MCC TM Micro Commercial Components omponents 20736 Marilla Street Chatsworth !"# $ % !"# Features * Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates Compliant. See ordering information) * * * * * Glass Passivated Junction Excellent Clamping Capability Built-in Strain Relief Low Inductance Halogen free available upon request by adding suffix "-HF" Mechanical Data * * SMA2EZ5.1D5 THRU SMA2EZ75D5 2 W Glass Passivated Junction Silicon Zener Diode 5.1-75 Volts DO-214AC (SMA) (LEAD FRAME) Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 TERMINALS : Solder plated, solderable per MIL-STD-750, method 2026 POLARITY : Color band denotes positive end (cathode) H J Maximum Ratings @ 25oC Unless Otherwise Specified Peak Pulse Power Dissipation (Note 2) o Derate above 75 C Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) (Note 3) Operating And Storage Temperature Range PD 2 24 Watts mW/ oC A E C D B F IFSM 15 G Amps DIMENSIONS TJ , TSTG DIM A B C D E F G H J o -55 C to +150o C NOTES: 1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7. 2. Mounted on 5.0mm2(.013mm thick) land areas. INCHES MIN .079 .050 .002 --.030 .065 .189 .157 .090 MM MIN 2.00 1.27 .05 --.76 1.65 4.80 4.00 2.25 MAX .096 .064 .008 .02 .060 .091 .220 .181 .115 MAX 2.44 1.63 .20 .51 1.52 2.32 5.59 4.60 2.92 NOTE SUGGESTED SOLDER PAD LAYOUT 0.090 " 3. Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum. 0.085 " 0.070" Revision: C www.mccsemi.com 1 of 5 2013/04/26 MCC TM Micro Commercial Components SMA2EZ5.1D5 THRU SMA2EZ75D5 O ELECTRICAL CHARACTERISTICS(TA=25 C unless otherwise noted)VF=1.5V max,IF=200mA for all types. Nominal Zener Test Maximum Zener Impedance (Note 3) Leakage Current Type No. Voltage Vz @I ZT Current ZZT @ IZT IZT (Note 1.) Volts SMA2EZ5.1D5 IZK IR VR mA uA Max Volts (Note 2.) 5.1 mA Ohms Ohms 98.0 3.5 600 1 5 1 356 3.5 5.6 6.2 6.8 7.5 8.2 9.1 10 11 12 13 14 15 16 17 18 19 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 89.5 80.5 73.5 66.5 61 55 50 45.5 41.5 38.5 35.7 33.4 31.2 29.4 27.8 26.3 25 22.8 20.8 18.5 16.6 15.1 13.9 12.8 11.6 10.6 9.8 9 8.1 7.4 6.7 2.5 500 1 5 2 1.5 700 1 5 3 2 700 1 5 4 324 292 266 242 220 200 182 166 152 138 130 122 114 107 100 95 90 82 76 68 60 55 50 47 43 39 36 32 29 27 24 3.3 3.1 2.9 2.66 2.44 2.2 2.0 1.82 1.66 1.54 1.43 1.33 1.25 1.18 1.11 1.05 1 0.91 0.83 0.74 0.67 0.61 0.56 0.51 0.45 0.42 0.39 0.36 0.32 0.29 0.27 SMA2EZ5.6D5 SMA2EZ6.2D5 SMA2EZ6.8D5 SMA2EZ7.5D5 SMA2EZ8.2D5 SMA2EZ9.1D5 SMA2EZ10D5 SMA2EZ11D5 SMA2EZ12D5 SMA2EZ13D5 SMA2EZ14D5 SMA2EZ15D5 SMA2EZ16D5 SMA2EZ17D5 SMA2EZ18D5 SMA2EZ19D5 SMA2EZ20D5 SMA2EZ22D5 SMA2EZ24D5 SMA2EZ27D5 SMA2EZ30D5 SMA2EZ33D5 SMA2EZ36D5 SMA2EZ39D5 SMA2EZ43D5 SMA2EZ47D5 SMA2EZ51D5 SMA2EZ56D5 SMA2EZ62D5 SMA2EZ68D5 SMA2EZ75D5 Notes: ZZK @ IZK Maximum Surge Current Zener Current @TA=25 I ZM I ZSM-A mA (Note 4.) 2 700 0.5 5 5 2.3 700 0.5 5 6 2.5 700 0.5 3 7 3.5 700 0.25 3 7.6 4 4.5 5 5.5 7 8 9 10 11 11 12 13 18 20 23 25 30 35 40 48 55 60 75 90 700 700 700 700 700 700 750 750 750 750 750 750 750 1000 1000 1000 1000 1500 1500 1500 2000 2000 2000 2000 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 1 1 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 8.4 9.1 9.9 10.6 11.4 12.2 13 13.7 14.4 15.2 16.7 18.2 20.6 22.5 25.1 27.4 29.7 32.7 35.8 38.8 42.6 47.1 51.7 56 Device Marking 2E5.1/2C5V1 2E5.6/2C5V6 2E6.2/2C6V2 2E6.8/2C6V8 2E7.5/2C7V5 2E8.2/2C8V2 2E9.1/2C9V1 2E10/2C10 2E11/2C11 2E12/2C12 2E13/2C13 2E14/2C14 2E15/2C15 2E16/2C16 2E17/2C17 2E18/2C18 2E19/2C19 2E20/2C20 2E22/2C22 2E24/2C24 2E27/2C27 2E30/2C30 2E33/2C33 2E36/2C36 2E39/2C39 2E43/2C43 2E47/2C47 2E51/2C51 2E56/2C56 2E62/2C62 2E68/2C68 2E75/2C75 1. TOLERANCES - Suffix indicates 5% tolerance any other tolerance will be considered as a special device. 2. ZENER VOLTAGE (Vz) MEASUREMENT - guarantees the zener voltage when measured at 40 ms from the diode body, and an ambient temperature of 25 centigrade degrees. 3.ZENER IMPEDANCE (Zz) DERIVATION - The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms falue equal to 10% of the dc zener current (I ZT or IZK) is superimposed on IZT or IZK . NON-REPETITIVE - The rating listed in the electrical characteristics table 4. SURGE CURRENT (Izsm) is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test current, IZT, per JEDEC standards, however, actual device capability is as described in Figure 3. Revision: C www.mccsemi.com 2 of 5 2013/04/26 MCC RATING AND CHARACTERISTICS CURVES TM SMA2EZ5.1 D5 THRU SMA2EZ75D5 Micro Commercial Components JL (t,D) TRANSIENT THERMAL RESISTANCE JUNCTION-TO-LEAD(/W) 30 D = 0.5 20 10 0.2 7 5 0.1 3 2 0.05 1 0.02 0.7 0.5 0.01 0.3 0.0001 NOTE BELOW 0.1 SECOND, THERMAL RESPONSE CURVE IS APPLICABLE TO ANY LEAD LENGTH (L) D=0 0.0002 0.0005 0.001 0.002 0.005 0.01 0.02 0.05 SINGLE PULSE TJL = JL(t)PPK REPETITIVE PULSES TJL = JL(t,D)PPK 0.1 0.2 0.5 1 2 5 10 Fig. 2-TYPICAL THERMAL RESPONSE PPK, PEAK SURGE POWER(WATTS) 500 150 IR, REVERSE LEADAGE(uAdc) @VR AS SPECIFIED IN ELEC. CHAR. TABLE 250 RECTANGULAR NONREPETITIVE WAVEFORM TJ = 25 PRIOR TO INITIAL PULSE 100 50 30 20 10 .1 .2 .3 5 1 2 3 5 10 20 50 100 0.005 0.003 0.002 0.001 0.0005 0.0003 0.0002 0.0001 1 2 5 10 20 50 100 200 500 1K P.W. PULSE WIDTH (ms) NOMINAL VZ (VOLTS) Fig. 3-MAXIMUM SURGE POWER Fig. 4-TYPICAL REVERSE LEAKAGE 8 200 6 VZ, TEMPERATURE C OEFFICIENT(mV) @ IZT VZ, TEMPERATURE COEFFICIENT(mV/) @ IZT 0.1 0.05 0.03 0.02 0.01 4 2 0 RANGE -2 -4 3 4 6 8 10 12 VZ, ZENER VOLTAGE @IZT (VOLTS) 100 RANGE 50 40 30 20 10 0 20 40 60 80 100 120 140 160 180 200 VZ, ZENER VOLTAGE @IZT (VOLTS) Fig. 5-UNITS 3.9 TO 12 VOLTS Revision: C Fig. 6-UNITS 10 TO 200 VOLTS www.mccsemi.com 3 of 5 2013/04/26 MCC RATING AND CHARACTERISTICS CURVES SMA2EZ5.1 D5 THRU SMA2EZ75D5 Micro Commercial Components 100 IZ, ZENER CURRENT (mA) IZ, ZENER CURRENT (mA) 100 50 30 20 10 5 3 2 1 0.5 0.3 0.2 0.1 0 1 2 3 4 5 6 7 8 50 30 20 10 5 3 2 1 0.5 0.3 0.2 0.1 0 9 10 10 50 30 20 10 5 3 2 1 0.5 0.3 0.2 0.1 100 120 140 160 180 70 80 90 100 Fig. 8-VZ = 12 THRU 82 VOLTS JL, JUNCTION-LEAD THERMAL RESISTANCE (/W) Fig. 7-VZ = 3.9 THRU 10 VOLTS 100 20 30 40 50 60 VZ, ZENER VOLTAGE (VOLTS) VZ, ZENER VOLTAGE (VOLTS) IZ, ZENER CURRENT (mA) TM 80 70 60 PRIMARY PATH OF CONDUCTION IS THROUGH THE CATHODE LEAD 50 40 30 20 10 0 0 200 1/8 1/4 3/8 1/2 5/8 3/4 7/8 1 VZ, ZENER VOLTAGE (VOLTS) L, LEAD LENGTH TO HEAT SINK (INCH) Fig. 9-VZ = 100 THRU 200 VOLTS Fig. 10-TYPICAL THERMAL RESISTANCE Revision: C www.mccsemi.com 4 of 5 2013/04/26 MCC TM Micro Commercial Components Ordering Information : Device Packing Part Number-TP Tape&Reel: 7.5Kpcs/Reel Note : Adding "-HF" suffix for halogen free, eg. Part Number-TP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. www.mccsemi.com Revision: C 5 of 5 2013/04/26