Clock OSC SG7050CAN SG7050CAN 64.000000 MHz TJGA Product name Product Number / Ordering code X1G0044810119xx Please refer to the 8.Packing information about xx (last 2 digits) Output waveform CMOS Pb free / Complies with EU RoHS directive Reference weight Typ. 147 mg 1.Absolute maximum ratings Parameter Symbol Min. Typ. Max. Unit Vcc-GND T_stg Vin -0.3 -40 -0.3 - +4 +125 Vcc+0.3 V C V 2.Specifications(characteristics) Parameter Symbol Min. Typ. Max. Unit f0 Vcc T_use f_tol Icc I_std I_dis SYM VOH VOL L_CMOS VIH VIL 1.71 -40 -50 45 Vcc-0.4 0.8Vcc - 64.000000 - 3.63 +85 50 3 2.7 55 0.4 15 0.2Vcc Rise time tr - - 3.5 ns ST terminal Vcc1.8V10% : 0.2Vcc to 0.8Vcc Level, L_CMOS=15pF Fall time tf - - 3.5 ns Vcc1.8V10% : 0.2Vcc to 0.8Vcc Level, L_CMOS=15pF t_str tDJ tRJ tRMS tp-p - 0 2.4 2.3 20 3 - ms ps ps ps ps tacc - 2.5 - ps tPJ L(f) -3 - 0.17 -88 -117 -142 -153 -157 -158 - 3 - ps dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Maximum supply voltage Storage temperature Input voltage Output frequency Supply voltage Operating temperature Frequency tolerance Current consumption Stand-by current Disable current Symmetry Output voltage Output load condition Input voltage Start-up time Jitter Phase jitter Phase noise Frequency aging f_age 1 Page MHz V C x10-6 mA A mA % Conditions / Remarks Storage as single product ST terminal Conditions / Remarks T_use No load condition Vcc = 3.3V Vcc = 3.3V , ST = GND 50% Vcc Level L_CMOS=<15pF - pF CMOS Load ST terminal -6 x10 t = 0 at 0.9Vcc Deterministic Jitter Vcc=3.3V Random Jitter Vcc=3.3V (RMS of total distribution) Vcc=3.3V Peak to Peak Vcc=3.3V Accumulated Jitter() n=2 to 50000 cycles Off set Frequency: 12kHz to 20MHz, Vcc=3.3V Off set 10Hz Vcc=3.3V Off set 100Hz Vcc=3.3V Off set 1kHz Vcc=3.3V Off set 10kHz Vcc=3.3V Off set 100kHz Vcc=3.3V Off set 1MHz Vcc=3.3V @+25C first year - tr 3.Timing chart tf VCC 80 %VCC 50 %VCC 20 %VCC GND tw t 4.Test circuit swich 1) Waveform observation ST VCC or OE by-pass capacitor supply Test Point OUT GND L_CMOS 2) Current consumption swich VCC A ST or OE by-pass capacitor supply GND OUT Test Point *Current consumption under the disable function should be = GND. 3) Condition (1) Oscilloscope * Band width should be minimum 5 times higher (wider) than measurement frequency. * Probe earth should be placed closely from test point and lead length should be as short as possible * Recommendable to use miniature socket. (Don't use earth lead.) (2) L_CMOS also includes probe capacitance. (3) By-pass capacitor (0.01 F to 0.1 F) is placed closely between VCC and GND. (4) Use the current meter whose internal impedance value is small. (5) Power supply * Start up time (0 %VCC to 90 %VCC) of power source should be more than 150 s. * Impedance of power supply should be as lowest as possible. 2 Page 5.External dimensions (Unit: mm) 6.Footprint(Recommended) (Unit: mm) 7.00.2 #3 1.8 #3 2.0 #4 4.2 C (ex. 0.01 F) C E 25.000 CAN395K #2 #1 Resist 1.30.2 5.00.2 #4 #1 #2 5.08 1.4 1.1 C0.5 5.08 Note. OE pin = "H" or "open" : Specified frequency output. OE pin = "L" : Output is high impedance. ST pin = "H" or "open" : Specified frequency output. ST pin = "L" : Output is high impedanceoscillation stops. 7.Reflow profile Reflow condition (Follow of JEDEC STD-020D.1) Temperature [ C] 300 TP: +260C OVER +255C tp: at least 30 s 250 200 150 TL: +217C Ts max: +200C Ramp-up rate +3 C/s Max. Ramp-down rate -6 C/s Max. tL 60 s to 150 s ( +217 C over ) Ts min: ts +150 C 60 s to 120 s ( +150C to +200C) 100 50 Time: +25 C to Peak 0 60 120 180 240 300 360 420 480 540 600 660 720 Time [ s ] 8.Packing information [ 1 ]Product number last 2 digits code(xx) description The recommended code is "00" X1G0044810119xx Code 01 11 12 Condition Any Q'ty vinyl bag(Tape cut) Any Q'ty / Reel 250pcs / Reel Code 13 00 3 Page Condition 500pcs / Reel 1000pcs / Reel 780 [ 2 ] Taping specification Subject to EIA-481 & IEC-60286 (1) Tape dimensions Material of the Carrier Tape : PS Material of the Top Tape : PET+PE Unit: mm User direction of feed Carrier tape EPSON EPSON Top tape Symbol Value A 1.5 B 4 C 8 D 9.25 (2) Reel dimensions Center material : PS Material of the Reel : PS 4 Page E 16 F 2.3 9.Notice * This material is subject to change without notice. * Any part of this material may not be reproduced or duplicated in any form or any means without the written permission of Seiko Epson. * The information about applied data,circuitry, software, usage, etc. written in this material is intended for reference only. Seiko Epson does not assume any liability for the occurrence of customer damage or infringing on any patent or copyright of a third party. This material does not authorize the licensing for any patent or intellectual copyrights. * When exporting the products or technology described in this material, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. * You are requested not to use the products (and any technical information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that you would not make the products available to any third party who may use the products for such prohibited purposes. * These products are intended for general use in electronic equipment. When using them in specific applications that require extremely high reliability, such as the applications stated below, you must obtain permission from Seiko Epson in advance. / Space equipment (artificial satellites, rockets, etc.) / Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.) / Medical instruments to sustain life / Submarine transmitters / Power stations and related / Fire work equipment and security equipment / Traffic control equipment / And others requiring equivalent reliability. 10.Contact us www5.epsondevice.com/en/contact/ 5 Page