AZ AZ762 16 A SPDT MINIATURE POWER RELAY FEATURES * * * * * * * * * * Dielectric strength 5000 Vrms Low cost Epoxy sealed versions available AC and DC coils 16 Amp switching High inrush version available (80 A) Class B (130C) standard Class F (155C) versions available Isolation spacing greater than 10 mm UL, CUR file E44211, VDE 40006031 CONTACTS Arrangement SPDT (1 Form C) SPST (1 Form A, 1 Form B) Ratings Resistive load: Max. switched power: 480 W or 4432 VA Max. switched current: 16 A Max. switched voltage: 150* VDC or 440 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR VDE Material Resistance GENERAL DATA Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 16 A 240 VAC Res. Operate Time (typical) 7 ms at nominal coil voltage Release Time (typical) 3 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20C 500 VDC 50% RH Dropout Greater than 10% of nominal coil voltage (DC) Greater then 15% of nominal coil voltage (AC) Ambient Temperature Operating Storage At nominal coil voltage -40C (-40F) to 100C (212F) -40C (-40F) to 130C (266F) Vibration 0.062" DA at 10-55 Hz Shock 10 g Contact factory for additonal VDE ratings Enclosure P.B.T. polyester [1] Silver cadmium oxide, [2] Silver tin oxide [3] Silver nickel Terminals Tinned copper alloy, P. C. 16 A at 277 VAC resistive, 50k cycles [1] 16 A at 277 VAC resistive, 100k cycles [3] 1 HP at 250 VAC [1] 1 HP at 277 VAC, 40C (1 Form A) [1] 1/2 HP at 125 VAC [1] TV-5 at 125 VAC [1] 16 A at 277 VAC resistive, 75k cycles [2] B300 Pilot Duty [2] R300 Pilot Duty [2] 16 A at 250 VAC resistive [1] and [2] Max. Solder Temp. 270C (518F) Silver cadmium oxide or silver tin oxide or silver nickel. Gold plating available Max. Solder Time 5 seconds < 50 milliohms initially (using 6 V 1 A method) Max. Solvent Temp. 80C (176F) Max. Immersion Time 30 seconds Weight 14 grams COIL Power At Pickup Voltage (typical) 196 mW (DC) 0.43 VA (AC) Max. Continuous Dissipation 1.7 W at 20C (68F) ambient Temperature Rise 26C (47F) at nominal coil voltage NOTES 1. All values at 20C (68F). 2. Relay may pull in with less than "Must Operate" value. Max. Temperature 130C (266F) 3. Specifications subject to change without notice. 9/25/13 AZ AZ762 RELAY ORDERING DATA COIL SPECIFICATIONS - DC COIL Nominal Coil VDC 5 Must Operate VDC 3.5 ORDER NUMBER* Max. Continuous VDC 10.2 Coil Resistance 10% 62 Unsealed Sealed AZ762-1C-5D AZ762-1C-5DE 4.2 12.3 90 AZ762-1C-6D AZ762-1C-6DE 12 8.4 24.7 360 AZ762-1C-12D AZ762-1C-12DE 18 12.6 37.0 810 AZ762-1C-18D AZ762-1C-18DE 24 16.8 49.4 1,440 AZ762-1C-24D AZ762-1C-24DE 48 33.6 98.0 5760 AZ762-1C-48D AZ762-1C-48DE 60 42.0 112.9 7,500 AZ762-1C-60D AZ762-1C-60DE 110 77.0 206.9 25,200 AZ762-1C-110D AZ762-1C-110DE 6 COIL SPECIFICATIONS - AC COIL Nominal Coil VAC 24 115 230 Must Operate VAC 18.0 86.3 172.5 ORDER NUMBER* Max. Continuous VAC 31.2 149.5 299.0 Coil Current (mA) 31.6 6.6 3.2 Coil Resistance 350 10% 8,100 15% 32,500 15% Unsealed Sealed AZ762-1C-24AF AZ762-1C-24AEF AZ762-1C-115AF AZ762-1C-115AEF AZ762-1C-230AF AZ762-1C-230AEF Substitute "1A" or "1B" in place of "1C" for Form A or B respectively. Add suffix "E" to "1A" or "1B" or "1C" for silver tin oxide contacts. Add suffix "B" to "1A" or "1B" or "1C" for silver nickel contacts. Add suffix "A" for gold plated contacts. Add suffix "F" for Class F version (DC coils only). Add suffix "I" at the end of part number for high inrush version 80A (contact form 1AE only, DC coils only, no gold plating). 9/25/13 AZ762 HARDWARE ORDERING DATA DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER Socket ST484-U1 Retainer ST482-3 MECHANICAL DATA .520 Max. [13.2] 1.161 Max. [29.5] PC BOARD LAYOUT VIEWED TOWARDS TERMINALS .197 [5.0] .638 Max. [16.2] .597 [15.16] .197 [5.0] .295 [7.5] .295 [7.5] .161 [4.1] 6X .020 [0.5] .098 [2.5] .098 [2.5] 2X o.024 [o0.6] 2X o.032 [o0.8] 6X o.050 [o1.3] .295 [7.5] 6X .035 [0.9] .197 [5.0] .597 [15.16] .197 [5.0] ST484-U1 .098 [2.5] HARDWARE .500 (12.7) 1.28 (32.5) 1.22 (30.9) WIRING DIAGRAMS VIEWED TOWARDS TERMINALS .414 (10.5) 5 4 * 8* 3 6* .366 (9.3) RETAINING CLIP .295 (7.5) 1 .197 (5.0) .197 (5.0) .590 (15) * Terminals 3 & 6 not used on form A * Terminals 5 & 8 not used on form B .125 DIA (0.5) 2 * 7 .354 (9.0) .177 (4.5) MAX 1.385 [35.19] .895 [22.73] .661 [16.79] .059 DIA (1.5) .118 (3.0) Viewed toward terminals ST482-3 Dimensions in inches with metric equivalents in parentheses. Tolerance: .010" 9/25/13