Document Number: 91027 www.vishay.com
S11-0510-Rev. B, 21-Mar-11 1
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Power MOSFET
IRF620, SiHF620
Vishay Siliconix
FEATURES
Dynamic dV/dt Rating
Repetitive Avalanche Rated
•Fast Switching
Ease of Paralleling
Simple Drive Requirements
Compliant to RoHS Directive 2002/95/EC
DESCRIPTION
Third generation Power MOSFETs from Vishay provide the
designer with the best combination of fast switching,
ruggedized device design, low on-resistance and
cost-effectiveness.
The TO-220AB package is universally preferred for all
commercial-industrial applications at power dissipation
levels to approximately 50 W. The low thermal resistance
and low package cost of the TO-220AB contribute to its
wide acceptance throughout the industry.
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. VDD = 50 V, starting TJ = 25 °C, L = 6.1 mH, Rg = 25 , IAS = 5.2 A (see fig. 12).
c. ISD 5.2 A, dI/dt 95 A/μs, VDD VDS, TJ 150 °C.
d. 1.6 mm from case.
PRODUCT SUMMARY
VDS (V) 200
RDS(on) ()V
GS = 10 V 0.80
Qg (Max.) (nC) 14
Qgs (nC) 3.0
Qgd (nC) 7.9
Configuration Single
N-Channel MOSFET
G
D
S
TO-220AB
GD
S
Available
RoHS*
COMPLIANT
ORDERING INFORMATION
Package TO-220AB
Lead (Pb)-free IRF620PbF
SiHF620-E3
SnPb IRF620
SiHF620
ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)
PARAMETER SYMBOL LIMIT UNIT
Drain-Source Voltage VDS 200 V
Gate-Source Voltage VGS ± 20
Continuous Drain Current VGS at 10 V TC = 25 °C ID
5.2
ATC = 100 °C 3.3
Pulsed Drain CurrentaIDM 18
Linear Derating Factor 0.40 W/°C
Single Pulse Avalanche EnergybEAS 110 mJ
Repetitive Avalanche CurrentaIAR 5.2 A
Repetitive Avalanche EnergyaEAR 5.0 mJ
Maximum Power Dissipation TC = 25 °C PD50 W
Peak Diode Recovery dV/dtcdV/dt 5.0 V/ns
Operating Junction and Storage Temperature Range TJ, Tstg - 55 to + 150 °C
Soldering Recommendations (Peak Temperature) for 10 s 300d
Mounting Torque 6-32 or M3 screw 10 lbf · in
1.1 N · m
* Pb containing terminations are not RoHS compliant, exemptions may apply
www.vishay.com Document Number: 91027
2S11-0510-Rev. B, 21-Mar-11
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF620, SiHF620
Vishay Siliconix
Notes
a. Repetitive rating; pulse width limited by maximum junction temperature (see fig. 11).
b. Pulse width 300 μs; duty cycle 2 %.
THERMAL RESISTANCE RATINGS
PARAMETER SYMBOL TYP. MAX. UNIT
Maximum Junction-to-Ambient RthJA -62
°C/WCase-to-Sink, Flat, Greased Surface RthCS 0.50 -
Maximum Junction-to-Case (Drain) RthJC -2.5
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT
Static
Drain-Source Breakdown Voltage VDS VGS = 0 V, ID = 250 μA 200 - - V
VDS Temperature Coefficient VDS/TJ Reference to 25 °C, ID = 1 mA - 0.29 - V/°C
Gate-Source Threshold Voltage VGS(th) VDS = VGS, ID = 250 μA 2.0 - 4.0 V
Gate-Source Leakage IGSS V
GS = ± 20 V - - ± 100 nA
Zero Gate Voltage Drain Current IDSS
VDS = 200 V, VGS = 0 V - - 25 μA
VDS = 160 V, VGS = 0 V, TJ = 125 °C - - 250
Drain-Source On-State Resistance RDS(on) V
GS = 10 V ID = 3.1 Ab- - 0.80
Forward Transconductance gfs VDS = 50 V, ID = 3.1 A 1.5 - - S
Dynamic
Input Capacitance Ciss VGS = 0 V,
VDS = 25 V,
f = 1.0 MHz, see fig. 5
- 260 -
pFOutput Capacitance Coss - 100 -
Reverse Transfer Capacitance Crss -30-
Total Gate Charge Qg
VGS = 10 V ID = 4.8 A, VDS = 160 V,
see fig. 6 and 13b
--14
nC Gate-Source Charge Qgs --3.0
Gate-Drain Charge Qgd --7.9
Turn-On Delay Time td(on)
VDD = 100 V, ID = 4.8 A,
Rg = 18 , RD = 20 , see fig. 10b
-7.2-
ns
Rise Time tr -22-
Turn-Off Delay Time td(off) -19-
Fall Time tf -13-
Internal Drain Inductance LD Between lead,
6 mm (0.25") from
package and center of
die contact
-4.5-
nH
Internal Source Inductance LS-7.5-
Drain-Source Body Diode Characteristics
Continuous Source-Drain Diode Current IS
MOSFET symbol
showing the
integral reverse
p - n junction diode
--5.2
A
Pulsed Diode Forward CurrentaISM --18
Body Diode Voltage VSD TJ = 25 °C, IS = 5.2 A, VGS = 0 Vb--1.8V
Body Diode Reverse Recovery Time trr TJ = 25 °C, IF = 4.8 A, dI/dt = 100 A/s- 150 300 ns
Body Diode Reverse Recovery Charge Qrr - 0.91 1.8 μC
Forward Turn-On Time ton Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)
D
S
G
S
D
G
Document Number: 91027 www.vishay.com
S11-0510-Rev. B, 21-Mar-11 3
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF620, SiHF620
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
Fig. 1 - Typical Output Characteristics, TC = 25 °C
Fig. 2 - Typical Output Characteristics, TC = 150 °C
Fig. 3 - Typical Transfer Characteristics
Fig. 4 - Normalized On-Resistance vs. Temperature
91027_01
Bottom
To p
VGS
15 V
10 V
8.0 V
7.0 V
6.0 V
5.5 V
5.0 V
4.5 V
20 µs Pulse Width
TC = 25 °C
4.5 V
V
DS
, Drain-to-Source Voltage (V)
I
D
, Drain Current (A)
100101
101
100
10-1
10-2
10-2 10-1
101
100
10-1
100101
V
DS,
Drain-to-Source Voltage (V)
I
D
, Drain Current (A)
4.5 V
Bottom
To p
VGS
15 V
10 V
8.0 V
7.0 V
6.0 V
5.5 V
5.0 V
4.5 V
20 µs Pulse Width
TC = 150 °C
91027_02
10-2
10-1
20 µs Pulse Width
VDS = 50 V
101
100
10-1
ID, Drain Current (A)
VGS, Gate-to-Source Voltage (V)
5678910
4
25 °C
150 °C
91027_03
I
D
= 4.8 A
V
GS
= 10 V
3.0
0.0
0.5
1.0
1.5
2.0
2.5
T
J,
Junction Temperature (°C)
R
DS(on)
, Drain-to-Source On Resistance
(Normalized)
91027_04
- 60 - 40 - 20 0 20 40 60 80 100 120 140 160
www.vishay.com Document Number: 91027
4S11-0510-Rev. B, 21-Mar-11
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF620, SiHF620
Vishay Siliconix
Fig. 5 - Typical Capacitance vs. Drain-to-Source Voltage
Fig. 6 - Typical Gate Charge vs. Gate-to-Source Voltage
Fig. 7 - Typical Source-Drain Diode Forward Voltage
Fig. 8 - Maximum Safe Operating Area
750
600
450
0
150
300
100101
Capacitance (pF)
V
DS,
Drain-to-Source Voltage (V)
Ciss
Crss
Coss
VGS = 0 V, f = 1 MHz
Ciss = Cgs + Cgd, Cds Shorted
Crss = Cgd
Coss = Cds + Cgd
91027_05
Q
G
, Total Gate Charge (nC)
V
GS
, Gate-to-Source Voltage (V)
20
16
12
8
0
4
0315
9
I
D
= 4.8 A
V
DS
= 40 V
V
DS
= 100 V
For test circuit
see figure 13
V
DS
= 160 V
91027_06
12
6
101
100
VSD, Source-to-Drain Voltage (V)
ISD, Reverse Drain Current (A)
0.5 1.5
1.31.00.8
25 °C
150 °C
V
GS
= 0 V
91027_07
10 µs
100 µs
1 ms
10 ms
Operation in this area limited
by RDS(on)
VDS, Drain-to-Source Voltage (V)
ID, Drain Current (A)
TC = 25 °C
TJ = 150 °C
Single Pulse
102
0.1
2
5
0.1
1
2
5
10
2
5
25
110
25 102
25 103
25
91027_08
Document Number: 91027 www.vishay.com
S11-0510-Rev. B, 21-Mar-11 5
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF620, SiHF620
Vishay Siliconix
Fig. 9 - Maximum Drain Current vs. Case Temperature
Fig. 10a - Switching Time Test Circuit
Fig. 10b - Switching Time Waveforms
Fig. 11 - Maximum Effective Transient Thermal Impedance, Junction-to-Case
Fig. 12a - Unclamped Inductive Test Circuit Fig. 12b - Unclamped Inductive Waveforms
ID, Drain Current (A)
TC, Case Temperature (°C)
0.0
1.0
2.0
3.0
4.0
5.0
25 1501251007550
91027_09
6.0
Pulse width 1 µs
Duty factor 0.1 %
RD
VGS
RG
D.U.T.
10 V
+
-
VDS
VDD
VDS
VGS
10
1
0.1
10-2
10-5 10-4 10-3 10-2 0.1 1 10
PDM
t1
t2
t
1
, Rectangular Pulse Duration (s)
Thermal Response (Z
thJC
)
Notes:
1. Duty Factor, D = t1/t2
2. Peak Tj = PDM x ZthJC + TC
Single Pulse
(Thermal Response)
0 0.5
0.2
0.1
0.05
0.02
0.01
91027_11
R
G
I
AS
0.01 Ω
t
p
D.U.T.
L
V
DS
+
-V
DD
A
10 V
Var y t
p
to obtain
required I
AS
I
AS
V
DS
V
DD
V
DS
t
p
www.vishay.com Document Number: 91027
6S11-0510-Rev. B, 21-Mar-11
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF620, SiHF620
Vishay Siliconix
Fig. 12c - Maximum Avalanche Energy vs. Drain Current
Fig. 13a - Basic Gate Charge Waveform Fig. 13b - Gate Charge Test Circuit
300
0
50
100
150
200
250
25 150
125
10075
50
Starting T
J
, Junction Temperature (°C)
E
AS
, Single Pulse Energy (mJ)
Bottom
To p
ID
2.3 A
3.3 A
5.2 A
VDD = 50 V
91027_12c
QGS QGD
QG
V
G
Charge
10 V
D.U.T.
3 mA
VGS
VDS
IGID
0.3 µF
0.2 µF
50 kΩ
12 V
Current regulator
Current sampling resistors
Same type as D.U.T.
+
-
Document Number: 91027 www.vishay.com
S11-0510-Rev. B, 21-Mar-11 7
This datasheet is subject to change without notice.
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
IRF620, SiHF620
Vishay Siliconix
Fig. 14 - For N-Channel
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see http://www.vishay.com/ppg?91027.
P.W. Period
dI/dt
Diode recovery
dV/dt
Ripple 5 %
Body diode forward drop
Re-applied
voltage
Reverse
recovery
current
Body diode forward
current
VGS = 10 Va
ISD
Driver gate drive
D.U.T. lSD waveform
D.U.T. VDS waveform
Inductor current
D = P.W.
Period
+
-
+
+
+
-
-
-
Peak Diode Recovery dV/dt Test Circuit
VDD
dV/dt controlled by Rg
Driver same type as D.U.T.
ISD controlled by duty factor “D”
D.U.T. - device under test
D.U.T. Circuit layout considerations
Low stray inductance
Ground plane
Low leakage inductance
current transformer
Rg
Note
a. VGS = 5 V for logic level devices
VDD
Document Number: 71195 www.vishay.com
Revison: 01-Nov-10 1
Package Information
Vishay Siliconix
TO-220AB
Note
* M = 1.32 mm to 1.62 mm (dimension including protrusion)
Heatsink hole for HVM
* M
3
2
1
L
L(1)
D
H(1)
Q
Ø P
A
F
J(1)
b(1)
e(1)
e
E
b
C
MILLIMETERS INCHES
DIM. MIN. MAX. MIN. MAX.
A 4.25 4.65 0.167 0.183
b 0.69 1.01 0.027 0.040
b(1) 1.20 1.73 0.047 0.068
c 0.36 0.61 0.014 0.024
D 14.85 15.49 0.585 0.610
E 10.04 10.51 0.395 0.414
e 2.41 2.67 0.095 0.105
e(1) 4.88 5.28 0.192 0.208
F 1.14 1.40 0.045 0.055
H(1) 6.09 6.48 0.240 0.255
J(1) 2.41 2.92 0.095 0.115
L 13.35 14.02 0.526 0.552
L(1) 3.32 3.82 0.131 0.150
Ø P 3.54 3.94 0.139 0.155
Q 2.60 3.00 0.102 0.118
ECN: X10-0416-Rev. M, 01-Nov-10
DWG: 5471
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.