APW7153/A/B 3A 5V 2MHz Synchronous Buck Converter Features General Description * High Efficiency up to 95% - PFM/PWM Mode Operation APW7153/A/B is a 3A synchronous buck converter with integrated 110m power MOSFETs. The APW7153/A/B * * * Adjustable Output Voltage from 0.8V to VIN Integrated 110m High/Low Side MOSFET is designed with a current-mode control scheme; it can convert wide input voltage of 2.6V to 5.5V to the output Programmable Switching Frequency: 300kHz to 2MHz voltage adjustable from 0.8V to 5.5V to provide excellent output voltage regulation. * * * * * * * * * * * * Low Dropout Operation: 100% Duty Cycle Stable with Low ESR Capacitors The APW7153/A/B is equipped with an PFM/PWM mode operation. At light load, the IC operates in the PFM mode Power-On-Reset Detection on VDD and PVDD Integrate Soft-Start and Soft-Off to reduce the switching losses. At heavy load, the IC works in PWM. At PWM mode, the switching frequency is set by Over-Temperature Protection Over-Voltage Protection the external resistor. The APW7153/A/B is also equipped with Power-on-reset, Under-Voltage Protection High/Low Side Current-Limit soft-start, soft-stop, and whole protections (under-voltage, over-voltage, over-temperature and current-limit) into a Power Good Indicator (APW7153A/B) Enable/Shutdown Function single package. This device, available TDFN3x3-10 and SOP-8P provides Small TDFN3x3-10 and SOP-8P Packages Lead Free and Green Devices Available a very compact system solution external components and PCB area. (RoHS Compliant) Simplified Application Circuit VIN Applications * * * LCD Minitor/TV Set-Top Box VDD PVDD DSL, Switch HUB * * VOUT APW7153/A/B Notebook Computer Portable Instrument Pin Configuration APW7153 SHDN/RT 1 GND 2 LX 3 PGND 4 9 Expose Pad APW7153 8 COMP SHDN/RT 1 GND 2 7 FB LX 3 6 VDD LX 4 5 PVDD PGND 5 SOP-8P (Top View) 9 11 Expose Pad APW7153A 10 COMP 9 FB 8 VDD 7 PVDD 6 PVDD 11 Expose Pad APW7153B 10 COMP SHDN/RT 1 GND 2 9 FB LX 3 8 POK LX 4 7 VDD PGND 5 6 PVDD TDFN3X3-10 (Top View) TDFN3X3-10 (Top View) The pin 2 and 4 must be connected to the pin 9 (Exposed Pad) EN/RT 1 GND 2 LX 3 LX 4 PGND 5 11 Expose Pad 10 COMP 9 FB 8 POK 7 VDD 6 PVDD TDFN3X3-10 (Top View) 11 The pin 2 and 5 must be connected to the pin 11 (Exposed Pad) S ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 1 www.anpec.com.tw APW7153/A/B Ordering and Marking Information Package Code QB : TDFN3x3-10 KA : SOP-8P Operating Ambient Temperature Range I : -40 to 85 oC Handling Code TR : Tape & Reel Assembly Material G : Halogen and Lead Free Device APW7153/A/B Assembly Material Handling Code Temperature Range Package Code APW7153/A/B QB: APW 7153 XXXXX APW7153 KA: APW7153 XXXXX APW 7153A XXXXX APW 7153B XXXXX XXXXX - Date Code XXXXX - Date Code Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for MSL classification at lead-free peak reflow temperature. ANPEC defines "Green" to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight). Absolute Maximum Ratings Symbol VVDD, VPVDD VLX (Note 1) Parameter Rating Unit -0.3 ~ 6 V >20ns pulse width -1 ~VPVDD+0.3 V <20ns pulse width -3 ~VPVDD+3 V -0.3 ~ 6 V Input Supply Voltage LX to GND Voltage SHDN/RT, FB, COMP, POK to GND Voltage PGND PGND to GND Voltage PD Power Dissipation TJ Junction Temperature TSTG Storage Temperature TSDR Maximum Lead Soldering Temperature, 10 Seconds -0.3 ~ +0.3 V Internally Limited W 150 o -65 ~ 150 o 260 o C C C Note1: Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Thermal Characteristics Symbol JA JC Parameter Junction-to-Ambient Resistance in Free Air Typical Value Unit (Note 2) TDFN3x3-10 SOP-8P 50 80 o TDFN3x3-10 SOP-8P 10 20 o Junction-to-Case Resistance in Free Air (Note 3) C/W C/W Note 2: JA is measured with the component mounted on a high effective thermal conductivity test board in free air. The exposed pad of TDFN3x3-10 and SOP-8P is soldered directly on the PCB. Note 3: The case temperature is measured at the center of the exposed pad on the underside of the TDFN3x3-10 and SOP-8P packages. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 2 www.anpec.com.tw APW7153/A/B Recommended Operating Conditions (Note 4) Symbol Range Unit VVDD Control and Driver Supply Voltage 2.6~ 5.5 V VPVDD Input Supply Voltage 1. 5~5.5 V VOUT Converter Output Voltage 0.8~5.5 V IOUT Converter Output Current 0~3 TA TJ Parameter Ambient Temperature Junction Temperature A -40 ~ 85 o -40 ~ 125 o C C Note 4: Refer to the typical application circuit. Electrical Characteristics Unless otherwise specified, these specifications apply over VVDD=VPVDD=3.3V, TA= -40 ~ 85 oC. Typical values are at TA=25oC. Symbol Parameter APW7153/A/B Test Conditions Min. Typ. Unit Max. SUPPLY CURRENT VFB=1V - 460 - A IVDD_SDH VDD Shutdown Supply Current SHDN/RT=VDD - - 1 A IVDD_SDL VDD Shutdown Supply Current SHDN/RT=GND - - 10 A 2.3 2.4 2.5 V VDD Debounce Time - 100 - s VDD POR Hysteresis 0.1 0.2 0.3 V PVDD POR Voltage Threshold 1.5 1.6 1.7 V PVDD POR Debounce - 10 - s PVDD POR Hysteresis - 50 - mV Regulated on FB APW7153/B pin APW7153A - 0.8 - - 0.5 - TJ=25C, IOUT=10mA, VDD=5V -0.5 - +0.5 % IOUT=10mA~3A, VDD=2.6~5V -0.8 - +0.8 % 0.3 - 2 MHz 0.8 1 1.2 MHz Maximum Converter's Duty - 100 - % Minimum on Time - 90 - ns IVDD VDD Supply Current POWER-ON-RESET (POR) VDD POR Voltage Threshold VIN Rising REFERENCE VOLTAGE VREF Reference Voltage Output Voltage Accuracy V OSCILLATOR AND DUTY CYCLE FOSC Oscillator Frequency Oscillator Frequency RT=332k POWER MOSFET High Side P-MOSFET Resistance ILX=0.5A, TA=25C - 110 160 m Low Side N-MOSFET Resistance ILX=0.5A, TA=25C - 110 160 m - - 10 A High/Low Side MOSFET Leakage Current Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 3 www.anpec.com.tw APW7153/A/B Electrical Characteristics (Cont.) Unless otherwise specified, these specifications apply over VVDD=VPVDD=3.3V, TA= -40 ~ 85 oC. Typical values are at TA=25oC. Symbol Parameter APW7153/A/B Test Conditions Unit Min. Typ. Max. - 550 - CURRENT-MODE PWM CONVERTER Gm Error Amplifier Transconductance Error Amplifier DC Gain TD COMP=NC A/V - 80 - dB Current Sense Transresistance - 500 - m Dead Time (Note 5) - 20 - ns 4.0 4.5 5.0 A - 160 - C PROTECTIONS ILIM TOTP High Side MOSFET Current-Limit Over-Temperature Trip Point Peak Current (Note 5) Over-Temperature Hysteresis - 50 - C Over-Voltage Protection Threshold 119 125 131 %VOUT Under-Voltage Protection Threshold 44 50 56 % 0.7 - 1.6 A 1 1.5 2 ms - VVDD-0.9 VVDD -0.4 V 85 87.5 90 %VOUT POK Low Hysteresis (POK Goes High) - 5 - %VOUT POK in from Higher (POK Goes High) 110 112.5 115 %VOUT - 5 - %VOUT Power Good Pull Low Resistance - 100 - Power Good Debounce - 0.5 - ms Low Side MOSFET Current-Limit From Drain to Source SOFT-START, ENABLE AND INPUT CURRENTS Soft-Start Time VSHDN SHDN Shutdown Threshold VSHDN > SHDN shutdown Threshold, IC shutdown POK in from Lower (POK Goes High) POK Threshold POK High Hysteresis (POK Goes Low) Note 5: Guarantee by design. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 4 www.anpec.com.tw APW7153/A/B Typical Operating Characteristics Refer to the application circuit in the section "Typical Application Circuits", VIN=5V, TA=25oC, unless otherwise specified. Efficiency vs. Output Current 100 1.8 95 1.6 90 1.4 85 1.2 Efficiency (%) RT=330k for 1MHz 1 0.8 0.6 RT=1.3M for 300kHz 75 70 65 60 0.2 55 0 0 200 400 600 0.1 1 10 RT Resistance, RRT (k) Output Current, IOUT (A) Efficiency vs. Output Current Reference Voltage vs. Supply Voltage 100 820 95 815 85 80 75 70 65 VIN=5V VOUT=3.3V RT=330k 60 55 50 0.01 0.1 1 Output Current, IOUT (A) 810 805 800 795 790 785 780 10 No Switch Quiescent Current vs. Supply Voltage 2 2.5 3 3.5 4 4.5 Supply Voltage, V VDD (V) 5 5.5 Peak Current-Limit vs. Supply Voltage 6 450 Peak Current Limit, ILIM (A) No Switch Quiescent Current, IVDD (A) VIN=5V VOUT=1.8V RT=330k 50 0.01 800 1000 1200 1400 90 Efficiency (%) 80 0.4 Reference Voltage, VREF (mV) Oscillator Frequency, FOSC (MHz) Oscillator Frequency vs. RT Resistance 2 400 350 300 250 5 4 3 2 1 0 200 2 2.5 3 3.5 4 4.5 5 5.5 2.5 Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 3 3.5 4 4.5 5 5.5 Supply Voltage, VVDD (V) Supply Voltage, V VDD (V) 5 www.anpec.com.tw APW7153/A/B Operating Waveforms Start-up with No Load Start-up with 3A Load EN, 2V/div EN, 2V/div VOUT, 1V/div, DC VOUT, 1V/div, DC POK, 5V/div POK, 5V/div IIN, 1A/div IIN, 200mA/div 0.5ms/div 0.5ms/div Load Transient Response Normal Operating VOUT, 50mV/div, AC 3A IOUT, 1A/div VLX, 2V/div Slew rate = 3A/20s 10mA VOUT, 100mV/div, AC IOUT, 1A/div VOUT =1.8V 500ns/div 100s/div Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 6 www.anpec.com.tw APW7153/A/B Pin Description PIN TDFN3x3-10 SOP-8P FUNCTION NAME APW7153 APW7153A APW7153B APW7153 Shutdown/Enable and Oscillator Input. Connecting a resistor to SHDN/RT GND sets the switching Frequency. Pull the pin to VDD to shut down the device. Do leave the pin floating. 1 - 1 1 - 1 - - EN/RT Shutdown/Enable and Oscillator Input. Connecting a resistor to VDD sets the switching Frequency. Pull the pin to GND to shut down the device. Do leave the pin floating. 2 2 2 2 GND Signal Ground. Ground of MOSFET Gate Drivers and Control Circuitry. 3, 4 3, 4 3, 4 3 LX Power Switching Output. LX is the Junction of the high-side and low-side Power MOSFETs to supply power to the output LC filter. 5 5 5 4 PGND Power Ground. The Source of the N-channel power MOSFET. Connect this pin to the system ground with lowest impedance. 6, 7 6 6 5 PVDD Power Input. PVDD supplies the step-down converter switches. Connecting a ceramic bypass capacitor from PVDD to PGND to eliminate switching noise and voltage ripple on the input to the IC. 8 7 7 6 VDD Control circuitry supply Input. VDD supplies the control circuitry, gate drivers. Connecting a ceramic bypass capacitor from VDD to GND to eliminate switching noise and voltage ripple on the input to the IC. - 8 8 - POK Power Good Output. This pin is open-drain logic output that is pulled to ground when the output voltage is not within 12.5% of regulation point. 9 9 9 7 FB Output Feedback Input. The APW7153/A senses the feedback voltage via FB and regulates the voltage at 0.8V. Connecting FB with a resistor-divider from the converter's output sets the output voltage. 10 10 10 8 COMP Output of the error amplifier. Connect a series RC network from COMP to GND to compensate the regulation control loop. In some cases, an additional capacitor from COMP to GND is required. 11 11 11 9 Exposed Pad Connect the exposed pad to the system ground plan with large copper area for dissipating heat into the ambient air. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 7 www.anpec.com.tw APW7153/A/B Block Diagram APW7153 VDD PVDD Current Sense Amplifier LOC OverTemperature Protection Power-OnReset Current -Limit Zero Crossing Amplifier POR 1V 0.4 OTP OVP Fault Logics UVP Inhibit Soft-Start COMP Slope Compensation VREF 0.8V LX Gate Driver Gat e Current Compartor Error Amplifier Gm FB Gate Control PGND LOC Current Sense Amplifier Oscillator Shutdown GND SHDN/RT APW7153A VDD 7 PVDD 6 Current Sense Amplifier LOC OverTemperature Protection Power-OnReset Current -Limit Zero Crossing Comparator POR 0.625V OTP OVP Fault Logics 0.25V 4 LX UVP Inhibit 0.5625V 0.4375V Soft-Start Current Compartor Error Amplifier Gm FB 9 VREF 0.5V Gate Control Slope Compensation COMP 10 Oscillator Shutdown Gate Driver Gat e 5 PGND LOC Current Sense Amplifier 2 GND 1 8 POK Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 3 LX EN/RT 8 www.anpec.com.tw APW7153/A/B Block Diagram APW7153B VDD 7 PVDD 6 Current Sense Amplifier LOC OverTemperature Protection Power-OnReset Current -Limit Zero Crossing Comparator POR 1V OTP OVP Fault Logics 0.4V 4 LX UVP Inhibit 0.9V FB 9 Soft-Start Current Compartor Error Amplifier Gm 0.7V Gate Control VREF 0.8V Slope Compensation COMP 10 Oscillator Shutdown 1 POK SHDN/RT 9 Gate Driver Gat e 5 PGND LOC Current Sense Amplifier 2 8 Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 3 LX GND www.anpec.com.tw APW7153/A/B Typical Application Circuit L1 2.2H VIN 5V CIN 22F PVDD R4 2R2 CFF 22pF VDD R3 1M VOUT 1.8V/3A LX C2 1F R1 25k COUT 22Fx2 FB APW7153 RT 332k Cc 100pF Rc COMP SHDN/RT ON R2 20k 30k GND OFF PGND VIN 5V 6 CIN 22F R3 1.8M R5 100k L1 2.2H PVDD LX VOUT 1.8V/3A 3,4 R4 2R2 CFF 22pF 7 VDD C2 1F FB 1 OFF POK COMP 10 GND VIN 5V 6 CIN 22F R3 1M R5 100k Rc 30k PGND L1 2.2H PVDD LX CFF 22pF FB 1 POK COMP 10 SHDN/RT GND OFF 5 R1 25k COUT 22Fx2 9 APW7153B ON Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 VOUT 1.8V/3A 3,4 7 VDD C2 1F 8 R2 15k 2 R4 2R2 RT 332k Cc 100pF EN/RT ON 5 COUT 22Fx2 9 APW7153A 8 R1 39k 2 Rc Cc 100pF R2 20k 30k PGND 10 www.anpec.com.tw APW7153/A/B Function Description power MOSFETs, allowing the devices to cool. The thermal sensor allows the converters to start a start-up pro- VDD and PVDD Power-On-Reset (POR) The APW7153/A/B keeps monitoring the voltage on VDD cess and to regulate the output voltage again after the junction temperature cools by 50oC. The OTP is designed and PVDD pins to prevent wrong logic operations which may occur when VDD or PVDD voltage is not high enough with a 50oC hysteresis to lower the average TJ during continuous thermal overload conditions, increasing life- for internal control circuitry to operate. The VDD POR rising threshold is 2.4V (typical) with 0.2V hysteresis and time of the APW7153/A/B. PVDD POR rising threshold is 1.7V with 0.05V hysteresis. During start-up, the VDD and PVDD voltage must exceed Current-Limit Protection the enable voltage threshold. Then, the IC starts a startup process and ramps up the output voltage to the volt- The APW7153/A/B monitors the output current, flows through the high-side and low-side power MOSFETs, and age target. limits the current peak at current-limit level to prevent the IC from damaging during overload, short-circuit, and overvoltage conditions. Typical high side power MOSFET current-limit is 4.5A, and low side MOSFET current-limit is 1.6A maximum. Output Under-Voltage Protection (UVP) In the operational process, if a short-circuit occurs, the output voltage will drop quickly. Before the current-limit circuit responds, the output voltage will fall out of the required regulation range. The under-voltage continually monitors the FB voltage after soft-start is completed. If a Soft-Start The APW7153/A/B has a built-in soft-start to control the rise rate of the output voltage and limit the input current load step is strong enough to pull the output voltage lower than the under-voltage threshold, the IC shuts down con- surge during start-up. During soft-start, an internal volt- verter's output. The under-voltage threshold is 50% of the nominal out- age ramp connected to one of the positive inputs of the error amplifier, rises up from 0V to 0.95V to replace the put voltage. The under-voltage comparator has a built-in 3s noise filter to prevent the chips from wrong UVP shut- reference voltage, VREF until the voltage ramp reaches the reference voltage. During soft-start without output over- down being caused by noise. APW7153/A/B will be latched after under-voltage protection. voltage, the APW7153/A/B converter's sinking capability is disabled until the output voltage reaches the voltage Over-Voltage Protection (OVP) target. The over-voltage function monitors the output voltage by Soft-Off FB pin. When the FB voltage increases over 125% of the reference voltage due to the high-side MOSFET failure or At the moment of shutdown controlled by SHDN/RT signal, under-voltage event or over-temperature protection, the APW7153/A/B initiates a soft-stop process for other reasons, the over-voltage protection comparator will force the low-side MOSFET gate driver to be high. to discharge the output voltage in the output capacitors. Certainly, the load current also discharges the output This action actively pulls down the output voltage and eventually attempts to blow the internal bonding wires. voltage. During soft-stop, the internal voltage ramp (VRAMP) falls down rises from 0.95V to 0V to replace the reference As soon as the output voltage is within regulation, the OVP comparator is disengaged. The chip will restore its normal operation. voltage. Therefore, the output voltage falls down slowly at the light load. After the soft-stop interval elapses, the soft- Over-Temperature Protection (OTP) stop process ends and the IC turns on the low-side power MOSFET. The over-temperature circuit limits the junction temperature of the APW7153/A/B. When the junction temperature exceeds TJ=+160oC, a thermal sensor turns off the both Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 11 www.anpec.com.tw APW7153/A/B Function Description (Cont.) Switching Frequency and Shutdown/Enable The SHDN/RT pin is a multi-function pin that is used to control the switching frequency and Shutdown/Enable function of APW7153/A/B. The switching frequency is set by the external resistor that is connected between SHDN/ RT and GND. The value of the resistor sets the ramp current that is used to charge and discharge an internal timing capacitor within the oscillator. The SHDN/RT pin also provides Shutdown/Enable function. Pulling the pin to VDD or GND, APW7153/A/B initiates a soft-stop process and shutdown the IC. Power Good Indicator (APW7153A/B) POK is actively held low in shutdown and soft-start status. In the soft-start process, the POK is an open-drain. When the soft-start is finished, the POK is released. In normal operation, the POK window is from 87.5% to 112.5% of the converter reference voltage. When the output voltage has to stay within this window, POK signal will become high after 0.5ms internal delay. When the output voltage outruns 85% or 115% of the target voltage, POK signal will be pulled low immediately. In order to prevent false POK drop, capacitors need to parallel at the output to confine the voltage deviation with severe load step transient. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 12 www.anpec.com.tw APW7153/A/B Application Information Input Capacitor Selection shown in "Typical Application Circuits". A suggestion of maximum value of R2 is 300k to keep the minimum Because buck converters have a pulsating input current, a low ESR input capacitor is required. This results in the current that provides enough noise rejection ability through the resistor divider. The output voltage can be calculated best input voltage filtering, minimizing the interference with other circuits caused by high input voltage spikes. as below: R1 VOUT = VREF 1 + R2 Also, the input capacitor must be sufficiently large to stabilize the input voltage during heavy load transients. For good input voltage filtering, usually a 22F input capacitor is sufficient. It can be increased without any limit for VOUT better input voltage filtering. Ceramic capacitors show better performance because of the low ESR value, and R11M FB they are less sensitive against voltage transients and spikes compared to tantalum capacitors. Place the input R2 300K APW7153 GND capacitor as close as possible to the input and GND pin of the device for better performance. Output Capacitor Selection Inductor Selection The current-mode control scheme of the APW7153 allows the use of tiny ceramic capacitors. The higher ca- For high efficiencies, the inductor should have a low dc resistance to minimize conduction losses. Especially at pacitor value provides the good load transients response. Ceramic capacitors with low ESR values have the lowest high-switching frequencies the core material has a higher impact on efficiency. When using small chip inductors, output voltage ripple and are recommended. If required, the efficiency is reduced mainly due to higher inductor core losses. This needs to be considered when select- tantalum capacitors may be used as well. The output ripple is the sum of the voltages across the ESR and the ing the appropriate inductor. The inductor value determines the inductor ripple current. The larger the inductor ideal output capacitor. value, the smaller the inductor ripple current and the lower the conduction losses of the converter. Conversely, larger VOUT inductor values cause a slower load transient response. A reasonable starting point for setting ripple current, IL, 1 ESR + 8 FSW COUT When choosing the input and output ceramic capacitors, choose the X5R or X7R dielectric formulations. These is 40% of maximum output current. The recommended inductor value can be calculated as below: V VOUT 1 - OUT VIN L FSW IL V VOUT 1 - OUT VIN FSW L dielectrics have the best temperature and voltage characteristics of all the ceramics for a given value and size. VIN IIN IP-FET IL(MAX) = IOUT(MAX) + 1/2 x IL IL To avoid saturation of the inductor, the inductor should be rated at least for the maximum output current of the con- CIN verter plus the inductor ripple current. P-FET VOUT LX N-FET Output Voltage Setting IOUT ESR COUT In the adjustable version, the output voltage is set by a resistive divider. The external resistive divider is connected to the output, allowing remote voltage sensing as Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 13 www.anpec.com.tw APW7153/A/B Application Information (Cont.) Output Capacitor Selection (Cont.) Via To GND GND IPEAK IL LX L1 IOUT Via To VOUT Rc 1 10 2 9 3 8 4 7 5 6 CFF R1 FB C2 ILIM Cc R4 RT R2 IL Via To GND IP-FET C2 C1 PGND VOUT VIN Figure 1. APW7153/A/B Layout Suggestion Recommended Minimum Footprint Layout Considerations Layout For all switching power supplies, the layout is an important step in the design; especially at high peak currents Package outline and switching frequencies. If the layout is not carefully done, the regulator might show noise problems and duty 0.06 cycle jitter. Unit: Inch 0.04 1. The input capacitor should be placed close to the PVDD and GND. Connect the capacitor and PVDD/GND with short and wide trace without any via holes for good input voltage filtering. The distance between PVDD/GND to 0.1 capacitor less than 2mm respectively is recommended. 2. To minimize copper trace connections that can inject 0.011 1 10 2 9 3 8 4 7 5 6 0.011 0.06 noise into the system, the inductor should be placed as close as possible to the LX pin to minimize the noise 0.029 The via diameter = 0.012 Hole size = 0.008 TDFN3x3-10 coupling into other circuits. 3. The output capacitor should be place closed to VOUT 0.024 8 7 6 5 0.072 and GND. 4. Keep the sensitive small signal nodes (FB, COMP) away from switching nodes (LX) on the PCB. Therefore place the feedback divider and the feedback compensa- 0.138 GND pin of the IC using a dedicated ground trace. 5. A star ground connection or ground plane minimizes 0.118 0.212 tion network close to the IC to avoid switching noise. Connect the ground of feedback divider directly to the ground shifts and noise is recommended. 1 2 0.050 3 4 Unit : Inch SOP-8P Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 14 www.anpec.com.tw APW7153/A/B Package Information TDFN3x3-10 A b E D Pin 1 A1 D2 A3 L K E2 Pin 1 Corner e S Y M B O L TDFN3x3-10 MILLIMETERS MIN. INCHES MAX. MIN. MAX. A 0.70 0.80 0.028 0.031 A1 0.00 0.05 0.000 0.002 0.30 0.007 0.012 0.122 A3 b 0.20 REF 0.18 0.008 REF D 2.90 3.10 0.114 D2 2.20 2.70 0.087 0.106 0.122 0.069 E 2.90 3.10 0.114 E2 1.40 1.75 0.055 0.50 0.012 e 0.50 BSC L 0.30 K 0.20 0.020 BSC 0.020 0.008 Note : 1. Followed from JEDEC MO-229 VEED-5. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 15 www.anpec.com.tw APW7153/A/B Package Information SOP-8P -T- SEATING PLANE < 4 mils D SEE VIEW A h X 45o E THERMAL PAD E1 E2 D1 c A1 0.25 A2 A b e GAUGE PLANE SEATING PLANE L VIEW A S Y M B O L A SOP-8P INCHES MILLIMETERS MAX. MIN. MIN. MAX. 1.60 A1 0.00 0.063 0.15 0.000 0.006 0.049 A2 1.25 b 0.31 0.51 0.012 0.020 c 0.17 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 D1 2.50 3.50 0.098 0.138 E 5.80 6.20 0.228 0.244 0.157 0.118 E1 3.80 4.00 0.150 E2 2.00 3.00 0.079 e 1.27 BSC 0.050 BSC h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 0o C 8o C 0oC 8o C Note : 1. Followed from JEDEC MS-012 BA. 2. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion or gate burrs shall not exceed 6 mil per side . 3. Dimension "E" does not include inter-lead flash or protrusions. Inter-lead flash and protrusions shall not exceed 10 mil per side. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 16 www.anpec.com.tw APW7153/A/B Carrier Tape & Reel Dimensions P0 P2 P1 A B0 W F E1 OD0 K0 A0 A OD1 B B T SECTION A-A SECTION B-B H A d T1 Application TDFN3x3-10 A H T1 C d D W E1 F 330.02.00 50 MIN. 12.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 12.00.30 1.750.10 5.50.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.00.05 1.5+0.10 -0.00 1.5 MIN. 0.6+0.00 -0.40 3.300.20 3.300.20 1.300.20 4.00.10 8.00.10 A H T1 C d D W E1 F 330.02.00 50 MIN. 12.4+2.00 -0.00 13.0+0.50 -0.20 1.5 MIN. 20.2 MIN. 12.00.30 1.750.10 5.50.05 P0 P1 P2 D0 D1 T A0 B0 K0 2.00.05 1.5+0.10 -0.00 1.5 MIN. 0.6+0.00 -0.40 6.400.20 5.200.20 2.100.20 Application SOP-8P 4.00.10 8.00.10 (mm) Devices Per Unit Package Type Unit Quantity TDFN3x3-10 Tape & Reel 3000 SOP-8P Tape & Reel 2500 Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 17 www.anpec.com.tw APW7153/A/B Taping Direction Information TDFN3x3-10 USER DIRECTION OF FEED SOP-8P USER DIRECTION OF FEED Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 18 www.anpec.com.tw APW7153/A/B Classification Profile Supplier TpTc User TpTc TC TC -5oC User tp Supplier tp Tp Temperature Max. Ramp Max. Ramp TL Tsmax tp Up Rate = 3oC/s Down Rate = 6oC/s TC -5oC t Preheat Area Tsmin tS 25 Time 25oC to Peak Time Classification Reflow Profiles Profile Feature Sn-Pb Eutectic Assembly Pb-Free Assembly 100 C 150 C 60-120 seconds 150 C 200 C 60-120 seconds 3 C/second max. 3C/second max. 183 C 60-150 seconds 217 C 60-150 seconds See Classification Temp in table 1 See Classification Temp in table 2 Time (tP)** within 5C of the specified classification temperature (Tc) 20** seconds 30** seconds Average ramp-down rate (Tp to Tsmax) 6 C/second max. 6 C/second max. 6 minutes max. 8 minutes max. Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) Average ramp-up rate (Tsmax to TP) Liquidous temperature (TL) Time at liquidous (tL) Peak package body Temperature (Tp)* Time 25C to peak temperature * Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum. ** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum. Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 19 www.anpec.com.tw APW7153/A/B Classification Reflow Profiles (Cont.) Table 1. SnPb Eutectic Process - Classification Temperatures (Tc) Package Thickness <2.5 mm 2.5 mm Volume mm <350 235 C 220 C 3 Volume mm 350 220 C 220 C 3 Table 2. Pb-free Process - Classification Temperatures (Tc) Package Thickness <1.6 mm 1.6 mm - 2.5 mm 2.5 mm Volume mm <350 260 C 260 C 250 C 3 Volume mm 350-2000 260 C 250 C 245 C 3 Volume mm >2000 260 C 245 C 245 C 3 Reliability Test Program Test item SOLDERABILITY HOLT PCT TCT HBM MM Latch-Up Method JESD-22, B102 JESD-22, A108 JESD-22, A102 JESD-22, A104 MIL-STD-883-3015.7 JESD-22, A115 JESD 78 Description 5 Sec, 245C 1000 Hrs, Bias @ Tj=125C 168 Hrs, 100%RH, 2atm, 121C 500 Cycles, -65C~150C VHBM2KV VMM200V 10ms, 1tr100mA Customer Service Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 2F, No. 11, Lane 218, Sec 2 Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan Tel : 886-2-2910-3838 Fax : 886-2-2917-3838 Copyright ANPEC Electronics Corp. Rev. A.6 - Aug., 2012 20 www.anpec.com.tw