
RF/Automotive
Theresienstrasse 2
Postfach 3535
74025 Heilbronn, Germany
Tel: (49) 71-31-67-0
Fax: (49) 71-31-67-2340
1150 East Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906, USA
Tel: 1(719) 576-3300
Fax: 1(719) 540-1759
Biometrics/Imaging/Hi-Rel MPU/
High Speed Converters/RF Datacom
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
Tel: (33) 4-76-58-30-00
Fax: (33) 4-76-58-34-80
Literature Requests
www.atmel.com/literature
© Atmel Corporation 2004. All rights reserved. Atmel®, logo and combinations thereof, AVR®, and AVR Studio® are registered trademarks,
and Everywhere You AreSM are the trademarks of Atmel Corporation or its subsidiaries. Microsoft®, Windows®, Windows NT®, and Windows XP®
are the registered trademarks of Microsoft Corporation. Other terms and product names may be trademarks of others.