Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 General Description Features The AP4303 is a monolithic IC that contains quad operational amplifiers and a precision shunt regulator, 1.25Vfor AP4303-C or 1.24V for AP4303-D respectively. It is specifically designed to regulate the output current and voltage levels of switching battery chargers and power supplies. Op Amp * Input Offset Voltage: 0.5mV * Supply Current: 250A per Op Amp at 5.0V Supply Voltage * Unity Gain Bandwidth: 1MHz * Output Voltage Swing: 0 to (VCC - 1.5)V * The four Op Amps feature accurate voltage and current control. Combining a stable voltage reference with the four Op Amps makes AP4303 ideal for use in multifunction charger, power supply voltage monitor, signal processing and control system. Power Supply Range: 3 to 18V Voltage Reference * Reference Voltage Tolerance: 0.5%, 1% * Sink Current Capability from 0.1 to 80mA * Output Dynamic Impedance: 0.2 * Externally Adjusted Output Voltage Reference: 1.25V for AP4303-C and 1.24V for AP4303-D The IC offers the power converter designer a control solution that features increased precision with a corresponding reduction in system complexity and cost. The AP4303 is available in standard packages of DIP16 and SOIC-16. Applications * * Battery Charger Switching Power Supply DIP-16 SOIC-16 Figure 1. Package Types of AP4303 BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 1 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Pin Configuration M Package/P Package (SOIC-16/DIP-16) OUTPUT 1 1 16 OUTPUT 4 INPUT 1- 2 15 INPUT 4- INPUT 1+ 3 14 INPUT 4+ VCC 4 13 GND INPUT 2+ 5 12 INPUT 3+ INPUT 2- 6 11 INPUT 3- OUTPUT 2 7 10 OUTPUT 3 VREF 8 9 CATHODE Top View Figure 2. Pin configuration of AP4303 Functional Block Diagram OUTPUT 1 1 INPUT 1- 2 - + + 16 OUTPUT 4 15 INPUT 4- INPUT 4+ - INPUT 1+ 3 14 VCC 4 13 INPUT 2+ 5 12 INPUT 2- 6 OUTPUT 2 VREF - + + GND INPUT 3+ 11 INPUT 3- 7 10 OUTPUT 3 8 9 CATHODE Figure 3. Functional Block Diagram of AP4303 BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 2 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Functional Block Diagram (Continued) VCC 6A 4A 100A Q5 Q6 Q2 INPUT- Q3 Cc Q7 Q4 Q1 Rsc OUTPUT INPUT+ Q11 Q10 Q8 Q9 Q13 Q12 50uA Figure 4. Op Amp Functional Block Diagram (Each Amplifier) CATHODE 20A 20A VREF GND Figure 5. Voltage Reference Functional Block Diagram BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 3 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Ordering Information AP4303 E1: Lead Free Blank: Tin Lead Circuit Type TR: Tape and Reel Blank: Tube Voltage Tolerance A: 0.5% B: 1% Package M: SOIC-16 P: DIP-16 Package Reference Voltage Voltage Tolerance 1.25V DIP-16 1.24V Temperature Range 0.5% 1% Output Voltage Reference C: 1.25V D: 1.24V Part Number Marking ID Tin Lead Lead Free AP4303AP-C AP4303AP-CE1 Tin Lead Lead Free AP4303AP-C AP4303AP-CE1 AP4303BP-C AP4303BP-CE1 AP4303BP-C AP4303BP-CE1 0.5% AP4303AP-D AP4303AP-DE1 AP4303AP-D AP4303AP-DE1 1% AP4303BP-D AP4303BP-DE1 AP4303BP-D AP4303BP-DE1 AP4303AM-C AP4303AM-CE1 AP4303AM-C AP4303AM-CE1 -40 to 85oC 0.5% AP4303AM-CTR AP4303AM-CTRE1 AP4303AM-C AP4303AM-CE1 1.25V AP4303BM-C 1% -40 to 85oC SOIC-16 AP4303BM-CE1 AP4303BM-CTR AP4303BM-CTRE1 AP4303BM-C AP4303BM-CE1 AP4303AM-D 0.5% 1.24V AP4303AM-DE1 AP4303AM-D AP4303AM-DE1 AP4303AM-DTR AP4303AM-DTRE1 AP4303AM-D AP4303AM-DE1 AP4303BM-D 1% AP4303BM-C AP4303BM-CE1 AP4303BM-DE1 AP4303BM-D AP4303BM-DE1 AP4303BM-DTR AP4303BM-DTRE1 AP4303BM-D AP4303BM-DE1 Packing Type Tube Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant. BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 4 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Absolute Maximum Ratings (Note 1) Parameter Symbol Value Unit Power Supply Voltage (VCC to GND) VCC 20 V Op Amp Input Voltage Range VIN -0.3 to VCC + 0.3 V Op Amp Input Differentials Voltage VID 20 V Voltage Reference Cathode Current (Pin 9) IK 100 mA Power Dissipation PD 1000 mW DIP-16 SOIC-16 1000 Storage Temperature Range TSTG o -65 to 150 ESD Protection Voltage (Machine Model) >200 C V Note 1: Stresses greater than those listed under "Absolute Maximum Ratings " may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings " for extended periods may affect device reliability. Recommended Operating Conditions Parameter Supply Voltage Ambient Temperature Min Max Unit 3 18 V -40 85 o C BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 5 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Electrical Characteristics Operating Conditions: VCC = +5V, TA= 25oC unless otherwise specified. Parameter Conditions Min Total Supply Current, Excluding V = 5V, no load, -40oC T 85oC CC A Current in Voltage Reference VCC = 18V, no load, -40oC TA 85oC Typ Max Unit 1.0 1.6 mA 1.2 2.4 1.250 1.256 Voltage Reference Section Reference Voltage for AZ4303C IKA= 10mA TA = Reference Voltage for AZ4303D 25oC IKA = 10mA TA = 25oC 0.5% tolerance 1.244 1% tolerance 1.237 0.5% tolerance 1.234 1% tolerance 1.227 Reference Current 1.240 1.246 V 1.252 17 mV 0.1 0.2 mA VREF ~ 10V 1.0 2.7 mV/V 10V ~ 18V 0.5 2.0 0.7 4 A 0.4 1.2 A - Ratio of Change in VREF to that of IKA = 10mA Cathode Voltage 1.263 5 Reference Voltage Deviation over I = 10mA, T = -40 to 85oC KA A Full Temperature Range Minimum Cathode Current for Regulation V IKA = 10mA, R1 = 10K, R2 = The Deviation of Reference Current VKA = VREF, IKA = 10mA, over Temperature TA = -40oC to 85oC Off-State Cathode Current VREF = 0, VKA = 18V 0.05 1.0 A Dynamic Impedance IKA = 1.0 to 80mA, f<1kHz 0.2 0.5 0.5 3 mV Op Amp Section (per OPA) (VCC = 5V, VO = 1.4V, TA = 25oC, Unless otherwise noted) Input Offset Voltage TA = 25oC TA = -40 to 85oC 5 Input Offset Voltage Temperature T = -40 to 85oC A Drift 7 V/ oC Input Offset Current TA = 25oC 2 30 nA Input Bias Current TA = 25oC 20 150 nA BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 6 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Electrical Characteristics (Continued) Operating Conditions: VCC = +5V, TA= 25oC unless otherwise specified. Parameter Conditions Min Typ Max Unit 0.5 3 mV Op Amp Section (per Op Amp) (VCC = 5V, VO = 1.4V, TA = 25oC, unless otherwise noted) Input Offset Voltage TA = 25oC TA = -40 to 85oC 5 Input Offset Voltage Temperature T = -40 to 85oC A Drift 7 V/ oC Input Offset Current TA = 25oC 2 30 nA Input Bias Current TA = 25oC 20 150 nA Input Voltage Range VCC = 0 to 18V 0 VCC 1.5 V Common Mode Rejection Ratio TA = 25oC, VCM = 0 to 3.5V 70 85 dB Large Signal Voltage Gain VCC = 15V, RL = 2k, VO = 1.4 to 11.4V 85 100 dB Power Supply Rejection Ratio VCC = 5 to 18V 70 90 dB Output Current Source VCC = 15V, VID = 1V, VO = 2V 20 40 mA Sink VCC = 15V, VID = -1V, VO = 2V 10 20 mA Output Voltage Swing (High) VCC = 18, RL = 10k, VID = 1V 16 16.5 V Output Voltage Swing (Low) VCC = 18, RL = 10k, VID = -1V Slew Rate VCC = 18V, RL = 2k, AV = 1, VIN = 0.5 to 2V, CL = 100pF 0.3 0.5 V/ s Gain Bandwidth Product VCC = 18V, RL = 2k, CL = 100pF, VIN = 10mV, f=100kHz 0.7 1 MHz 17 100 mV BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 7 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Typical Performance Characteristics 150 150 100 AP4303-C VKA=VREF o 50 TA=25 C Cathode Current (mA) Cathode Current (mA) 100 0 -50 -100 AP4303-D VKA=VREF o TA=25 C 50 0 -50 -100 -150 -1 0 -150 1 -1 0 Cathode Voltage (V) Figure 6. Cathode Current vs. Cathode Voltage 1K 60 10K 1 Cathode Voltage (V) 100K 1000K Figure 7.Cathode Current vs. Cathode Voltage 60 5 50 Input Input and Output Voltage (V) 50 o TA = 25 C IKA = 10mA Av (dB) 40 40 4 3 30 30 20 20 10 10 1 0 0 0 1K 10K 100K o TA=25 C 2 Output 0 1000K 2 4 6 Time (S) Small Signal Frequency Figure 8. Voltage Reference Small Signal Voltage Gain vs. Frequency Figure 9. Pulse Response of VREF with respect to VKA BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 8 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Typical Performance Characteristics (Continued) 30 110 25 20 Voltage Gain(dB) Input Bias Current (nA) 100 VCC=15V 15 10 90 80 RL=2K RL=20K 70 5 0 -40 -20 0 20 40 60 80 100 60 120 0 o Ambient Temperature ( C) 2 4 6 8 10 12 14 16 18 Supply Voltage (V) Figure10. Op Amp Input Current Figure 11. Op Amp Voltage Gain 110 100 Voltage Gain(dB) 90 VCC: 10V to 15VDC o 80 o TA: -40 C to 85 C 70 R 10M 60 0.1uF VCC 50 40 VO VIN VCC/2 30 20 10 0 1HZ 10HZ 100HZ 1kHZ 10kHZ 100kHZ 1MHZ Frequency Figure 12. Open Loop Frequency Response BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 9 20 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Mechanical Dimensions DIP-16 Unit: mm(inch) 7.620(0.300)TYP 6 3.710(0.146) 4.310(0.170) 5 6 1.524(0.060)TYP 3.200(0.126) 3.600(0.142) 4 4 2.540(0.100) 0.510(0.020)MIN TYP 3.000(0.118) Depth 0.050(0.002) 0.150(0.006) 0.204(0.008) 0.360(0.014) 0.254(0.010) 0.360(0.014) 0.560(0.022) 0.700(0.028) 8.200(0.323) 9.400(0.370) 3.000(0.118) 3.600(0.142) 6.200(0.244) 6.600(0.260) 18.800(0.740) 19.200(0.756) R0.750(0.030) BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 10 Data Sheet QUAD OP AMP AND VOLTAGE REFERENCE AP4303 Mechanical Dimensions (Continued) SOIC-16 1.000(0.039) 1.300(0.051) Unit: mm(inch) 1.650(0.065) 0.700(0.028) 7 0.406(0.016) 2.000(0.079) Depth 0.060(0.002) 0.100(0.004) 7 B A 20:1 0.250(0.010) 0.500(0.020) 10.000(0.394) 1 5 R0.200(0.008) R0.200(0.008) 0.150(0.006) 0.250(0.010) 0.203(0.008) 6.040(0.238) 3.940(0.155) 8 9.5 0.200(0.008) S 1.000(0.039) 8 8 C-C 50:1 B 20:1 C 3 7 0.250(0.010) 0.200(0.008)MIN Depth 0.200(0.008) A 0.400(0.016)x45 1.000(0.039) 1.270(0.050) 0.600(0.024) C BCD Semiconductor Manufacturing Limited Apr. 2005 Rev. 1. 1 11 http://www.bcdsemi.com BCD Semiconductor Corporation 3170 De La Cruz Blvd, Suite # 105 Santa Clara, CA 95054-2411, U.S.A Tel: +1-408-988 6388, Fax: +1-408-988 6386 Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd. 800 Yi Shan Road, Shanghai 200233, PRC Tel: +86-21-6485-1491, Fax: +86-21-5450-0008 Advanced Analog Circuits (Shanghai) Corporation 8F, B Zone, 900 Yi Shan Road, Shanghai 200233, PRC Tel: +86-21-6495 9539, Fax: +86-21-6485 9673 BCD Semiconductor (Taiwan) Company Limited Room 2210, 22nd Fl, 333, Keelung Road, Sec. 1, TaiPei (110), Taiwan Tel: +886-2-2758 6828, Fax: +886-2-2758 6892 IMPORTANT NOTICE BCD Semiconductor Manufacturing Limited reserves the right to make changes without further notice to any products or specifications herein. BCD Semiconductor Manufacturing Limited does not assume any responsibility for use of any its products for any particular purpose, nor does BCD Semiconductor Manufacturing Limited assume any liability arising out of the application or use of any its products or circuits. BCD Semiconductor Manufacturing Limited does not convey any license under its patent rights or other rights nor the rights of others.