E2A-S08KS02-WP-B12M - Omron Electronics

Ordering Information (Shaded models are normally stocked.)

Cylindrical Proximity Sensor

E2A

Extended Range DC-3 Wire

Proximity Sensors

•Ensures a sensing distance approximately

1.5 to 2 times longer than standard

proximity sensors.

• Minimizes collisions.

• Full range of standard sizes (M8, M12, M18

and M30; both long and short barrels).

•Choose from prewired, M8 or M12

connector versions.

E2A-S08KS02-WP-B2 2M

E2A-S08KS02-WP-C2 2M

E2A-S08LS02-WP-B2 2M

E2A-S08LS02-WP-C2 2M

E2A-S08KS02-M1-B2

E2A-S08KS02-M1-C2

E2A-S08LS02-M1-B2

E2A-S08LS02-M1-C2

E2A-M08KS02-M1-B2

E2A-M08KS02-M1-C2

E2A-M08LS02-M1-B2

E2A-M08LS02-M1-C2

E2A-S08KS02-M5-B2

E2A-S08KS02-M5-C2

E2A-S08LS02-M5-B2

E2A-S08LS02-M5-C2

E2A-S08KN04-WP-B2 2M

E2A-S08KN04-WP-C2 2M

E2A-S08LN04-WP-B2 2M

E2A-S08LN04-WP-C2 2M

E2A-S08KN04-M1-B2

E2A-S08KN04-M1-C2

E2A-S08LN04-M1-B2

E2A-S08LN04-M1-C2

E2A-M08KN04-M1-B2

E2A-M08KN04-M1-C2

E2A-M08LN04-M1-B2

E2A-M08LN04-M1-C2

E2A-S08KN04-M5-B2

E2A-S08KN04-M5-C2

E2A-S08LN04-M5-B2

E2A-S08LN04-M5-C2

E2A-S08KS02-WP-B1 2M

E2A-S08KS02-WP-C1 2M

E2A-S08LS02-WP-B1 2M

E2A-S08LS02-WP-C1 2M

E2A-S08KS02-M1-B1

E2A-S08KS02-M1-C1

E2A-S08LS02-M1-B1

E2A-S08LS02-M1-C1

E2A-M08KS02-M1-B1

E2A-M08KS02-M1-C1

E2A-M08LS02-M1-B1

E2A-M08LS02-M1-C1

E2A-S08KS02-M5-B1

E2A-S08KS02-M5-C1

E2A-S08LS02-M5-B1

E2A-S08LS02-M5-C1

E2A-S08KN04-WP-B1 2M

E2A-S08KN04-WP-C1 2M

E2A-S08LN04-WP-B1 2M

E2A-S08LN04-WP-C1 2M

E2A-S08KN04-M1-B1

E2A-S08KN04-M1-C1

E2A-S08LN04-M1-B1

E2A-S08LN04-M1-C1

E2A-M08KN04-M1-B1

E2A-M08KN04-M1-C1

E2A-M08LN04-M1-B1

E2A-M08LN04-M1-C1

E2A-S08KN04-M5-B1

E2A-S08KN04-M5-C1

E2A-S08LN04-M5-B1

E2A-S08LN04-M5-C1

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

27 (40)

49 (62)

27 (43)

49 (65)

27 (43)

49 (65)

27 (39)

49 (61)

27 (40)

49 (62)

27 (43)

49 (65)

27 (43)

49 (65)

27 (39)

49 (61)

Stainless

steel

Stainless

steel

Nickel-

plated

Brass

Stainless

steel

Stainless

steel

Stainless

steel

Nickel-

plated

Brass

Stainless

steel

Pre-wired

M12 connector

M8 connector

(3-pin)

Pre-wired

M12 connector

M8 connector

(3-pin)

2.0 mm

4.0 mm

Shielded

Unshielded

Sensing

distance

Connection Body

material

Thread Length

(overall length)

Output

configuration

Model number

Operation mode NO Operation mode NC

TypeSize

Ordering Information continued (Shaded models are normally stocked.)

E2A-M12KS04-WP-B2 2M

E2A-M12KS04-WP-C2 2M

E2A-M12LS04-WP-B2 2M

E2A-M12LS04-WP-C2 2M

E2A-M12KS04-M1-B2

E2A-M12KS04-M1-C2

E2A-M12LS04-M1-B2

E2A-M12LS04-M1-C2

E2A-M12KN08-WP-B2 2M

E2A-M12KN08-WP-C2 2M

E2A-M12LN08-WP-B2 2M

E2A-M12LN08-WP-C2 2M

E2A-M12KN08-M1-B2

E2A-M12KN08-M1-C2

E2A-M12LN08-M1-B2

E2A-M12LN08-M1-C2

E2A-M18KS08-WP-B2 2M

E2A-M18KS08-WP-C2 2M

E2A-M18LS08-WP-B2 2M

E2A-M18LS08-WP-C2 2M

E2A-M18KS08-M1-B2

E2A-M18KS08-M1-C2

E2A-M18LS08-M1-B2

E2A-M18LS08-M1-C2

E2A-M18KN16-WP-B2 2M

E2A-M18KN16-WP-C2 2M

E2A-M18LN16-WP-B2 2M

E2A-M18LN16-WP-C2 2M

E2A-M18KN16-M1-B2

E2A-M18KN16-M1-C2

E2A-M18LN16-M1-B2

E2A-M18LN16-M1-C2

E2A-M30KS15-WP-B2 2M

E2A-M30KS15-WP-C2 2M

E2A-M30LS15-WP-B2 2M

E2A-M30LS15-WP-C2 2M

E2A-M30KS15-M1-B2

E2A-M30KS15-M1-C2

E2A-M30LS15-M1-B2

E2A-M30LS15-M1-C2

E2A-M30KN20-WP-B2 2M

E2A-M30KN20-WP-C2 2M

E2A-M30LN30-WP-B2 2M

E2A-M30LN30-WP-C2 2M

E2A-M30KN20-M1-B2

E2A-M30KN20-M1-C2

E2A-M30LN30-M1-B2

E2A-M30LN30-M1-C2

E2A-M12KS04-WP-B1 2M

E2A-M12KS04-WP-C1 2M

E2A-M12LS04-WP-B1 2M

E2A-M12LS04-WP-C1 2M

E2A-M12KS04-M1-B1

E2A-M12KS04-M1-C1

E2A-M12LS04-M1-B1

E2A-M12LS04-M1-C1

E2A-M12KN08-WP-B1 2M

E2A-M12KN08-WP-C1 2M

E2A-M12LN08-WP-B1 2M

E2A-M12LN08-WP-C1 2M

E2A-M12KN08-M1-B1

E2A-M12KN08-M1-C1

E2A-M12LN08-M1-B1

E2A-M12LN08-M1-C1

E2A-M18KS08-WP-B1 2M

E2A-M18KS08-WP-C1 2M

E2A-M18LS08-WP-B1 2M

E2A-M18LS08-WP-C1 2M

E2A-M18KS08-M1-B1

E2A-M18KS08-M1-C1

E2A-M18LS08-M1-B1

E2A-M18LS08-M1-C1

E2A-M18KN16-WP-B1 2M

E2A-M18KN16-WP-C1 2M

E2A-M18LN16-WP-B1 2M

E2A-M18LN16-WP-C1 2M

E2A-M18KN16-M1-B1

E2A-M18KN16-M1-C1

E2A-M18LN16-M1-B1

E2A-M18LN16-M1-C1

E2A-M30KS15-WP-B1 2M

E2A-M30KS15-WP-C1 2M

E2A-M30LS15-WP-B1 2M

E2A-M30LS15-WP-C1 2M

E2A-M30KS15-M1-B1

E2A-M30KS15-M1-C1

E2A-M30LS15-M1-B1

E2A-M30LS15-M1-C1

E2A-M30KN20-WP-B1 2M

E2A-M30KN20-WP-C1 2M

E2A-M30LN30-WP-B1 2M

E2A-M30LN30-WP-C1 2M

E2A-M30KN20-M1-B1

E2A-M30KN20-M1-C1

E2A-M30LN30-M1-B1

E2A-M30LN30-M1-C1

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

PNP

NPN

34 (50)

56 (72)

34 (48)

56 (70)

34 (50)

56 (72)

34 (48)

56 (70)

39 (59)

61 (81)

39 (53)

61 (75)

39 (59)

61 (81)

39 (53)

61 (75)

44 (64)

66 (86)

44 (58)

66 (80)

44 (64)

(See note.)

66 (86)

44 (58)

(See note.)

66 (80)

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Nickel-

plated

Brass

Pre-wired

M12 connector

Pre-wired

M12 connector

Pre-wired

M12 connector

Pre-wired

M12 connector

Pre-wired

M12 connector

Pre-wired

M12 connector

4.0 mm

8.0 mm

16.0 mm

15.0 mm

20.0 mm

30.0 mm

20.0 mm

30.0 mm

Shielded

Unshielded

Shielded

Unshielded

Shielded

Unshielded

M12

M18

M30

Sensing

distance

Connection Body

material

Thread Length

(overall length)

Output

configuration

Model number

Operation mode NO Operation mode NC

Note: M30 unshielded Models with double sensing distance and short barrels cannot be mounted due to the necessary separation

distance from the surrounding metal. Standard sensing models are thus available.

TypeSize

Specifications

Size

Type

Item

Sensing distance

Setting distance

Hysteresis

Target

Standard target (mild steel ST37)

Response frequency (See note 1.)

Power supply voltage

(operating voltage range)

Current consumption (DC 3-wire)

Output type

Control output

Indicator

Operation mode

(with sensing object approaching)

Protection circuit

Ambient air temperature

Temperature influence

(See note 2.)

Ambient humidity

Voltage influence

Insulation resistance

Dielectric strength

Vibration resistance

Shock resistance

Standards and listings

Connection method

Weight

(packaged)

Material

Pre-wired model

M12 connector model

Case

Sensing surface

Cable

Clamping nut

Load current

(See note 2.)

Residual voltage

Shielded

E2A-M08S02-M1-B1

E2A-M08S02-M1-B2

E2A-M08S02-M1-C1

E2A-M08S02-M1-C2

E2A-S08S02--B1

E2A-S08S02--B2

E2A-S08S02--C1

E2A-S08S02--C2

2 mm ±10%

0 to 1.6 mm

10% max. of sensing distance

Ferrous metal (The sensing distance decreases with non-ferrous metal.)

12 to 24 VDC. Ripple (p-p): 10% max.

(10 to 32 VDC)

10 mA max.

-B models: PNP open collector

-C models: NPN open collector

200 mA max. (32 VDC max.)

2 V max. (under load current of 200 mA with cable length of 2 m)

Operation indicator (Yellow LED)

-B1/-C1 models: NO

-B2/-C2 models: NC; For details, refer to the timing charts.

Power source circuit reverse polarity protection,

Surge suppressor, Short-circuit protection

Operating: -40°C to 70°C, Storage: -40°C to 85°C (with no icing or condensation)

±10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C

±15% max. of sensing distance at 23°C within temperature range of -40°C to 70°C

Operating: 35% to 95%, Storage: 35% to 95%

±1% max. of sensing distance in rated voltage range ±15%

50 MΩmin. (at 500 VDC) between current carry parts and case

1,000 VAC at 50/60 Hz for 1 min between current carry parts and case

10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y and Z directions

500 m/s2, 10 times each in X, Y and Z directions 1,000 m/s2, 10 times each in X, Y and Z directions

IEC60529: IP67, Degree of protection

EN60947-5-2: EMC

UL (CSA) [E196555] (See note 3.)

-WP models: Pre-wired models (Standard length: 2 m)

-M1 models: M12 4-pin connector models

-M5 models: M8 3-pin connector models

Approx. 65 g Approx. 85 g

M12 connector models: Approx. 20 g Approx. 35 g

M8 connector models: Approx. 15 g

Stainless steel or brass-nickel plated Brass-nickel plated

PBT

PVC

Brass-nickel plated

M8 M12

Unshielded

E2A-M08N04-M1-B1

E2A-M08N04-M1-B2

E2A-M08N04-M1-C1

E2A-M08N04-M1-C2

E2A-S08N04--B1

E2A-S08N04--B2

E2A-S08N04--C1

E2A-S08N04--C2

4 mm ±10%

0 to 3.2 mm

Shielded

E2A-M12S04--B1

E2A-M12S04--B2

E2A-M12S04--C1

E2A-M12S04--C2

4 mm ±10%

0 to 3.2 mm

Unshielded

E2A-M12N08--B1

E2A-M12N08--B2

E2A-M12N08--C1

E2A-M12N08--C2

8 mm ±10%

0 to 6.4 mm

8 x 8 x 1 mm

1,500 Hz

12 x 12 x 1 mm

1,000 Hz

12 x 12 x 1 mm

1,000 Hz

24 x 24 x 1 mm

800 Hz

DC 3-wire Models

Note 1. The response frequency is an average value. Measurement conditions are as follows: standard target, a distance of twice the

standard target distance between targets, and a setting distance of half the sensing distance.

2. When using any model at an ambient temperature between -40°C and -25°C and a power voltage between 30 and 32 VDC,

use a load current of 100 mA max.

3. UL (CSA) [E196555]: Use class 2 circuit only.

Output reverse polarity protection, Power source

circuit reverse polarity protection, Surge suppressor,

Short-circuit protection

Specifications continued

Size

Type

Item

Sensing distance

Setting distance

Hysteresis

Target

Standard target (mild steel ST37)

Response frequency (See note 1.)

Power supply voltage

(operating voltage range)

Current consumption (DC 3-wire)

Output type

Control

output

Indicator

Operation mode (with sensing

object approaching)

Protection circuit

Ambient air temperature

Temperature influence

(See note 2.)

Ambient humidity

Voltage influence

Insulation resistance

Dielectric strength

Vibration resistance

Shock resistance

Standards and listings

Connection method

Weight

(packaged)

Material

Pre-wired model

M12 connector

model

Case

Sensing surface

Cable

Clamping nut

Load current

(See note 2.)

Residual voltage

Shielded

E2A-M18S08--B1

E2A-M18S08--B2

E2A-M18S08--C1

E2A-M18S08--C2

8 mm ±10%

0 to 6.4 mm

10% max. of sensing distance

Ferrous metal (The sensing distance decreases with non-ferrous metal.)

12 to 24 VDC. Ripple (p-p): 10% max.

(10 to 32 VDC)

10 mA max.

-B models: PNP open collector

-C models: NPN open collector

200 mA max. (32 VDC max.)

2 V max. (under load current of 200 mA with cable length of 2 m)

Operation indicator (Yellow LED)

-B1/-C1 models: NO

-B2/-C2 models: NC; For details, refer to the timing charts.

Output reverse polarity protection, Power source circuit reverse polarity protection, Surge suppressor,

Short-circuit protection

Operating: -40°C to 70°C, Storage: -40°C to 85°C (with no icing or condensation)

±10% max. of sensing distance at 23°C within temperature range of -25°C to 70°C

±15% max. of sensing distance at 23°C within temperature range of -40°C to 70°C

Operating: 35% to 95%, Storage: 35% to 95%

±1% max. of sensing distance in rated voltage range ±15%

50 MΩmin. (at 500 VDC) between current carry parts and case

1,000 VAC at 50/60 Hz for 1 min between current carry parts and case

10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y and Z directions

1,000 m/s2, 10 times each in X, Y and Z directions

IEC60529: IP67, Degree of protection

EN60947-5-2: EMC

UL (CSA) [E196555] (See note 3.)

-WP models: Pre-wired models (Standard length: 2 m)

-M1 models: M12 4-pin connector models

-M5 models: M8 3-pin connector models

Approx. 160 g Approx. 280 g Approx. 280 g Approx. 370 g

Approx. 70 g Approx. 200 g Approx. 200 g Approx. 260 g

Brass-nickel plated

PBT

PVC

Brass-nickel plated

M18 M30

Unshielded

E2A-M18N16--B1

E2A-M18N16--B2

E2A-M18N16--C1

E2A-M18N16--C2

16 mm ±10%

0 to 12.8 mm

Shielded

E2A-M30S15--B1

E2A-M30S15--B2

E2A-M30S15--C1

E2A-M30S15--C2

15 mm ±10%

0 to 12 mm

Unshielded

E2A-M30KN20--B1

E2A-M30KN20--B2

E2A-M30KN20--C1

E2A-M30KN20--C2

20 mm ±10%

0 to 16 mm

Unshielded

E2A-M30LN30--B1

E2A-M30LN30--B2

E2A-M30LN30--C1

E2A-M30LN30--C2

30 mm ±10%

0 to 24 mm

24 x 24 x 1 mm

500 Hz

48 x 48 x 1 mm

400 Hz

45 x 45 x 1 mm

250 Hz

60 x 60 x 1 mm

100 Hz

90 x 90 x 1 mm

100 Hz

DC 3-wire Models

Note 1. The response frequency is an average value. Measurement conditions are as follows: standard target, a distance of twice the

standard target distance between targets, and a setting distance of half the sensing distance.

2. When using any model at an ambient temperature between -40°C and -25°C and a power voltage between 30 and 32 VDC,

use a load current of 100 mA max.

3. UL (CSA) [E196555]: Use class 2 circuit only.

Engineering Data

Operating Range (Typical)

Influence of Sensing Object Size and Materials

Engineering Data continued

Operation

PNP Output

Operation mode

Model

E2A---B1

E2A---B2

Timing chart Output circuit

NPN Output

Operation mode

Model

E2A---C1

E2A---C2

Timing chart Output circuit

Dimensions

Pre-wired Models (Shielded) Pre-wired Models (Unshielded)

Note: All units are in millimeters unless otherwise indicated.

Dimensions continued

Pre-wired Models (Shielded) Pre-wired Models (Unshielded)

Note: All units are in millimeters unless otherwise indicated.

Dimensions continued

M12 Connector Models (Shielded) M12 Connector Models (Unshielded)

Note: All units are in millimeters unless otherwise indicated.

Dimensions continued

M8 Connector Models (Shielded) M8 Connector Models (Unshielded)

Note: All units are in millimeters unless otherwise indicated.

Precautions

Type

Shielded

Non-

shielded

Dimension

4.5

–

M12

–

M18

0(See

note 1)

1.5

M30

Short Long

barrel barrel

(See note 2)

30 40

70 90

90 120

30 40

90 120

Safety Precautions

Power Supply

Do not impose an excessive voltage on the E2A, otherwise it

may be damaged. Do not impose AC current (100 to 240

VAC) on any DC model, otherwise it may be damaged.

Load Short-circuit

Do not short-circuit the load, or the E2A may be damaged.

The E2A’s short-circuit protection function will be valid if the

polarity of the supply voltage imposed is correct and within

the rated voltage range.

Wiring

Be sure to wire the E2A and load correctly, otherwise it may

be damaged.

Connection with No Load

Be sure to insert loads when wiring. Make sure to connect a

proper load to the E2A in operation, otherwise it may damage

internal elements.

Do not expose the product to flammable or

explosive gases.

Do not disassemble, repair, or modify the product.

Correct Use

Power Reset Time

The Proximity Sensor is ready to operate within 100 ms after

power is supplied. If power supplies are connected to the

Proximity Sensor and load respectively, be sure to supply

power to the Proximity Sensor before supplying power to

the load.

Effects of Surrounding Metal

When mounting the E2A within a metal panel, ensure that the

clearances given in the following table are maintained.

Power OFF

The Proximity Sensor may output a pulse signal when it is

turned OFF. Therefore, it is recommended that the load be

turned OFF before turning OFF the Proximity Sensor.

Power Supply Transformer

When using a DC power supply, make sure that the DC

power supply has an insulated transformer. Do not use a DC

power supply with an auto-transformer.

Mutual Interference

When installing two or more Sensors face-to-face or side-by-

side, ensure that the minimum distances given in the

following table are maintained.

Note 1. In the case of using the supplied nuts. If true flush mounting

is necessary, apply a free zone of 1.5 mm.

2. In the case of using the supplied nuts. If true flush mounting

is necessary, apply a free zone of 4 mm.

Type

Shielded

Non-

shielded

Dimension

M12

120

100

M18

200

120

M30

Short Long

barrel barrel

110

300 300

200 300

High-tension Lines

Wiring through Metal Conduit:

If there is a power or high-tension line near the cable of the

Proximity Sensor, wire the cable through an independent

metal conduit to prevent against Proximity Sensor damage or

malfunctioning.

Cable Extension

Standard cable length is less than 200 m.

The tractive force is 50 N.

Mounting

The Proximity Sensor must not be subjected to excessive

shock with a hammer when it is installed, otherwise the

Proximity Sensor may be damaged or lose its water-

resistivity.

Do not tighten the nut with excessive force. A washer must

be used with the nut.

Maintenance and Inspection

Periodically perform the following checks to ensure stable

operation of the Proximity Sensor over a long period of time.

1. Check for mounting position, dislocation, looseness, or

distortion of the Proximity Sensor and sensing objects.

2. Check for loose wiring and connections, improper contacts,

and line breakage.

3. Check for attachment or accumulation of metal powder

or dust.

4. Check for abnormal temperature conditions and other

environmental conditions.

5. Check for proper lighting of indicators (for models with a

set indicator.)

Never disassemble or repair the Sensor.

Environment

Water Resistivity

Do not use the Proximity Sensor underwater, outdoors, or in

the rain.

Operating Environment

Be sure to use the Proximity Sensor within its operating

ambient temperature range and do not use the Proximity

Sensor outdoors so that its reliability and life expectancy can

be maintained. Although the Proximity Sensor is water

resistive, a cover to protect the Proximity Sensor from water

or water-soluble machining oil is recommended so that its

reliability and life expectancy can be maintained.

Do not use the Proximity Sensor in an environment with

chemical gas (e.g., strong alkaline or acid gasses including

nitric, chromic, and concentrated sulfuric acid gases).

Inrush Current

Aload that has a large inrush current (e.g., a lamp or motor)

will damage the Proximity Sensor, in which case connect the

load to the Proximity Sensor through a relay.

Precautions continued

Type

M8 Stainless steel type

Brass type

M12

M18

M30

Torque

9 N·m

4 N·m

30 N·m

70 N·m

180 N·m

Wiring

1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed part of all

catalogs, manuals or other documents, whether electronic or in writing, relating to

the sale of goods or services (collectively, the "Goods") by Omron Electronics LLC

and its subsidiary companies (“Seller”). Seller hereby objects to any terms or

conditions proposed in Buyer’s purchase order or other documents which are

inconsistent with, or in addition to, these Terms. Please contact your Omron

representative to confirm any additional terms for sales from your Omron company.

2. Prices. All prices stated are current, subject to change without notice by Seller. Buyer

agrees to pay the price in effect at time of shipment.

3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices sent

to Buyer after deducting transportation charges, taxes and duties, and will be allowed

only if (i) the invoice is paid according to Seller’s payment terms and (ii) Buyer has

no past due amounts owing to Seller.

4. Orders. Seller will accept no order less than $200 net billing.

5. Governmental Approvals. Buyer shall be responsible for, and shall bear all costs

involved in, obtaining any government approvals required for the importation or sale

of the Goods.

6. Taxes. All taxes, duties and other governmental charges (other than general real

property and income taxes), including any interest or penalties thereon, imposed

directly or indirectly on Seller or required to be collected directly or indirectly by

Seller for the manufacture, production, sale, delivery, importation, consumption or

use of the Goods sold hereunder (including customs duties and sales, excise, use,

turnover and license taxes) shall be charged to and remitted by Buyer to Seller.

7. Financial. If the financial position of Buyer at any time becomes unsatisfactory to

Seller, Seller reserves the right to stop shipments or require satisfactory security or

payment in advance. If Buyer fails to make payment or otherwise comply with these

Terms or any related agreement, Seller may (without liability and in addition to other

remedies) cancel any unshipped portion of Goods sold hereunder and stop any

Goods in transit until Buyer pays all amounts, including amounts payable hereunder,

whether or not then due, which are owing to it by Buyer. Buyer shall in any event

remain liable for all unpaid accounts.

8. Cancellation; Etc. Orders are not subject to rescheduling or cancellation unless Buyer

indemnifies Seller fully against all costs or expenses arising in connection therewith.

9. Force Majeure. Seller shall not be liable for any delay or failure in delivery resulting

from causes beyond its control, including earthquakes, fires, floods, strikes or other

labor disputes, shortage of labor or materials, accidents to machinery, acts of

sabotage, riots, delay in or lack of transportation or the requirements of any

government authority.

10.Shipping; Delivery. Unless otherwise expressly agreed in writing by Seller:

a. Shipments shall be by a carrier selected by Seller;

b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall

constitute delivery to Buyer;

c. All sales and shipments of Goods shall be FOB shipping point (unless otherwise

stated in writing by Seller), at which point title to and all risk of loss of the Goods

shall pass from Seller to Buyer, provided that Seller shall retain a security interest

in the Goods until the full purchase price is paid by Buyer;

d. Delivery and shipping dates are estimates only.

e. Seller will package Goods as it deems proper for protection against normal

handling and extra charges apply to special conditions.

11.Claims. Any claim by Buyer against Seller for shortage or damage to the Goods

occurring before delivery to the carrier must be presented in writing to Seller within

30 days of receipt of shipment and include the original transportation bill signed by

the carrier noting that the carrier received the Goods from Seller in the condition

claimed.

12.Warranties. (a) Exclusive Warranty. Seller’s exclusive warranty is that the Goods will

be free from defects in materials and workmanship for a period of twelve months

from the date of sale by Seller (or such other period expressed in writing by Seller).

Seller disclaims all other warranties, express or implied. (b) Limitations. SELLER

MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE OF THE GOODS. BUYER ACKNOWLEDGES THAT IT ALONE HAS

DETERMINED THAT THE GOODS WILL SUITABLY MEET THE REQUIREMENTS OF

THEIR INTENDED USE. Seller further disclaims all warranties and responsibility of

any type for claims or expenses based on infringement by the Goods or otherwise of

any intellectual property right. (c) Buyer Remedy. Seller’s sole obligation hereunder

shall be to replace (in the form originally shipped with Buyer responsible for labor

charges for removal or replacement thereof) the non-complying Good or, at Seller’s

election, to repay or credit Buyer an amount equal to the purchase price of the Good;

provided that in no event shall Seller be responsible for warranty, repair, indemnity or

any other claims or expenses regarding the Goods unless Seller’s analysis confirms

that the Goods were properly handled, stored, installed and maintained and not

subject to contamination, abuse, misuse or inappropriate modification. Return of any

goods by Buyer must be approved in writing by Seller before shipment. Seller shall

not be liable for the suitability or unsuitability or the results from the use of Goods in

combination with any electrical or electronic components, circuits, system

assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as

an amendment or addition to the above warranty.

13.Damage Limits; Etc. SELLER SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR

CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE GOODS, WHETHER SUCH

CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Seller exceed the individual price of the Good on

which liability is asserted.

14.Indemnities. Buyer shall indemnify and hold harmless Seller, its affiliates and its

employees from and against all liabilities, losses, claims, costs and expenses

(including attorney's fees and expenses) related to any claim, investigation, litigation

or proceeding (whether or not Seller is a party) which arises or is alleged to arise

from Buyer's acts or omissions under these Terms or in any way with respect to the

Goods. Without limiting the foregoing, Buyer (at its own expense) shall indemnify

and hold harmless Seller and defend or settle any action brought against Seller to the

extent that it is based on a claim that any Good made to Buyer specifications

infringed intellectual property rights of another party.

15.Property; Confidentiality. The intellectual property embodied in the Goods is the

exclusive property of Seller and its affiliates and Buyer shall not attempt to duplicate

it in any way without the written permission of Seller. Notwithstanding any charges to

Buyer for engineering or tooling, all engineering and tooling shall remain the

exclusive property of Seller. All information and materials supplied by Seller to Buyer

relating to the Goods are confidential and proprietary, and Buyer shall limit

distribution thereof to its trusted employees and strictly prevent disclosure to any

third party.

16.Miscellaneous. (a) Waiver. No failure or delay by Seller in exercising any right and no

course of dealing between Buyer and Seller shall operate as a waiver of rights by

Seller. (b) Assignment. Buyer may not assign its rights hereunder without Seller's

written consent. (c) Amendment. These Terms constitute the entire agreement

between Buyer and Seller relating to the Goods, and no provision may be changed or

waived unless in writing signed by the parties. (d) Severability. If any provision hereof

is rendered ineffective or invalid, such provision shall not invalidate any other

provision. (e) Setoff. Buyer shall have no right to set off any amounts against the

amount owing in respect of this invoice. (f) As used herein, “including” means

“including without limitation”.

Certain Terms and Conditions of Sale

1. Suitability of Use. Seller shall not be responsible for conformity with any standards,

codes or regulations which apply to the combination of the Good in the Buyer’s

application or use of the Good. At Buyer’s request, Seller will provide applicable third

party certification documents identifying ratings and limitations of use which apply to

the Good. This information by itself is not sufficient for a complete determination of

the suitability of the Good in combination with the end product, machine, system, or

other application or use. The following are some examples of applications for which

particular attention must be given. This is not intended to be an exhaustive list of all

possible uses of this Good, nor is it intended to imply that the uses listed may be

suitable for this Good:

(i) Outdoor use, uses involving potential chemical contamination or electrical

interference, or conditions or uses not described in this document.

(ii) Energy control systems, combustion systems, railroad systems, aviation systems,

medical equipment, amusement machines, vehicles, safety equipment, and

installations subject to separate industry or government regulations.

(iii) Systems, machines and equipment that could present a risk to life or property.

Please know and observe all prohibitions of use applicable to this Good.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO

LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS

BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE SELLER’S PRODUCT IS

PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL

EQUIPMENT OR SYSTEM.

2. Programmable Products. Seller shall not be responsible for the user’s programming

of a programmable Good, or any consequence thereof.

3. Performance Data. Performance data given in this catalog is provided as a guide for

the user in determining suitability and does not constitute a warranty. It may

represent the result of Seller’s test conditions, and the user must correlate it to actual

application requirements. Actual performance is subject to the Seller’s Warranty and

Limitations of Liability.

4. Change in Specifications. Product specifications and accessories may be changed at

any time based on improvements and other reasons. It is our practice to change part

numbers when published ratings or features are changed, or when significant

construction changes are made. However, some specifications of the Good may be

changed without any notice. When in doubt, special part numbers may be assigned

to fix or establish key specifications for your application. Please consult with your

Seller’s representative at any time to confirm actual specifications of purchased

Good.

5. Errors and Omissions. The information in this catalog has been carefully checked and

is believed to be accurate; however, no responsibility is assumed for clerical,

typographical or proofreading errors, or omissions.

Certain Precautions on Specifications and Use

OMRON ELECTRONICS LLC

One Commerce Drive

Schaumburg, IL 60173

847-843-7900

For US technical support or other inquiries:

800-556-6766

OMRON CANADA, INC.

885 Milner Avenue

Toronto, Ontario M1B 5V8

416-286-6465

OMRON ON-LINE

Global - http://www.omron.com

USA - http://www.omron.com/oei

Canada - http://www.omron.ca

Cat. No. D096-E3-01 12/03 Specifications subject to change without notice Printed in USA

Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s

website at www.omron.com/oei - under the “About Us” tab in the Legal Matters section.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.