Data Sheet, Rev. 0.5, Dec. 2003 HYS72D128300GBR-[5/6/7]-B HYS72D256320GBR-[5/6/7]-B HYS72D128500HR-[7F/7]-B HYS72D128321GBR-[5/6/7]-B 184-Pin Registered Double Data Rate SDRAM Module Reg DIMM DDR SDRAM Green Product Lead Containing Product Memory Products N e v e r s t o p t h i n k i n g . Edition 2003-12 Published by Infineon Technologies AG, St.-Martin-Strasse 53, 81669 Munchen, Germany (c) Infineon Technologies AG 2003. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Data Sheet, Rev. 0.5, Dec. 2003 HYS72D128300GBR-[5/6/7]-B HYS72D256320GBR-[5/6/7]-B HYS72D128500HR-[7F/7]-B HYS72D128321GBR-[5/6/7]-B 184-Pin Registered Double Data Rate SDRAM Module Reg DIMM Memory Products N e v e r s t o p t h i n k i n g . HYS72D128300GBR-[5/6/7]-B, HYS72D256320GBR-[5/6/7]-B, HYS72D128500HR-[7F/7]-B Revision History: Rev. 0.5 2003-12 Previous Version: Page Subjects (major changes since last revision) We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc.mp@infineon.com Template: mp_a4_v2.0_2003-06-06.fm HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module 1 1.1 1.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 3.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4 SPD Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6 Application Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Data Sheet 5 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Overview 1 Overview 1.1 Features * * * * * * * * * * * * 184-pin Registered 8-Byte Dual-In-Line DDR SDRAM Module for "1U" PC, Workstation and Server main memory applications One rank 128M x 72 organization and two rank 256M x 72 organization JEDEC standard Double Data Rate Synchronous DRAMs (DDR SDRAM) with a single + 2.5 V ( 0.2 V) power supply and +2.6( 0.1 V) power supply for DDR400 Built with DDR SDRAMs in 66-Lead TSOPII and FBGA 60 package Programmable CAS Latency, Burst Length, and Wrap Sequence (Sequential & Interleave) Auto Refresh (CBR) and Self Refresh All inputs and outputs SSTL_2 compatible Re-drive for all input signals using register and PLL devices. Serial Presence Detect with E2PROM Low Profile Modules form factor: 133.35 mm x 28.58 mm (1.1") x 4.00 mm and 133.35 mm x 30.48 mm (1.2") x 4.00 mm Based on Jedec standard reference card layout RawCard "B", "C" and "D" Gold plated contacts Table 1 Performance Part Number Speed Code -5 -6 -7 -7F Unit Speed Grade Component DDR400B DDR333B DDR266A DDR266 -- Module PC3200-3033 PC2700-2533 PC2100-2033 PC2100-2022 -- fCK3 200 @ CL = 2.5 fCK2.5 166 @ CL = 2 fCK2 133 max. Clock Frequency @ CL = 3 1.2 166 -- -- MHz 166 143 143 MHz 133 133 133 MHz Description The HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B are low profile versions of the standard Registered DIMM modules with 1.1" inch (28.58) and 1.2" inch (30,40 mm) height for 1U Server Applications. The Low Profile DIMM versions are available as 128M x 72 (1 GB) and 256M x 72 (2 GB). The memory array is designed with Double Data Rate Synchronous DRAMs for ECC applications. All control and address signals are re-driven on the DIMM using register devices and a PLL for the clock distribution. This reduces capacitive loading to the system bus, but adds one cycle to the SDRAM timing. A variety of decoupling capacitors are mounted on the PC board. The DIMMs feature serial presence detect based on a serial E2PROM device using the 2-pin I2C protocol. The first 128 bytes are programmed with configuration data and the second 128 bytes are available to the customer. Data Sheet 6 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Overview Table 2 Ordering Information1)2) Compliance Code2) Description HYS72D128300GBR-5-B PC3200R-30331-C0 one rank 1 GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128321GBR-5-B PC3200R-30331-B0 two ranks 1 GByte Reg. ECC DIMM 512 MBit (x8) HYS72D256320GBR-5-B PC3200R-30331-D0 two ranks 2 GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128300GBR-6-B PC2700R-25330-C0 one rank 1 GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128321GBR-6-B PC2700R-25330-B0 two ranks 1 GByte Reg. ECC DIMM 512 MBit (x8) HYS72D256320GBR-6-B PC2700R-25330-D0 two ranks 2 GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128300GBR-7-B PC2100R-20330-C0 one rank 1 GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128321GBR-7-B PC2100R-20330-B0 two ranks1 GByte Reg. ECC DIMM 512 MBit (x8) HYS72D256320GBR-7-B PC2100R-20330-D0 two ranks 2 GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128500HR-7F-B PC2100R-20220-M one rank 1GByte Reg. ECC DIMM 512 MBit (x4) HYS72D128500HR-7-B PC2100R-20330-M one rank 1GByte Reg. ECC DIMM 512 MBit (x4) Type SDRAM Technology PC3200 (CL=3) PC2700 (CL=2.5) PC2100 (CL=2) 1) All part numbers end with a place code (not shown), designating the silicon-die revision. Reference information available on request. Example: HYS72D128300GBR-[5/6/7]-B, indicating Rev.B die are used for SDRAM components. 2) The Compliance Code is printed on the module labels and describes the speed sort for example "PC2100R", the latencies (for example "20330" means CAS latency = 2.5, tRCD latency = 3 and tRP latency =3 ) and the Raw Card used for this module Data Sheet 7 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Pin Configuration 2 Pin Configuration Table 3 Pin Definitions and Functions Symbol Type Function A0 - A11,A12 Address Inputs BA0, BA1 Bank Selects DQ0 - DQ63 Data Input/Output CB0 - CB7 Check Bits (x72 organization only) RAS,CAS,WE Command Inputs CKE0, CKE1 Clock Enable DQS0 - DQS8 SDRAM low data strobes CK0, CK0 Differential Clock Input DM0 - DM8 DQS9 - DQS17 SDRAM low data mask/ high data strobes S0 - S1 Chip Selects VDD VSS VDDQ VDDID VDDSPD VREF Power (+2.5 V) SCL Serial bus clock SDA Serial bus data line SA0 - SA2 slave address select NC no connect Ground I/O Driver power supply VDD Indentification flag EEPROM power supply I/O reference supply DU don't use RESET Reset pin (forces register inputs low)1) 1) for detailed description of the Power Up and Power Management on DDR Registered DIMMs see the Application Note at the end of this datasheet Data Sheet 8 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Pin Configuration Table 4 Pin Configuration1) PIN# Symbol PIN# Symbol PIN# Symbol PIN# Symbol 1 VREF 48 A0 94 DQ4 141 A10 2 DQ0 49 CB2 95 DQ5 142 CB6 3 VSS 50 VSS 96 VDDQ 143 VDDQ 4 DQ1 51 CB3 97 DQS9 144 CB7 5 DQS0 52 6 DQ2 7 VDD 8 BA1 98 DQ6 KEY 99 DQ7 145 KEY VSS 53 DQ32 100 VSS 146 DQ36 DQ3 54 VDDQ 101 NC 147 DQ37 9 NC 55 DQ33 102 NC 148 VDD 10 RESET 56 DQS4 103 NC 149 DM4/DQS13 11 VSS 57 DQ34 104 VDDQ 150 DQ38 12 DQ8 58 VSS 105 DQ12 151 DQ39 13 DQ9 59 BA0 106 DQ13 152 VSS 14 DQS1 60 DQ35 107 DQS10 153 DQ44 15 VDDQ 61 DQ40 108 VDD 154 RAS 16 DU 62 VDDQ 109 DQ14 155 DQ45 17 DU 63 WE 110 DQ15 156 VDDQ 18 VSS 64 DQ41 111 CKE1 157 S0 19 DQ10 65 CAS 112 VDDQ 158 S1 20 DQ11 66 VSS 113 NC 159 DQS14 21 CKE0 67 DQS5 114 DQ20 160 VSS 22 VDDQ 68 DQ42 115 NC / A12 161 DQ46 23 DQ16 69 DQ43 116 VSS 162 DQ47 24 DQ17 70 VDD 117 DQ21 163 NC 25 DQS2 71 NC 118 A11 164 VDDQ 26 VSS 72 DQ48 119 DQS11 165 DQ52 27 A9 73 DQ49 120 VDD 166 DQ53 28 DQ18 74 VSS 121 DQ22 167 NC 29 A7 75 DU 122 A8 168 VDD 30 VDDQ 76 DU 123 DQ23 169 DQS15 31 DQ19 77 VDDQ 124 VSS 170 DQ54 32 A5 78 DQS6 125 A6 171 DQ55 33 DQ24 79 DQ50 126 DQ28 172 VDDQ 34 VSS 80 DQ51 127 DQ29 173 NC 35 DQ25 81 128 VDDQ 174 DQ60 36 DQS3 82 VSS VDDID 129 DQS12 175 DQ61 37 A4 83 DQ56 130 A3 176 VSS 38 VDD 84 DQ57 131 DQ30 177 DQS16 39 DQ26 85 VDD 132 VSS 178 DQ62 40 DQ27 86 DQS7 133 DQ31 179 DQ63 41 A2 87 DQ58 134 CB4 180 VDDQ Data Sheet 9 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Pin Configuration Pin Configuration1) (cont'd) Table 4 PIN# Symbol PIN# Symbol PIN# Symbol PIN# Symbol 42 VSS 88 DQ59 135 CB5 181 SA0 43 A1 89 VSS 136 VDDQ 182 SA1 44 CB0 90 NC 137 CK0 183 SA2 45 CB1 91 SDA 138 CK0 184 VDDSPD 46 VDD 92 SCL 139 VSS - - 47 DQS8 93 VSS 140 DQS17 - - 1) A12 is used for 256Mbit and 512Mbit based modules only. Table 5 Address Format Density Organization Memory Ranks 1 GB 128M x 72 1 1 GB 128M x 72 2 GB 256M x 72 Data Sheet SDRAMs # of SDRAMs # of row/bank/ column bits Refresh Period Interval 128M x 4 18 13/2/12 8K 64 ms 7.8 s 2 64M x 8 18 13/2/11 8K 64 ms 7.8 s 2 128M x 4 36 13/2/12 8K 64 ms 7.8 s 10 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Pin Configuration VSS RS0 DQS0 DM0/DQS9 DQ0 DQ1 DQ2 DQ3 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DQ8 DQ9 DQ10 DQ11 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DQ16 DQ17 DQ18 DQ19 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQ24 DQ25 DQ26 DQ27 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQ32 DQ33 DQ34 DQ35 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DM DQ4 DQ5 DQ6 DQ7 D0 DQ12 DQ13 DQ14 DQ15 D1 S DM I/O 0 I/O 1 I/O 2 I/O 3 DM D10 DM2/DQS11 DM DQ20 DQ21 DQ22 DQ23 D2 DQS3 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DM D11 DM3/DQS12 S DM DQ28 DQ29 DQ30 DQ31 D3 DQS4 DQS I/O 0 I/O 1 I/O 2 I/O 3 DM4/DQS13 S DQ36 DQ37 DQ38 DQ39 D4 DQ40 DQ41 DQ42 DQ43 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DQ48 DQ49 DQ50 DQ51 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DQ56 DQ57 DQ58 DQ59 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DM DQS6 DM6/DQS15 DM DQ52 DQ53 DQ54 DQ55 D6 DQS7 I/O 0 I/O 1 I/O 2 I/O 3 DM5/DQS14 DQ44 DQ45 DQ46 DQ47 D5 S DQS DM DQS5 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DM D12 S DM D13 S DM VDDSPD Serial PD VDDQ D0-D17 VDD D0-D17 VREF D0-D17 VSS D0-D17 VDDID Strap: see Note 4 D14 Serial PD DQS S I/O 0 I/O 1 D15 I/O 2 I/O 3 DM SCL SDA WP A0 A1 A2 SA0 SA1 SA2 DM7/DQS16 CB0 CB1 CB2 CB3 R E G I S T E R S0 BA0-BA1 A0-A136 RAS CAS CKE0 WE PCK PCK Data Sheet DQS DM DQS2 Figure 1 D9 S DM1/DQS10 DQS1 DQS8 DQS I/O 0 I/O 1 I/O 2 I/O 3 DM DQ60 DQ61 DQ62 DQ63 D7 D8 DM DM8/DQS17 CB4 CB5 CB6 CB7 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS I/O 0 I/O 1 I/O 2 I/O 3 S DM D16 S D17 DM Notes: 1. DQ-to-I/O wiring may be changed within a byte. 2. DQ/DQS/DM/CKE/S relationships must be maintained as shown. 3. DQ/DQS resistors should be 22 Ohms. 4. VDDID strap connections (for memory device VDD, VDDQ): STRAP OUT (OPEN): VDD = VDDQ STRAP IN (VSS): VDD VDDQ. 5. Address and control resistors should be 22 Ohms. 6. A13 is not wired for raw card B. RS0 -> CS : SDRAMs D0-D17 RBA0-RBA1 -> BA0-BA1: SDRAMs D0-D17 RA0-RA136 -> A0-A136: SDRAMs D0-D17 RRAS -> RAS: SDRAMs D0-D17 RCAS -> CAS: SDRAMs D0-D17 RCKE0A -> CKE: SDRAMs D0-D17 CK0, CK0 --------- PLL* RWE -> WE: SDRAMs D0-D17 * Wire per Clock Loading Table/Wiring Diagrams RESET Block Diagram: 1 Rank 128M x 72 DDR SDRAM DIMM HYS72D128[300/500]GBR-[5/6/7/7F]-B 11 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Pin Configuration RS1 RS0 DQS0 DM0/DQS9 DQS4 DM4/DQS13 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D0 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 D9 DQS1 DM1/DQS10 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D4 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D13 DQS5 DM5/DQS14 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D1 DQS2 DM2/DQS11 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D2 CS DQS DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 D10 CS CS DQS DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D5 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D14 DQS6 DM6/DQS15 DQS DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 D11 DQS3 DM3/DQS12 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D6 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D15 DQS7 DM7DQS16 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D3 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 D12 CS DQS DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 D7 DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS D16 DQS8 DM8/DQS17 CB0 CB1 CB2 CB3 CB4 CB5 CB6 CB7 S0 S1 BA0-BA1 A0-A137 RAS CAS CKE0 CKE1 WE R E G I S T E R PCK PCK Figure 2 Data Sheet DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS D8 DQS DM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 CS DQS VDDSPD D17 Serial PD SDA WP A0 A1 Serial PD D0-D17 D0-D17 VDDQ SCL A2 SA0 SA1 SA2 VDD VREF VSS VDDID D0-D17 D0-D17 Strap: see Note 4 CK0, CK0 --------- PLL* RS0 -> CS : SDRAMs D0-D8 * Wire per Clock Loading Table/Wiring Diagrams RS1 -> CS : SDRAMs D9-D17 Notes: RBA0-RBA1 -> BA0-BA1: SDRAMs D0-D17 1. DQ-to-I/O wiring may be changed within a byte. RA0-RA137 -> A0-A137: SDRAMs D0-D17 2. DQ/DQS/DM/CKE/S relationships must be maintained as shown. RRAS -> RAS: SDRAMs D0-D17 3. DQ/DQS resistors should be 22 Ohms. RCAS -> CAS: SDRAMs D0-D17 4. VDDID strap connections (for memory device VDD, VDDQ): RCKE0 -> CKE: SDRAMs D0-D8 STRAP OUT (OPEN): VDD = VDDQ RCKE1 -> CKE: SDRAMs D9-D17 STRAP IN (VSS): VDD VDDQ. RWE -> WE: SDRAMs D0-D17 5. RS0 and RS1 alternate between the back and front sides of the DIMM. 6. Address and control resistors should be 22 Ohms. RESET 7. A13 is not wired for raw card A. Block Diagram - 2 Ranks 64M x 72 DDR SDRAM HYS72D128321GBR-[5/6/7]-B 12 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Pin Configuration VSS RS1 RS0 DQS0 DM0/DQS9 DQ0 DQ1 DQ2 DQ3 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQ8 DQ9 DQ10 DQ11 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQ16 DQ17 DQ18 DQ19 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQ24 DQ25 DQ26 DQ27 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQ32 DQ33 DQ34 DQ35 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQ40 DQ41 DQ42 DQ43 CS DQ48 DQ49 DQ50 DQ51 DQS I/O 0 I/O 1 I/O 2 I/O 3 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQ56 DQ57 DQ58 DQ59 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS CB0 CB1 CB2 CB3 CS DM D0 DQS I/O 3 I/O 2 I/O 1 I/O 0 CS DM DQS I/O 0 I/O 1 I/O 2 I/O 3 DQ4 DQ5 DQ6 DQ7 D18 CS DM D9 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D27 DM1/DQS10 DQS1 CS DM D1 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM DQ12 DQ13 DQ14 DQ15 D19 DQS2 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D10 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D28 DM2/DQS11 DM D2 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM DQ20 DQ21 DQ22 DQ23 D20 DQS3 DQS I/O 0 I/O 1 I/O 2 I/O 3 D11 DQS I/O 0 I/O 1 I/O 2 I/O 3 D12 CS DM DQS I/O 0 I/O 1 I/O 2 I/O 3 D29 DQS I/O 0 I/O 1 I/O 2 I/O 3 D30 CS DM DM3/DQS12 DM D3 DM DQ28 DQ29 DQ30 DQ31 D21 DQS4 CS DM CS DM DM4/DQS13 DM D4 DQS DM DQ36 DQ37 DQ38 DQ39 D22 DQS5 DM D5 DM5/DQS14 DM DQS6 DM I/O 0 I/O 1 I/O 2 I/O 3 CS DQS I/O 0 I/O 1 I/O 2 I/O 3 D13 DQS DQ44 DQ45 DQ46 DQ47 D23 CS I/O 0 I/O 1 I/O 2 I/O 3 DM DQS I/O 0 I/O 1 I/O 2 I/O 3 D14 CS DM D31 CS DM D32 DM6/DQS15 DM D6 DM DQ52 DQ53 DQ54 DQ55 D24 DQS7 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D15 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D33 DM7/DQS16 DM D7 DM DQ60 DQ61 DQ62 DQ63 D25 DQS8 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D16 DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D34 DM8/DQS17 D8 DM DM DQS I/O 0 I/O 1 I/O 2 I/O 3 CB4 CB5 CB6 CB7 D26 CK0, CK0 --------- PLL* * Wire per Clock Loading Table/Wiring Diagrams R E G I S T E R WE PCK PCK Figure 3 Data Sheet RSO -> CS : SDRAMs D0-D17 RS1 -> CS: SDRAMs D18-D35 RBA0-RBA1 -> BA0-BA1: SDRAMs D0-D35 RA0-RA13 -> A0-A13: SDRAMs D0- D35 RRAS -> RAS: SDRAMs D0-D35 RCAS -> CAS: SDRAMs D0-D35 RCKE0 -> CKE: SDRAMs D0-D17 RCKE1 -> CKE: SDRAMs D18-D35 RWE -> WE: SDRAMs D0-D35 RESET WP A0 A1 D17 VDDSPD Serial PD SCL S0 S1 BA0-BA1 A0-A13 RAS CAS CKE0 CKE1 CS A2 SA0 SA1 SA2 VDDQ SDA VDD VREF VSS VDDID DM DQS I/O 0 I/O 1 I/O 2 I/O 3 CS DM D35 Serial PD D0-D35 D0-D35 D0-D35 D0-D35 Strap: see Note 4 Notes: 1. DQ-to-I/O wiring may be changed within a byte. 2. DQ/DQS/DM/CKE/S relationships must be maintained as shown. 3. DQ/DQS resistors should be 22 Ohms. 4. VDDID strap connections (for memory device VDD, VDDQ): STRAP OUT (OPEN): VDD = VDDQ STRAP IN (VSS): VDD VDDQ. 5. Address and control resistors should be 22 Ohms. 6. Each Chip Select and CKE pair alternate between decks for thermal enhancement. Block Diagram - 2 Ranks 128M x 72 DDR SDRAM HYS72D256320GBR-[5/6/7]-B 13 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics 3 Electrical Characteristics 3.1 Operating Conditions Table 6 Absolute Maximum Ratings Parameter Symbol Voltage on I/O pins relative to VSS VIN, VOUT Values min. typ. max. Unit Note/ Test Condition -0.5 - VDDQ + V - 0.5 Voltage on inputs relative to VSS Voltage on VDD supply relative to VSS Voltage on VDDQ supply relative to VSS Operating temperature (ambient) Storage temperature (plastic) Power dissipation (per SDRAM component) Short circuit output current VIN VDD VDDQ TA TSTG PD IOUT -1 - +3.6 V - -1 - +3.6 V - -1 - +3.6 V - 0 - +70 C - -55 - +150 C - - 1 - W - - 50 - mA - Attention: Permanent damage to the device may occur if "Absolute Maximum Ratings" are exceeded. This is a stress rating only, and functional operation should be restricted to recommended operation conditions. Exposure to absolute maximum rating conditions for extended periods of time may affect device reliability and exceeding only one of the values may cause irreversible damage to the integrated circuit. Table 7 Electrical Characteristics and DC Operating Conditions Parameter Symbol VDD Device Supply Voltage VDD Output Supply Voltage VDDQ Output Supply Voltage VDDQ EEPROM supply voltage VDDSPD Supply Voltage, I/O Supply VSS, Voltage VSSQ Input Reference Voltage VREF I/O Termination Voltage VTT Device Supply Voltage Unit Note/Test Condition 1) Values Min. Typ. Max. 2.3 2.5 2.7 V 2.5 2.6 2.7 V 2.3 2.5 2.7 V 2.5 2.6 2.7 V fCK 166 MHz fCK > 166 MHz 2) fCK 166 MHz 3) fCK > 166 MHz 2)3) 2.3 2.5 3.6 V -- 0 V -- 0 0.49 x VDDQ 0.5 x VDDQ 0.51 x VDDQ V 4) VREF - 0.04 VREF + 0.04 V 5) Input High (Logic1) Voltage VIH(DC) VREF + 0.15 8) Input Low (Logic0) Voltage VIL(DC) -0.3 Input Voltage Level, CK and CK Inputs VIN(DC) -0.3 VDDQ + 0.3 V VREF - 0.15 V VDDQ + 0.3 V Input Differential Voltage, CK and CK Inputs VID(DC) 0.36 VDDQ + 0.6 V 8)6) VI-Matching Pull-up Current to Pull-down Current VIRatio 0.71 1.4 -- 7) (System) Data Sheet 14 8) 8) Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Table 7 Electrical Characteristics and DC Operating Conditions (cont'd) Parameter Symbol Unit Note/Test Condition 1) Values Min. Typ. Max. Input Leakage Current II -2 2 A Any input 0 V VIN VDD; All other pins not under test = 0 V 8)9) Output Leakage Current IOZ -5 5 A DQs are disabled; 0 V VOUT VDDQ Output High Current, Normal Strength Driver IOH -- -16.2 mA VOUT = 1.95 V Output Low Current, Normal Strength Driver IOL 16.2 -- mA VOUT = 0.35 V 1) 0 C TA 70 C 2) DDR400 conditions apply for all clock frequencies above 166 MHz 3) Under all conditions, VDDQ must be less than or equal to VDD. 4) Peak to peak AC noise on VREF may not exceed 2% VREF (DC). VREF is also expected to track noise variations in VDDQ. 5) VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track variations in the DC level of VREF. 6) VID is the magnitude of the difference between the input level on CK and the input level on CK. 7) The ratio of the pull-up current to the pull-down current is specified for the same temperature and voltage, over the entire temperature and voltage range, for device drain to source voltage from 0.25 to 1.0 V. For a given output, it represents the maximum difference between pull-up and pull-down drivers due to process variation. 8) Inputs are not recognized as valid until VREF stabilizes. 9) Values are shown per DDR SDRAM component Data Sheet 15 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Table 8 IDD Conditions Parameter Symbol Operating Current 0 one bank; active/ precharge; DQ, DM, and DQS inputs changing once per clock cycle; address and control inputs changing once every two clock cycles. IDD0 Operating Current 1 one bank; active/read/precharge; Burst Length = 4; see component data sheet. IDD1 Precharge Power-Down Standby Current all banks idle; power-down mode; CKE VIL,MAX IDD2P Precharge Floating Standby Current CS VIH,,MIN, all banks idle; CKE VIH,MIN; address and other control inputs changing once per clock cycle; VIN = VREF for DQ, DQS and DM. IDD2F Precharge Quiet Standby Current CS VIHMIN, all banks idle; CKE VIH,MIN; VIN = VREF for DQ, DQS and DM; address and other control inputs stable at VIH,MIN or VIL,MAX. IDD2Q Active Power-Down Standby Current one bank active; power-down mode; CKE VILMAX; VIN = VREF for DQ, DQS and DM. IDD3P Active Standby Current one bank active; CS VIH,MIN; CKE VIH,MIN; tRC = tRAS,MAX; DQ, DM and DQS inputs changing twice per clock cycle; address and control inputs changing once per clock cycle. IDD3N Operating Current Read one bank active; Burst Length = 2; reads; continuous burst; address and control inputs changing once per clock cycle; 50% of data outputs changing on every clock edge; CL = 2 for DDR266(A), CL = 3 for DDR333 and DDR400B; IOUT = 0 mA IDD4R Operating Current Write one bank active; Burst Length = 2; writes; continuous burst; address and control inputs changing once per clock cycle; 50% of data outputs changing on every clock edge; CL = 2 for DDR266(A), CL = 3 for DDR333 and DDR400B IDD4W Auto-Refresh Current tRC = tRFCMIN, burst refresh IDD5 Self-Refresh Current CKE 0.2 V; external clock on IDD6 Operating Current 7 four bank interleaving with Burst Length = 4; see component data sheet. IDD7 Data Sheet 16 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Symbol IDD0 IDD1 IDD2P IDD2F IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5 IDD6 IDD7 HYS72D128500HR-7-B HYS72D128300GBR-7-B HYS72D128321GBR-7-B HYS72D256320GBR-7-B IDD Specification for -7 HYS72D128500HR-7F-B Part Number & Organization Table 9 1 GB 1 GB 1 GB 2 GB x72 x72 x72 x72 1 Rank 1 Rank 2 Ranks 2 Ranks -7F -7 -7 -7 Unit Note 1)2) typ. max. typ. max. typ. max. typ. max. 2158 2452 2028 2298 1587 1776 2586 2964 mA 3) 2354 2746 2208 2568 1677 1911 2766 3234 mA 3)4) 430 448 430 448 430 448 484 520 mA 5) 736 808 736 808 736 808 1096 1240 mA 5) 646 754 646 754 646 754 916 1132 mA 5) 538 610 538 610 538 610 700 844 mA 5) 934 1042 934 1042 934 1042 1492 1708 mA 5) 2179 2460 2118 2388 1632 1821 2676 3054 mA 3)4) 2273 2554 2208 2478 1677 1866 2766 3144 mA 3) 4499 5263 4278 4998 2712 3126 4836 5664 mA 3) 414 468 414 468 414 468 451 560 mA 5) 5493 6376 5088 5898 3117 3576 5646 6564 mA 3)4) 1) DRAM component currents only 2) Test condition for maximum values: VDD = 2.7 V, TA = 10 C 3) The module IDDx values are calculated from the component IDDx data sheet values as: m x IDDx[component] + n x IDD3N[component] with m and n number of components of rank 1 and 2; n=0 for 1 rank modules 4) DQ I/O (IDDQ) currents are not included into calculations: module IDD values will be measured differently depending on load conditions 5) The module IDDx values are calculated from the corrponent IDDx data sheet values as: (m + n) x IDDx[component] Data Sheet 17 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Symbol IDD0 IDD1 IDD2P IDD2F IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5 IDD6 IDD7 HYS72D128321GBR-6-B HYS72D256320GBR-6-B IDD Specification for -6 HYS72D128300GBR-6-B Part Number & Organization Table 10 1GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -6 -6 -6 Unit Note 1)2) typ. max. typ. max. typ. max. 2350 2710 1873 2116 3016 3502 mA 3) 2620 2980 2008 2251 3286 3772 mA 3)4) 484 502 484 502 538 574 mA 5) 880 970 880 970 1330 1510 mA 5) 736 862 736 862 1042 1294 mA 5) 628 700 628 700 826 970 mA 5) 1096 1222 1096 1222 1762 2014 mA 5) 2620 2980 2008 2251 3286 3772 mA 3)4) 2710 3070 2053 2296 3376 3862 mA 3) 4690 5500 3043 3511 5356 6292 mA 3) 475 523.6 475 523.6 520 617.2 mA 5) 6310 7300 3853 4411 6976 8092 mA 3)4) 1) DRAM component currents only 2) Test condition for maximum values: VDD = 2.7 V, TA = 10 C 3) The module IDDx values are calculated from the component IDDx data sheet values as: m x IDDx[component] + n x IDD3N[component] with m and n number of components of rank 1 and 2; n=0 for 1 rank modules 4) DQ I/O (IDDQ) currents are not included into calculations: module IDD values will be measured differently depending on load conditions 5) The module IDDx values are calculated from the corrponent IDDx data sheet values as: (m + n) x IDDx[component] Data Sheet 18 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Symbol IDD0 IDD1 IDD2P IDD2F IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5 IDD6 IDD7 HYS72D128321GBR-5-B HYS72D256320GBR-5-B IDD Specification for -5 HYS72D128300GBR-5-B Part Number & Organization Table 11 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -5 -5 -5 Unit Note 1)2) typ. max. typ. max. typ. max. 2680 3040 3436 3940 3436 3940 mA 3) 2950 3400 3706 4300 3706 4300 mA 3)4) 698 734 752 824 752 824 mA 5) 1184 1292 1724 1940 1724 1940 mA 5) 986 1112 1328 1580 1328 1580 mA 5) 860 932 1076 1220 1076 1220 mA 5) 1400 1544 2156 2444 2156 2444 mA 5) 3040 3490 3796 4390 3796 4390 mA 3)4) 3130 3580 3886 4480 3886 4480 mA 3) 5290 6190 6046 7090 6046 7090 mA 3) 696.2 737.6 748.4 831.2 748.4 831.2 mA 5) 7090 8260 7846 9160 7846 9160 mA 3)4) 1) DRAM component currents only 2) Test condition for maximum values: VDD = 2.7 V, TA = 10 C 3) The module IDDx values are calculated from the component IDDx data sheet values as: m x IDDx[component] + n x IDD3N[component] with m and n number of components of rank 1 and 2; n=0 for 1 rank modules 4) DQ I/O (IDDQ) currents are not included into calculations: module IDD values will be measured differently depending on load conditions 5) The module IDDx values are calculated from the corrponent IDDx data sheet values as: (m + n) x IDDx[component] Data Sheet 19 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Table 12 AC Timing - Absolute Specifications -6/-5 Parameter DQ output access time from CK/CK DQS output access time from CK/CK CK high-level width CK low-level width Clock Half Period Symbol tAC tDQSCK tCH tCL tHP tCK -5 -6 DDR400B DDR333 Unit Note/ Test Condition 1) Min. Max. Min. Max. -0.6 +0.6 -0.7 +0.7 ns 2)3)4)5) -0.5 +0.5 -0.6 +0.6 ns 2)3)4)5) 0.45 0.55 0.45 0.55 2)3)4)5) 0.45 0.55 0.45 0.55 tCK tCK min. (tCL, tCH) ns 2)3)4)5) min. (tCL, tCH) 2)3)4)5) 5 12 -- -- ns CL = 3.0 2)3)4)5) 6 12 6 12 ns CL = 2.5 2)3)4)5) 7.5 12 7.5 12 ns CL = 2.0 2)3)4)5) 0.4 -- 0.45 -- ns 2)3)4)5) 0.4 -- 0.45 -- ns 2)3)4)5) 2.2 -- 2.2 -- ns 2)3)4)5)6) tDIPW Data-out high-impedance time from CK/CK tHZ Data-out low-impedance time from CK/CK tLZ st Write command to 1 DQS latching transition tDQSS DQS-DQ skew (DQS and associated DQ tDQSQ 1.75 -- 1.75 -- ns 2)3)4)5)6) -0.6 +0.6 -0.7 +0.7 ns 2)3)4)5)7) -0.6 +0.6 -0.7 +0.7 ns 2)3)4)5)7) 0.75 1.25 0.75 1.25 tCK 2)3)4)5) -- +0.40 -- +0.40 ns TFBGA 2)3)4)5) signals) -- +0.40 -- +0.45 ns TSOPII 2)3)4)5) -- +0.50 -- +0.50 ns TFBGA 2)3)4)5) -- +0.50 -- +0.55 ns TSOPII 2)3)4)5) Clock cycle time DQ and DM input hold time DQ and DM input setup time Control and Addr. input pulse width (each input) tDH tDS tIPW DQ and DM input pulse width (each input) Data hold skew factor tQHS tQH DQS input low (high) pulse width (write cycle) tDQSL,H DQS falling edge to CK setup time (write tDSS DQ/DQS output hold time tHP -tQHS tHP -tQHS ns 2)3)4)5) 0.35 -- 0.35 -- 2)3)4)5) 0.2 -- 0.2 -- tCK tCK 2)3)4)5) cycle) DQS falling edge hold time from CK (write cycle) tDSH 0.2 -- 0.2 -- tCK 2)3)4)5) Mode register set command cycle time tMRD tWPRES tWPST tWPRE tIS 2 -- 2 -- tCK 2)3)4)5) 0 -- 0 -- ns 2)3)4)5)8) 0.40 0.60 0.40 0.60 2)3)4)5)9) 0.25 -- 0.25 -- tCK tCK 0.6 -- 0.75 -- ns fast slew rate Write preamble setup time Write postamble Write preamble Address and control input setup time 2)3)4)5) 3)4)5)6)10) 0.7 -- 0.8 -- ns slow slew rate 3)4)5)6)10) Address and control input hold time tIH 0.6 -- 0.75 -- ns fast slew rate 3)4)5)6)10) 0.7 -- 0.8 -- ns slow slew rate 3)4)5)6)10) Read preamble Read postamble Data Sheet tRPRE tRPST 0.9 1.1 0.9 1.1 0.40 0.60 0.40 0.60 20 tCK tCK 2)3)4)5) 2)3)4)5) Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Table 12 AC Timing - Absolute Specifications -6/-5 (cont'd) Parameter Symbol -5 -6 DDR400B DDR333 Unit Note/ Test Condition 1) Min. Max. Min. Max. tRAS tRC 40 70E+3 42 70E+3 ns 2)3)4)5) 55 -- 60 -- ns 2)3)4)5) Auto-refresh to Active/Auto-refresh command period tRFC 65 -- 72 -- ns 2)3)4)5) Active to Read or Write delay tRCD tRP tRAP tRRD tWR tDAL 15 -- 18 -- ns 2)3)4)5) 15 -- 18 -- ns 2)3)4)5) 15 -- 18 -- ns 2)3)4)5) 10 -- 12 -- ns 2)3)4)5) 15 -- 15 -- ns 2)3)4)5) (tWR/tCK) + (tRP/tCK) tCK 2)3)4)5)11) tWTR tXSNR tXSRD tREFI 1 -- 1 -- tCK 2)3)4)5) 75 -- 75 -- ns 2)3)4)5) Active to Precharge command Active to Active/Auto-refresh command period Precharge command period Active to Autoprecharge delay Active bank A to Active bank B command Write recovery time Auto precharge write recovery + precharge time Internal write to read command delay Exit self-refresh to non-read command Exit self-refresh to read command Average Periodic Refresh Interval (tWR/tCK) + (tRP/tCK) 200 -- 200 -- tCK 2)3)4)5) -- 7.8 -- 7.8 s 2)3)4)5)12) 1) 0 C TA 70 C; VDDQ = 2.5 V 0.2 V, VDD = +2.5 V 0.2 V (DDR333); VDDQ = 2.6 V 0.1 V, VDD = +2.6 V 0.1 V (DDR400) 2) Input slew rate 1 V/ns for DDR400, DDR333 3) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross: the input reference level for signals other than CK/CK, is VREF. CK/CK slew rate are 1.0 V/ns. 4) Inputs are not recognized as valid until VREF stabilizes. 5) The Output timing reference level, as measured at the timing reference point indicated in AC Characteristics (note 3) is VTT. 6) These parameters guarantee device timing, but they are not necessarily tested on each device. 7) tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referred to a specific voltage level, but specify when the device is no longer driving (HZ), or begins driving (LZ). 8) The specific requirement is that DQS be valid (HIGH, LOW, or some point on a valid transition) on or before this CK edge. A valid transition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in progress on the bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS. 9) The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 10) Fast slew rate 1.0 V/ns , slow slew rate 0.5 V/ns and < 1 V/ns for command/address and CK & CK slew rate > 1.0 V/ns, measured between VOH(ac) and VOL(ac). 11) For each of the terms, if not already an integer, round to the next highest integer. tCK is equal to the actual system clock cycle time. 12) A maximum of eight Autorefresh commands can be posted to any given DDR SDRAM device. Data Sheet 21 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Table 13 AC Timing - Absolute Specifications -7/-7F Parameter Symbol -7F -7 DDR266 DDR266A Min. DQ output access time from CK/CK DQS output access time from CK/CK CK high-level width CK low-level width Clock Half Period Clock cycle time tAC tDQSCK tCH tCL tHP tCK Max. Min. Unit Note/ Test Condition 1)1) Max. -0.75 +0.75 -0.75 +0.75 ns 2)2)3)3)4)4)5)5) -0.75 +0.75 -0.75 +0.75 ns 2)3)4)5) 0.45 0.55 0.45 0.55 2)3)4)5) 0.45 0.55 0.45 0.55 tCK tCK ns 2)3)4)5) ns CL = 2.5 min. (tCL, tCH) 7.5 12 min. (tCL, tCH) 7.5 12 2)3)4)5) 2)3)4)5) 7.5 12 7.5 12 ns CL = 2.0 2)3)4)5) tDH DQ and DM input setup time tDS Control and Addr. input pulse width (each input) tIPW DQ and DM input pulse width (each input) tDIPW Data-out high-impedance time from CK/CK tHZ Data-out low-impedance time from CK/CK tLZ Write command to 1st DQS latching transition tDQSS DQS-DQ skew (DQS and associated DQ tDQSQ DQ and DM input hold time 0.5 -- 0.5 -- ns 2)3)4)5) 0.5 -- 0.5 -- ns 2)3)4)5) 2.2 -- 2.2 -- ns 2)3)4)5)6) 1.75 -- 1.75 -- ns 2)3)4)5)6) 2)3)4)5)7) -0.75 +0.75 -0.75 +0.75 ns -0.75 +0.75 -0.75 +0.75 ns 2)3)4)5)7) 0.75 1.25 0.75 1.25 tCK 2)3)4)5) -- +0.5 -- +0.5 ns TFBGA 2)3)4)5) signals) -- +0.5 -- +0.5 ns TSOPII 2)3)4)5) Data hold skew factor tQHS -- +0.75 -- +0.75 ns TFBGA 2)3)4)5) -- +0.75 -- +0.75 ns TSOPII 2)3)4)5) tQH DQS input low (high) pulse width (write cycle) tDQSL,H DQS falling edge to CK setup time (write cycle) tDSS DQS falling edge hold time from CK (write cycle) tDSH Mode register set command cycle time tMRD Write preamble setup time tWPRES Write postamble tWPST Write preamble tWPRE Address and control input setup time tIS DQ/DQS output hold time tHP - tQHS tHP - tQHS ns 2)3)4)5) 0.35 -- 0.35 -- 2)3)4)5) 0.2 -- 0.2 -- 0.2 -- 0.2 -- 2 -- 2 -- tCK tCK tCK tCK 0 -- 0 -- ns 2)3)4)5)8) 0.40 0.60 0.40 0.60 2)3)4)5)9) 0.25 -- 0.25 -- tCK tCK 0.9 -- 0.9 -- ns fast slew rate 2)3)4)5) 2)3)4)5) 2)3)4)5) 2)3)4)5) 3)4)5)6)10) 0.9 -- 0.9 -- ns slow slew rate 3)4)5)6)10) Data Sheet 22 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics Table 13 AC Timing - Absolute Specifications -7/-7F Parameter Address and control input hold time Symbol tIH -7F -7 DDR266 DDR266A Min. Max. Min. Max. 0.9 -- 0.9 -- Unit Note/ Test Condition 1)1) ns fast slew rate 3)4)5)6)10) 1.0 -- 1.0 -- ns slow slew rate 3)4)5)6)10) Read preamble Read postamble Active to Precharge command Active to Active/Auto-refresh command period Auto-refresh to Active/Auto-refresh command period tRPRE tRPST tRAS tRC tRFC tRCD Precharge command period tRP Active to Autoprecharge delay tRAP Active bank A to Active bank B command tRRD Write recovery time tWR Auto precharge write recovery + precharge time tDAL Active to Read or Write delay Internal write to read command delay Exit self-refresh to non-read command Exit self-refresh to read command Average Periodic Refresh Interval tCK tCK 2)3)4)5) 120E+3 45 120E+3 ns 2)3)4)5) 65 -- 65 -- ns 2)3)4)5) 75 -- 75 -- ns 2)3)4)5) 20 -- 20 -- ns 2)3)4)5) 20 -- 20 -- ns 2)3)4)5) 20 -- 20 -- ns 2)3)4)5) 15 -- 15 -- ns 2)3)4)5) 15 -- 15 -- ns 2)3)4)5) tCK 2)3)4)5)11) 0.9 1.1 0.9 1.1 0.40 0.60 0.40 0.60 45 (tWR/tCK) + (tRP/tCK) tWTR tXSNR tXSRD tREFI (tWR/tCK) + (tRP/tCK) 2)3)4)5) 1 -- 1 -- tCK 2)3)4)5) 75 -- 75 -- ns 2)3)4)5) 200 -- 200 -- tCK 2)3)4)5) -- 7.8 -- 7.8 s 2)3)4)5)12) 1) 0 C TA 70 C; VDDQ = 2.5 V 0.2 V, VDD = +2.5 V 0.2 V (DDR333); VDDQ = 2.6 V 0.1 V, VDD = +2.6 V 0.1 V (DDR400) 2) Input slew rate 1 V/ns for DDR400, DDR333 3) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross: the input reference level for signals other than CK/CK, is VREF. CK/CK slew rate are 1.0 V/ns. 4) Inputs are not recognized as valid until VREF stabilizes. 5) The Output timing reference level, as measured at the timing reference point indicated in AC Characteristics (note 3) is VTT. 6) These parameters guarantee device timing, but they are not necessarily tested on each device. 7) tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referred to a specific voltage level, but specify when the device is no longer driving (HZ), or begins driving (LZ). 8) The specific requirement is that DQS be valid (HIGH, LOW, or some point on a valid transition) on or before this CK edge. A valid transition is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in progress on the bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from HIGH to LOW at this time, depending on tDQSS. 9) The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 10) Fast slew rate 1.0 V/ns , slow slew rate 0.5 V/ns and < 1 V/ns for command/address and CK & CK slew rate > 1.0 V/ns, measured between VOH(ac) and VOL(ac). Data Sheet 23 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Electrical Characteristics 11) For each of the terms, if not already an integer, round to the next highest integer. tCK is equal to the actual system clock cycle time. 12) A maximum of eight Autorefresh commands can be posted to any given DDR SDRAM device. Data Sheet 24 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents SPD Codes for HYS72D[128/256][300/321/320]GBR-5-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -5 -5 -5 Label Code PC3200R-30331 PC3200R-30331 PC3200R-30331 JEDEC SPD Revision Rev. 1.0 Rev. 1.0 Rev. 1.0 Description HEX HEX HEX 0 Programmed SPD Bytes in E2PROM 80 80 80 1 Total number of Bytes in E2PROM 08 08 08 2 Memory Type (DDR = 07h) 07 07 07 3 Number of Row Addresses 0D 0D 0D 4 Number of Column Addresses 0C 0B 0C 5 Number of DIMM Ranks 01 02 02 6 Data Width (LSB) 48 48 48 7 Data Width (MSB) 00 00 00 8 Interface Voltage Levels 04 04 04 9 tCK @ CLmax (Byte 18) [ns] 50 50 50 10 tAC SDRAM @ CLmax (Byte 18) [ns] 50 50 50 11 Error Correction Support (non- / ECC) 02 02 02 12 Refresh Rate 82 82 82 13 Primary SDRAM Width 04 08 04 14 Error Checking SDRAM Width 04 08 04 15 tCCD [cycles] 01 01 01 16 Burst Length Supported 0E 0E 0E 17 Number of Banks on SDRAM Device 04 04 04 18 CAS Latency 1C 1C 1C 19 CS Latency 01 01 01 20 Write Latency 02 02 02 21 DIMM Attributes 26 26 26 22 Component Attributes C1 C1 C1 23 tCK @ CLmax -0.5 (Byte 18) [ns] 60 60 60 Part Number & Organization HYS72D256320GBR-5-B Table 14 HYS72D128321GBR-5-B SPD Contents HYS72D128300GBR-5-B 4 Byte# 24 tAC SDRAM @ CLmax -0.5 [ns] 50 50 50 25 tCK @ CLmax -1 (Byte 18) [ns] 75 75 75 Data Sheet 25 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-5-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -5 -5 -5 Label Code PC3200R-30331 PC3200R-30331 PC3200R-30331 JEDEC SPD Revision Rev. 1.0 Rev. 1.0 Rev. 1.0 Description HEX HEX HEX 26 tAC SDRAM @ CLmax -1 [ns] 50 50 50 27 tRPmin [ns] 3C 3C 3C 28 tRRDmin [ns] 28 28 28 29 tRCDmin [ns] 3C 3C 3C 30 tRASmin [ns] 28 28 28 31 Module Density per Rank 01 80 01 32 tAS, tCS [ns] 60 60 60 33 tAH, TCH [ns] 60 60 60 34 tDS [ns] 40 40 40 35 tDH [ns] 40 40 40 36 - 40 not used 00 00 00 41 tRCmin [ns] 37 37 37 42 tRFCmin [ns] 41 41 41 43 tCKmax [ns] 28 28 28 44 tDQSQmax [ns] 28 28 28 45 tQHSmax [ns] 50 50 50 46 not used 00 00 00 47 DIMM PCB Height 01 01 01 48 - 61 not used 00 00 00 62 SPD Revision 10 10 10 63 Checksum of Byte 0-62 E1 68 E2 64 JEDEC ID Code of Infineon (1) C1 C1 C1 65 - 71 JEDEC ID Code of Infineon (2) 00 00 00 72 Module Manufacturer Location xx xx xx 73 Part Number, Char 1 37 37 37 74 Part Number, Char 2 32 32 32 75 Part Number, Char 3 44 44 44 Part Number & Organization HYS72D128321GBR-5-B SPD Codes for HYS72D[128/256][300/321/320]GBR-5-B HYS72D128300GBR-5-B Table 14 Byte# Data Sheet 26 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-5-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -5 -5 -5 Label Code PC3200R-30331 PC3200R-30331 PC3200R-30331 JEDEC SPD Revision Rev. 1.0 Rev. 1.0 Rev. 1.0 Description HEX HEX HEX 76 Part Number, Char 4 31 31 32 77 Part Number, Char 5 32 32 35 78 Part Number, Char 6 38 38 36 79 Part Number, Char 7 33 33 33 80 Part Number, Char 8 30 32 32 81 Part Number, Char 9 30 31 30 82 Part Number, Char 10 47 47 47 83 Part Number, Char 11 42 42 42 84 Part Number, Char 12 52 52 52 85 Part Number, Char 13 35 35 35 86 Part Number, Char 14 42 42 42 87 Part Number, Char 15 20 20 20 88 Part Number, Char 16 20 20 20 89 Part Number, Char 17 20 20 20 90 Part Number, Char 18 20 20 20 91 Module Revision Code xx xx xx Part Number & Organization HYS72D128321GBR-5-B SPD Codes for HYS72D[128/256][300/321/320]GBR-5-B HYS72D128300GBR-5-B Table 14 Byte# 92 Test Program Revision Code xx xx xx 93 Module Manufacturing Date Year xx xx xx 94 Module Manufacturing Date Week xx xx xx 95 - 98 Module Serial Number (1 - 4) xx xx xx 00 00 00 99 - 127 not used Data Sheet 27 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-6-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -6 -6 -6 Label Code PC2700R-25330 PC2700R-25330 PC2700R-25330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Rev. 0.0 Description HEX HEX HEX 0 Programmed SPD Bytes in E2PROM 80 80 80 1 Total number of Bytes in E2PROM 08 08 08 2 Memory Type (DDR = 07h) 07 07 07 3 Number of Row Addresses 0D 0D 0D 4 Number of Column Addresses 0C 0B 0C 5 Number of DIMM Ranks 01 02 02 6 Data Width (LSB) 48 48 48 7 Data Width (MSB) 00 00 00 8 Interface Voltage Levels 04 04 04 9 tCK @ CLmax (Byte 18) [ns] 60 60 60 10 tAC SDRAM @ CLmax (Byte 18) [ns] 70 70 70 11 Error Correction Support (non- / ECC) 02 02 02 12 Refresh Rate 82 82 82 13 Primary SDRAM Width 04 08 04 14 Error Checking SDRAM Width 04 08 04 15 tCCD [cycles] 01 01 01 16 Burst Length Supported 0E 0E 0E 17 Number of Banks on SDRAM Device 04 04 04 18 CAS Latency 0C 0C 0C 19 CS Latency 01 01 01 20 Write Latency 02 02 02 21 DIMM Attributes 26 26 26 22 Component Attributes C1 C1 C1 23 tCK @ CLmax -0.5 (Byte 18) [ns] 75 75 75 Part Number & Organization HYS72D128321GBR-6-B SPD Codes for HYS72D[128/256][300/321/320]GBR-6-B HYS72D128300GBR-6-B Table 15 Byte# 24 tAC SDRAM @ CLmax -0.5 [ns] 70 70 70 25 tCK @ CLmax -1 (Byte 18) [ns] 00 00 00 Data Sheet 28 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-6-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -6 -6 -6 Label Code PC2700R-25330 PC2700R-25330 PC2700R-25330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Rev. 0.0 Description HEX HEX HEX 26 tAC SDRAM @ CLmax -1 [ns] 00 00 00 27 tRPmin [ns] 48 48 48 28 tRRDmin [ns] 30 30 30 29 tRCDmin [ns] 48 48 48 30 tRASmin [ns] 2A 2A 2A 31 Module Density per Rank 01 80 01 32 tAS, tCS [ns] 75 75 75 33 tAH, TCH [ns] 75 75 75 34 tDS [ns] 45 45 45 35 tDH [ns] 45 45 45 36 - 40 not used 00 00 00 41 tRCmin [ns] 3C 3C 3C 42 tRFCmin [ns] 48 48 48 43 tCKmax [ns] 30 30 30 44 tDQSQmax [ns] 28 28 28 45 tQHSmax [ns] 50 50 50 46 not used 00 00 00 47 DIMM PCB Height 00 00 00 48 - 61 not used 00 00 00 62 SPD Revision 00 00 00 63 Checksum of Byte 0-62 CA 51 CB 64 JEDEC ID Code of Infineon (1) C1 C1 C1 65 - 71 JEDEC ID Code of Infineon (2 - 8) 00 00 00 72 Module Manufacturer Location xx xx xx 73 Part Number, Char 1 37 37 37 74 Part Number, Char 2 32 32 32 75 Part Number, Char 3 44 44 44 Part Number & Organization HYS72D128321GBR-6-B SPD Codes for HYS72D[128/256][300/321/320]GBR-6-B HYS72D128300GBR-6-B Table 15 Byte# Data Sheet 29 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-6-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks -6 -6 -6 Label Code PC2700R-25330 PC2700R-25330 PC2700R-25330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Rev. 0.0 Description HEX HEX HEX 76 Part Number, Char 4 31 31 32 77 Part Number, Char 5 32 32 35 78 Part Number, Char 6 38 38 36 79 Part Number, Char 7 33 33 33 80 Part Number, Char 8 30 32 32 81 Part Number, Char 9 30 31 30 82 Part Number, Char 10 47 47 47 83 Part Number, Char 11 42 42 42 84 Part Number, Char 12 52 52 52 85 Part Number, Char 13 36 36 36 86 Part Number, Char 14 42 42 42 87 Part Number, Char 15 20 20 20 88 Part Number, Char 16 20 20 20 89 Part Number, Char 17 20 20 20 90 Part Number, Char 18 20 20 20 91 Module Revision Code xx xx xx Part Number & Organization HYS72D128321GBR-6-B SPD Codes for HYS72D[128/256][300/321/320]GBR-6-B HYS72D128300GBR-6-B Table 15 Byte# 92 Test Program Revision Code xx xx xx 93 Module Manufacturing Date Year xx xx xx 94 Module Manufacturing Date Week xx xx xx 95 - 98 Module Serial Number (1 - 4) xx xx xx 00 00 00 99 - 127 not used Data Sheet 30 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-7-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks reg reg reg Label Code PC2100R-20330 PC2100R-20330 PC2100R-20330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Rev. 0.0 Description HEX HEX HEX 0 Programmed SPD Bytes in E2PROM 80 80 80 1 Total number of Bytes in E2PROM 08 08 08 2 Memory Type (DDR = 07h) 07 07 07 3 Number of Row Addresses 0D 0D 0D 4 Number of Column Addresses 0C 0B 0C 5 Number of DIMM Ranks 01 02 02 6 Data Width (LSB) 48 48 48 7 Data Width (MSB) 00 00 00 8 Interface Voltage Levels 04 04 04 9 tCK @ CLmax (Byte 18) [ns] 70 70 70 10 tAC SDRAM @ CLmax (Byte 18) [ns] 75 75 75 11 Error Correction Support (non- / ECC) 02 02 02 12 Refresh Rate 82 82 82 13 Primary SDRAM Width 04 08 04 14 Error Checking SDRAM Width 04 08 04 15 tCCD [cycles] 01 01 01 16 Burst Length Supported 0E 0E 0E 17 Number of Banks on SDRAM Device 04 04 04 18 CAS Latency 0C 0C 0C 19 CS Latency 01 01 01 20 Write Latency 02 02 02 21 DIMM Attributes 26 26 26 22 Component Attributes C1 C1 C1 23 tCK @ CLmax -0.5 (Byte 18) [ns] 75 75 75 Part Number & Organization HYS72D128321GBR-7-B SPD Codes for HYS72D[128/256][300/321/320]GBR-7-B HYS72D128300GBR-7-B Table 16 Byte# 24 tAC SDRAM @ CLmax -0.5 [ns] 75 75 75 25 tCK @ CLmax -1 (Byte 18) [ns] 00 00 00 Data Sheet 31 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-7-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks reg reg reg Label Code PC2100R-20330 PC2100R-20330 PC2100R-20330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Rev. 0.0 Description HEX HEX HEX 26 tAC SDRAM @ CLmax -1 [ns] 00 00 00 27 tRPmin [ns] 50 50 50 28 tRRDmin [ns] 3C 3C 3C 29 tRCDmin [ns] 50 50 50 30 tRASmin [ns] 2D 2D 2D 31 Module Density per Rank 01 80 01 32 tAS, tCS [ns] 90 90 90 33 tAH, TCH [ns] 90 90 90 34 tDS [ns] 50 50 50 35 tDH [ns] 50 50 50 36 - 40 not used 00 00 00 41 tRCmin [ns] 41 41 41 42 tRFCmin [ns] 4B 4B 4B 43 tCKmax [ns] 30 30 30 44 tDQSQmax [ns] 32 32 32 45 tQHSmax [ns] 75 75 75 46 not used 00 00 00 47 DIMM PCB Height 00 00 00 48 - 61 not used 00 00 00 62 SPD Revision 00 00 00 63 Checksum of Byte 0-62 86 0D 87 64 JEDEC ID Code of Infineon (1) C1 C1 C1 65 - 71 JEDEC ID Code of Infineon (2 - 8) 00 00 00 72 Module Manufacturer Location xx xx xx 73 Part Number, Char 1 37 37 37 74 Part Number, Char 2 32 32 32 75 Part Number, Char 3 44 44 44 Part Number & Organization HYS72D128321GBR-7-B SPD Codes for HYS72D[128/256][300/321/320]GBR-7-B HYS72D128300GBR-7-B Table 16 Byte# Data Sheet 32 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D256320GBR-7-B 1 GB 1 GB 2 GB x72 x72 x72 1 Rank 2 Ranks 2 Ranks reg reg reg Label Code PC2100R-20330 PC2100R-20330 PC2100R-20330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Rev. 0.0 Description HEX HEX HEX 76 Part Number, Char 4 31 31 32 77 Part Number, Char 5 32 32 35 78 Part Number, Char 6 38 38 36 79 Part Number, Char 7 33 33 33 80 Part Number, Char 8 30 32 32 81 Part Number, Char 9 30 31 30 82 Part Number, Char 10 47 47 47 83 Part Number, Char 11 42 42 42 84 Part Number, Char 12 52 52 52 85 Part Number, Char 13 37 37 37 86 Part Number, Char 14 42 42 42 87 Part Number, Char 15 20 20 20 88 Part Number, Char 16 20 20 20 89 Part Number, Char 17 20 20 20 90 Part Number, Char 18 20 20 20 91 Module Revision Code xx xx xx Part Number & Organization HYS72D128321GBR-7-B SPD Codes for HYS72D[128/256][300/321/320]GBR-7-B HYS72D128300GBR-7-B Table 16 Byte# 92 Test Program Revision Code xx xx xx 93 Module Manufacturing Date Year xx xx xx 94 Module Manufacturing Date Week xx xx xx 95 - 98 Module Serial Number (1 - 4) xx xx xx 00 00 00 99 - 127 not used Data Sheet 33 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D128500HR-7F-B HYS72D128500HR-7-B SPD Codes for HYS72D128500HR-[7F/7]-B Part Number & Organization Table 17 1 GB 1 GB x72 x72 1 Rank 1 Rank reg reg Label Code PC2100R-20220 PC2100R-20330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Description HEX HEX 0 Programmed SPD Bytes in E2PROM 80 80 1 Total number of Bytes in E2PROM 08 08 2 Memory Type (DDR = 07h) 07 07 3 Number of Row Addresses 0D 0D Byte# 4 Number of Column Addresses 0C 0C 5 Number of DIMM Ranks 01 01 6 Data Width (LSB) 48 48 7 Data Width (MSB) 00 00 8 Interface Voltage Levels 04 04 9 tCK @ CLmax (Byte 18) [ns] 70 70 10 tAC SDRAM @ CLmax (Byte 18) [ns] 75 75 11 Error Correction Support (non- / ECC) 02 02 12 Refresh Rate 82 82 13 Primary SDRAM Width 04 04 14 Error Checking SDRAM Width 04 04 15 tCCD [cycles] 01 01 16 Burst Length Supported 0E 0E 17 Number of Banks on SDRAM Device 04 04 18 CAS Latency 0C 0C 19 CS Latency 01 01 20 Write Latency 02 02 21 DIMM Attributes 26 26 22 Component Attributes C1 C1 23 tCK @ CLmax -0.5 (Byte 18) [ns] 75 75 24 tAC SDRAM @ CLmax -0.5 [ns] 75 75 25 tCK @ CLmax -1 (Byte 18) [ns] 00 00 Data Sheet 34 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D128500HR-7F-B HYS72D128500HR-7-B SPD Codes for HYS72D128500HR-[7F/7]-B Part Number & Organization Table 17 1 GB 1 GB x72 x72 1 Rank 1 Rank reg reg Label Code PC2100R-20220 PC2100R-20330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Description HEX HEX 26 tAC SDRAM @ CLmax -1 [ns] 00 00 27 tRPmin [ns] 3C 50 28 tRRDmin [ns] 3C 3C 29 tRCDmin [ns] 3C 50 30 tRASmin [ns] 2D 2D 31 Module Density per Rank 01 01 32 tAS, tCS [ns] 90 90 33 tAH, TCH [ns] 90 90 34 tDS [ns] 50 50 35 tDH [ns] 50 50 36 - 40 not used 00 00 41 tRCmin [ns] 3C 41 42 tRFCmin [ns] 4B 4B 43 tCKmax [ns] 30 30 44 tDQSQmax [ns] 32 32 45 tQHSmax [ns] 75 75 46 not used 00 00 47 DIMM PCB Height 00 00 48 - 61 not used 00 00 62 SPD Revision 00 00 63 Checksum of Byte 0-62 59 86 64 JEDEC ID Code of Infineon (1) C1 C1 65 - 71 JEDEC ID Code of Infineon (2 - 8) 00 00 72 Module Manufacturer Location xx xx 73 Part Number, Char 1 37 37 74 Part Number, Char 2 32 32 75 Part Number, Char 3 44 44 Byte# Data Sheet 35 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module SPD Contents HYS72D128500HR-7F-B HYS72D128500HR-7-B SPD Codes for HYS72D128500HR-[7F/7]-B Part Number & Organization Table 17 1 GB 1 GB x72 x72 1 Rank 1 Rank reg reg Label Code PC2100R-20220 PC2100R-20330 Jedec SPD Revision Rev. 0.0 Rev. 0.0 Description HEX HEX 76 Part Number, Char 4 31 31 77 Part Number, Char 5 32 32 78 Part Number, Char 6 38 38 79 Part Number, Char 7 35 35 80 Part Number, Char 8 30 30 81 Part Number, Char 9 30 30 82 Part Number, Char 10 48 48 83 Part Number, Char 11 52 52 84 Part Number, Char 12 37 37 85 Part Number, Char 13 46 42 86 Part Number, Char 14 42 20 87 Part Number, Char 15 20 20 88 Part Number, Char 16 20 20 89 Part Number, Char 17 20 20 90 Part Number, Char 18 20 20 91 Module Revision Code xx xx 92 Test Program Revision Code xx xx 93 Module Manufacturing Date Year xx xx 94 Module Manufacturing Date Week xx xx 95 - 98 Module Serial Number (1 - 4) xx xx 99 - 127 not used 00 00 Byte# Data Sheet 36 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Package Outlines Package Outlines 0.1 A B C 5 133.35 0.15 A B C 128.95 4 MAX. 28.58 0.13 4 0.1 A 1 2.5 0.1 o0.1 A B C 92 6.62 B C 2.175 0.4 6.35 64.77 1.27 0.1 49.53 1.8 0.1 0.1 A B C 184 17.8 93 10 3.8 0.13 95 x 1.27 = 120.65 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C Burr max. 0.4 allowed L-DIM-184-22-2 Figure 4 Data Sheet Package Outline - Raw Card C DDR Registered DIMM HYS72D128300GBR-[5/6/7]-B 37 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module 0.1 A B C Package Outlines 133.35 0.15 A B C 128.95 4 MAX. 28.58 0.13 4 0.1 A 1 2.5 0.1 o0.1 A B C 92 6.62 B C 2.175 0.4 6.35 64.77 1.27 0.1 49.53 1.8 0.1 0.1 A B C 184 17.8 93 10 3.8 0.13 95 x 1.27 = 120.65 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C Burr max. 0.4 allowed L-DIM-184-23-2 Figure 5 Data Sheet Package Outline - Raw Card B DDR Registered DIMM HYS72D128321HR-[5/6/7]-B 38 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Package Outlines 0.1 A B C 133.35 0.15 A B C 128.95 4 MAX. 30.48 0.13 4 0.1 A 92 o0.1 A B C B C 6.62 2.175 0.4 6.35 49.53 1.8 0.1 0.1 A B C 93 184 10 3.8 0.13 64.77 1.27 0.1 17.8 1 2.5 0.1 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C L-DIM-184-25 Burr max. 0.4 allowed Figure 6 Data Sheet Package Outline - Raw Card D DDR Registered DIMM HYS72D256320GBR-[5/6/7]-B 39 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Package Outlines 0.1 A B C 133.35 0.15 A B C 128.95 4 MAX. A 30.48 0.13 4 0.1 1) 1 2.5 0.1 o0.1 A B C 92 6.62 B C 2.175 0.4 6.35 64.77 1.27 0.1 49.53 0.1 A B C 93 184 17.8 1.8 0.1 10 3.8 0.13 95 x 1.27 = 120.65 1) 3 MIN. 0.2 2.5 0.2 Detail of contacts 1.27 1 0.05 0.1 A B C 1) On ECC modules only Burr max. 0.4 allowed Figure 7 Data Sheet L-DIM-184-12-3 Package Outline - Raw Card M DDR Registered DIMM HYS72D128500HR-[7/7F]-B 40 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Application Note 6 Application Note Power Up and Power Management on DDR Registered DIMMs (according to JEDEC ballot JC-42.5 Item 1173) 184-pin Double Data Rate (DDR) Registered DIMMs include two new features to facilitate controlled power-up and to minimize power consumption during low power mode. One feature is externally controlled via a systemgenerated RESET signal; the second is based on module detection of the input clocks. These enhancements permit the modules to power up with SDRAM outputs in a High-Z state (eliminating risk of high current dissipations and/or dotted I/Os), and result in the powering-down of module support devices (registers and Phase-Locked Loop) when the memory is in Self-Refresh mode. The new RESET pin controls power dissipation on the module's registers and ensures that CKE and other SDRAM inputs are maintained at a valid `low' level during power-up and self refresh. When RESET is at a low level, all the register outputs are forced to a low level, and all differential register input receivers are powered down, resulting in very low register power consumption. The RESET pin, located on DIMM tab #10, is driven from the system as an asynchronous signal according to the attached details. Using this function also permits the system and DIMM clocks to be stopped during memory Self Refresh operation, while ensuring that the SDRAMs stay in Self Refresh mode. Table 18 The function for RESET is as follows:1) Register Inputs Register Outputs RESET CK CK Data in (D) Data out (Q) H Rising Falling H H H Rising Falling L L H L or H L or H X Qo H High Z High Z X Illegal input conditions L X or Hi-Z X or Hi-Z X or Hi-Z L 1) X : Don't care, Hi-Z : High Impedance, Qo: Data latched at the previous of CK risning and CK falling As described in the table above, a low on the RESET input ensures that the Clock Enable (CKE) signal(s) are maintained low at the SDRAM pins (CKE being one of the 'Q' signals at the register output). Holding CKE low maintains a high impedance state on the SDRAM DQ, DQS and DM outputs -- where they will remain until activated by a valid `read' cycle. CKE low also maintains SDRAMs in Self Refresh mode when applicable. The DDR PLL devices automatically detect clock activity above 20MHz. When an input clock frequency of 20MHz or greater is detected, the PLL begins operation and initiates clock frequency lock (the minimum operating frequency at which all specifications will be met is 95MHz). If the clock input frequency drops below 20MHz (actual detect frequency will vary by vendor), the PLL VCO (Voltage Controlled Oscillator) is stopped, outputs are made High-Z, and the differential inputs are powered down -- resulting in a total PLL current consumption of less than 1mA. Use of this low power PLL function makes the use of the PLL RESET (or G pin) unnecessary, and it is tied inactive on the DIMM. This application note describes the required and optional system sequences associated with the DDR Registered DIMM 'RESET' function. It is important to note that all references to CKE refer to both CKE0 and CKE1 for a 2bank DIMM. Because RESET applies to all DIMM register devices, it is therefore not possible to uniquely control CKE to one physical DIMM bank through the use of the RESET pin. Data Sheet 41 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Application Note Power-Up Sequence with RESET -- Required 1. The system sets RESET at a valid low level. This is the preferred default state during power-up. This input condition forces all register outputs to a low state independent of the condition on the register inputs (data and clock), ensuring that CKE is at a stable low-level at the DDR SDRAMs. 2. The power supplies should be initialized according to the JEDEC-approved initialization sequence for DDR SDRAMs. 3. Stabilization of Clocks to the SDRAM The system must drive clocks to the application frequency (PLL operation is not assured until the input clock reaches 20MHz). Stability of clocks at the SDRAMs will be affected by all applicable system clock devices, and time must be allotted to permit all clock devices to settle. Once a stable clock is received at the DIMM PLL, the required PLL stabilization time (assuming power to the DIMM is stable) is 100 microseconds. When a stable clock is present at the SDRAM input (driven from the PLL), the DDR SDRAM requires 200 sec prior to SDRAM operation. 4. The system applies valid logic levels to the data inputs of the register (address and controls at the DIMM connector). CKE must be maintained low and all other inputs should be driven to a known state. In general these commands can be determined by the system designer. One option is to apply an SDRAM `NOP' command (with CKE low), as this is the first command defined by the JEDEC initialization sequence (ideally this would be a `NOP Deselect' command). A second option is to apply low levels on all of the register inputs to be consistent with the state of the register outputs. 5. The system switches RESET to a logic `high' level. The SDRAM is now functional and prepared to receive commands. Since the RESET signal is asynchronous, setting the RESET timing in relation to a specific clock edge is not required (during this period, register inputs must remain stable). 6. The system must maintain stable register inputs until normal register operation is attained. The registers have an activation time that allows their clock receivers, data input receivers, and output drivers sufficient time to be turned on and become stable. During this time the system must maintain the valid logic levels described in step 5. It is also a functional requirement that the registers maintain a low state at the CKE outputs to guarantee that the DDR SDRAMs continue to receive a low level on CKE. Register activation time (t (ACT) ), from asynchronous switching of RESET from low to high until the registers are stable and ready to accept an input signal, is specified in the register and DIMM do-umentation. 7. The system can begin the JEDEC-defined DDR SDRAM power-up sequence (according to the JEDECpproved initialization sequence). Self Refresh Entry (RESET low, clocks powered off) -- Optional Self Refresh can be used to retain data in DDR SDRAM DIMMs even if the rest of the system is powered down and the clocks are off. This mode allows the DDR SDRAMs on the DIMM to retain data without external clocking. Self Refresh mode is an ideal time to utilize the RESET pin, as this can reduce register power consumption (RESET low deactivates register CK and CK, data input receivers, and data output drivers). 1. The system applies Self Refresh entry command. (CKELow, CSLow, RAS Low, CAS Low, WE High) Note: Note: The commands reach the DDR SDRAM one clock later due to the additional register pipelining on a Registered DIMM. After this command is issued to the SDRAM, all of the address and control and clock input conditions to the SDRAM are Don't Cares-- with the exception of CKE. 2. The system sets RESET at a valid low level. This input condition forces all register outputs to a low state, independent of the condition on the registerm inputs (data and clock), and ensures that CKE, and all other control and address signals, are a stable low-level at the DDR SDRAMs. Since the RESET signal is asynchronous, setting the RESET timing in relation to a specific clock edge is not required. 3. The system turns off clock inputs to the DIMM. (Optional) a. In order to reduce DIMM PLL current, the clock inputs to the DIMM are turned off, resulting in High-Z clock inputs to both the SDRAMs and the registers. This must be done after the RESET deactivate time of the register (t (INACT) ). The deactivate time defines the time in which the clocks and the control and address Data Sheet 42 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Application Note signals must maintain valid levels after RESET low has been applied and is specified in the register and DIMM documentation. b. The system may release DIMM address and control inputs to High-Z. This can be done after the RESET deactivate time of the register. The deactivate time defines the time in which the clocks and the control and the address signals must maintain valid levels after RESET low has been applied. It is highly recommended that CKE continue to remain low during this operation. 4. The DIMM is in lowest power Self Refresh mode. Self Refresh Exit (RESET low, clocks powered off) -- Optional 1. Stabilization of Clocks to the SDRAM. The system must drive clocks to the application frequency (PLL operation is not assured until the input clock reaches ~20MHz). Stability of clocks at the SDRAMs will be affected by all applicable system clock devices, and time must be allotted to permit all clock devices to settle. Once a stable clock is received at the DIMM PLL, the required PLL stabilization time (assuming power to the DIMM is stable) is 100 microseconds. 2. The system applies valid logic levels to the data inputs of the register (address and controls at the DIMM connector). CKE must be maintained low and all other inputs should be driven to a known state. In general these commands can be determined by the system designer. One option is to apply an SDRAM `NOP' command (with CKE low), as this is the first command defined by the JEDEC Self Refresh Exit sequence (ideally this would be a `NOP Deselect' command). A second option is to apply low levels on all of the register inputs, to be consistent with the state of the register outputs. 3. The system switches RESET to a logic `high' level. The SDRAM is now functional and prepared to receive commands. Since the RESET signal is asynchronous, RESET timing relationship to a specific clock edge is not required (during this period, register inputs must remain stable). 4. The system must maintain stable register inputs until normal register operation is attained. The registers have an activation time that allows the clock receivers, input receivers, and output drivers sufficient time to be turned on and become stable. During this time the system must maintain the valid logic levels described in Step 2. It is also a functional requirement that the registers maintain a low state at the CKE outputs to guarantee that the DDR SDRAMs continue to receive a low level on CKE. Register activation time (t (ACT) ), from asynchronous switching of RESET from low to high until the registers are stable and ready to accept an input signal, is specified in the register and DIMM do-umentation. 5. System can begin the JEDEC-defined DDR SDRAM Self Refresh Exit Procedure. Self Refresh Entry (RESET low, clocks running) -- Optional Although keeping the clocks running increases power consumption from the on-DIMM PLL during self refresh, this is an alternate operating mode for these DIMMs. 1. System enters Self Refresh entry command. (CKE Low, CS Low, RAS Low, CAS Low, WE High) Note: Note: The commands reach the DDR SDRAM one clock later due to the additional register pipelining on a Registered DIMM. After this command is issued to the SDRAM, all of the address and control and clock input conditions to the SDRAM are Don't Cares -- with the exception of CKE. 2. The system sets RESET at a valid low level. This input condition forces all register outputs to a low state, independent of the condition on the data and clock register inputs, and ensures that CKE is a stable low-level at the DDR SDRAMs. 3. The system may release DIMM address and control inputs to High-Z. This can be done after the RESET deactivate time of the register (t (INACT) ). The deactivate time describes the time in which the clocks and the control and the address signals must maintain valid levels after RESET low has been applied. It is highly recommended that CKE continue to remain low during the operation. 4. The DIMM is in a low power, Self Refresh mode. Data Sheet 43 Rev. 0.5, 2003-12 HYS72D[128/256][300/320/321/500][GBR/HR]-[5/6/7/7F]-B Registered Double Data Rate SDRAM Module Application Note Self Refresh Exit (RESET low, clocks running) -- Optional 1. The system applies valid logic levels to the data inputs of the register (address and controls at the DIMM connector). CKE must be maintained low and all other inputs should be driven to a known state. In general these commands can be determined by the system designer. One option is to apply an SDRAM `NOP' command (with CKE low), as this is the first command defined by the Self Refresh Exit sequence (ideally this would be a `NOP Deselect' command). A second option is to apply low levels on all of the register inputs to be consistent with the state of the register outputs. 2. The system switches RESET to a logic 'high' level. The SDRAM is now functional and prepared to receive commands. Since the RESET signal is asynchronous, it does not need to be tied to a particular clock edge (during this period, register inputs must continue to remain stable). 3. The system must maintain stable register inputs until normal register operation is attained. The registers have an activation time that allows the clock receivers, input receivers, and output drivers sufficient time to be turned on and become stable. During this time the system must maintain the valid logic levels described in Step 1. It is also a functional requirement that the registers maintain a low state at the CKE outputs in order to guarantee that the DDR SDRAMs continue to receive a low level on CKE. This activation time, from asynchronous switching of RESET from low to high, until the registers are stable and ready to accept an input signal, is t (ACT ) as specified in the register and DIMM documentation. 4. The system can begin JEDEC defined DDR SDRAM Self Refresh Exit Procedure. Self Refresh Entry/Exit (RESET high, clocks running) -- Optional As this sequence does not involve the use of the RESET function, the JEDEC standard SDRAM specification explains in detail the method for entering and exiting Self Refresh for this case. Self Refresh Entry (RESET high, clocks powered off) -- Not Permissible In order to maintain a valid low level on the register output, it is required that either the clocks be running and the system drive a low level on CKE, or the clocks are powered off and RESET is asserted low according to the sequence defined in this application note. In the case where RESET remains high and the clocks are powered off, the PLL drives a High-Z clock input into the register clock input. Without the low level on RESET an unknown DIMM state will result. Data Sheet 44 Rev. 0.5, 2003-12 http://www.infineon.com Published by Infineon Technologies AG