LANGUAGE
JAPANESE
ENGLISH
REV.
A
B
C
SHEET
1-15
1-20
1-20
REVISE ON PC ONLY
TITLE:
0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
改訂
REVISED
J2015-1609
15/06/08 A.ISHII
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DESIGN CONTROL
J
STATUS
WRITTEN
BY:
H.IIJIMA
CHECKED
BY:
K.TAKAHASHI
APPROVED
BY:
K.MORIKAWA
DATE: YR/MO/DAY
2006/03/17
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
1 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
【1.適用範囲 SCOPE
本仕様書は、 0.5m ピッチ FFC 基板 コネクタ について規定する。
This specification covers the 0.5mm PITCH FFC TO BOARD CONNECTOR series
【2.製品名称及び型番 PRODUCT NAME AND PART NUMBER
Product Name
Material Number
ハウジングアッセンブリ
Housing Assembly (RA Type)
501864-**21
501864-**21 テーピング梱包
Embossed Tape Package for 501864-**21
501864-**80
プラグジャケッ
Plug Jacket
501783-**09
プラグジャケットカバー
Plug Jacket Cover
501784-**09
*:図面参照 Refer to the drawings.
【3.定格 RATINGS
Item
Standard
最大許容電圧
Rated Voltage (MAX.)
50 V*3
[AC (実効値 rms) /DC]
最大許容電流
Rated Current (MAX.)
0.5 A*3
使用温度範囲*1
Ambient Temperature Range
-40 +85*2*3
保管条件
Storage condition
温度
Temperature
-10℃~+50
湿度
Humidity
85R.H.以下(但し結露なきこと)
85%R.H. MAX.(No condensation)
期間
Term
出荷後6ヶ月以内(開封の場合)
For 6 months after shipping (unopened package)
*1:基板実装後の無通電状態は、使用温度範囲が適用されます。
Non-operating connectors after reflow must follow the operating temperature range condition.
*2:通電による温度上昇分を含む。
Including terminal temperature rise.
*3:使用FFCも本定格を満足すること。
FFC must be met ratings specified in this standard.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
2 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
【4.性 PERFORMANCE
4-1.電気的性能 Electrical Performance
Item
Test Condition
Requirement
4-1-1
Contact
Resistance
適合FFCハーネスを嵌合させ、開放電圧 20mV 以下、
短絡電流 10mA 以下 にて測定する。
(JIS C5402-2-1)
Mate applicable FFC Harness, measure by dry circuit,
20mV MAX., 10mA MAX.
(JIS C5402-2-1)
40 milliohm MAX.
4-1-2
Insulation
Resistance
適合FFCハーネスを嵌合させ、隣接するターミナル間
及びターミナル、アース間にDC 500V を印加し測定
する。
(JIS C5402-3-1/MIL-STD-202 験法 302)
Mate applicable FFC Harness and apply 500V DC
between adjacent terminal and ground.
(JIS C5402-3-1/MIL-STD-202 Method 302)
50 Megohm MIN.
4-1-3
Dielectric
Strength
適合FFCハーネスを嵌合させ、隣接するターミナル間
及びターミナル、アース間に、AC 250V(実効値) 1
分間 印加する。
(JIS C5402-4-1/MIL-STD-202 験法 301)
Mate applicable FFC Harness, apply 250V AC (rms) for
1 minute between adjacent terminal or ground.
(JIS C5402-4-1/MIL-STD-202 Method 301)
異状なきこと
No Breakdown
4-2. 機械的性能 Mechanical Performance
Item
Test Condition
Requirement
4-2-1
挿入・抜去力
Insertion Force/
Withdrawal Force
ロックを解除した状態にて、毎分 25±3 mm
速さで挿入・抜去を行う。
Insert and withdraw connectors, at the speed rate
of 25±3 mm per minute.
6項参照
Refer to paragraph 6
4-2-1
強制抜去力
Compulsion
Withdrawal
Force
適合FFCハーネスを嵌合させ、ロックを解除せず
に毎分 25±3 mm の速さで軸方向にを引き抜く。
Mate applicable FFC Harness, apply axial pull out
force at the speed rate of 25±3 mm per minute.
9.8 N{ 1.0 kgf} MINIMUM
4-2-3
端子保持力
Terminal/Housing
Retention Force
各端子を毎分 25±3mm の速さで引き抜く。
Apply axial pull out force at the speed rate of
25±3 mm/minute on the terminal assembled in
the housing.
0.5N {0.05kgf} MIN.
4-2-4
金具保持力
Fitting nail /
Housing
Retention Force
各金具を毎分 25±3mm の速さで引き抜く。
Apply axial pull out force at the speed rate of
25±3 mm/minute on the fitting nail assembled in
the housing.
1.0N {0.10kgf} MIN.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
3 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
4-3.そ Environmental Performance and Others
Item
Test Condition
Requirement
4-3-1
繰り返し挿抜
Repeated
Mate / Un-matel
無通電状態にて1分間 10回以下 速さ
で挿入、抜去を 20 繰り返す。
When mated up to 20 cycles repeatedly
at the speed rate of less than 10 cycles
per minute.
接触抵抗
Contact
Resistance
60 milliohm
MAX.
4-3-2
Temperature Rise
適合FFCハーネスを嵌合させ最大許容電流を
通電し、コネクタの温度上昇分を測定する。
(UL 498)
Mate applicable FFC and measure the
temperature rise of contact when the
maximum AC rated current is passed.
(UL 498)
温度上昇
Temperature
Rise
30 °C MAX.
4-3-3
Vibration
DC 1mA 通電状態にて、嵌合軸を含む互い
垂直な 3方向 に掃引割合 105510Hz/分、
全振幅 1.5mm の振動を 2時間 加える。
(JIS C 60068-2-6 /MIL-STD-202 験法 201)
Mate applicable FPC. Apply 0.1mA DC and
subject to the following vibration conditions in
each of 3 mutually perpendicular axes.
Amplitude : 1.5 mm P-P
Frequency : 10-55-10 Hz / minute.
Duration : 2 hours in each
(JIS C 60068-2-6 /MIL-STD-202, Method 201)
Appearance
異状なきこと
No Damage
接触抵抗
Contact
Resistance
60 milliohm
MAX.
Discontinuity
1 microsecond
MAX
4-3-4
Shock
DC 1mA 通電状態にて、嵌合軸を含む互い
垂直な 6方向 490m/s2 {50G} の衝撃を
3 加える。
(JIS C60068-2-27 / MIL-STD-202試験法 213)
Mate applicable FPC and subject to the
following shock conditions. 3 times of shocks
shall be applied for each 6 directions along
3 mutually perpendicular axes, passing DC
1mA
current during the test.
(Total of 18 shocks)
Test pulse : Half Sine
Peak value : 490m/s2 {50G}
(JIS C60068-2-27 / MIL-STD-202Method 213)
Appearance
異状なきこと
No Damage
接触抵抗
Contact
Resistance
60 milliohm
MAX.
Discontinuity
1 microsecond
MAX.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
4 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
Item
Test Condition
Requirement
4-3-5
Heat
Resistance
適合FFCハーネスを嵌合させ85±2
雰囲気中に96時間 放置後取り出し、12時間
室温に放置する
(JIS C60068-2-2/MIL-STD-202 試験法 108)
Mate applicable FPC and expose to 85+2/-2
degrees C for 96 hours. Upon completion of the
exposure period, the test specimens shall be
conditioned at ambient room conditions for 1 to 2
hours, after which the specified measurements
shall be performed.
( JIS C60068-2-2/MIL-STD-202 Method 108 )
Appearance
異状なきこと
No Damage
接触抵抗
Contact
Resistance
60 milliohm MAX.
4-3-6
Cold
Resistance
適合FFCハーネスを嵌合させ-40±3
雰囲気中に96時間 放置後取り出し、12時間
室温に放置する
( JIS C60068-2-1 )
Mate applicable FPC and expose to -40+2/-2
degrees C for 96 hours. Upon completion of the
exposure period, the test specimens shall be
conditioned at ambient room conditions for 1 to
2 hours, after which the specified
measurements shall be performed.
( JIS C60068-2-1 )
Appearance
異状なきこと
No Damage
接触抵抗
Contact
Resistance
60 milliohm MAX.
4-3-7
湿
Humidity
適合FFCハーネスを嵌合させ60±2 相対
湿度 9095% の雰囲気中に 96時間 放置後
取り出し、12時間 室温に放置する。
( JIS C60068-2-78/MIL-STD-202 試験法 103 )
Mate applicable FPC and expose to 60+2/-2
degrees C,relative humidity 90 to 95% for 96
hours. Upon completion of the exposure period,
the test specimens shall be conditioned at
ambient room conditions for 1 to 2 hours, after
which the specified measurements shall be
performed.
( JIS C60068-2-78/MIL-STD-202 Method 103 )
Appearance
異状なきこと
No Damage
接触抵抗
Contact
Resistance
60 milliohm MAX.
Dielectric
Strength
4-1-3項満足のこと
Must meet 4-1-3
絶縁抵抗
Insulation
Resistance
20 Megohm MIN.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
5 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
Item
Test Condition
Requirement
4-3-8
温度サイクル
Temperature
Cycling
適合FFC-55±3℃に30
分、+85±2 30分、これを 1サイクル
し、5サイクル 繰り返す
但し、温度移行時間は 5分以内 とする
試験後 12時間 室温に放置する。
(JIS C60068-2-14)
Mate applicable FPC and subject to the
following conditions for 5 cycles. Upon
completion of the exposure period, the test
specimens shall be conditioned at ambient
room conditions for 1 to 2 hours, after which
the specified measurements shall be
performed.
(JIS C60068-2-14)
1 cycle
a) 55+3/-3 degrees C 30 minutes
b) +85+2/-2 degrees C 30 minutes
(Transit time shall be within 3 minutes)
Appearance
異状なきこと
No Damage
接触抵抗
Contact
Resistance
60 milliohm MAX.
4-3-9
亜硫酸ガス
SO2 Gas
適合FFCハーネスを嵌合させ40±2 にて
50±5ppmの亜硫酸ガス中に 24時間放置する。
Mate applicable FPC and expose them to the
following SO2 gas atmosphere.
Temperature 40+2/-2 degrees C
Gas Density 50+5/-5 ppm
Duration 24 hours
接触抵抗
Contact
Resistance
60 milliohm MAX.
4-3-10
半田付け性
Solder Ability
端子先端より 0.2mm、金具先端より 0.2mm
の位置まで、350±3 の半田に 5 浸す。
Dip solder tails and fitting nail into the molten
solder(held at 350+3/-3 degrees C)up to
0.2mm from the tip of the solder tails and
fitting nails for 5 seconds.
Solder
Wetting
浸漬面積の
75%以上
75% of immersed
area must show
no voids, pin
holes.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
6 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
Item
Test Condition
Requirement
4-3-11
半田耐熱性
Resistance to
Soldering Heat
赤外線リフロー
(Reflow by Infrared Reflow Machine)
第7項の推奨温度プロファイル条件にてリ
ローを行う。
Using the reflow profile condition below
Paragraph.
Appearance
端子ガタ、
割れ等
異状無き事
No Damage
手半田時 (Reflow by Manual Soldering iron)
子先端、及び金具先端より0.3mmの位置まで、
350±10℃の半田ゴテにて3加熱する。但し、
異常な加圧のないこと。
Using a soldering iron (350+10/-10 degrees C
for 3 seconds) heat up the area 0.3mm from
the tip of the solder tails and fitting nails.
However, do not apply excessive pressure to
either the terminals or fitting nails.
( ) 参考規格 Reference Standard
{ } 参考単位 Reference Unit
*各項目の評価サンプルは、製品図面に記載されている推奨基板レイアウト、推奨メタルマスクにて実装し
います。リフロー条件は4-3-13の推奨温度プロファイルにて実装しております。半田ペーストは、無鉛半田
Sn-3Ag-0.5Cu)を使用しています。
The evaluation samples of each specification test are reflowed according to the recommended Print Circuit
Board layout and the recommended metal mask thickness specified in the sales drawing. The reflow
conditions followed are specified in the reflow profile in section 4-3-13. Lead free solder (Sn-3Ag-0.5Cu) was
used as the soldering paste.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
7 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
【5.外観形状、寸法及び材 PRODUCT SHAPE, DIMENSIONS AND MATERIALS
図面参照 Refer to the drawing.
【6.挿入・抜去力 INSERTION FORCE/WITHDRAWAL FORCE
下記に示した表は、0.3mm厚のFPCを使用したときのFPC抜力のデータを示しております。ただし
FPCの仕様がFPC挿抜力に影響を与えるため、下記に示したFPC挿抜力の仕様を満たさない場合があります。
注意:以下表中の数値は参考値です
Table shown below is a data of FPC insertion/withdrawal force when using a thickness of 0.3mm FPC.
But, there's a case which FPC insertion/withdrawal force doesn't fulfill the data shown below,
because FPC specification affects the result of FPC insertion/withdrawal force .
NoticeThis chart shows reference value.
極数
No.
of
CKT
単位
UNIT
挿入力
Insertion Force
抜去力
Withdrawal Force
平均値
AVG.
最大値
MAX.
最小値
MIN.
平均値
AVG.
最大値
MAX.
最小値
MIN.
40
初回
1st
N
{kgf}
20.41
{2.08}
21.9
{2.23}
18.1
{1.85}
13.12
{1.34}
13.9
{1.42}
11.4
{1.16}
10回目
10th
N
{kgf}
13.84
{1.41}
15.9
{1.62}
11.6
{1.18}
10.64
{1.09}
10.9
{1.11}
10.2
{1.04}
20回目
20th
N
{kgf}
12.40
{1.27}
15.5
{1.58}
11.1
{1.13}
9.94
{1.01}
10.6
{1.08}
9.2
{0.94}
50
初回
1st
N
{kgf}
21.50
{2.19}
22.9
{2.34}
19.6
{2.00}
16.42
{1.68}
17.1
{1.74}
15.4
{1.57}
10回目
10th
N
{kgf}
15.62
{1.59}
16.4
{1.67}
14.8
{1.51}
11.64
{1.19}
13.5
{1.38}
10.9
{1.11}
20回目
20th
N
{kgf}
15.12
{1.54}
15.8
{1.61}
14.7
{1.50}
11.00
{1.12}
12.6
{1.29}
10.3
{1.05}
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
8 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
【7.赤外線リフロー条件 INFRARED REFLOW CONDITION
250℃以下(ピーク温度)
250 MAX. (PEAK TEMP.)
40(230℃以上)
40sec.(230 MIN.)
90±30
90±30 sec.
(予熱:150180℃以下)
(Pre-heat150180MAX.)
温度条件グラフ
TEMPERATURE CONDITION GRAPH
半田接合部の基板表面にて測
(Temperature is measured at the soldering area on the surface of the print circuit board)
注記:本リフロー条件に関しては、温度プロファイル、半田ペースト、大気、N2リフロー、基板などによ
り条件が異なりますので事前に実装評価(リフロー評価) を必ず実施願います。実装条件によっては、
製品性能に影響を及ぼす場合があります。
NOTE: Please investigate the mounting condition (reflow soldering condition) on your own devices
beforehand. The mounting conditions may change due to the soldering temperature, soldering
paste, air reflow machine, Nitrogen reflow machine, and the type of printed circuit board.
The different mounting conditions may have an influence on the product’s performance.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
9 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
【8.取り扱い説明書 INSTRUCTION FOR THE HANDLING OF THE CONNECTOR
8-1.各部の名称 DESCRIPTION OF EACH PART
8-2.基板への実装に関して MOUNTING ON THE PC BOARD
基板への実装は実装機にて実施願いますもし、手半田する場合は、TERMINAL及びNAIL等
触れない様に願います。(半田付け不良等の原因となる可能性が有ります。)
The mounting of the PC board is handled by the mounter. If to manually solder, please be cautious to not
touch the Terminal and Fitting Nail.(It will create the possibility to cause solderbility failure.)
HOUSING
NAIL
FFC
JACKET COVER
TERMINA
ロック部
JACKET
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
10 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
8-3.コネクタ嵌合に関して MATING THE CONNECTOR
コネクタを嵌合する際は、JACKETとJACKET COVERの全体もしくは中央を掴んで
挿入を実施ください。
When mating the connector, hold the JACKET AND JACKET COVER together at either a whole or
the center portion of them to insert.
全体
WHOLE
中央
CENTER
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
11 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
以下のような嵌合は回復不可能な機能不全や製品破壊につながりますので実施しないで下さい。
The following method of mating will cause either irreversable functionality failure or product
breaking, so please do not mate this way.
・FFCのみを掴まないでください。
Please do not hold the FFC part only
・JACKETとJACKET COVER 端部のみを掴まないでください。
Please do not hold the JACKET AND edge of the JACKET COVER only
FFCの浮き発生
WARPED FFC
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
12 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
・FFCを折り曲げるように掴まないでください。
Please do not hold the FFC like bending it.
FFCの浮き発生
WARPED FFC
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
13 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
FFCが極端に浮くと、嵌合時にHOUSINGと干渉し座屈する可能性があります。
If FFC warps too much, it will touch with the Header housing when mated,
andmay possibly cause buckling.
・JACKETとJACKET COVERの片端のみを掴まないでください。
斜め嵌合となり、不良につながります。
Please do not hold one side of the JACKET and the JACKET COVER only as shown below.
It will be mated in the slant direction and will cause failure
FFCの極端な浮き
TO WARPED FFC
干渉
TOUCH
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
14 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
・斜め嵌合は不良につながりますので実施しないでください。
Mating inconsistently will cause failure, so please do not do this.
・嵌合状態 及び 嵌合時のFFC引き回し作業においてロック部に無理な負荷が掛かるような
使用は避けてください。コネクタ破壊やはんだクラックを引き起こします。
Please be cautious not to put excess load at the lock part after mating and when FFC is pulled and
extracted. It may cause damage to the connector and may crack the soldering.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
15 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
コネクタの嵌合を取り外す際は、必ずロック解除して実施ください。万が一、ロックを解除していない状態でFFC
を抜いた時は、コンタクト部に付着物が無いか確認の上、再装着願います。
Please be sure to release the lock when unmating the connector. If the FFC is withdrawn without the lock has
not been released, please check to make sure that there is no debris on the contact area before inserting the
FPC again.
8-4.ご使用FFCに関して
FFCに規定された定格温度がFFC単体前提の場合が御座います
この時、コネクタと組み合わせての実使用において、FFC体の接着層が劣化する等の信頼性を満足できない
ケースを回避する為、実機での評価/確認をお願い致します。
There is a possibility that the prescript temperature of FFC is set to single it.
When actually using it with connector, Please do the evaluation and the confirmation with an actual equipment
to evade the case where reliability cannot be filled (the adhesive line of FFC is deteriorated etc)
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
16 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
9.注意事項 NOTES
9-1外観について
9-1-1
本製品の樹脂部に黒点、ウエルド部の線、多少の傷が確認される事がありますが、製品性能には
影響ございません。
Although this product may have a small black mark, a weld line or a scratch on the housing, these will not have
any influence on the products performance.
9-1-2
成形品の色相に多少の違いを生じる場合がありますが、製品性能には影響ありません。
There may be slight differences in the housing coloring, but there will be no influence on the products performance.
9-1-3
紫外線により変色する場合がありますが、製品性能に影響ありません
Although the ultraviolet light may potentially change the color, this change has no on the products performance.
9-2実装について
9-2-1
実装性能(平坦度)は、実装基板の反りの影響を含まないものと致します。
基板の反りはコネクタ両端部を基準とし、コネクタ中央部にて Max0.02mmとして下さい。
The mounting specification for coplanarity does not include the influence of warpage of the printed circuit board.
The warpage of the printed circuit board should be a maximum of 0.02mm if measuring from one connector edge
to the other.
9-2-2
本製品の一般性能確認はリジット基板にて実施おります。
フレキシブル基板等の特殊な基板へ実装する場合は、事前に実装確認等を行った上でご使用願います。
The product performance was tested using rigid printed circuit board.
In case the product needs to be reflowed onto flexible circuit board, please conduct a reflow test on the
flexible circuit board in advance.
9-2-3
フレキシブル基板に実装する場合は、基板の変形を防止するため、補強板をご使用願います。
Please add a stiffener on the flexible printed circuit (FFC) when you mount the connector onto FFC in order to
prevent deformation of the FFC.
9-2-4
リフロー条件によっては、樹脂部の変色や端子めっき部にヨリが発生する場合がありますが、製品性能に影響は
ございません。
Depending on the reflow conditions, there may be the possibility of a color change in the housing.
However, this color change does not have any effect on the products performance.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
17 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
9-2-5
リフロー後、半田付け部に変色が見られることがありますが、製品性能に影響はありません。
Although there might be some discoloration seen on the soldering tail after reflow, this will not influence
the products performance.
9-2-6
半田実装部の未半田は、ターミナル脱落、ピン間ショート、ターミナル座屈、またコネクタの基板からの外れが
懸念されます。従って全てのターミナルテール部及び、ネイル部に半田付けを行って下さい。
If you leave any soldering area on this product open, there may be the possibility of a missing terminal short
circuiting between pins, terminal buckling or the potential for the connector to come off of the printed circuit board.
Therefore, please solder all of the terminals and fitting nails on the printed circuit board.
9-2-7
実装機によってコネクタに負荷が加わると変形、破損する場合がありますので事前にご確認下さい。
If there is accidental contact with the connector while it is going through the reflow machine, there may be
deformation or damage caused to the connector. Please check to prevent this.
9-3製品の仕様について
9-3-1
コネクタの性能を損なう恐れがある為、コネクタの洗浄は、行わないで下さい。
Please do not conduct any washing process on the connector because it may damage the products function.
9-3-2
適合するFFCの導体部は、錫系めっき(ニッケル下地)品を使用願います。
Please make sure to use the appropriate FFC which has Tin plating (Nickel under plating) on the contact area.
9-3-3
量産前にご使用になるFFCとの相性確認を行った上で、ご使用をお願い致します。
Please check the compatibility between the connector and the FFC prior to moving to mass production.
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
18 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
9-3-4
コネクタにFFCを装着した状態で、FFCに過度の負荷が加わらないようにご注意頂き、御社基板のスペース上
コネクタに負担の掛かる位置への取り付けはしないで下さい。
コネクタのロックが解除されたり、FFCの抜け、断線、破損や接触不良の原因になります。
特に、連続的に加わる場合はFFCを固定するようにして下さい。
また、基板に対して垂直上下方向の引張荷重、コンタクトピッチ方向のこじり荷重を与えない様にご注意願います。
Please pay special attention not to have any pulling force/tension on the FFC when it is inserted into the connector.
This can cause; the actuator to be unlocked, the actuator to come off, cut the traces on the FFC,
and/or damage the FFC.
Please be especially careful to avoid placing the FFC in a location where it will have a constant force applied
on the FFC, If necessary, please fix the FFC directly on the chassis.
Also, please avoid pulling the FFC vertically or twisting the FFC back and force horizontally while it is inserted
in the connector.
9-3-5
本製品をご使用時に取り付けられた電線・プリント基板の共振や、機器の回転構造や可動部分の動作により
コネクタ嵌合部(接点部)が常に動いてしまう状態での御使用は避けて下さい。
接触部の摺動磨耗等による 接触不良の原因となります
従って、機器内で電線・プリント基板を固定し、共振を抑える等の処置をお願い致します。
Please do not use the connector in a condition where the wire, the printed circuit board, or the contact area is
experiencing a sympathetic vibration of wires and printed circuit board, and constant movement of devices.
This may cause a defect in the contact due to the contact area being worn down.
Therefore, please fix wires and printed circuit board on the chassis, and reduces sympathetic vibration.
9-3-6
活電状態の電気回路で、挿入、抜去ができることを前提に作られていません。スパーク等による危険の発生、性能
不良につながりますので、活電状態での挿入、抜去はしないで下さい
This product is not designed for the mating and unmating of the connectors to be performed under the condition of
an active electrical circuit. It may cause a spark and product defect if the connectors are mated and unmated in this
way.
NG
NG
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
19 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
9-3-7
本製品の端子は錫メッキを使用しております。ご使用になFFCとの相性確認としてウィスカー評価の実施を推奨いたしま
す。
The terminals for this product are tin plated. We recommend that a Tin whiskering test is performed between your
FFC and the connector beforehand to ensure that they are compatible.
9-3-8
コネクタに外力が加わらないようにクリアランスをあけた筐体構造にして下さい
Please keep enough clearance between connector and chassis of your application in order not to apply pressure
on the connector.
9-3-9
基板実装後に基板を直接積み重ねない様に注意してください。
Please do not stack the printed circuit board directly after mounted the connector on it.
9-4リペアについて
9-4-1
実装後において半田ごてによる手修正を行う際は、必ず仕様書掲載の条件以内で行って下さい。
条件を超えて実施した場合、端子の抜け、点ギャップの変化モールドの変形、溶融等、破損の原因になります。
When conducting manual repairs using a soldering iron, please follow the soldering conditions shown in the
product specification.
If the conditions in the product spec are not followed, it may cause the terminals to fall off, a change in the
contact gap, a deformation of the housing, melting of the housing, and damage the connector.
9-4-2
半田ゴテによる手修正を行なう際、過度の半田やフラックスを使用しないで下さい
半田上がりやフラックス上がりにより接触、機能不良に至る場合があります。
When conducting manual repairs using a soldering iron, please do not use more solder and flux than needed.
This may cause solder wicking and flux wicking issues, and it will eventually cause a contact defect
and functional issues.
10.環境指令への適合 COMPLIANCE WITH ENVIRONMENTAL DIRECTIVE
ELV及びRoHS適合品
ELV and RoHS Compliant
LANGUAGE
JAPANESE
ENGLISH
REVISE ON PC ONLY
TITLE: 0.5mmPITCH FFC TO BOARD CONNECTOR
製品仕様書
C
SEE SHEET 1 OF 20
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO
MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
REV.
DESCRIPTION
DOCUMENT NUMBER
PS-501864-002
FILE NAME
PS501864002.docx
SHEET
20 OF 20
EN-037(2013-04 rev.1)
PRODUCT SPECIFICATION
REV.
REV. RECORD
DATE
EC NO.
WRTTN:
CH'K:
A
RELEASED
06/03/17
J2006-2959
H.IIJIMA
K.TAKAHASHI
B
REVISED
13/01/10
J2013-0749
A.ISHII
K.TAKAHASHI
C
REVISED
15/06/08
J2015-1609
A.ISHII
K.TAKAHASHI