LT1739 Dual 500mA, 200MHz xDSL Line Driver Amplifier U FEATURES DESCRIPTIO 3mm x 4mm High Power DFN Package Exceeds All Requirements For Full Rate, Downstream ADSL Line Drivers 500mA Minimum IOUT 11.1V Output Swing, VS = 12V, RL = 100 10.9V Output Swing, VS = 12V, IL = 250mA Low Distortion: - 82dBc at 1MHz, 2VP-P Into 50 Power Saving Adjustable Supply Current Power Enhanced TSSOP-20 Small Footprint Package 200MHz Gain Bandwidth 600V/s Slew Rate Specified at 12V and 5V The LT(R)1739 is a 500mA minimum output current, dual op amp with outstanding distortion performance. The amplifiers are gain-of-ten stable, but can be easily compensated for lower gains. The extended output swing allows for lower supply rails to reduce system power. Supply current is set with an external resistor to optimize power dissipation. The LT1739 features balanced, high impedance inputs with low input bias current and input offset voltage. Active termination is easily implemented for further system power reduction. Short-circuit protection and thermal shutdown insure the device's ruggedness. The outputs drive a 100 load to 11.1V with 12V supplies, and 10.9V with a 250mA load. The LT1739 is a pin-for-pin replacement for the LT1794 in xDSL line driver applications and requires no circuit changes. U APPLICATIO S High Density ADSL Central Office Line Drivers High Efficiency ADSL, HDSL2, G.lite, SHDSL Line Drivers Buffers Test Equipment Amplifiers Cable Drivers The LT1739 is available in the very small, thermally enhanced, 3mm x 4mm DFN package or a 20-lead TSSOP for maximum port density in central office line driver applications. For a dual version of the LT1739, see the LT6301 data sheet. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO High Efficiency 12V Supply ADSL Central Office Line Driver 12V + +IN 3mm x 4mm DFN Package Bottom View RBIAS 24.9k 1/2 LT1739 SHDN 12.7 EXPOSED THERMAL PAD - 1k 1:2* 0.8 mm * * 110 100 1000pF 110 1k 1739 TA01 173 3m m - 1/2 LT1739 -IN + 12.7 9T A0 2 m 4m *COILCRAFT X8390-A OR EQUIVALENT ISUPPLY = 10mA PER AMPLIFIER WITH RBIAS = 24.9k SHDNREF -12V 1739fas, sn1739 1 LT1739 U W W W ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage (V + to V -) ................................. 13.5V Input Current ..................................................... 10mA Output Short-Circuit Duration (Note 2) ........... Indefinite Operating Temperature Range ............... - 40C to 85C Specified Temperature Range (Note 3) .. - 40C to 85C Junction Temperature FE Package ....................................................... 150C UE Package ...................................................... 125C Storage Temperature Range FE Package ....................................... - 65C to 150C UE Package ...................................... - 65C to 125C Lead Temperature (Soldering, 10 sec).................. 300C W U U PACKAGE/ORDER INFORMATION TOP VIEW V- 1 20 V- NC 2 19 NC -IN 3 18 OUT +IN 4 17 V + SHDN 5 16 NC SHDNREF 6 15 NC V+ +IN 7 14 -IN 8 13 OUT NC 9 12 NC V - 10 11 V - ORDER PART NUMBER ORDER PART NUMBER TOP VIEW LT1739CFE LT1739IFE -IN A 1 12 V - +IN A 2 11 OUT A SHDN 3 10 V + SHDNREF 4 9 V+ +IN B 5 8 OUT B -IN B 6 7 V- LT1739CUE LT1739IUE UE PART MARKING UE12 PACKAGE 12-LEAD (4mm x 3mm) PLASTIC DFN 1739 1739I TJMAX = 125C, JA = 60C/W, JC = 3C/W (Note 4) UNDERSIDE METAL CONNECTED TO V - FE PACKAGE 20-LEAD PLASTIC TSSOP TJMAX = 150C, JA = 40C/W, JC = 3C/W (Note 4) UNDERSIDE METAL CONNECTED TO V - Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full specified temperature range, otherwise specifications are at TA = 25C. VCM = 0V, pulse tested, 5V VS 12V, VSHDNREF = 0V, RBIAS = 24.9k between V + and SHDN unless otherwise noted. (Note 3) SYMBOL PARAMETER VOS Input Offset Voltage CONDITIONS MIN TYP MAX 1 5.0 7.5 mV mV 0.3 5.0 7.5 mV mV Input Offset Voltage Matching Input Offset Voltage Drift IOS Input Offset Current Input Bias Current 500 800 nA nA 0.1 4 6 A A 100 500 800 nA nA Input Bias Current Matching V/C 10 100 IB UNITS en Input Noise Voltage Density f = 10kHz 8 nV/Hz in Input Noise Current Density f = 10kHz 0.8 pA/Hz 1739fas, sn1739 2 LT1739 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full specified temperature range, otherwise specifications are at TA = 25C. VCM = 0V, pulse tested, 5V VS 12V, VSHDNREF = 0V, RBIAS = 24.9k between V + and SHDN unless otherwise noted. (Note 3) SYMBOL PARAMETER RIN Input Resistance CIN Input Capacitance CMRR PSRR AVOL CONDITIONS (V + - VCM = 2V) to Differential (V -+ 2V) Input Voltage Range (Positive) Input Voltage Range (Negative) (Note 5) (Note 5) Common Mode Rejection Ratio VCM = (V + - 2V) to (V - + 2V) Power Supply Rejection Ratio Large-Signal Voltage Gain (Note 8) MIN TYP 5 50 6.5 M M 3 pF V+ - 2 V+ - 1 V- + 1 74 66 83 dB dB 74 66 88 dB dB 63 57 76 dB dB 60 54 70 dB dB 10.9 10.7 11.1 V V 10.6 10.4 10.9 V V 3.7 3.5 4.0 V V 3.6 3.4 3.9 V V VS = 4V to 12V VS = 12V, VOUT = 10V, RL = 40 VS = 5V, VOUT = 3V, RL = 25 VOUT Output Swing (Note 8) VS = 12V, RL = 100 VS = 12V, IL = 250mA VS = 5V, RL = 25 VS = 5V, IL = 250mA IOUT Maximum Output Current (Note 8) VS = 12V, RL = 1 500 1200 IS Supply Current per Amplifier VS = 12V, RBIAS = 24.9k (Note 6) 8.0 6.7 10 VS = 12V, RBIAS = 32.4k (Note 6) VS = 12V, RBIAS = 43.2k (Note 6) VS = 12V, RBIAS = 66.5k (Note 6) MAX 2.2 1.8 V V V- + 2 mA 13.5 15.0 mA mA mA mA mA 3.4 5.0 5.8 mA mA 8 6 4 VS = 5V, RBIAS = 24.9k (Note 6) UNITS Supply Current in Shutdown VSHDN = 0.4V 0.1 1 mA Output Leakage in Shutdown VSHDN = 0.4V 0.3 1 mA Channel Separation (Note 8) VS = 12V, VOUT = 10V, RL = 40 80 77 110 dB dB VS = 12V, AV = - 10, (Note 7) 300 600 V/s VS = 5V, AV = -10, (Note 7) 100 SR Slew Rate 200 V/s HD2 Differential 2nd Harmonic Distortion VS = 12V, AV = 10, 2VP-P, RL = 50, 1MHz - 85 dBc HD3 Differential 3rd Harmonic Distortion VS = 12V, AV = 10, 2VP-P, RL = 50, 1MHz - 82 dBc GBW Gain Bandwidth f = 1MHz 200 MHz Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: Applies to short circuits to ground only. A short circuit between the output and either supply may permanently damage the part when operated on supplies greater than 10V. Note 3: The LT1739C is guaranteed to meet specified performance from 0C to 85C and is designed, characterized and expected to meet these extended temperature limits, but is not tested at - 40C. The LT1739I is guaranteed to meet the extended temperature limits. Note 4: Thermal resistance varies depending upon the amount of PC board metal attached to the device and rate of air flow over the device. If the maximum dissipation of the package is exceeded, the device will go into thermal shutdown and be protected. Note 5: Guaranteed by the CMRR tests. Note 6: RBIAS is connected between V + and the SHDN pin, with the SHDNREF pin grounded. Note 7: Slew rate is measured at 5V on a 10V output signal while operating on 12V supplies and 1V on a 3V output signal while operating on 5V supplies. Note 8: This parameter of the LT1739CUE/LT1739IUE is 100% tested at room temperature, but is not tested at -40C, 0C or 85C. 1739fas, sn1739 3 LT1739 U W TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Ambient Temperature Input Common Mode Range vs Supply Voltage V+ 15 11 10 9 VS = 12V 180 IS PER AMPLIFIER = 10mA -1.0 160 -1.5 140 IBIAS (nA) 12 200 TA = 25C VOS > 1mV -0.5 COMMON MODE RANGE (V) -2.0 2.0 80 60 40 6 0.5 20 5 -50 V- -30 -10 10 30 50 TEMPERATURE (C) 70 90 2 4 8 10 6 SUPPLY VOLTAGE (V) 12 1 1 INPUT CURRENT NOISE (pA/Hz) 10 in V+ 760 740 720 700 SINKING 680 SOURCING 660 640 620 0.1 10 1 100 1k FREQUENCY (Hz) 600 -50 0.1 100k 10k -30 30 -10 10 50 TEMPERATURE (C) 1739 G04 120 45 100 80 40 -40 20 -80 GAIN 0 -20 -40 -60 -120 -160 TA = 25C VS = 12V AV = -10 RL = 100 IS PER AMPLIFIER = 10mA -80 100k 1M 10M FREQUENCY (Hz) 70 -200 100M 1739 G07 RL = 100 -1.0 ILOAD = 250mA -1.5 1.5 ILOAD = 250mA 1.0 RL = 100 0.5 V- - 50 -30 90 50 30 10 TEMPERATURE (C) -10 70 Slew Rate vs Supply Current 1000 TA = 25C VS = 12V AV = 10 RL = 100 35 900 800 30 25 20 15 10 -240 5 -280 0 90 1739 G06 SLEW RATE (V/s) 40 PHASE (DEG) 0 -3dB BANDWIDTH (MHz) 40 60 90 VS = 12V -0.5 -3dB Bandwidth vs Supply Current 120 80 70 1739 G05 Open-Loop Gain and Phase vs Frequency PHASE 10 30 50 -10 TEMPERATURE (C) Output Saturation Voltage vs Ambient Temperature VS = 12V IS PER AMPLIFIER = 10mA 780 en 10 800 100 TA = 25C VS = 12V IS PER AMPLIFIER = 10mA -30 1739 G03 Output Short-Circuit Current vs Ambient Temperature ISC (mA) 100 0 -50 14 1739 G02 Input Noise Spectral Density INPUT VOLTAGE NOISE (V/Hz) 100 1.0 1739 G01 GAIN (dB) 120 1.5 8 7 OUTPUT SATURATION VOLTAGE (V) ISUPPLY PER AMPLIFIER (mA) VS = 12V 14 RBIAS = 24.9k TO SHDN VSHDNREF = 0V 13 Input Bias Current vs Ambient Temperature 700 600 TA = 25C VS = 12V AV = -10 RL = 1k RISING FALLING 500 400 300 200 100 2 4 6 8 10 12 14 SUPPLY CURRENT PER AMPLIFIER (mA) 1739 G08 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SUPPLY CURRENT PER AMPLIFIER (mA) 1739 G09 1739fas, sn1739 4 LT1739 U W TYPICAL PERFOR A CE CHARACTERISTICS CMRR vs Frequency 80 70 60 50 40 30 20 100 10 0 0.1 1 10 FREQUENCY (MHz) 100 80 50 (-) SUPPLY 40 30 (+) SUPPLY 20 0 -15 -10 0.01 -20 0.1 1 10 FREQUENCY (MHz) 1k 100 10k 100k 1M 10M FREQUENCY (Hz) Supply Current vs VSHDN 35 TA = 25C VS = 12V VSHDNREF = 0V 1.5 1.0 0.5 100 0 100M 1739 G12 SUPPLY CURRENT PER AMPLIFIER (mA) ISHDN (mA) 1 10 FREQUENCY (MHz) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VSHDN (V) 1739 G13 TA = 25C VS = 12V VSHDNREF = 0V 30 25 20 15 10 5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VSHDN (V) 1739 G14 1739 G14 Differential Harmonic Distortion vs Frequency Differential Harmonic Distortion vs Output Amplitude -40 -40 f = 1MHz TA = 25C -50 VS = 12V AV = 10 RL = 50 -60 I PER AMPLIFIER = 10mA S -45 -50 DISTORTION (dBc) DISTORTION (dBc) OUTPUT IMPEDANCE () IS PER AMPLIFIER = 15mA 0.1 15mA PER AMPLIFIER 0 -5 10 2.0 IS PER AMPLIFIER = 2mA 0.01 0.01 5 ISHDN vs VSHDN TA = 25C VS 12V 0.1 10mA PER AMPLIFIER -10 2.5 IS PER AMPLIFIER = 10mA 2mA PER AMPLIFIER 10 1739 G11 100 1 20 15 60 Output Impedance vs Frequency 10 VS = 12V AV = 10 25 70 1739 G10 1000 30 VS = 12V AV = 10 IS = 10mA PER AMPLIFIER 90 GAIN (dB) TA = 25C VS = 12V IS = 10mA PER AMPLIFIER 90 POWER SUPPLY REJECTION (dB) COMMON MODE REJECTION RATIO (dB) 100 Frequency Response vs Supply Current PSRR vs Frequency HD3 -70 -80 HD2 -55 -60 VO = 10VP-P TA = 25C VS = 12V AV = 10 RL = 50 IS PER AMPLIFIER = 10mA -65 -70 -75 HD3 -80 -90 -85 -100 0 2 4 6 8 10 12 VOUT(P-P) 14 16 18 1739 G16 HD2 -90 100 200 300 400 500 600 700 800 900 1000 FREQUENCY (kHz) 1739 G17 1739fas, sn1739 5 LT1739 U W TYPICAL PERFOR A CE CHARACTERISTICS Differential Harmonic Distortion vs Supply Current -40 20 -50 OUTPUT VOLTAGE (VP-P) VO = 10VP-P VS = 12V AV = 10 RL = 50 -45 DISTORTION (dBc) Undistorted Output Swing vs Frequency -55 f = 1MHz, HD3 -60 -65 f = 100kHz, HD2 -70 -75 15 10 5 f = 100kHz, HD3 -80 f = 1MHz, HD2 -85 2 3 4 5 6 7 8 9 10 ISUPPLY PER AMPLIFIER (mA) SFDR > 40dB TA = 25C VS = 12V AV = 10 RL = 50 IS PER AMPLIFIER = 10mA 0 100k 11 300k 1M 3M FREQUENCY (Hz) 10M 1739 G19 1739 G18 TEST CIRCUIT SUPPLY BYPASSING 12V 0.1F V+ +IN A RBIAS + 0.1F 0.1F -12V 12.7 1k OUT (+) 110 OUT (-) 110 1:2* RL 50 SPLITTER MINICIRCUITS ZSC5-2-2 4.7F 4.7F OUT A - -12V 49.9 + VOUT(P-P) 10k EIN 4.7F + SHDN A -IN A 12V + 100 LINE LOAD 0.01F 1k 10k -IN B 12.7 - B +IN B + 1739 TC SHDNREF V- -12V OUT B *COILCRAFT X8390-A OR EQUIVALENT VOUTP-P AMPLITUDE SET AT EACH AMPLIFIER OUTPUT DISTORTION MEASURED ACROSS LINE LOAD 1739fas, sn1739 6 LT1739 U W U U APPLICATIO S I FOR ATIO The LT1739 is a high speed, 200MHz gain bandwidth product, dual voltage feedback amplifier with high output current drive capability, 500mA source and sink. The LT1739 is ideal for use as a line driver in xDSL data communication applications. The output voltage swing has been optimized to provide sufficient headroom when operating from 12V power supplies in full-rate ADSL applications. The LT1739 also allows for an adjustment of the operating current to minimize power consumption. In addition, the LT1739 is available in small footprint 3mm x 4mm DFN and 20-lead TSSOP surface mount package to minimize PCB area in multiport central office DSL cards. on supply current per amplifier with RBIAS connected between the SHDN pin and the 12V V + supply of the LT1739 and the approximate design equations. Figure 3 illustrates the same control with RBIAS connected between the SHDNREF pin and ground while the SHDN pin is tied to V +. Either approach is equally effective. SHDN 5I I TO START-UP CIRCUITRY Using a single external resistor, RBIAS, connected in one of two ways provides a much more predictable control of the quiescent supply current. Figure 2 illustrates the effect IBIAS TO AMPLIFIERS BIAS CIRCUITRY SHDNREF 1739 F01 IBIAS = 2 ISHDN = ISHDNREF 5 ISUPPLY PER AMPLIFIER (mA) = 64 * IBIAS Figure 1. Internal Current Biasing Circuitry Setting the Quiescent Operating Current ISUPPLY PER AMPLIFIER (mA) 30 VS = 12V V + = 12V 25 RBIAS SHDN 20 IS PER AMPLIFIER (mA) V + - 1.2V * 25.6 RBIAS + 2k 15 RBIAS = 10 V + - 1.2V * 25.6 - 2k IS PER AMPLIFIER (mA) SHDNREF 5 0 7 40 10 70 100 RBIAS (k) 130 160 190 1739 F02 Figure 2. RBIAS to V+ Current Control 45 VS = 12V V + = 12V 40 ISUPPLY PER AMPLIFIER (mA) The internal biasing circuitry is shown in Figure 1. Grounding the SHDNREF pin and directly driving the SHDN pin with a voltage can control the operating current as seen in the Typical Performance Characteristics. When the SHDN pin is less than SHDNREF + 0.4V, the driver is shut down and consumes typically only 100A of supply current and the outputs are in a high impedance state. Part to part variations, however, will cause inconsistent control of the quiescent current if direct voltage drive of the SHDN pin is used. 2I 2I 1k To minimize signal distortion, the LT1739 amplifiers are decompensated to provide very high open-loop gain at high frequency. As a result each amplifier is frequency stable with a closed-loop gain of 10 or more. If a closedloop gain of less than 10 is desired, external frequency compensating components can be used. Power consumption and dissipation are critical concerns in multiport xDSL applications. Two pins, Shutdown (SHDN) and Shutdown Reference (SHDNREF), are provided to control quiescent power consumption and allow for the complete shutdown of the driver. The quiescent current should be set high enough to prevent distortion induced errors in a particular application, but not so high that power is wasted in the driver unnecessarily. A good starting point to evaluate the LT1739 is to set the quiescent current to 10mA per amplifier. 2k SHDN 35 V + - 1.2V * 64 IS PER AMPLIFIER (mA) RBIAS + 5k 30 25 RBIAS = 20 V + - 1.2V * 64 - 5k IS PER AMPLIFIER (mA) SHDNREF 15 RBIAS 10 5 0 4 7 10 30 50 70 90 100 130 150 170 190 210 230 250 270 290 RBIAS (k) 1739 F03 Figure 3. RBIAS to Ground Current Control 1739fas, sn1739 7 LT1739 U W U U APPLICATIO S I FOR ATIO Logic Controlled Operating Current The DSP controller in a typical xDSL application can have I/O pins assigned to provide logic control of the LT1739 line driver operating current. As shown in Figure 4 one or two logic control inputs can set two or four different operating modes. The logic inputs add or subtract current to the SHDN input to set the operating current. The one logic input example selects the supply current to be either full power, 10mA per amplifier or just 2mA per amplifier, which significantly reduces the driver power consumption while maintaining less than 2 output impedance to frequencies less than 1MHz. This low power mode retains termination impedance at the amplifier outputs and the line driving back termination resistors. With this termination, while a DSL port is not transmitting data, it can still sense a received signal from the line across the backtermination resistors and respond accordingly. The two logic input control provides two intermediate (approximately 7mA per amplifier and 5mA per amplifier) operating levels between full power and termination modes. For proper operation of the current control circuitry, it is necessary that the SHDNREF pin be biased at least 2V more positive than V -. In single supply applications where V - is at ground potential, special attention to the DC bias of the SHDNREF pin is required. Contact Linear Technology for assistance in implementing a single supply design with operating current control. These modes can be useful for overall system power management when full power transmissions are not necessary. Shutdown and Recovery The ultimate power saving action on a completely idle port is to fully shut down the line driver by pulling the SHDN pin to within 0.4V of the SHDNREF potential. As shown in Figure 5 complete shutdown occurs in less than 10s and, more importantly, complete recovery from the shut down state to full operation occurs in less than 2s. The biasing circuitry in the LT1739 reacts very quickly to bring the amplifiers back to normal operation. VSHDN SHDNREF = 0V AMPLIFIER OUTPUT 1794 F05 Figure 5. Shutdown and Recovery Timing 12V OR VLOGIC Two Control Inputs VC1 H H L L RESISTOR VALUES (k) RSHDN TO VCC (12V) RSHDN TO VLOGIC VLOGIC 3V 3.3V 5V 3V 3.3V 5V RSHDN 40.2 43.2 60.4 4.99 6.81 19.6 11.5 13.0 21.5 8.66 10.7 20.5 RC1 19.1 22.1 36.5 14.3 17.8 34.0 RCO VC0 SUPPLY CURRENT PER AMPLIFIER (mA) H 10 10 10 10 10 10 L 7 7 7 7 7 7 H 5 5 5 5 5 5 L 2 2 2 2 2 2 VLOGIC VC1 0V VC0 RC1 SHDN RC0 2k SHDNREF One Control Input 12V OR VLOGIC RESISTOR VALUES (k) RSHDN TO VCC (12V) RSHDN TO VLOGIC VLOGIC 3V 3.3V 5V 3V 3.3V 5V RSHDN 40.2 43.2 60.4 4.99 6.81 19.6 RC 7.32 8.25 13.7 5.49 6.65 12.7 VC H L RSHDN VLOGIC 0V VC RC RSHDN SHDN 2k SUPPLY CURRENT PER AMPLIFIER (mA) 10 10 10 10 10 10 2 2 2 2 2 2 1739 F04 SHDNREF Figure 4. Providing Logic Input Control of Operating Current Power Dissipation and Heat Management xDSL applications require the line driver to dissipate a significant amount of power and heat compared to other components in the system. The large peak to RMS variations of DMT and CAP ADSL signals require high supply voltages to prevent clipping, and the use of a step-up transformer to couple the signal to the telephone line can require high peak current levels. These requirements result in the driver package having to dissipate significant amounts of power. Several multiport cards inserted into a rack in an enclosed central office box can add up to many, many watts of power dissipation in an elevated ambient temperature environment. The LT1739 has builtin thermal shutdown circuitry that will protect the amplifiers if operated at excessive temperatures, however data transmissions will be seriously impaired. It is important in 1739fas, sn1739 8 LT1739 U W U U APPLICATIO S I FOR ATIO the design of the PCB and card enclosure to take measures to spread the heat developed in the driver away to the ambient environment to prevent thermal shutdown (which occurs when the junction temperature of the LT1739 exceeds 165C). Estimating Line Driver Power Dissipation Figure 6 is a typical ADSL application shown for the purpose of estimating the power dissipation in the line driver. Due to the complex nature of the DMT signal, which looks very much like noise, it is easiest to use the RMS values of voltages and currents for estimating the driver power dissipation. The voltage and current levels shown for this example are for a full-rate ADSL signal driving 20dBm or 100mWRMS of power on to the 100 telephone line and assuming a 0.5dBm insertion loss in the transformer. The quiescent current for the LT1739 is set to 10mA per amplifier. The power dissipated in the LT1739 is a combination of the quiescent power and the output stage power when driving a signal. The two amplifiers are configured to place a differential signal on to the line. The Class AB output stage in each amplifier will simultaneously dissipate power in the upper power transistor of one amplifier, while sourcing current, and the lower power transistor of the other amplifier, while sinking current. The total device power dissipation is then: PD = PQUIESCENT + PQ(UPPER) + PQ(LOWER) PD = (V+ - V-) * IQ + (V+ - VOUTARMS) * ILOAD + (V - - VOUTBRMS) * ILOAD With no signal being placed on the line and the amplifier biased for 10mA per amplifier supply current, the quiescent driver power dissipation is: PDQ = 24V * 20mA = 480mW This can be reduced in many applications by operating with a lower quiescent current value. When driving a load, a large percentage of the amplifier quiescent current is diverted to the output stage and becomes part of the load current. Figure 7 illustrates the total amount of biasing current flowing between the + and - power supplies through the amplifiers as a function of load current. As much as 60% of the quiescent no load operating current is diverted to the load. 12V 24.9k - SETS IQ PER AMPLIFIER = 10mA 20mA DC 2VRMS SHDN 17.4 + +IN A - 1k 1:1.7 * * 110 ILOAD = 57mARMS 1000pF 110 3.16VRMS 1k - 17.4 1739 F06 B -IN 100 SHDNREF + -12V -2VRMS Figure 6. Estimating Line Driver Power Dissipation 1739fas, sn1739 9 LT1739 U W U U APPLICATIO S I FOR ATIO compact circuit layout to allow more ports to be implemented on any given size PCB. 25 TOTAL IQ (mA) 20 15 10 5 0 -240 -200 -160 -120 -80 -40 0 40 ILOAD (mA) 80 120 160 200 240 1739 F07 Figure 7. IQ vs ILOAD At full power to the line the driver power dissipation is: PD(FULL) = 24V * 8mA + (12V - 2VRMS) * 57mARMS + [|-12V - (- 2VRMS)|] * 57mARMS PD(FULL) = 192mW + 570mW + 570mW = 1.332W* The junction temperature of the driver must be kept less than the thermal shutdown temperature when processing a signal. The junction temperature is determined from the following expression: TJ = TAMBIENT (C) + PD(FULL) (W) * JA (C/W) JA is the thermal resistance from the junction of the LT1739 to the ambient air, which can be minimized by heat-spreading PCB metal and airflow through the enclosure as required. For the example given, assuming a maximum ambient temperature of 85C and keeping the junction temperature of the LT1739 to 140C maximum, the maximum thermal resistance from junction to ambient required is: JA(MAX) = 140C - 85C = 41.3C / W 1.332W Heat Sinking Using PCB Metal Designing a thermal management system is often a trial and error process as it is never certain how effective it is until it is manufactured and evaluated. As a general rule, the more copper area of a PCB used for spreading heat away from the driver package, the more the operating junction temperature of the driver will be reduced. The limit to this approach however is the need for very Fortunately xDSL circuit boards use multiple layers of metal for interconnection of components. Areas of metal beneath the LT1739 connected together through several small 13 mil vias can be effective in conducting heat away from the driver package. The use of inner layer metal can free up top and bottom layer PCB area for external component placement. Figure 8 shows examples of PCB metal being used for heat spreading. These are provided as a reference for what might be expected when using different combinations of metal area on different layers of a PCB. These examples are with a 4-layer board using 1oz copper on each. The most effective layers for spreading heat are those closest to the LT1739 junction. The small TSSOP and DFN packages are very effective for compact line driver designs. Both packages also have an exposed metal heat sinking pad on the bottom side which, when soldered to the PCB top layer metal, directly conducts heat away from the IC junction. Soldering the thermal pad to the board produces a thermal resistance from junction to case, JC, of approximately 3C/W. As a minimum, the area directly beneath the package on all PCB layers can be used for heat spreading. Limiting the area of metal to just that of the exposed metal heat sinking pad however is not very effective, particularly if the amplifiers are required to dissipate significant power levels. This is shown in Figure 8 for both the TSSOP and DFN packages. Expanding the area of metal on various layers significantly reduces the overall thermal resistance. If possible, an entire unbroken plane of metal close to the heat sinking pad is best for multiple drivers on one PCB card. The addition of vias (small 13mil or smaller holes which fill during PCB plating) connecting all layers of heat spreading metal also helps to reduce operating temperatures of the driver. These too are shown in Figure 8. Important Note: The metal planes used for heat sinking the LT1739 are electrically connected to the negative supply potential of the driver, typically - 12V. These planes must be isolated from any other power planes used in the board design. *Note: Design techniques exist to significantly reduce this value. (See Line Driving Back Termination) 1739fas, sn1739 10 LT1739 U W U U APPLICATIO S I FOR ATIO When PCB cards containing multiple ports are inserted into a rack in an enclosed cabinet, it is often necessary to provide airflow through the cabinet and over the cards. As STILL AIR JA PACKAGE TOP LAYER seen in the graph of Figure 8, this is also very effective in further reducing the junction-to-ambient thermal resistance of each line driver. 2ND LAYER 3RD LAYER BOTTOM LAYER TSSOP 100C/W TSSOP 50C/W TSSOP 45C/W DFN 130C/W DFN 75C/W 1739 F08a Typical Reduction in JA with Laminar Airflow Over the Device 0 % REDUCTION RELATIVE TO JA IN STILL AIR REDUCTION IN JA (%) -10 -20 -30 -40 -50 -60 0 100 200 300 400 500 600 700 800 900 1000 AIRFLOW (LINEAR FEET PER MINUTE, lfpm) 1739 F08b Figure 8. Examples of PCB Metal Used for Heat Dissipation. Driver Package Mounted on Top Layer. Heat Sink Pad Soldered to Top Layer Metal. Metal Areas Drawn to Scale of Package Size 1739fas, sn1739 11 LT1739 U W U U APPLICATIO S I FOR ATIO Layout and Passive Components With a gain bandwidth product of 200MHz the LT1739 requires attention to detail in order to extract maximum performance. Use a ground plane, short lead lengths and a combination of RF-quality supply bypass capacitors (i.e., 0.1F). As the primary applications have high drive current, use low ESR supply bypass capacitors (1F to 10F). The parallel combination of the feedback resistor and gain setting resistor on the inverting input can combine with the input capacitance to form a pole that can cause frequency peaking. In general, use feedback resistors of 1k or less. Compensation The LT1739 is stable in a gain 10 or higher for any supply and resistive load. It is easily compensated for lower gains with a single resistor or a resistor plus a capacitor. Figure 9 shows that for inverting gains, a resistor from the inverting node to AC ground guarantees stability if the parallel combination of RC and RG is less than or equal to RF/9. For lowest distortion and DC output offset, a series capacitor, CC, can be used to reduce the noise gain at lower frequencies. The break frequency produced by R C and CC should be less than 5MHz to minimize peaking. Figure 10 shows compensation in the noninverting configuration. The RC, CC network acts similarly to the inverting case. The input impedance is not reduced because the network is bootstrapped. This network can also be placed between the inverting input and an AC ground. Another compensation scheme for noninverting circuits is shown in Figure 11. The circuit is unity gain at low frequency and a gain of 1 + RF/RG at high frequency. The DC output offset is reduced by a factor of ten. The techniques of Figures 10 and 11 can be combined as shown in Figure 12. The gain is unity at low frequencies, 1 + RF/RG at mid-band and for stability, a gain of 10 or greater at high frequencies. RF RG - VI RC VO + CC (OPTIONAL) RC VO -RF = RG VI RF VO =1+ VI RG + VI VO - CC (OPTIONAL) 1 < 5MHz 2RCCC RF (RC || RG) RF/9 1 < 5MHz 2RCCC (RC || RG) RF/9 RG 1739 F09 1739 F10 Figure 9. Compensation for Inverting Gains + Vi VO - RF RG Figure 10. Compensation for Noninverting Gains VO = 1 (LOW FREQUENCIES) VI R = 1 + F (HIGH FREQUENCIES) RG + VI RC VO - CC RG RF/9 RF 1 < 5MHz 2RGCC RG CBIG CC 1739 F11 Figure 11. Alternate Noninverting Compensation VO = 1 AT LOW FREQUENCIES VI R = 1 + F AT MEDIUM FREQUENCIES RG =1+ RF AT HIGH FREQUENCIES (RC || RG) 1739 F12 Figure 12. Combination Compensation 1739fas, sn1739 12 LT1739 U W U U APPLICATIO S I FOR ATIO In differential driver applications, as shown on the first page of this data sheet, it is recommended that the gain setting resistor be comprised of two equal value resistors connected to a good AC ground at high frequencies. This ensures that the feedback factor of each amplifier remains less than 0.1 at any frequency. The midpoint of the resistors can be directly connected to ground, with the resulting DC gain to the VOS of the amplifiers, or just bypassed to ground with a 1000pF or larger capacitor. Line Driving Back-Termination The standard method of cable or line back-termination is shown in Figure 13. The cable/line is terminated in its characteristic impedance (50, 75, 100, 135, etc.). A back-termination resistor also equal to the chararacteristic impedance should be used for maximum pulse fidelity of outgoing signals, and to terminate the line for incoming signals in a full-duplex application. There are three main drawbacks to this approach. First, the power dissipated in the load and back-termination resistors is equal so half of the power delivered by the amplifier is wasted in the termination resistor. Second, the signal is halved so the gain of the amplifer must be doubled to have the same overall gain to the load. The increase in gain increases noise and decreases bandwidth (which can also increase distortion). Third, the output swing of the amplifier is doubled which can limit the power it can deliver to the load for a given power supply voltage. An alternate method of back-termination is shown in Figure 14. Positive feedback increases the effective backtermination resistance so RBT can be reduced by a factor of n. To analyze this circuit, first ground the input. As RBT = RL/n, and assuming RP2>>RL we require that: VA = VO (1 - 1/n) to increase the effective value of RBT by n. VP = VO (1 - 1/n)/(1 + RF/RG) VO = VP (1 + RP2/RP1) Eliminating VP, we get the following: (1 + RP2/RP1) = (1 + RF/RG)/(1 - 1/n) For example, reducing RBT by a factor of n = 4, and with an amplifer gain of (1 + RF/RG) = 10 requires that RP2/RP1 = 12.3. Note that the overall gain is increased: RP2 / (RP2 + RP1) VO = VI (1+ 1/n) / (1+ RF /RG ) - RP1/(RP2 + RP1) [ VI ] [ ] CABLE OR LINE WITH CHARACTERISTIC IMPEDANCE RL + RBT VO - RL RF 1739 F13 RBT = RL VO 1 = (1 + RF/RG) VI 2 RG Figure 13. Standard Cable/Line Back Termination RP2 RP1 VI + VA RBT VP - VO RL RF RG 1739 F14 FOR RBT = ( )( 1+ RL n ) 1 RP1 RF =1- n RG RP1 + RP2 RP2/(RP2 + RP1) VO = VI 1 + 1/n ( ) 1+ RF RG - RP1 RP2 + RP1 Figure 14. Back Termination Using Postive Feedback 1739fas, sn1739 13 LT1739 U W U U APPLICATIO S I FOR ATIO + VI VA RBT VO - FOR RBT = RF 1 RF RP n= RG 1- RL RP RP RG VO = VI RL RF RL n R R 1+ F + F RG RP ( ) 2 1- - RF RP RBT -VI + -VA -VO 1739 F15 Figure 15. Back Termination Using Differential Postive Feedback A simpler method of using positive feedback to reduce the back-termination is shown in Figure 15. In this case, the drivers are driven differentially and provide complementary outputs. Grounding the inputs, we see there is inverting gain of -RF/RP from -VO to VA VA = VO (RF/RP) and assuming RP >> RL, we require VA = VO (1 - 1/n) solving RF/RP = 1 - 1/n So to reduce the back-termination by a factor of 3 choose RF/RP = 2/3. Note that the overall gain is increased to: VO/VI = (1 + RF/RG + RF/RP)/[2(1 - RF/RP)] Using positive feedback is often referred to as active termination. Figure 18 shows a full-rate ADSL line driver incorporating positive feedback to reduce the power lost in the back termination resistors by 40% yet still maintains the proper impedance match to the100 characteristic line impedance. This circuit also reduces the transformer turns ratio over the standard line driving approach resulting in lower peak current requirements. With lower current and less power loss in the back termination resistors, this driver dissipates only 1W of power, a 30% reduction. (Additional power savings are possible by further reducing the termination resistors' value). While the power savings of positive feedback are attractive there is one important system consideration to be addressed, received signal sensitivity. The signal received from the line is sensed across the back termination resistors. With positive feedback, signals are present on both ends of the RBT resistors, reducing the sensed amplitude. Extra gain may be required in the receive channel to compensate, or a completely separate receive path may be implemented through a separate line coupling transformer. A demo board, DC306A-C, is available for the LT1739CFE. This demo board is a complete line driver with an LT1361 receiver included. It allows the evaluation of both standard and active termination approaches. It also has circuitry built in to evaluate the effects of operating with reduced supply current. The schematic of this demo board is shown in Figure 17. Considerations for Fault Protection The basic line driver design, shown on the front page of this data sheet, presents a direct DC path between the outputs of the two amplifiers. An imbalance in the DC biasing potentials at the noninverting inputs through either a fault condition or during turn-on of the system can create a DC voltage differential between the two amplifier outputs. This condition can force a considerable amount of current to flow as it is limited only by the small valued back-termination resistors and the DC resistance of the transformer primary. This high current can possibly cause the power supply voltage source to drop significantly impacting overall system performance. If left unchecked, the high DC current can heat the LT1739 to thermal shutdown. 1739fas, sn1739 14 LT1739 U W U U APPLICATIO S I FOR ATIO Using DC blocking capacitors, as shown in Figure 16, to AC couple the signal to the transformer eliminates the possibility for DC current to flow under any conditions. These capacitors should be sized large enough to not impair the frequency response characteristics required for the data transmission. Another important fault related concern has to do with very fast high voltage transients appearing on the telephone line (lightning strikes for example). TransZorbs(R), varistors and other transient protection devices are often used to absorb the transient energy, but in doing so also create fast voltage transitions themselves that can be coupled through the transformer to the outputs of the line driver. Several hundred volt transient signals can appear at the primary windings of the transformer with current into the driver outputs limited only by the back termination resistors. While the LT1739 has clamps to the supply rails at the output pins, they may not be large enough to handle the significant transient energy. External clamping diodes, such as BAV99s, at each end of the transformer primary help to shunt this destructive transient energy away from the amplifier outputs. TransZorb is a registered trademark of General Instruments, GSI 12V 12V -12V 24.9k + +IN BAV99 0.1F 1/2 LT1739 SHDN 12.7 - 1k 1:2 * * 110 LINE LOAD 1000pF 110 1k - 0.1F 1/2 LT1739 -IN + -12V 12.7 SHDNREF BAV99 12V -12V 1739 F16 Figure 16. Protecting the Driver Against Load Faults and Line Transients 1739fas, sn1739 15 LT1739 U W U U APPLICATIO S I FOR ATIO C1 0.1F 4 E2 DRV (+) R2 10k VCC U2A LT1739CFE R23 OPT 3 2 R5 OPT JP6 C16 1000pF 7 E8 DRV (-) 8 R26 OPT C17 OPT JP1 3 E5 LINE (-) COILCRAFT X8504-A C12 0.1F 100V C18 OPT 1206 R6 2.49k PLACE C4 AND C5 AS CLOSE TO U2 AS POSSIBLE R7 1k + U2B LT1739CFE 13 3 2 9 12 VEE 5 E10 ON/OFF 1 R13 10k 6 3 E11 VC0NTROL R18 10k 2 + VDD ON 1 U4B LT1541CS8 - R10 1k ON/OFF 2 3 JP3 ADJ 2 3 U4A LT1541CS8 - 1 1 JP4 Q1 FMMT3904 2 R20 9.31k VBIAS E13 RCVIN (-) 8 U3A LT1361CS8 - R19 1k 5 3 2 JP5 C11 1F 25V 3216 E3 GND E6 VEE 1 E9 RCV (+) VEE C14 0.1F R16 1k 6 R17 21.5k + E1 VCC 4 R15 OPT FIXED 1 C7 1F 25V 3216 + R12 1k R14 1.6k 4 + 2 R11 1.6k 7 + C3 1F 25V 3216 C13 VCC 0.1F 3 8 C10 0.1F 2 6 - JP2 C6 0.1F C4 0.1F 25V 0603 E7 RCVIN (+) R8 15.4 1/2W 2010 LT1121CST-5 SOT233 1 OUT IN GND C2 + 2 1F 25V 3216 C5 10F 35V 7343 + 19 R9 10k + 2 6 R3 1k U1 3 R4 2.49k R24 107 R25 107 1 5V VDD 8 VEE 3 7 1 1 R21 10k R22 10k 2 E4 LINE (+) 4 20 11 10 1 C15 OPT 17 18 5 - C9 0.1F VCC R1 15.4 1/2W 2010 14 + C8 0.1F 100V 10 - U3B LT1361CS8 7 E12 RCV (-) + 1 VBIAS 1739 SD Figure 17. LT1739, LT1361 ADSL Demo Board (DC306A-C) 1739fas, sn1739 16 LT1739 W W SI PLIFIED SCHE ATIC (one amplifier shown) V+ Q9 Q10 Q13 Q17 Q3 -IN Q1 Q7 C1 R1 Q6 Q2 Q5 +IN C2 Q4 Q14 OUT Q15 Q8 Q18 Q16 Q12 Q11 V- 1739 SS 1739fas, sn1739 17 LT1739 U PACKAGE DESCRIPTIO FE Package 20-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663) Exposed Pad Variation CA 6.40 - 6.60* (.252 - .260) 4.95 (.195) 4.95 (.195) 20 1918 17 16 15 14 13 12 11 6.60 0.10 2.74 (.108) 4.50 0.10 2.74 6.40 (.108) BSC SEE NOTE 4 0.45 0.05 1.05 0.10 0.65 BSC 1 2 3 4 5 6 7 8 9 10 RECOMMENDED SOLDER PAD LAYOUT 1.20 (.047) MAX 4.30 - 4.50* (.169 - .177) 0 - 8 0.09 - 0.20 (.0036 - .0079) 0.45 - 0.75 (.018 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 0.65 (.0256) BSC 0.195 - 0.30 (.0077 - .0118) 0.05 - 0.15 (.002 - .006) FE20 (CA) TSSOP 0203 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 1739fas, sn1739 18 LT1739 U PACKAGE DESCRIPTIO UE12 Package 12-Lead Plastic DFN (3mm x 4mm) (Reference LTC DWG # 05-08-1695) 0.58 0.05 3.40 0.05 1.70 0.05 2.24 0.05 (2 SIDES) 0.23 0.05 3.30 0.05 (2 SIDES) 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 4.00 0.10 (2 SIDES) 7 R = 0.115 TYP 0.38 0.10 12 R = 0.20 TYP 3.00 0.10 (2 SIDES) 1.70 0.10 (2 SIDES) PIN 1 TOP MARK PIN 1 NOTCH (UE12) DFN 0102 0.200 REF 0.75 0.05 0.00 - 0.05 6 0.23 0.05 3.30 0.10 (2 SIDES) 1 0.50 BSC BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE IS A VARIATION OF VERSION (WGED) IN JEDEC PACKAGE OUTLINE M0-229 2. ALL DIMENSIONS ARE IN MILLIMETERS 3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 4. EXPOSED PAD SHALL BE SOLDER PLATED 1739fas, sn1739 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LT1739 U TYPICAL APPLICATIO 12V 24.9k + +IN SHDN 1/2 LT1739 13.7 - 1k 1:1.2* 1.65k * * 182 100 LINE 1.65k 1000pF 182 1k - 1/2 LT1739 -IN + 13.7 *COILCRAFT X8502-A OR EQUIVALENT 1W DRIVER POWER DISSIPATION 1.15W POWER CONSUMPTION SHDNREF 1739 F17 -12V Figure 18. ADSL Line Driver Using Active Termination RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1361 Dual 50MHz, 800V/s Op Amp 15V Operation, 1mV VOS, 1A IB LT1794 Dual 500mA, 200MHz xDSL Line Driver ADSL CO Driver, Extended Output Swing, Low Power LT1795 Dual 500mA, 50MHz Current Feedback Amplifier Shutdown/Current Set Function, ADSL CO Driver LT1813 Dual 100MHz, 750V/s, 8nV/Hz Op Amp Low Noise, Low Power Differential Receiver, 4mA/Amplifier LT1886 Dual 200mA, 700MHz Op Amp 12V Operation, 7mA/Amplifier, ADSL Modem Line Driver LT1969 Dual 200mA, 700MHz Op Amp with Power Control 12V Operation, MSOP Package, ADSL Modem Line Driver LT6300 Dual 500mA, 200MHz xDSL Line Driver ADSL CO Driver in SSOP Package 1739fas, sn1739 20 Linear Technology Corporation LT/TP 0602 1.5K REV A * PRINTED IN THE USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2001