FUJITSU MICROELECTRONICS DATA SHEET DS04-27269-1E ASSP for Power Management Applications 1ch DC/DC converter IC with synchronous rectification MB39A130A DESCRIPTION MB39A130A is a 1ch step-down DC/DC converter equipped with a bottom detection comparator and N-ch/N-ch synchronous rectification. It supports low on-duty operation to allow stable output of low voltages when there is a large difference between input and output voltages. MB39A130A realizes ultra-rapid response and high efficiency with built-in enhanced protection features. FEATURES * * * * * * * * * * * * * * * * * Power conversion efficiency : 96% (Max.) Adjustable frequency setting by an external resistor : 100 kHz to 600 kHz High accuracy reference voltage : 1.0% Output voltage setting range : 0.7 V to 5 V or fixed to 1.2 V/2.5 V Adjustable output voltages setting by the external control : 4.5 V to 25 V Input voltage range (VIN) Inductor saturation detection function which can be set optional Built-in over voltage protection function Built-in under voltage protection function Built-in over current protection function Built-in Power-Good detection function Built-in over temperature protection function Built-in soft-start circuit without load dependence Built-in discharge control circuit Built-in synchronous rectification type output driver for N-ch MOS FET Standby current : 0 [A] (Typ) Small package : TSSOP-24 (4.4 x 6.5 [mm]) APPLICATIONS * * * * * Digital TV Photocopiers STB BD, DVD players/recorders Projectors Various other advanced devices Copyright(c)2009 FUJITSU MICROELECTRONICS LIMITED All rights reserved 2009.1 MB39A130A PIN ASSIGNMENT (TOP VIEW) GND : 1 24 : FB REFIN : 2 23 : VO VREF : 3 22 : RT CS : 4 21 : CB COVP : 5 20 : OUT-1 CUVP : 6 19 : LX TSSOP-24 PGOOD : 7 18 : VBIN CTL : 8 17 : VCC LSAT : 9 16 : VB ILIM : 10 15 : OUT-2 +INC : 11 14 : PGND -INC : 12 13 : FSW (FPT-24P-M08) 2 DS04-27269-1E MB39A130A PIN DESCRIPTIONS Pin No. Pin Name I/O 1 GND 2 REFIN I Reference voltage input pin for Error Comp. 3 VREF O Reference voltage output pin. 4 CS I Soft-start time setting capacitor connection pin. 5 COVP Detection time setting capacitor connection pin for OVP function. The OVP function can be disabled by a short circuit with GND pin. 6 CUVP Detection time setting capacitor connection pin for UVP function. The UVP function can be disabled by a short circuit with GND pin. 7 PGOOD O Power-Good detection circuit output pin. (Open-drain output) 8 CTL I Power supply control pin. IC changes to standby state when CTL is set to "L" level. 9 LSAT I Inductor oversaturation detection level setting voltage input pin. 10 ILIM I Over current detection level setting voltage input pin. 11 +INC I Current detection block (Current Sense) input pin. 12 -INC I Current detection block (Current Sense) input pin. 13 FSW I Preset value switching pin for operating frequency. 14 PGND Ground pin for output circuit. 15 OUT-2 O Output pin for external low-side FET gate drive. 16 VB O Bias output pin for output circuit. 17 VCC Power supply pin. 18 VBIN I 19 LX Inductor and external high-side FET source and external low-side FET drain connection pin. 20 OUT-1 O Output pin for external high-side FET gate drive. 21 CB Connection pin for boot strap capacitor. It connects a capacitor between CB and LX pins. 22 RT Connection pin for tON time setting resistor. 23 VO I Input pin for DC/DC output voltage. 24 FB I Feedback pin for DC/DC output voltage. DS04-27269-1E Description Ground pin. Bias voltage external input pin for output circuit and control circuit. 3 MB39A130A BLOCK DIAGRAM FSW RT 22 VCC 13 17 VBIN 18 <Discharge > CTL uvp otp VB VB Reg. <Soft-Start > VREF 5 A CTL, uvlo CS 16 (5 V) tON Generator ON/OFF (4.5 V) CB 4 21 VO OUT-1 23 <Error Comp.> Drv-1 LX Drive Logic VO REFIN Control FB 20 19 OUT-2 24 Drv-2 15 2 REFIN INTREF PGND +INC -INC 14 11 12 Current Sense <LSAT Comp.> LSAT 9 10 A 9:1 <ILIM Comp.> ILIM VB 9:1 <UVLO> H:UVLO release 10 VB UVLO 5 A 5 VREF UVLO <OVP Comp.> COVP S Q R VB INTREF x 1.15 V CUVP PGOOD 7 5 A 6 <UVP Comp.> S Q R INTREF x 0.7 V VCC ON/OFF bias INTREF x 0.9 V <PGOOD Comp.> <REF><CTL> CTL 8 (2.5 V) 3 VREF 4 1 GND DS04-27269-1E MB39A130A ABSOLUTE MAXIMUM RATINGS Parameter Symbol Condition Power supply voltage VCC CB pin input voltage Rating Unit Min Max 27 V VCB 32 V Voltage between CB and LX VCBLX 7 V Bias external input voltage VBIN 7 V VI CTL pin 27 V VI FB, VO, REFIN, FSW pins VB + 0.3 V V+INC 27 V V-INC 27 V VILIM VB + 0.3 V VLSAT VB + 0.3 V PGOOD pin voltage VPG 7 V Output current IOUT DC 60 mA Power dissipation PD Ta + 25C 1315 mW -55 +125 C Control input voltage Input voltage Storage temperature TSTG WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. DS04-27269-1E 5 MB39A130A RECOMMENDED OPERATING CONDITIONS Parameter Symbol Condition Power supply voltage VCC CB pin input voltage Value Unit Min Typ Max 4.5 25.0 V VCB 30 V Reference voltage output current IREF -100 0 A Bias output current IVB -1 mA CTL pin input voltage VI CTL pin 0 25 V VI FB, VO, REFIN, FSW pins 0 VB V V+INC -0.3 + 2.9 V V-INC -0.3 + 25 V VILIM 0 VB V VLSAT 0 VB V PGOOD pin output voltage VPG 0 5.5 V PGOOD pin output current IPG 0 4 mA Peak output current IOUT -1200 + 1200 mA Operation frequency range fOSC 100 450 780 kHz Timing resistor RT 43 k Current detection resistor RS 10 m Soft start capacitor CS 0.018 F CB pin capacitor CCB 0.1 F Reference voltage output capacitor CREF 0.01 1.0 F Bias voltage output capacitor CVB 2.2 10 F Operating ambient temperature Ta -30 + 25 + 85 C Input voltage Duty 5% (t = 1/fOSC x Duty) WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. 6 DS04-27269-1E MB39A130A ELECTRICAL CHARACTERISTICS Parameter Reference Voltage Block [REF] Bias Voltage Block [VB Reg.] Output voltage VREF Load stability Load Short-circuit output current Output voltage Inside/Outside switching threshold Switch (SW) resistor Under voltage Threshold voltage Lockout Hysteresis width Protection Circuit Block Threshold voltage [UVLO] Hysteresis width Soft-Start/ Discharge Block [Soft-Start/ Discharge] Symbol Charge current Electrical discharge resistance Discharge end voltage ON time ON time (Preset value 1) ON/OFF Time ON time (Preset value 2) Generator Block [tON Generator] Minimum OFF time RT external condition Preset value 1 condition Preset value 2 condition Input current (Ta = +25C, VCC pin = 15 V, CTL pin = 5 V, VREF pin = 0 mA) Value Pin Condition Unit No. Min Typ Max 3 2.463 2.500 2.537 V VREF pin = 0 A to 3 1 10 mV -100 A IOS 3 VREF pin = 0 V -20 -10 -5 mA VB VTLH VTHL 16 18 18 VBIN pin VBIN pin 4.9 4.3 4.1 5.0 4.5 4.3 5.1 4.7 4.5 V V V RSW 18 VBIN pin = 5 V 4*1 VTLH VTHL VH VTLH VTHL VH 16 16 16 3 3 3 3.8 3.1 1.8 1.6 4.0 3.3 0.7*1 2.0 1.8 0.2*1 4.2 3.5 2.2 2.0 V V V V V V ICS 4 -6.3 -4.5 -3.1 A RD 23 VB pin VB pin VB pin VREF pin VREF pin VREF pin CTL pin = 5 V, CS pin = 0 V CTL pin = 0 V, VO pin 0.3 V 16*1 VO 23 0.3*1 V 246 280 314 ns 272 390 508 ns 142 220 298 ns 360 480 600 ns 1.5 V CTL pin = 0 V tON 20 tON_2 20 tON_3 20 tOFF 20 RT pin = 43 k, FSW pin = GND pin, VCC pin = 15 V, VO pin = 1.5 V RT pin = VB pin, FSW pin = VREF pin, VCC pin = 15 V, VO pin = 1.5 V RT pin = FSW pin = VB pin, VCC pin = 15 V, VO pin = 1.5 V VFSW1 13 FSW pin 0 VFSW2 13 FSW pin 1.5 VFSW 13 FSW pin VB-1.5 VB V IFSWL IFSWM IFSWH 13 13 13 FSW pin = 0 V FSW pin = VREF pin FSW pin = VB pin -10 -1 -5 0 5 +1 10 A A A VREF VB-1.5 V (Continued) DS04-27269-1E 7 MB39A130A (Ta = +25C, VCC pin = 15 V, CTL pin = 5 V, VREF pin = 0 mA) Parameter Symbol Pin No. VO1 23 VO2 VFB1 Value Condition Unit Min Typ Max REFIN pin = GND pin, FB pin = VB pin 1.172 1.190 1.208 V 23 REFIN pin = VB pin, FB pin = VB pin 2.453 2.490 2.527 V 24 REFIN pin = GND pin 0.693 0.700 0.707 V VFB1T 24 REFIN pin = GND pin* , Ta = -20C to +70C 0.689*2 0.700 0.711*2 V VFB2 24 REFIN pin = VB pin 1.442 1.457 1.472 V VFB2T 24 REFIN pin = VB pin*3, Ta = -20C to +70C 1.435*2 1.457 1.479*2 V IREFIN 2 REFIN pin = 0.6 V -0.5 0 +0.5 A FB input current IFB 24 FB pin = 0.7 V -0.5 0 +0.5 A VO input current IVO 23 VO pin = 2 V 17.0 24.3 A VTH1 24,2 REFIN, FB pins: Hi-side 2.4 2.5 V VTH2 2 REFIN pin: Lo-side 0.3 0.4 V -1.0 -0.3 A Output bottom detection voltage 3 Output Voltage Setting Block [VO REFIN Control, Error Comp.] Feedback voltage REFIN input current Threshold voltage Current Detection Block Input current [ Current Sense ] Over Current Detection Block [ ILIM Comp. ] Inductor Saturation Detection Block [LSAT Comp.] IINC 11,12 +INC, -INC pins = 0 VTH (+INC pin) - (-INC pin) 11,12 ILIM pin = 5 V Internally fixed value 40 50 60 mV VTH2 (+INC pin) - (-INC pin) 11,12 ILIM pin = 1.0 V Externally fixed value 90 100 110 mV Current limit setting value Input current IILIM 10 ILIM pin = 0 V -1 0 +1 A Threshold voltage VTH3 10 ILIM pin 3.5 3.7 V Oversaturation detection setting value VTH 11,12 (+INC pin) - (-INC pin) LSAT pin = 2.0 V 180 200 220 mV Input current ILSAT 9 LSAT pin = 0 V -1 0 +1 A LSAT pin sink current at detection of oversaturation ILSAT2 9 LSAT pin = 1 V 7.7 10.0 14.3 A (Continued) 8 DS04-27269-1E MB39A130A (Ta = +25C, VCC pin = 15 V, CTL pin = 5 V, VREF pin = 0 mA) Symbol Pin No. Over-voltage detecting voltage VOVP 24 Charge current ICOVP 5 Threshold voltage VTH 5 COVP pin on-resistance RCOVP 5 Under-voltage detecting voltage VUVP 24 Charge current ICUVP 6 Threshold voltage VTH 6 CUVP pin on-resistance RCUVP 6 Threshold voltage VTHL 24 Hysteresis width VH Output leak current "L" level output voltage Parameter Over-voltage Protection Circuit Block [OVP Comp.] Under-voltage Protection Circuit Block [UVP Comp.] Power-Good Detection Circuit Block [PGOOD Comp.] Over-temperature Protection Protection Circuit temperature Block [OTP] Condition Value Unit Min Typ Max INTREF x 1.12 INTREF x 1.15 INTREF x 1.18 V -7.7 -5.5 -4.1 A VB x 0.5 V 1.1*1 k INTREF x 0.65 INTREF x 0.70 INTREF x 0.75 V -7.7 -5.5 -4.1 A VB x 0.5 V 1.1*1 k Error Comp. input INTREF x 0.87 INTREF x 0.90 INTREF x 0.93 V 24 Error Comp. input INTREF x 0.02*1 V ILEAK 7 PGOOD pin = 5 V 0 1 A VOL 7 PGOOD pin = 1 mA 0.1 0.4 V TOTPH +150*1 C TOTPL +125*1 C Error Comp. input COVP pin Error Comp. input CUVP pin (Continued) DS04-27269-1E 9 MB39A130A (Continued) (Ta = +25C, VCC pin = 15 V, CTL pin = 5 V, VREF pin = 0 mA) Symbol Pin No. Condition High-side output on-resistance ROH 20 ROL Low-side output on-resistance Parameter Output Block [Drv-1, Drv-2] Output source current Typ Max OUT-1 pin = - 100 mA 4 7 20 OUT-1 pin = 100 mA 1.0 3.5 ROH 15 OUT-2 pin = -100 mA 4 7 ROL 15 OUT-2 pin = 100 mA 1.0 3.5 -0.5*1 A 0.9*1 A ISOURCE LX pin = 0 V, CB pin = 5 V, 15,20 OUT-1, OUT-2 pins = 2.5 V, Duty 5% ISINK1 20 ISINK2 15 OUT-2 pin = 2.5 V, Duty 5% 1.8*1 A Dead time TD 15,20 LX pin = 0 V, CB pin = 5 V 50*1 ns ON condition VON 8 2 25 V OFF condition VOFF 8 0 0.8 V ICTLH 8 CTL pin = 5 V 25 40 A ICTLL 8 CTL pin = 0 V 0 1 A ICCS 17 CTL pin = 0 V 0 10 A 17 CTL pin = 5 V, REFIN pin = GND pin, LX pin = 0 V, FB pin = 1.0 V 1.3 2.2 mA 17 CTL pin = 5 V, LX pin = 0 V, FB pin = 1.0 V, VBIN pin = 5 V 130 220 A Input current Standby current ICC1 General Unit Min LX pin = 0 V, CB pin = 5 V, OUT-1 pin = 2.5 V, Duty 5% Output sink current Control Block [CTL] Value Power-supply current ICC2 *1: This parameter is not be specified. This should be used as a reference to support designing the circuits. *2: This parameter is guaranteed by design, which is not supported by a final test. *3: For the measurement circuit, see the " DIAGRAM OF FEEDBACK VOLTAGE MEASUREMENT CIRCUIT". 10 DS04-27269-1E MB39A130A DIAGRAM OF FEEDBACK VOLTAGE MEASUREMENT CIRCUIT * VFB1,VFB2 VO 23 <<Error Comp.>> 30 k FB 24 VFB1 VFB2 VM VREF <<Amp>> 30 k VFB1 VFB2 INTREF DS04-27269-1E 11 MB39A130A TYPICAL CHARACTERISTICS 1400 1315 1200 VREF bias voltage vs. Operating ambient temperature 2.5375 VREF bias voltage VVREF (V) Power dissipation PD (mW) Power dissipation vs. Operating ambient temperature 1000 800 600 400 200 0 -50 -25 0 2.5125 2.5000 2.4875 2.4750 2.4625 -40 -20 +25 +50 +75 +100 +125 IVREF = 0 A 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) Operating ambient temperature Ta (C) Error Comp. threshold voltage vs. Operating ambient temperature Error Comp. threshold voltage vs. Operating ambient temperature 0.707 1.472 Error Comp. threshold voltage EVTH2 (V) Error Comp. threshold voltage EVTH1 (V) 2.5250 0.705 0.703 0.701 0.699 0.697 0.695 0.693 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) 1.467 1.462 1.457 1.452 1.447 1.442 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) (Continued) 12 DS04-27269-1E MB39A130A VB bias voltage vs. Operating ambient temperature VB bias voltage vs. VB bias output current 6.0 5.10 VB bias voltage VVB (V) VB bias voltage VVB (V) 5.5 5.05 5.00 4.95 IVB = 0 A 4.90 -40 -20 0 4.5 VCC = 5 V 4.0 3.5 3.0 VCC = 4.5 V 2.5 Ta = +25C 2.0 -0.03 +20 +40 +60 +80 +100 -0.02 -0.02 -0.01 -0.01 Operating ambient temperature Ta (C) VB bias output current IVB (A) DRVH on time vs. Timing resistor value DRVH on time vs. Operating ambient temperature 760 DRVH on time tON (ns) VCC = 15 V VO = 1.5 V FSW = GND Ta = +25C 980 540 320 100 0 320 1200 DRVH on time tON (ns) VCC = 6 V 5.0 20 50 80 110 140 Timing resistor value RRT (k) 170 VCC = 15 V VO = 1.5 V RT = 43 k FSW = GND 300 280 260 240 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) (Continued) DS04-27269-1E 13 MB39A130A DRVH on time vs. Operating ambient temperature DRVH on time vs. Operating ambient temperature 490 390 290 DRVH Minimum off time toffmin (ns) 190 -40 -20 0 DRVH on time tON_3 (ns) 320 VCC =15 V VO = 1.5 V RT=VB FSW = VREF VCC = 15 V VO = 1.5 V RT = VB FSW = VB 270 220 170 120 -40 +20 +40 +60 +80 +100 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) Operating ambient temperature Ta (C) DRVH Minimum off time vs. Operating ambient temperature DRVH Minimum off time vs. Input voltage 600 560 520 480 440 400 360 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) DRVH Minimum off time toffmin (ns) DRVH on time tON_2 (ns) 590 600 560 520 480 440 400 Ta = +25C 360 0 5 10 15 20 25 Input voltage VIN (V) (Continued) 14 DS04-27269-1E MB39A130A (Continued) Dead time vs. Operating ambient temperature Dead time tD (ns) 100 75 tD1 50 tD2 25 0 -40 -20 0 +20 +40 +60 +80 +100 Operating ambient temperature Ta (C) DS04-27269-1E 15 MB39A130A FUNCTION Bottom detection comparator system The bottom detection comparator system uses fixed ON time (tON) and the switching ripple voltage which superimposed the output voltage (VO), instead of a certain triangular waveform. The tON time is uniquely defined by the power supply voltage (VIN) and the output voltage (VO). During the tON period, a current is supplied from the power supply voltage (VIN). This results in an increased inductor current (ILX). And also an increased output voltage (VO) due to the parasitic resistance (ESR) of the output capacitor. And when the tOFF period arrives, the energy accumulated in the inductor is supplied to the load to decrease the inductor current (ILX) gradually. Consequently, the output voltage (VO), which has been increasing due to the parasitic resistance (ESR) of the output capacitor, also decreases. When the output voltage goes below a certain VREF potential, SR-FF is set and the tON period comes back. Switching is repeated as described above. Error Comp. is used to compare the reference voltage (VREF) with the output voltage (VO) to control the off-duty condition in order to stabilize the output voltage. Bottom Detection Comparator Model VIN tON time setting circuit Error Comp. + VREF - R S Q ILX VO SR-FF ESR VO VREF tOFF tON 16 DS04-27269-1E MB39A130A (1) Reference Voltage Block (REF) The reference voltage block (REF) generates a temperature-compensated stable voltage (2.5 V Typ) based on the voltage supplied from the VCC pin (Pin 17). It is used as the reference power supply for the IC's internal circuit. The reference voltage is output from the VREF pin (Pin 3), and up to 100 A can be supplied to the outside as the maximum load current. (2) Under Voltage Lockout Protection Circuit Block (UVLO) A bias voltage (VB), a transitional state at startup, or a sudden drop in an internal reference voltage (VREF) leads to malfunction of the control IC, causing system destruction/deterioration. To prevent such malfunction, the under voltage lockout protection circuit detects a voltage drop at the VB pin (Pin 16) or the VREF pin (Pin 3) and fixes the OUT-1 pin (Pin 20) and the OUT-2 pin (Pin 15) to the "L" level. When voltages at the VB pin and the VREF pin exceed the threshold voltage of the under voltage lockout protection circuit, the system is restored. Table of Protection Circuit (VB-UVLO, VREF-UVLO) Operation Functions The logics of the following pins are fixed during UVLO operation (when VB and VREF voltages are below the UVLO threshold voltage). OUT-1 OUT-2 CS OVP UVP L L L Latch reset COVP = L Latch reset CUVP = L (3) Soft-start Block (Soft-Start) It prevents a rush current or an output voltage (VO) overshooting at the output start. It prevents a rush current at start-up by connecting a capacitor to the CS pin (Pin 4). When the CTL pin (Pin 8) is set to the "H" level, the capacitor connected to the CS pin starts charging and its lamp voltage is input to the error comparator (Error Comp.). This allows for the setting of the soft-start time that does not depend on the output load of the DC/DC converter. (4) Discharge Block (Discharge) It discharges electrical charges stored in a smoothing capacitor at output stop. When the CTL pin (Pin 8) is set to the "L" level, the OUT-1 pin (Pin 20) and the OUT-2 pin (Pin 15) are set to the "L" level and turn on the discharging FET (RON 16 ) which is connected between the VO pin (Pin 23) and GND. When the voltage at the VO pin falls below 0.3 V, the discharging FET is turned off and the IC changes to standby state. The discharge function also operates after the under-voltage protection circuit block (UVP Comp.) is latched or when the over-temperature protection circuit block is in operation. DS04-27269-1E 17 MB39A130A (5) ON/OFF Time Generator Block (tON Generator) The ON time generator block (tON Generator, ON ONE-SHOT) has a built-in capacitor for timing setting. When the FSW pin (Pin 13) is connected to GND, ON time that is dependent on the input voltage is generated by connecting a timing setting resistor to the RT pin (Pin 22). VO VCC tON = tON RT VCC VO x RT x 0.059 + 30 : ON time on high-side FET [ns] : Timing resistor value [] : Power supply voltage [V] : Output voltage [V] If the VO1 and VO2 voltages are 0.1 V or less at soft-start, it is fixed in a value at 0.1V in VO1 and VO2 in ON time. In addition, the FSW pin can be used to switch the ON time setting between the setting by the resistor that is externally connected to the RT pin and the setting by the IC's internal resistor. The OFF time generator block (OFF ONE-SHOT) generates 480[ns] (Typ) as the minimum OFF time. tOFF = ( tON VCC VO 18 VCC VO - 1) x tON : ON time on high-side FET [ns] : Power supply voltage [V] : Output voltage [V] DS04-27269-1E MB39A130A (6) Output Voltage Setting Block (VO REFIN Control, Error Comp.) The output voltage setting block (VO REFIN Control, Error Comp.) supports the setting of various output voltages according to connecting destination or the external circuit of the REFIN pin (Pin 2) and the FB pin (Pin 24). FB 24 23 Comp.1 VO SW1 SW2 2.5V Error Comp. REFIN SW3 2 INTREF Comp.2 SW4 SW5 1.46V 0.7V 2.5V Comp.3 0.3V Output Voltage Setting Table REFIN FB SW state INTREF (Internal reference voltage) GND VB SW2,5:ON, SW1,3,4:OFF 0.7 V (Typ) VO = 1.2 V set (internal setting) VB VB SW2,4:ON, SW1,3,5:OFF 1.46 V (Typ) VO = 2.5 V set (internal setting) 0.7 V (Typ) Internal reference voltage fixed to 0.7 V, output voltage setting discretionary by external resistor value ratio between VO-FB and FB-GND 1.457 V (Typ) Internal reference voltage fixed to 1.457 V, output voltage setting discretionary by external resistor value ratio between VO-FB and FB-GND GND VB 0.7 V 1.457 V 0.5 V to 2.2 V VB SW1,5:ON, SW2,3,4:OFF SW1,4:ON, SW2,3,5:OFF SW2,3:ON, SW1,4,5:OFF Remarks Output setting is reference voltage setting discretionary by external = REFIN pin voltage resistor value ratio between VREFREFIN and REFIN -GND, by built-in feedback resistor used Error Comp. detects the end timing of the OFF period by comparing the non-inverting input and inverting input. In other words, it detects that the output voltage has fallen below the output setting voltage, and puts the output in ON state. In this case, the delay time is 100 ns (Typ). DS04-27269-1E 19 MB39A130A (7) Current Detection Block (Current Sense) This circuit is used to detect a inductor current (IL). The current detection block (Current Sense) converts a voltage waveform between the +INC pin (Pin 11) and the -INC pin (Pin 12) into the GND-standard voltage waveform. Therefore, it can detect a ripple current of the inductor by the current sense resistor RS connected between the +INC and -INC pins. (8) Over Current Detection Block (ILIM Comp.) Comparing the current value of the current sense resistor and the setting value of over current detection starts the over current protection operation. The over current detection block (ILIM Comp.) compares the output voltage waveform in the current detection block and the over current detection level which is 1/10 of the voltage externally set to the ILIM pin (Pin 10). The over current detection block detects the bottom value of the ripple current which flows into the inductor. The OFF state has been kept until the output voltage waveform in the current detection block goes down below the over current detection level, and the ON state of the high-side FET is permitted when the waveform goes down below the level. This is the protection operation against the over current. The protection operation is the operation which drops the output voltage. Moreover, the over current detection level can be set to a fixed value (50 mV Typ) by applying 3.8 V (Typ) or more voltage to the ILIM pin. * Current detection block / Over current detection block IL ILripple Inductor Current (IL) ILOAD LOAD L IL(peak) RS IL(bottom) t -INC +INC 12 11 Current Sence ILIM Comp. ILIM to Drive Logic 10 9:1 Rs: Current sense resistor 20 DS04-27269-1E MB39A130A (9) Inductor Saturation Detection Block (LSAT Comp.) As an auxiliary function for over current protection, this circuit prevents the occurrence of excessive currents due to magnetic saturation of the inductor. The inductor saturation detection block (LSAT Comp.) compares the output voltage waveform of the current detection block (Current Sense) with 1/10 of the saturation detection level of the voltage externally set to the LSAT pin (Pin 9) and detects the peak value of the ripple current that flows to the inductor. During the ON period of high-side FET, the output voltage waveform of the current detection block exceeds the saturation detection level, immediately after it detected that it sets an OFF-state. Simultaneously, it also sets an SR latch in LSAT Comp. and sinks 10 A (Typ) of a constant current from the LSAT pin. This SR latch is reset in every cycle and the same operation is repeated. The saturation detection level goes down by sinking the electric charge of the capacitor connected to the LSAT pin in every cycle. Depending on the external parts or use conditions, the ILIM and LSAT pins must be set to various voltages; therefore, the detection level can be set freely by the external resistor value ratio. Moreover, the saturation detection function can be disabled by applying 3.8 V (Typ) or more voltage to the LSAT pin. IL ILRIPPLE Inductor Current (IL) ILOAD LOAD L IL (peak) RS IL (bottom) t -INC VREF +INC 12 11 Current Sence LSAT Comp. LSAT to Drive Logic 9 9:1 S Q 10 A R DS04-27269-1E 21 MB39A130A (10) Over-voltage Protection Circuit Block (OVP Comp.) The circuit protects an output connecting device when the output voltage (VO) rises. This function is that 1.15 times (Typ) of the internal reference voltage (INTREF) that is set by the output voltage setting block (VO REFIN Control) is compared with the voltage that is inverting-input into Error Comp. If the thing that the inverting-input-voltage into Error Comp. has gone up is detected, an SR latch is set, each pin's logic is fixed as described in "Function table when the over-voltage protection circuit block is in operation", and the voltage output is stopped. * Function table when the over-voltage protection circuit block is in operation OUT1 OUT2 CS L (High-side FET:OFF) H (Low-side FET: ON) L PGOOD L * Timing chart example for over-voltage protection operation (PGOOD pulled up to VB) INTREF x 1.15 FB OUT1 OUT2 PGOOD SR latch Detection time 200[ns] (reference value) The over-voltage protection state can be cancelled by setting the IC to standby state first and then resetting the latch using the UVLO signal. Also, the over-voltage protection function can be disabled by causing a short between the COVP pin (Pin 5) and the GND pin (Pin 1). 22 DS04-27269-1E MB39A130A (11) Under-voltage Protection Circuit Block (UVP Comp.) It protects an output connecting device by stopping the output when the output voltage (VO) drops. This function is that 0.7 times (Typ) of the internal reference voltage (INTREF) that is set by the output voltage setting block (VO REFIN Control) is compared with the voltage that is inverting-input into Error Comp. If the thing that the inverting input-voltage into Error Comp. has dropped is detected, the capacitor connected to the CUVP pin (Pin 6) starts charging. When the voltage at the CUVP pin rises and an SR latch is set in UVP Comp., the PGOOD pin (Pin 7) is set to the "L" level and discharge operation is performed to stop the voltage output. * Function table when the under-voltage protection circuit block is in operation OUT1 OUT2 CS L (High-side FET : OFF) L (Low-side FET : OFF) L PGOOD L * Timing chart example for under-voltage protection operation (PGOOD pulled up to VB) FB INTREF x 0.7 OUT1 OUT2 PGOOD VB x 0.5 CUVP SR latch Detection time The under-voltage protection state can be cancelled by setting the IC to standby state first and then resetting the latch using the UVLO signal. Also, the under-voltage protection function can be disabled by causing a short between the CUVP pin and the GND pin (Pin 1). (12) Power-Good Detection Circuit Block (PGOOD Comp.) This function is that 0.9 times (Typ) of the internal reference voltage (INTREF) that is set by the output voltage setting block (VO REFIN Control) is compared with the voltage that is inverting-input into Error Comp. If the thing that the inverting-input voltage into Error Comp. has raised is detected, it determines that the output voltage of the DC/DC converter has reached the setting voltage and turns off N-ch MOS which are built into the PGOOD pin (Pin 7). Timing Chart Example (PGOOD Pulled Up to VB) CTL VB INTREFx0.92 INTREFx0.90 FB PGOOD DS04-27269-1E 23 MB39A130A (13) Output Block (Drv-1, Drv-2) This circuit drives the external N-ch MOS FET. The output circuit is configured in CMOS type for both the highside and the low-side. (14) Control Block (CTL) The block changes to standby state, when the CTL pin (Pin 8) is set to the "L" level. (The maximum power-supply current at standby is 10 A.) Setting the CTL pin to the "H" level can send the DC/DC converter block into operating state. Control Function Table CTL DC/DC converter L OFF H ON (15) Bias Voltage Block (VB Reg.) It outputs 5 V as the power supply to the internal control circuit and for setting the bootstrap voltage. Moreover, it can switch the 5 V power supply to external (VBIN) from internal (VB Reg.). By inputting the voltage of 4.5 V (Typ) or more to the VBIN pin (Pin 18) from outside. (16) Over temperature Protection Circuit Block (OTP) The circuit protects an IC from heat-destruction. If the junction temperature reaches + 150C, the over temperature protection circuit sets the CS pin (Pin 4) to the "L" level, the OUT-1 pin (Pin 20) and the OUT-2 pin (Pin 15) to the "L" level, and turns on the discharge FET (RON 16 ) which is connected between the VO pin (Pin 23) and GND. In addition, if the junction temperature drops to + 125C, the normal operation restarts. The condition for the over temperature protection function to operate is that the maximum rating of this IC is exceeded. Therefore, make sure to design the DC/DC power supply system so that the over temperature protection does not start frequently. 24 DS04-27269-1E MB39A130A PROTECTION FUNCTION TABLE Control/ protection function Output of each pin after detection Detection condition VREF VB DC/DC output dropping operation, etc. OUT-1 OUT-2 L L Self-discharge by load Under Voltage Lock Out (UVLO) VB < 3.3 V VREF < 1.8 V Under Voltage Protection (UVP) FB < INTREF x 0.7 Equivalent to less than VO x 0.7 2.5 V 5V L L Discharge by IC discharge function Discharge stopped at VO 0.3 V Over Voltage Protection (OVP) FB > INTREF x 1.15 Equivalent to VO x 1.15 or more 2.5 V 5V L H VO = 0 V clamping Over Current Protection (ILIM) +INC to -INC > ILIM Equivalent to over current detection value 2.5 V 5V Over Temperature Protection Tj > + 150C (OTP) CONTROL (CTL) DS04-27269-1E CTL: H L (VO > 0.3 V) < 1.8 V < 3.3 V 2.5 V 2.5 V 5V 5V Dropping by constant current switching switching (Output drops but does not stop) L L L Discharge by IC discharge function Discharge stopped at VO 0.3 V L Discharge by IC discharge function VREF = 0 V, VB = 0 V, and discharge stopped at VO 0.3 V 25 MB39A130A I/O PIN EQUIVALENT CIRCUIT DIAGRAM <<Reference voltage block>> <<ON/OFF time generator block>> VB VB ESD protection element 3 VREF ESD protection element GND RT 22 GND <<Over voltage protection block>> <<Under voltage protection block>> <<ON/OFF time generator block>> VB VB FSW 13 COVP CUVP 3 5, 6 GND GND <<Bias voltage block>> VCC 16 VB 18 VBIN 4.5V GND (Continued) 26 DS04-27269-1E MB39A130A <<Power-Good detection block>> 7 PGOOD GND <<Control block>> <<Soft-start block>> VCC VB VB 0.1 V CTL 8 4 CS GND GND <<Output voltage setting block (FB)>> <<Output voltage setting block (VO)>> VB VO 23 2.5 V FB 24 GND GND (Continued) DS04-27269-1E 27 MB39A130A (Continued) <<Current detection block>> <<Over current detection block>> VB VB ILIM 10 +INC -INC 11 12 GND GND <<Output voltage setting block (REFIN)>> <<Oversaturation detection block>> VB VB 2.5 V LSAT REFIN 9 2 0.3 V GND GND <<Output block (OUT-1)>> <<Output block (OUT-2)>> 21 CB 16 20 OUT-1 19 LX GND 28 VB 15 OUT-2 GND 14 PGND DS04-27269-1E MB39A130A EXAMPLE APPLICATION CIRCUIT VB 16 VB VO D2 23 VB VBIN C4 18 VB 12 CB FB 21 C7 24 -INC VCC 15 V 17 C1-1 VIN C2-1 8 CTL VCC +INC C16 11 PGND CTL Q1 VB OUT-1 9 20 LSAT MB39A130A 10 ILIM R16 R15 LX 1.2 V, 3 A L1 VREF C9 3 19 OUT-2 C11 R5 C12 4 VB 5 COVP 13 FSW 22 RT 6 CUVP 1 DS04-27269-1E Q1 CS GND PGND1 R13 C10 15 C5-2 REFIN D1 2 C5-1 VO PGOOD PGND 7 PGOOD 14 29 MB39A130A PARTS LIST Component Item Specification Vendor Package Part number Remarks Q1 N-ch FE VDS = 30 V, ID = 8 A, Ron = 21 m NEC SO-8 uPA2755 Dual type (2 elements) D1 Diode Io = 1A, VRRM = 40 V, VF = 0.55 V at IF = 1A D2 Diode L1 Onsemi SOD-123FL MBR140SFT1 VF = 0.4 V (Max) at IF = 0.2 A Onsemi SOD-523 BAT54XV2T1G Inductor 2.2 uH (10 m, 6.1 A) TDK RLF7030T-2R2M5R4 C1-1 Ceramic capacitor 22 u (25 V) TDK 3225 C3225JC1E226M C1-2 Ceramic capacitor 22 u (25 V) TDK 3225 C3225JC1E226M C4 Ceramic capacitor 4.7 u (6.3 V) TDK 1608 C1608JB0J475M C5-1 POSCAP 220 u (4 V, 40 m) SANYO D 4TPC220M C5-2 Ceramic capacitor 1000 p (50 V) TDK 1608 C1608CH1H102J C7 Ceramic capacitor 0.1 u (50 V) TDK 1608 C1608JB1H104K C9 Ceramic capacitor 0.1 u (50 V) TDK 1608 C1608JB1H104K C10 Ceramic capacitor 0.022 u (25 V) TDK 1608 C1608JB1H223K C11 Ceramic capacitor 470 p (50 V) TDK 1608 C1608CH1H471J C12 Ceramic capacitor 470 p (50 V) TDK 1608 C1608CH1H471J C13 Ceramic capacitor 470 p (50 V) TDK 1608 C1608CH1H471J C16 Ceramic capacitor 0.1 u (50 V) TDK 1608 C1608JB1H104K R5 Resistor 43 k SSM 1608 RR0816P433D R13 Resistor 100 k SSM 1608 RR0816P104D R14 Resistor 56 k SSM 1608 RR0816P563D R15 Resistor 43 k SSM 1608 RR0816P433D R16 Resistor 22 k SSM 1608 RR0816P223D NEC Onsemi SANYO TDK SSM 30 : NEC Electronics Corporation : ON Semiconductor Corporation : SANYO Electric Co., Ltd. : TDK Corporation : SUSUMU CO., LTD. DS04-27269-1E MB39A130A APPLICATION NOTE [1] Setting Operating Conditions Setting output voltages 1. When the output setting voltages (VO) are 1.2 V and 2.5 V: They can be set by the internal preset function. In this case, the smallest number of parts is required for the setting, as it is not necessary to apply a reference voltage externally or use a resistor to set the output voltage. REFIN pin FB pin Output voltage setting value (VO) GND VB VO = 1.2 V VB VB VO = 2.5 V VB: Power supply voltage of control system (VB voltage) 2. When the output setting voltages (VO) are other than 1.2 V and 2.5 V: They can be set by fixing the reference voltage of Error Comp. to 0.7 V and adjusting the output voltage setting resistor value ratio. For setting VO 1.5 V, use it with REFIN = VB. REFIN pin FB pin Output voltage setting value (VO) GND Output setting voltage setting resistor connected VO = R1 + R2 VO x 0.7 + R2 2 VB Output setting voltage setting resistor connected VO = R1 + R2 VO x 1.457 + R2 2 The output ripple voltage value is calculated by the following formula. VO = ESR x VO L VIN VO fOSC VIN - VO L x VO VIN x fOSC VO : Output ripple voltage [V] : Coil inductor value [H] : Power supply voltage [V] : Output setting voltage [V] : Oscillation frequency [Hz] VO R1 FB R2 3. When setting / changing the output setting voltage dynamically: The output voltage can be set / changed dynamically by changing the REFIN voltage (VREFIN) under the following condition. The output voltage setting value can be set within the range from 0.855 V to 3.762 V. VB: Power supply voltage of control system (VB voltage) REFIN pin FB pin Following voltage applied externally (0.5 to 2.2 V) VB Output voltage setting value (VO) VO = 1.71 x VREFIN Note: When the output voltage set as mentioned above the method 2 or 3, select a resistor value that achieves R1//R2 50 [k] as a target. DS04-27269-1E 31 MB39A130A In output voltage setting method 2 or 3, the oscillation frequency may become unstable, if the output voltage setting resistor value ratio (R1/R2) is high. This occurs because the value of the ripple voltage applied to the FB pin is reduced by the R1/R2 ratio. In this case, a stable oscillation frequency can be achieved by increasing the output ripple voltage or adding a capacitor in parallel to R1. Select an additional capacitor using the following formula as a guide. CFB 10 x (R1 + R2) 2 x fOSC x R1 x R2 CFB R1,R2 fOSC : Feedback capacitor [F] : Output voltage setting resistor value [] : Oscillation frequency [Hz] VO Vo R1 R2 CFB FB Moreover, the output voltage increases because the output ripple voltage increases by adding a capacitor. The following formula is used to calculate the output voltage increase. If it is required to adjust the output voltage, change the output voltage setting resistor value. VO_OFFSET = (VO - INTREF) x VO 2 x INTREF VO_OFFSET VO VO INTREF : Output setting voltage offset value [V] : Output setting voltage [V] : Output ripple voltage [V] : Error Comp. reference voltage [V] (For details, see "Output Voltage Setting Table" in " FUNCTION"). V VO VO VO_OFFSET t 32 DS04-27269-1E MB39A130A Consideration of output ripple voltage This device requires an output ripple voltage as an operating principle. It must secure about 20 mV at the FB pin voltage. Calculate the output ripple voltage required for the output of the DC/DC converter by the following formula. VO K x 20 mV VO : Output ripple voltage [V] K : Coefficient: When CFB is used: K = 1; When CFB is not used : K = VO INTREF : Output setting voltage [V] VO INTREF : Error Comp. reference voltage [V] (For details, see "Output Voltage Setting Table" in " FUNCTION"). A stable oscillation frequency can be achieved by increasing the output ripple voltage. The output ripple voltage can be increased by selecting a larger output capacitor ESR or a smaller inductor value. However, if the output ripple voltage is increased excessively, the slope of the output ripple voltage during the off-period becomes steeper, which affects the bottom detection voltage more. As a result, it affects the output voltage. This become prominent, if it increase on-duty or oscillation frequency. Ensure that the ripple voltage at the FB pin is not excessively large. Setting oscillation frequency The operating frequency can be set as shown in the following table, according to the state of the RT and FSW pins. RT FSW Operating frequency Connect resistor (RRT) between RT and GND GND Frequency set by the following RRT formula* GND VREF ( 300 kHz) GND VB ( 550 kHz) *: ( RRT = 109 fOSC VCC x 30 ) VO , 20 x 10 3 RRT 160 x 103 0.059 RRT VCC VO fOSC - : Timing resistor value [] : Power supply voltage (VIN) [V] : Output setting voltage [V] : Oscillation frequency [Hz] Note: Set the oscillation frequency so that the on-time (tON) is more than 100 ns and the off-time (tOFF) is more than the minimum off-time. (For how to calculate the on-time and the off-time, see "(5) ON/OFF Time Generator Block" in " FUNCTION". For the minimum off-time, see "ON/OFF Time Generator Block [tON Generator]" in "ELECTORICAL CHARACTERISTICS".) DS04-27269-1E 33 MB39A130A Setting over voltage protection function/under voltage protection function For each function, the timer can be set for the time until it stops. Calculate each setting capacitor value by the following formula. COVP = 11 x tOVP VB COVP : OVP pin capacitor value [pF] tOVP : Over voltage detection time [s] VB : VB power supply voltage [V] CUVP = 11 x tUVP VB CUVP : UVP pin capacitor value [pF] tUVP : Under voltage detection time [s] VB : VB power supply voltage [V] Connect the COVP pin to GND when not using the over-voltage protection function. Connect the CUVP pin to GND when not using the under-voltage protection function. Setting over current protection function / oversaturation protection function Used to limit load current. Output voltage drops to limit the over-current flowing. When the over-current status is Over current finished, the output voltage gets back to the normal setting value. protection function (If the latch function is required to stop the output, it is realized to be used together with the under voltage protection function.) Use this function if there is a concern about saturation of the inductor (a decrease in inductance) due to inductor current that flows when the above over current is detected. This function is not required when a inductor with a sufficient amount of current is used. Oversaturation Output voltage drops to limit the over-current flowing. When the over-current status is protection function finished, the output voltage gets back to the normal setting value. (If the latch function is required to stop the output, it is realized to be used together with the under voltage protection function.) A current sense resistor is connected between the inductor and output, when using the over current protection/ oversaturation protection function. Since the input limit of +INC is 2.9 V, the following conditions must be met. 2.9 ( ILIM + IL VO ILIM RS IL = ) x RS + VO : Ripple current peak-to-peak value of inductor [A] : Output setting voltage [V] : Over current detection value [A] : Current sense resistor value [] VO VIN - VO x L VIN x fOSC L VIN VO fOSC 34 IL 2 : Inductor value [H] : Power supply voltage of switching system [V] : Output setting voltage [V] : Oscillation frequency [Hz] DS04-27269-1E MB39A130A VB OUT-1 Vo LX LSAT OUT-2 PGND VIN +INC -INC If the voltage at the +INC pin exceeds 2.9 V due to the output voltage setting value, connect a current sense resistor between GND and the source of the low-side FET. VB OUT-1 Vo LX LSAT OUT-2 -INC VIN +INC PGND DS04-27269-1E 35 MB39A130A The oversaturation protection function cannot be used in this connecting arrangement. Connect the LSAT pin to the VB pin. Also, it is necessary to confirm that the voltage between LX and GND when the low-side FET is turned on is smaller than the forward voltage of the fly-back diode. Calculate the voltage between LX and GND by the following formula. VLX = ( ILIM + VLX IL ILIM RS RON IL 2 ) x ( RS + RON ) : Voltage between LX and GND : Ripple current peak-to-peak value of inductor [A] : Over current detection value [A] : Current sense resistor value [] : Low-side FET on-resistance [] It is also necessary to confirm that the minimum voltage at the -INC pin is -0.3[V] or more. Calculate the -INC pin voltage by the following formula. V-INC_MIN = - ( ILIM + V-INC_MIN IL ILIM RS IL 2 ) x RS : -INC minimum voltage : Ripple current peak-to-peak value of inductor [A] : Over current detection value [A] : Current sense resistor value [] The on-resistance of the low-side FET can be used to detect over-current conditions by connecting the +INC pin and the -INC pin to the low-side FET drain and source. VB OUT-1 Vo LX LSAT -INC OUT-2 VIN +INC PGND 36 DS04-27269-1E MB39A130A Since this connection arrangement does not require a current sense resistor, it is cost-effective. It is also advantageous in conversion efficiency, as there is no loss related to a current sense resistor. However, as the over current detection value (ILIM) is affected by fluctuation / variation in the on-resistance of the low-side FET, enough margin must be secured for the maximum load current (IOMAX). When calculating the over current detection value, replace the current sense resistor value (RS) with the on-resistance of the low-side FET (RON). In addition, the oversaturation protection function cannot be used. Connect the LSAT pin to the VB pin. (1) When using oversaturation protection function and over current protection function Calculate each setting resistor value of the over-current detection value (ILIM) and the oversaturation detection current value (ILSAT) by the following formula. KLIM = 4 x RS x ( ILIM - IL IL IL ), KLIM' = 4 x RS x ( ILIM' - ), KLSAT = 4 x RS x ( ILSAT - ) 2 2 2 R3 R2 + R3 R1 + R2 + R3 R1 x 10-5 x KLIM' = KLIM, = KLIM' = KLSAT, + R1 + R2 + R3 R1 + R2 + R3 R3 2.5 100 x 103 R1 + R2 + R3 30 x 103 CLSAT 5 fOSC x R1//(R2+R3) ILIM ILIM' ILSAT IL RS IOMAX CLSAT fosc : Over current detection value [A] ( 2 x IOMAX ILIM 1.5 x IOMAX as target) : Current detection value after oversaturation detection [A] (ILIM' 1.2 x IOTYP as target) : Oversaturation detection current value [A] 2.5 x IL (ILSAT 1.5 x ILIM - as target) 2 : Ripple current peak-to-peak value of inductor [A] : Current sense resistor value [] : Maximum load current [A] : LSAT pin connection capacitor value [F] : Oscillation frequency [Hz] VREF R1 CLSAT LSAT R2 ILIM R3 DS04-27269-1E 37 MB39A130A (2) When only using over current protection function Connect the LSAT pin to the VB pin to disable the oversaturation protection function. The over current detection value is set using the resistor value connected to the ILIM pin. Calculate each resistor value by the following formula. R1 = ( IL 1 ) - 1) x R2, KLIM = 4 x RS x ( ILIM - KLIM 2 100 x 103 R1 + R2 30 x 103 ILIM IL RS : Over current detection value [A] : Ripple current peak-to-peak value of inductor [A] : Current sense resistor value [] VB VREF LSAT R1 ILIM R2 When setting the over current detection value internally, connect the ILIM pin to the VB pin. This setting does not require the resistor to set the over current detection value (ILIM). Calculate the internally set over current detection value (ILIM) by the following formula. ILIM = 0.05 IL + 2 RS ILIM IL RS 38 : Over current detection value [A] : Ripple current peak-to-peak value of inductor [A] : Current sense resistor value [] DS04-27269-1E MB39A130A Power dissipation and the thermal design As for this IC, considerations of the power dissipation and thermal design are not necessary in most cases because of its high efficiency. However, such considerations are necessary for the use at the conditions of a high power supply voltage, a high oscillation frequency, high load, and the high temperature. Calculate IC internal loss (PIC) by the following formula. PIC = VCC x (ICC + Qg x fOSC) PIC VCC ICC Qg fOSC : IC internal loss [W] : Power supply voltage [V] (VIN) : Power supply current [A] (2.2 mA Max) : Total quantity of charge for all switching FET [C] (Total at Vgs = 5 V) : Oscillation frequency [Hz] Calculate junction temperature (Tj) by the following formula. Tj = Ta + ja x PIC Tj Ta ja PIC : Junction temperature [C] ( + 125C Max) : Operation ambient temperature [C] : TSSOP-24 Package thermal resistance ( + 76C/ W) : IC internal loss [W] VB Regulator In the condition for which the potential difference between VCC and VB is insufficient, the decrease in the voltage of VB happens because of power output on-resistance and load current (mean current of all external FET gate driving current and load current of internal IC) of the VB regulator. Stop the switching operation when the voltage of VB decreases and it reaches threshold voltage (VTHL) of the under voltage lockout protection circuit. Therefore, set oscillation frequency or external FET or I/O potential difference of the VB regulator using the following formula as a target when you use this IC. When using it in the condition for which the I/O potential difference is insufficient, check the operation on an actual device carefully during normal operation, startup and shutdown. VIN VB(VTHL) + (Qg x fOSC + ICC) x RVB VIN VB(VTHL) Qg fOSC ICC RVB DS04-27269-1E : Power supply voltage [V] : Threshold voltage of under-voltage lockout protection circuit = 3.5 [V] Max : Total amount of gate charge of external FET [C] : Oscillation frequency [Hz] : Power supply current = 3 x 10- [A] ( Load current of VB (LDO)) : Output on-resistance = 100 [] (The reference value at VIN = 4.5 V) 39 MB39A130A [2] Selection of Parts Selection of smoothing inductor As an approximate guide, the inductor value to be selected should be a value which allows the ripple current peak-to-peak value of the inductor to be 50 [%] or less of the maximum load current. Calculate the inductor value in this case by the following formula. L VIN - VO VO x LOR x IOMAX VIN x fOSC L IOMAX LOR VIN VO fOSC : inductor value [H] : Maximum load current [A] : Ratio of inductor ripple current peak-to-peak value and Maximum load current (0.5) : Power supply voltage of switching system [V] : Output setting voltage [V] : Oscillation frequency [Hz] It is necessary to calculate the maximum current value that flows to the inductor to judge whether the electric current that flows to the inductor is a rated value or less. Calculate the maximum current value of the inductor by the following formula. IL 2 ILMAX IOMAX + IL = VIN - VO L ILMAX IOMAX IL L VIN Vo fOSC x VO VIN x fOSC : Maximum current value of inductor [A] : Maximum load current [A] : Ripple current peak-to-peak value of inductor [A] : Inductor value [H] : Power supply voltage of switching system [V] : Output setting voltage [V] : Oscillation frequency [Hz] Inductor current IL MAX I OMAX 0 40 IL Time DS04-27269-1E MB39A130A Selection of Switching FET The maximum value of the current that flows to the switching FET must be calculated in order to determine whether the current flowing to the switching FET is within the rated value. Calculate the maximum value of the current that flows to the switching FET by the following formula. ID = IoMAX + ID IOMAX IL IL 2 : Drain current [A] : Maximum load current [A] : Ripple current peak-to-peak value of inductor [A] Moreover, it is necessary to calculate the loss of switching FET to judge whether a power dissipation of switching FET is a rated value or less. Calculate the conduction loss on the switching FET by the following formula. High-side FET conduction loss PRON = IoMAX2 x RON x PRON IOMAX VIN VO RON VO VIN : High-side FET conduction loss [W] : Maximum load current [A] : Power supply voltage of switching system [V] : Output setting voltage [V] : High-side FET ON resistance [] Low-side FET conduction loss PRON = IoMAX2 x RON x (1 - PRON IOMAX VIN VO RON VO ) VIN : Low-side FET conduction loss [W] : Maximum load current [A] : Power supply voltage of switching system [V] : Output setting voltage [V] : Low-side FET on-resistance [] The gate drive power of switching FET is supplied by LDO in IC, therefore all of the allowable maximum total gate charge (QgTotalMax) of all switching FET is calculated by the following formula. QgTotalMax 30000 fOSC QgTotalMax : Allowable maximum total gate charge of all switching FET [nC] : Oscillation frequency [kHz] fOSC DS04-27269-1E 41 MB39A130A Selection of fly-back diode Select schottky barrier diode (SBD) with the smallest possible forward voltage (Vf). In this DC/DC control IC, the period where electric current flows to fly-back diode is limited to synchronous rectification period (50 ns x 2) as the synchronous rectification method is used. For example, when the oscillation frequency is 600 kHz, the current flow time rate is 6%. Therefore, select a fly-back diode current that does not exceed the forward current surge peak ratings of fly-back diode (IFSM). Calculate the forward current surge peak ratings of fly-back diode by the following formula. IFSM IoMAX + IFSM IOMAX IL IL 2 : Forward current surge peak ratings of SBD [A] : Maximum load current [A] : Ripple current peak-to-peak value of inductor [A] Note: When the forward voltage (Vf) of schottky barrier diode (SBD) is high and the load current of DC/DC output is large, the output may be stopped due to false detection by the protection function. This problem can be solved by changing to schottky barrier diode (SBD) of a smaller forward voltage. 42 DS04-27269-1E MB39A130A Selection of output capacitor A certain level of ESR is required for stable operation of this IC. Use a tantalum capacitor or polymer capacitor as the output capacitor. A ceramic capacitor with low ESR can also be used if a resistor is connected in series with it to increase ESR equivalently. Calculate the necessary ESR value for the output capacitor by the following formula. ESR VO IL ESR VO IL : Series resistance component of output capacitor [] : Output ripple voltage [V] : Ripple current peak-to-peak value of inductor [A] Select the output capacitor value using the following condition as a guide. CO 1 4 x fOSC x ESR CO fOSC ESR : Output capacitor value [F] : Oscillation frequency [Hz] : Series resistance component of output capacitor [] Moreover, derive the output capacitor value from the allowable overshoot and the amount of overshoot. The following formula applies when the current through rate for a sudden load change is , which is the worst condition. For a lower through rate, the output capacitor value to be used can be smaller than the value calculated by the following formula. CO CO IO2 x L 2 x VO x VO_OVER *** Overshoot condition IO2 x L x (VO + VIN x fOSC x 480 x 10-9) 2 x VO x VO_UNDER x (VIN - VO - VIN x fOSC x 480 x 10-9) CO VO_OVER VO_UNDER IO L VIN VO fOSC *** Undershoot condition : Output capacitor value [F] : Allowable amount of output voltage overshoot [V] : Allowable amount of output voltage undershoot [V] : Electric current difference in sudden load change [A] : Inductor value [H] : Power supply voltage [V] : Output setting voltage [V] : Oscillation frequency [Hz] Note: The capacitor has frequency, operating temperature, bias voltage and other characteristics. Therefore, it must be noted that its effective capacitance may be significantly smaller, depending on the use conditions. Calculate the allowable ripple current of the output capacitor by the following formula. DS04-27269-1E 43 MB39A130A Irms IL 2 3 Irms IL : Allowable ripple current (effective value) [A] : Ripple current peak-to-peak value of inductor [A] Selection of input smoothing capacitor Select the input capacitor with the smallest possible ESR. A ceramic capacitor will be ideal. Use a polymer capacitor or tantalum capacitor with low ESR, if a ceramic capacitor is not enough and a mass capacitor is required. Calculate the required capacitor value of the input capacitor using the following formula as a guide. CIN VO x CO VIN CIN CO VO VIN : Input capacitor value [F] : Output capacitor value [F] : Output voltage [V] : Power supply voltage of switching system [V] A ripple voltage occurs due to the switching operation of DC/DC, if a inductor is connected as a noise filter between the power supply of the switching system and the input capacitor and the cut-off frequency for this inductor and input capacitor is set to a value lower than the oscillation frequency. In this case, consider the lower limit of the input capacitor also in relation to the allowable ripple voltage. Calculate the ripple voltage of the power supply of the switching system by the following formula. VIN = IOMAX VO x VIN x fOSC CIN VIN IOMAX CIN VIN VO fOSC ESR IL + ESR x (IOMAX + IL ) 2 : Switching system power supply ripple voltage peak-to-peak value [V] : Maximum load current value [A] : Input capacitor value [F] : Power supply voltage of switching system [V] : Output setting voltage [V] : Oscillation frequency [Hz] : Series resistance component of input capacitor [] : Ripple current peak-to-peak value of inductor [A] Note: The capacitor has frequency, temperature, bias voltage and other characteristics. Therefore, it must be noted that its effective value may be significantly smaller, depending on the use conditions. 44 DS04-27269-1E MB39A130A The ripple current must be considered when using a capacitor that has a rated value for its allowable ripple current. Calculate the ripple current by the following formula. VO x (VIN - VO) Irms IOMAX x Irms IOMAX VIN VO VIN : Allowable ripple current (effective value) [A] : Maximum load current value [A] : Power supply voltage of switching system [V] : Output setting voltage [V] Current sense resistor Select a ripple voltage (VRs) of about 100 mV as a target for the inductor current and the current sense resistor. Calculate the resistor value by the following formula. VRs RS ILIM - Rs VRs ILIM IL IL 2 : Current sense resistor value [] (or low-side FET on-resistance (RON)) : Ripple voltage of current sense resistor [V] (about 100 mV is recommended as a target) : Current limit value [A] : Ripple current peak-to-peak value of inductor [A] Select the power dissipation of the current sense resistor so that it does not exceed the allowable dissipation amount. Power dissipation of current sense resistor = RS x IOMAX2 x (1 - VO/VIN) [W] RS IOMAX VIN VO DS04-27269-1E : Current sense resistor value [] (or low-side FET on-resistance (RON)) : Maximum load current value [A] : Power supply voltage of switching system [V] : Output setting voltage [V] 45 MB39A130A Boot strap diode Select Schottky barrier diode (SBD) with the smallest possible forward current. The electric current that drives the gate of high-side FET flows to boot strap diode. Calculate the mean current by the following formula. Select it so as not to exceed the electric current ratings. ID QG x fOSC ID QG fOSC : Forward current [A] : Total quantity of charge of gate on high-side FET [C] : Oscillation frequency [Hz] Boot strap capacitor To drive the gate of high-side FET, the bootstrap capacitor must have enough stored charge. Therefore, a minimum value as a target is assumed the capacitor value which can store electric charge 10 times that of the Qg on high-side FET. And select the boot strap capacitor. CBOOT 0.002 x Qg CBOOT Qg : Bootstrap capacitor value [F] : Amount of gate charge on high-side FET [nC] VB pin capacitor 2.2 F is assumed to be a standard, and when Qg of Switching FET used is large, it is necessary to adjust it. To drive the gate of high-side FET, the bootstrap capacitor must have enough stored charge. Therefore, a minimum value as a target is assumed the capacitance which can store electric charge 100 times that of the Qg on Switching FET. And select it. Moreover, capacitor change may cause an overshoot when CTL was turned on. Although the overshoot does not affect DC/DC operation, it must be made sure that the VB pin does not exceed its rating before its application. CVB 0.02 x Qg CVB Qg 46 : VB pin capacitor value [F] : Total amount of gate charge on Switching FET [nC] DS04-27269-1E MB39A130A Setting method of soft-start time To prevent a rush current to IC starting, soft-start time can be set by connecting a soft-start capacitor (CS) to the CS pin. When the IC starts with the CTL pin set to the "H" level, the bias voltage output capacitor (CVB) which is externally connected to the VB pin starts charging. When the threshold voltage VB UVLO_VB is reached, the reference voltage output capacitor (CREF) which is externally connected to the VREF pin starts charging. When the threshold voltage VREF UVLO_VREF is reached, the soft-start capacitor (CS) which is externally connected to the CS pin starts charging at 5 A. The lower one of the electric potentials of the two non inverting input pins (INTREF, CS pin voltage) is compared with the voltage at the inverting input pin (INTFB) and Error Comp. output is decided. Consequently, the output of Error Comp. during the soft-start period (CS pin voltage < INTREF) is determined by comparing the INTFB voltage with the voltage at the CS pin, and the output voltage of the DC/DC converter increases in proportion to the voltage at the CS pin due to the charging to the soft-start capacitor that is externally connected to the CS pin. Calculate the soft-start time by the following formula. ts 0.22 x INTREF x CS x 106 ts INTREF CS : Soft-start time [S] (time until output reaches 100%) : Error Comp. reference voltage [V] : CS pin capacitor value [F] Note: If the CTL pin is changed from "H" to "L", IC's internal SW (RON 16 ) which is connected to the VO pin is turned on to discharge output. When the output voltage falls below 0.3 V, the IC shuts down. Calculate the soft-start starting time by the following formula. 3 tds (80 + 4.50 x 104 x CVB 5 ) x (9.40 x 10-5 x VCC4 - 6.36 x 10-3 x VCC3 + 1.57 x 10-1 x VCC2 - 1.66 x VCC + 7.30) + 15.0 tds VCC CVB DS04-27269-1E : Soft-start starting time [ns] (time until soft-start operation starts) : Power supply voltage [V] ( = VIN [V]) : VB pin capacitor value [F] 47 MB39A130A 2.5 V Voltage at CS pin = INTREF 0V Error Comp. reference voltage Soft-start time (ts) IC standby Voltage at VO pin 0.3 V VREF pin VB pin H CTL signal L Soft-start starting time (tds) 48 t DS04-27269-1E MB39A130A About the synchronization of multiple units of IC The power ON/OFF sequence must be controlled, if multiple units of MB39A130A are used to supply various power supply voltages to the system. In this case, the connection shown in the following diagram may be adopted to allow simultaneous soft-start/discharge operation of multiple ICs using the same timing during power-up/power-down. It should be noted that as discharge operation is performed by NMOS SW, the decreasing rate of the output after CTL is disconnected varies depending on the setting of each output. <Connection example 1> When aligning soft-start time When aligning the soft-start time, set the reference voltage of Error Comp. of each IC to the same value. For example, short all of the REFIN pins (Pin 2) of ICs to GND. DC/DC 1: Vo = 2.0 V set 4:CS Vo:23 104 k V FB:24 MB39A130 A CTL 8:CTL < DC/DC 1 > 56 k REFIN:2 2.0 V Vo 1.5 V DC/DC 2: Vo = 1.5 V set 4:CS < DC/DC 2 > Vo:23 64 k FB:24 MB39A130A CTL 56 k 8:CTL REFIN:2 t CS <Connection example 2> When aligning soft-start slope When aligning the slope of the output voltage of each IC at soft-start, use the same output voltage setting resistor value ratio for all of the ICs and adjust the output voltages by adjusting the reference voltage of Error Comp. DC/DC 1: Vo = 2.0 V set 4:CS Vo:23 64 k V FB:24 MB39A130A CTL 8:CTL REFIN:2 < DC/DC 1 > 56 k 2.0 V (1.167 V) Vo DC/DC 2: Vo = 1.5 V set 4:CS 1.5 V < DC/DC 2 > Vo:23 64 k FB:24 MB39A130A CTL 56 k 8:CTL REFIN:2 t CS DS04-27269-1E 49 MB39A130A Layout Consider the points listed below and do the layout design. * Provide the ground plane as much as possible on the IC mounted face. Connect bypass capacitor connected with the VCC and VB pins and GND pin of the switching system parts as well as the PGND pin of the IC with switching system GND (PGND). Connect other GND connection pins with control system GND (AGND), and separate each GND, and try not to pass the heavy current path through the control system GND (AGND) as much as possible. In that case, connect control system GND (AGND) and switching system GND (PGND) at a single GND (PGND) point of the IC. * Connect the switching system parts as much as possible on the surface. Avoid the connection through the through-hole as much as possible. * As for GND pins of the switching system parts, provide the through hole at the proximal place, and connect it with GND of internal layer. * Pay the most attention to the loop composed of input capacitor (CIN), switching FET, and fly-back diode (SBD). Consider making the current loop as small as possible. * Place the boot strap capacitor proximal to CB and LX pins of IC as much as possible. * Large electric current flows momentary in the net of OUT-1 and OUT-2 pins connected with the gate of switching FET. Wire the linewidth of about 0.8 mm to be a standard, as short as possible. * By-pass capacitor connected with VREF, VCC, and VB, and the resistor connected with the RT pin should be placed close to the pin as much as possible. Also connect the GND pin of the bypass capacitor with GND of internal layer in the proximal through-hole. * +INC and -INC pins are very sensitive to noise. Therefore, pull them out individually near a pin of the element that plays the current sense role. Then, wire them close to each other through remote sensing (Kelvin connection). Also consider keeping them away from switching system parts as much as possible. * Pull the feedback line to be connected to the VO pin of the IC separately from near the output capacitor pin, whenever possible, in order to feed back it to the IC more accurately. It is the ripple voltage which is generated from ESR of the output capacitor. Consider the net connected with VO and FB pins to keep away from a switching system parts as much as possible because it is sensitive to the noise. Moreover, place the output voltage setting resistor connected with this net close to the IC as much as possible, and try to make the net as short as possible. In addition, for the internal layer right under the mounting part of the output voltage setting resistor, provide the control system GND (AGND) of few ripple and few spike noises, or provide the ground plane of the power supply voltage as much as possible. 50 DS04-27269-1E MB39A130A Switching system parts: Input capacitor (CIN), Switching FET, Fly-back diode (SBD), Inductor (L), Current sensor (Rs), Output capacitor (Co) GND Layout Example Example layout of SW system parts Layout of output voltage setting resistor Switching FET AGND 1pin VIN CIN PGND SBD PGND Co L Rs Vo To +INC and -INC AGND Connect GND and PGND at a single point Surface DS04-27269-1E PGND Through-hole To VO Internal layer 51 MB39A130A REFERENCE DATA Conversion efficiency vs.Load current 100 100 95 95 Conversion efficiency (%) Conversion efficiency (%) Conversion efficiency vs.Load current 90 VO = 1.2 V 85 80 75 70 VCC = 15 V RT = 43 k 65 60 0 1 2 VO = 2.5 V 85 80 75 70 VCC = 15 V RT = 43 k 65 60 3 0 1 2 3 Load current IO (A) Load current IO (A) Oscillation frequency vs.Load current Oscillation frequency vs.Load current 600 Oscillation frequency fosc (kHz) 550 Oscillation frequency fosc (kHz) 90 450 VO = 1.2 V 350 250 VCC = 15 V RT = 43 k 150 0 1 2 Load current IO (A) 3 500 VO = 2.5 V 400 300 VCC = 15 V RT = 43 k 200 0 1 2 3 Load current IO (A) (Continued) 52 DS04-27269-1E MB39A130A Output voltage vs.Load current Output voltage vs.Load current 1.32 2.8 2.7 Output voltage VO (V) Output voltage VO (V) 1.29 1.26 1.23 1.2 1.17 1.14 VCC = 15 V RT = 43 k 1.11 1.08 0 1 2 Load current IO (A) 3 2.6 2.5 2.4 VCC = 15 V RT = 43 k 2.3 2.2 0 1 2 3 Load current IO (A) (Continued) DS04-27269-1E 53 MB39A130A CTL Shutdown Waveform CTL Startup Waveform 200 s/div 1 ms/div CTL : 5 V/div CTL : 5 V/div VO : 1 V/div VO : 1 V/div LX : 10 V/div LX : 10 V/div VIN = 15 V, RT = 43 k, Ta = +25 C, VO = 1.2 V Soft-start setting time = 3.1 ms, IO = 3 A (0.4 ) Output Over Current Waveform(UVP Enabled) VO : 0.5 V/div 100us/div VIN = 15 V, RT = 43 k, Ta = +25 C, VO = 1.2 V, IO = 3 A (0.4 ) Output Over Current Waveform (UVP Disabled) VO : 0.4 V/div IO : 2 A/div IO : 2 A/div 1 ms/div LX : 10 V/div LX : 10 V/div Normal operation Over current protection Under voltage protection VIN = 15 V ,VO = 1.2 V, RT = 43 k, Ta = +25 C Normal operation Over current Normal operation protection VIN = 15 V, RT = 43 k, VO = 1.2 V, CUVP = GND, Ta = +25 C (Continued) 54 DS04-27269-1E MB39A130A (Continued) Dynamic Output Voltage Transition 2.5 V Load Sudden Change Waveform VO : 50 mV/div (1.2 V offset) 1.2 V VO : 0.5 V/div 1.46 V IO : 2 A/div 3A VREFIN : 0.5 V/div 0.7 V 100 s/div 500 s/div VIN = 15 V, IO = 0 A, RT = 43 k, Ta = +25 C DS04-27269-1E 0A VIN = 15 V, VO = 1.2 V 3 A, RT = 43 k, Ta = +25 C IO = 0 55 MB39A130A USAGE PRECAUTION 1. Do not configure the IC over the maximum ratings. If the IC is used over the maximum ratings, the LSI may be permanently damaged. It is preferable for the device to normally operate within the recommended usage conditions. Usage outside of these conditions can have an adverse effect on the reliability of the LSI. 2. Use the device within the recommended operating conditions. The recommended values guarantee the normal LSI operation under the recommended operating conditions. The electrical ratings are guaranteed when the device is used within the recommended operating conditions and under the conditions stated for each item. 3. Printed circuit board ground lines should be set up with consideration for common impedance. 4. Take appropriate measures against static electricity. * * * * Containers for semiconductor materials should have anti-static protection or be made of conductive material. After mounting, printed circuit boards should be stored and shipped in conductive bags or containers. Work platforms, tools, and instruments should be properly grounded. Working personnel should be grounded with resistance of 250 k to 1 M in serial body and ground. 5. Do not apply negative voltages. The use of negative voltages below -0.3 V may make the parasitic transistor activated to the LSI, and can cause malfunctions. ORDERING INFORMATION Part number Package Remarks MB39A130APFT-E1 24-pin plastic TSSOP (FPT-24P-M08) Lead free version EV BOARD ORDERING INFORMATION Part number EV board version No. MB39A130A-EVB-02 MB39A130AEVB-02 Rev3.0 Remarks RoHS COMPLIANCE INFORMATION OF LEAD (Pb) FREE VERSION The LSI products of Fujitsu Microelectronics with "E1" are compliant with RoHS Directive, and has observed the standard of lead, cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE). A product whose part number has trailing characters "E1" is RoHS compliant. 56 DS04-27269-1E MB39A130A MARKING FORMAT (Lead Free version) Lead Free version INDEX DS04-27269-1E 57 MB39A130A LABELING SAMPLE (Lead free version) Lead-free mark JEITA logo JEDEC logo The part number of a lead-free product has the trailing characters "E1". 58 DS04-27269-1E MB39A130A MB39A130APFT- E1 RECOMMENDED CONDITIONS OF MOISTURE SENSITIVITY LEVEL [Fujitsu Microelectronics Recommended Mounting Conditions] Item Condition Mounting Method IR (infrared reflow), Manual soldering (partial heating method) Mounting times 2 times Storage period Before opening Please use it within two years after Manufacture. From opening to the 2nd reflow Less than 8 days When the storage period after opening was exceeded Please process within 8 days after baking (125C, 24h) Storage conditions 5C to 30C, 70%RH or less (the lowest possible humidity) [Mounting Conditions] (1) IR(infrared reflow) 260C 255C Main heating 170 C to 190 C (b) RT (a) "H" level: 260C Max (a)Temperature increase gradient (b)Preliminary heating (c)Temperature increase gradient (d)Peak temperature (d')Main heating (e)Cooling (c) (d) (e) (d') : Average 1C/s to 4C/s : Temperature 170C to 190C, 60 s to 180 s : Average 1C/s to 4C/s : Temperature 260C Max; 255C or more, 10 s or less : Temperature 230C or more, 40 s or less or Temperature 225C or more, 60 s or less or Temperature 220C or more, 80 s or less : Natural cooling or forced cooling Note: Temperature: on the top of the package body (2) Manual soldering(partial heating method) Temperature at the tip of an soldering iron: 400C max Time: Five seconds or below per pin DS04-27269-1E 59 MB39A130A PACKAGE DIMENSIONS 24-pin plastic TSSOP (FPT-24P-M08) 24-pin plastic TSSOP (FPT-24P-M08) Lead pitch 0.50 mm Package width x package length 4.4 x 6.5 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 1.10 mm MAX Weight 0.08 g Code (Reference) P-TSSOP24-4.4x6.5-0.50 Note 1) *1 : These dimensions include resin protrusion. Note 2) *2 : These dimensions do not include resin protrusion. Note 3) Pins width and pins thickness include plating thickness. Note 4) Pins width do not include tie bar cutting remainder. *1 6.500.10(.256.004) 0.170.05 (.007.002) 24 13 *2 4.400.10 6.400.20 (.173.004) (.252.008) INDEX Details of "A" part 1.050.05 (Mounting height) (.041.002) 1 12 0.50(.020) "A" 0.220.05 (.009.002) 0.10(.004) 0~8 M +0.03 0.50(.020) 0.600.15 (.024.006) 0.07 -0.07 +.001 (Stand off) .003 -.003 0.25(.010) 0.08(.003) (c)2002-2008 FUJITSU MICROELECTRONICS LIMITED F24031S-c-1-2 C 2002 FUJITSU LIMITED F24031S-c-1-1 Dimensions in mm (inches). Note: The values in parentheses are reference values. Please confirm the latest Package dimension by following URL. http://edevice.fujitsu.com/package/en-search/ 60 DS04-27269-1E MB39A130A MEMO DS04-27269-1E 61 MB39A130A MEMO 62 DS04-27269-1E MB39A130A MEMO DS04-27269-1E 63 MB39A130A FUJITSU MICROELECTRONICS LIMITED Shinjuku Dai-Ichi Seimei Bldg., 7-1, Nishishinjuku 2-chome, Shinjuku-ku, Tokyo 163-0722, Japan Tel: +81-3-5322-3347 Fax: +81-3-5322-3387 http://jp.fujitsu.com/fml/en/ For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://www.fma.fujitsu.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. 151 Lorong Chuan, #05-08 New Tech Park 556741 Singapore Tel : +65-6281-0770 Fax : +65-6281-0220 http://www.fmal.fujitsu.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm. 3102, Bund Center, No.222 Yan An Road (E), Shanghai 200002, China Tel : +86-21-6146-3688 Fax : +86-21-6335-1605 http://cn.fujitsu.com/fmc/ Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 Kosmo Tower Building, 1002 Daechi-Dong, Gangnam-Gu, Seoul 135-280, Republic of Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://kr.fujitsu.com/fmk/ FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel : +852-2377-0226 Fax : +852-2376-3269 http://cn.fujitsu.com/fmc/en/ Specifications are subject to change without notice. For further information please contact each office. All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited: Sales Promotion Department