Issue 3 - May 2006 1 www.zetex.com
© Zetex Semiconductors plc 2006
BSP75N
60V self-protected low-side Intellifet
TM
MOSFET switch
Summary
Continuous drain source voltage VDS=60V
On-state resistance 550m⍀
Nominal load current 1.2A (VIN = 5V)
Clamping energy 550mJ
Ordering information
Device marking
BSP75N
Description
Self-protected low side MOSFET. Monolithic over temperature, over
current, over voltage (active clamp) and ESD protected logic level
power MOSFET intended as a general purpose switch.
Features
• Short circuit protection with auto restart
• Over-voltage protection (active clamp)
• Thermal shutdown with auto restart
• Over-current protection
• Input protection (ESD)
• High continuous current rating
• Load dump protection (actively protects load)
• Logic level input
Note:
The tab is connected to the source pin and must
be electrically isolated from the drain pin.
Connection of significant copper to the drain pin
is recommended for best thermal performance.
Device Reel size
(inches)
Tape width
(mm)
Quantity per reel
BSP75NTA 7 12mm embossed 1,000
BSP75NTC 13 12mm embossed 4,000
SOT223
S
S
D
IN
BSP75N
Issue 3 - May 2006 2 www.zetex.com
© Zetex Semiconductors plc 2006
Functional block diagram
Applications
• Especially suited for loads with a high in-rush current such as lamps and motors.
• All types of resistive, inductive and capacitive loads in switching applications.
•C compatible power switch for 12V and 24V DC applications.
• Automotive rated.
• Replaces electromechanical relays and discrete circuits.
• Linear mode capability - the current-limiting protection circuitry is designed to de-activate at
low Vds, in order not to compromise the load current during normal operation. The design
maximum DC operating current is therefore determined by the thermal capability of the
package/board combination, rather than by the protection circuitry.
S
Over voltage
protection
Over current
protection
Over temperature
protection
Logic
Human body
ESD protection
D
IN dV/dt
limitation
BSP75N
Issue 3 - May 2006 3 www.zetex.com
© Zetex Semiconductors plc 2006
Absolute maximum ratings
NOTES:
(a) For a device surface mounted on 25mm x 25mm x 1.6mm FR4 board with a high coverage of single sided 2oz weight
copper. Allocation of 6cm2 copper 33% to source tab and 66% to drain pin with tab and drain pin electrically isolated.
(b) For a device surface mounted on FR4 board as (a) and measured at t<=10s.
(c) For a device surface mounted on FR4 board with the minimum copper required for connections.
Parameter Symbol Limit Unit
Continuous drain-source voltage VDS 60 V
Drain-source voltage for short circuit protection VIN = 5V VDS(SC) 36 V
Drain-source voltage for short circuit protection VIN = 10V VDS(SC) 20 V
Continuous input voltage VIN -0.2 ... +10 V
Peak input voltage VIN -0.2 ... +20 V
Operating temperature range Tj,
-40 to +150
°C
Storage temperature range Tstg
-55 to +150
°C
Power dissipation at TA =25°C (a) PD 1.5 W
Power dissipation at TA =25°C (c) PD0.6 W
Continuous drain current @ VIN=10V; TA=25°C (a) ID 1.2 A
Continuous drain current @ VIN=5V; TA=25°C (a) ID 1.1 A
Continuous drain current @ VIN=5V; TA=25°C (c) ID 0.7 A
Pulsed drain current @ VIN=10V IDM 2.5 A
Continuous source current (body diode) (a) IS2.0 A
Pulsed source current (body diode) (b) IS3.3 A
Unclamped single pulse inductive energy EAS 550 mJ
Load dump protection VLoadDump 80 V
Electrostatic discharge (human body model) VESD 4000 V
DIN humidity category, DIN 40 040 E
IEC climatic category, DIN IEC 68-1 40/150/56
Thermal resistance
Parameter Symbol Limit Unit
Junction to ambient (a) R⍜JA 83 °C/W
Junction to ambient (b) R⍜JA 45 °C/W
Junction to ambient (c) R⍜JA 208 °C/W
BSP75N
Issue 3 - May 2006 4 www.zetex.com
© Zetex Semiconductors plc 2006
Characteristics
NOTES:
(a) For a device surface mounted on 25mm x 25mm x 1.6mm FR4 board with a high coverage of single sided 2oz weight
copper. Allocation of 6cm2 copper 33% to source tab and 66% to drain pin with tab and drain pin electrically isolated.
BSP75N
Issue 3 - May 2006 5 www.zetex.com
© Zetex Semiconductors plc 2006
Electrical characteristics (at TAMB = 25°C unless otherwise stated)
Parameter Symbol Min. Typ. Max. Unit Conditions
Static characteristics
Drain-source clamp voltage VDS(AZ) 60 70 75 V ID=10mA
Off-state drain current IDSS 0.1 3 AVDS=12V, VIN=0V
Off-state drain current IDSS 315AVDS=32V, VIN=0V
Input threshold voltage (*)
NOTES:
(*) The drain current is limited to a reduced value when VDS exceeds a safe level.
VIN(th) 12.1 VV
DS=VGS, ID=1mA
Input current IIN 0.7 1.2 mA VIN=+5V
Input current IIN 1.5 2.7 mA VIN=+7V
Input current IIN 47mAV
IN=+10V
Static drain-source on-state
resistance
RDS(on) 520 675 m⍀VIN=+5V, ID=0.7A
Static drain-source on-state
resistance
RDS(on) 385 550 m⍀VIN=+10V, ID=0.7A
Current limit (†)
(†) Protection features may operate outside spec for VIN<4.5V.
ID(LIM) 0.7 1.0 1.5 A VIN=+5V, VDS>5V
Current limit(†) ID(LIM) 1.0 1.8 2.3 A VIN=+10V, VDS>5V
Dynamic characteristics
Turn-on time (VIN to 90% ID)t
on 3.0 10 sR
L=22⍀, VDD=12V,
VIN=0 to +10V
Turn-off time (VIN to 90% ID)t
off 13 20 sR
L=22⍀, VDD=12V,
VIN=+10V to 0V
Slew rate on (70 to 50% VDD)-dV
DS/dton 820V/sR
L=22⍀, VDD=12V,
VIN=0 to +10V
Slew rate off (50 to 70% VDD)DV
DS/dtoff 3.2 10 V/sR
L=22⍀, VDD=12V,
VIN=+10V to 0V
Protection functions (‡)
(‡) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
datasheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not designed
for continuous, repetitive operation.
Required input voltage for
over temperature protection
VPROT 4.5 V
Thermal overload trip
temperature
TJT 150 175 °C
Thermal hysteresis 1 °C
Unclamped single pulse
inductive energy Tj=25°C
EAS 550 mJ ID(ISO)=0.7A,
VDD=32V
Unclamped single pulse
inductive energy Tj=150°C
200 mJ ID(ISO)=0.7A,
VDD=32V
Inverse diode
Source drain voltage VSD 1VV
IN=0V, -ID=1.4A
BSP75N
Issue 3 - May 2006 8 www.zetex.com
© Zetex Semiconductors plc 2006
For international sales offices visit www.zetex.com/offices
Zetex products are distributed worldwide. For details, see www.zetex.com/salesnetwork
This publication is issued to provide outline information only which (unless agreed by the company in writing) may not be used, applied or
reproduced for any purpose or form part of any order or contact or be regarded as a representation relating to the products or services concerned.
The company reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service.
Europe
Zetex GmbH
Streitfeldstraße 19
D-81673 München
Germany
Telefon: (49) 89 45 49 49 0
Fax: (49) 89 45 49 49 49
europe.sales@zetex.com
Americas
Zetex Inc
700 Veterans Memorial Highway
Hauppauge, NY 11788
USA
Telephone: (1) 631 360 2222
Fax: (1) 631 360 8222
usa.sales@zetex.com
Asia Pacific
Zetex (Asia Ltd)
3701-04 Metroplaza Tower 1
Hing Fong Road, Kwai Fong
Hong Kong
Telephone: (852) 26100 611
Fax: (852) 24250 494
asia.sales@zetex.com
Corporate Headquarters
Zetex Semiconductors plc
Zetex Technology Park, Chadderton
Oldham, OL9 9LL
United Kingdom
Telephone: (44) 161 622 4444
Fax: (44) 161 622 4446
hq@zetex.com
Package outline - SOT223
Note: Controlling dimensions are in millimeters. Approximate dimensions are provided in inches
Dim. Millimeters Inches Dim. Millimeters Inches
Min. Max. Min. Max. Min. Max. Min. Max.
A - 1.80 - 0.071 e 2.30 BSC 0.0905 BSC
A1 0.02 0.10 0.0008 0.004 e1 4.60 BSC 0.181 BSC
b 0.66 0.84 0.026 0.033 E 6.70 7.30 0.264 0.287
b2 2.90 3.10 0.114 0.122 E1 3.30 3.70 0.130 0.146
C 0.23 0.33 0.009 0.013 L 0.90 - 0.355 -
D 6.30 6.70 0.248 0.264 - - - - -
