GENERAL DATA
Life Expectancy Minimum operations
Mechanical 1 x 107
Electrical 1 x 105at 16 A 240 VAC Res.
Operate Time (typical) 7 ms at nominal coil voltage
Release Time (typical) 3 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength 5000 Vrms coil to contact
(at sea level for 1 min.) 1000 Vrms between open contacts
Insulation 1000 megohms min. at 20°C
Resistance 500 VDC 50% RH
Dropout Greater than 10% of nominal coil voltage (DC)
Greater then 15% of nominal coil voltage (AC)
Ambient Temperature At nominal coil voltage
Operating -40°C (-40°F) to 100°C (212°F)
Storage -40°C (-40°F) to 130°C (266°F)
Vibration 0.062" DA at 10–55 Hz
Shock 10 g
Enclosure P.B.T. polyester
Terminals Tinned copper alloy, P.C.
Max. Solder Temp. 270°C (518°F)
Max. Solder Time 5 seconds
Max. Solvent Temp. 80°C (176°F)
Max. Immersion Time 30 seconds
Weight 14 grams
AZ
CONTACTS
Arrangement SPDT (1 Form C)
SPST (1 Form A, 1 Form B)
Ratings Resistive load:
Max. switched power: 480 W or 4432 VA
Max. switched current: 16 A
Max. switched voltage: 150* VDC or 440 VAC
*Note: If switching voltage is greater than 30VDC, special
precautions must be taken. Please contact the factory.
Rated Load
UL, CUR 16 A at 277 VAC resistive, 50k cycles [1]
16 A at 277 VAC resistive, 100k cycles [3]
1 HP at 250 VAC [1]
1 HP at 277 VAC, 40°C (1 Form A) [1]
1/2 HP at 125 VAC [1]
TV-5 at 125 VAC [1]
16 A at 277 VAC resistive, 75k cycles [2]
B300 Pilot Duty [2]
R300 Pilot Duty [2]
VDE 16 A at 250 VAC resistive [1] and [2]
Contact factory for additonal VDE ratings
[1] Silver cadmium oxide, [2] Silver tin oxide
[3] Silver nickel
Material Silver cadmium oxide or silver tin oxide or silver
nickel. Gold plating available
Resistance < 50 milliohms initially (using 6 V 1 A method)
AZ762
16 A SPDT MINIATURE
POWER RELAY
FEATURES
•Dielectric strength 5000 Vrms
•Low cost
•Epoxy sealed versions available
•AC and DC coils
•16 Amp switching
•High inrush version available (80 A)
•Class B (130°C) standard
•Class F (155°C) versions available
•Isolation spacing greater than 10 mm
•UL, CUR file E44211, VDE 40006031
COIL
Power
At Pickup Voltage 196 mW (DC)
(typical) 0.43 VA (AC)
Max. Continuous
Dissipation 1.7 W at 20°C (68°F) ambient
Temperature Rise 26°C (47°F) at nominal coil voltage
Max. Temperature 130°C (266°F)
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
9/25/13
AZ
9/25/13
AZ762
RELAY ORDERING DATA
COIL SPECIFICATIONS - DC COIL ORDER NUMBER*
Nominal Coil Must Operate Max. Continuous Coil Unsealed Sealed
VDC VDC VDC Resistance ±10%
5 3.5 10.2 62 AZ762–1C–5D AZ762–1C–5DE
6 4.2 12.3 90 AZ762–1C–6D AZ762–1C–6DE
12 8.4 24.7 360 AZ762–1C–12D AZ762–1C–12DE
18 12.6 37.0 810 AZ762–1C–18D AZ762–1C–18DE
24 16.8 49.4 1,440 AZ762–1C–24D AZ762–1C–24DE
48 33.6 98.0 5760 AZ762–1C–48D AZ762–1C–48DE
60 42.0 112.9 7,500 AZ762–1C–60D AZ762–1C–60DE
110 77.0 206.9 25,200 AZ762–1C–110D AZ762–1C–110DE
COIL SPECIFICATIONS - AC COIL ORDER NUMBER*
Nominal Coil Must Operate Max. Continuous Coil Current (mA) Coil Resistance Unsealed Sealed
VAC VAC VAC
24 18.0 31.2 31.6 350 ± 10% AZ762–1C–24AF AZ762–1C–24AEF
115 86.3 149.5 6.6 8,100 ± 15% AZ762–1C–115AF AZ762–1C–115AEF
230 172.5 299.0 3.2 32,500 ± 15% AZ762–1C–230AF AZ762–1C–230AEF
Substitute “1A” or “1B” in place of “1C” for Form A or B respectively. Add suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or
“1B” or “1C” for silver nickel contacts. Add suffix “A” for gold plated contacts. Add suffix “F” for Class F version (DC coils only). Add suffix “I” at the end of part
number for high inrush version 80A (contact form 1AE only, DC coils only, no gold plating).
AZ762
9/25/13
[5.0]
.197
[5.0]
.197
VIEWED TOWARDS TERMINALS
PC BOARD LAYOUT
[15.16]
.597
[2.5]
.098
[ø0.8]
2X ø.032
[ø1.3]
[2.5]
.098
.197
[5.0]
.197
[5.0]
[15.16]
[7.5]
[16.2]
.161
6X .035
[4.1]
[0.9]
.638 Max.
[7.5]
6X ø.050
6X .020
[0.5]
.098
[2.5]
.597
.520 Max.
[13.2]
1.161 Max.
[29.5]
.295
.295
[7.5]
2X ø.024
[ø0.6]
.295
WIRING DIAGRAMS
VIEWED TOWARDS TERMINALS
2
1
3
6
4
7
5
8
.500
(12.7)
1.22
(30.9)
1.28
(32.5)
.177
(4.5)
MAX
.354
(9.0)
.366
(9.3)
.125 DIA
(0.5)
.197
(5.0)
.295
(7.5)
.590 (15)
.197
(5.0)
.059 DIA
(1.5)
.118
(3.0)
.414
(10.5)
HARDWARE
RETAINING CLIP
Viewed toward terminals
.661 [16.79]
1.385 [35.19]
.895 [22.73]
**
**
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
MECHANICAL DATA
ST484-U1
ST482-3
* Terminals 3 & 6 not used on form A
* Terminals 5 & 8 not used on form B
HARDWARE ORDERING DATA
DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER
Socket ST484–U1 Retainer ST482–3
