SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING GENERAL DESCRIPTION KEY PRODUCT FEATURES The SX8662 is an ultra low power, fully integrated 12-channel solution for capacitive touch-button matrix applications (up to 36 keys). Unlike many capacitive touch solutions, the SX8662 features dedicated capacitive sense inputs (that requires no external components) in addition to 8 general purpose I/O ports (GPIO) which can be used to drive up to 36 matrix LEDs (i.e. one per key). Each of the on-chip GPIO/LED driver is equipped with independent PWM source for enhanced visual effect such as dimming, and breathing. Complete Capacitive Touch-Button Solution The SX8662 includes a capacitive 10 bit ADC analog interface with automatic compensation up to 100pF. The high resolution capacitive sensing supports a wide variety of touch pad sizes and shapes and allows capacitive buttons to be created using thick overlay materials (up to 5mm) for an extremely robust and ESD immune system design. The SX8662 incorporates a versatile firmware that was specially designed to simplify capacitive touch solution design and offers reduced time-to-market. Integrated multi-time programmable memory provides the ultimate flexibility to modify key firmware parameters (gain, threshold, scan period, auto offset compensation) in the field without the need for new firmware development. The SX8662 supports the 400 kHz IC serial bus data protocol and includes a field programmable slave address. The tiny 5mm x 5mm footprint makes it an ideal solution for portable, battery powered applications where power and density are at a premium. o Up to 36 Matrix Buttons o Up to 36 LEDs Control for individual Visual Feedback with Auto Lightening o Configurable Single or Continuous Fading Mode o 256 steps PWM Linear and Logarithmic control High Resolution Capacitive Sensing o Up to 100pF of Offset Cap. Compensation at Full Sensitivity o Capable of Sensing up thru 5mm thick Overlay Materials Support of buzzer for audible feedback User-selectable Button Reporting Configuration Extremely Low Power o 8uA (typ) in Sleep Mode o 100uA (typ) in Doze Mode (195ms) o 460uA (typ) in Active Mode (30ms) Programmable Scanning Period from 15ms to several seconds Auto Offset Compensation o Eliminates false triggers due to environmental factors (temperature, humidity) o Initiated on power-up and configurable intervals Multi-Time In-Field Programmable Firmware Parameters for Ultimate Flexibility o On-chip user programmable memory for fast, self contained start-up No External Components per Sensor Input Internal Clock Requires No External Components Differential Sensor Sampling for Reduced EMI Optional 400 KHz IC Interface with Programmable Address -40C to +85C Operation APPLICATIONS TYPICAL APPLICATION CIRCUIT Home Automation White Goods buzzer SX8662 cap2 cap11 analog sensor interface clock generation RC Consumer Products, Instrumentation, Automotive PWM LED controller gpio6 cap4 cap9 Mechanical Button Replacement gpio5 cap5 power management gpio4 cap7 cap6 cap6 Notebook/Netbook/Portable/Handheld computers gnd micro processor GPIO controller RAM NVM ROM I2C cap7 gpio3 gpio2 cap8 36 Matrix LEDs cap3 Printers gpio7 vdig gnd vana cap1 cap10 cap8 cap3 cap2 cap1 ORDERING INFORMATION Part Number gpio1 Temperature Range cap5 gpio0 cap9 bottom plate 1 sda scl intb cp vdd cn cap10 Package SX8662I08AWLTRT -40C to +85C Lead Free MLPQ-W32 cap4 cap11 cap0 36 Capacitive Matrix Buttons resetb cap0 1 HOST th Rev5 4 August 2011 3000 Units/reel * This device is RoHS/WEEE compliant and Halogen Free (c) 2011 Semtech Corp. 1 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Table of Contents GENERAL DESCRIPTION ........................................................................................................................ 1 TYPICAL APPLICATION CIRCUIT ............................................................................................................ 1 KEY PRODUCT FEATURES..................................................................................................................... 1 APPLICATIONS....................................................................................................................................... 1 ORDERING INFORMATION...................................................................................................................... 1 1 GENERAL DESCRIPTION............................................................................................................... 4 1.1 1.2 1.3 1.4 1.5 2 Pin Diagram Marking information Pin Description Simplified Block Diagram Acronyms 4 4 5 6 6 ELECTRICAL CHARACTERISTICS ................................................................................................. 7 2.1 2.2 2.3 2.4 3 Absolute Maximum Ratings Recommended Operating Conditions Thermal Characteristics Electrical Specifications 7 7 7 8 FUNCTIONAL DESCRIPTION ........................................................................................................ 10 3.1 Introduction 3.1.1 General 3.1.2 Parameters 3.1.3 Configuration 3.2 Scan Period 3.3 Operation modes 3.4 Sensors on the PCB 3.4.1 Matrix Keys/Buttons (MK) 3.4.2 Priority Key/Button (PK) 3.4.3 Schematics Requirements 3.5 Button Information (MK and PK) 3.6 Analog Sensing Interface 3.7 Offset Compensation 3.8 Processing 3.9 Configuration 3.10 Power Management 3.11 Clock Circuitry 3.12 I2C interface 3.13 Interrupt 3.13.1 Power up 3.13.2 Assertion 3.13.3 Clearing 3.13.4 Example 3.14 Reset 3.14.1 Power up 3.14.2 RESETB th Rev5 4 August 2011 (c) 2011 Semtech Corp. 2 10 10 10 10 10 11 12 12 12 12 14 14 16 17 17 19 19 19 20 20 20 20 21 21 21 22 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.14.3 Software Reset 3.15 General Purpose Input and Outputs 3.15.1 GPO 3.15.2 Fading Modes 3.15.3 Intensity index vs PWM pulse width 3.15.4 Tri-State Multiplexing (TSM) 4 22 23 23 25 26 27 PIN DESCRIPTIONS ..................................................................................................................... 28 4.1 4.2 4.3 4.4 4.5 5 Introduction ASI pins Host interface pins Power management pins General purpose IO pins 28 28 29 32 33 DETAILED CONFIGURATION DESCRIPTIONS .............................................................................. 34 5.1 5.2 5.3 5.4 5.5 5.6 6 Introduction General Parameters Capacitive Sensors Parameters Buttons (MK and PK) Parameters Buzzer Parameters GPIO Parameters 34 37 38 40 43 44 I2C INTERFACE ........................................................................................................................... 47 6.1 6.2 6.3 6.4 6.5 6.6 I2C Write I2C read I2C Registers Overview Status Registers Control Registers SPM Gateway Registers 6.6.1 SPM Write Sequence 6.6.2 SPM Read Sequence 6.7 NVM burn 47 48 49 50 52 53 54 55 56 7 APPLICATION INFORMATION ...................................................................................................... 57 8 REFERENCES ............................................................................................................................. 58 9 PACKAGING INFORMATION ........................................................................................................ 59 9.1 9.2 Package Outline Drawing Land Pattern th Rev5 4 August 2011 59 59 (c) 2011 Semtech Corp. 3 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 1 GENERAL DESCRIPTION cap1 cap0 vana resetb gnd vdig gpio7 gpio6 Pin Diagram 32 31 30 29 28 27 26 25 cap2 1 24 gnd cap3 2 23 gpio5 cap4 3 22 gpio4 cap5 4 21 gpio3 cap6 5 20 gpio2 cap7 6 19 gnd cap8 7 18 gpio1 cap9 8 17 gpio0 SX8662 Top View 9 10 11 12 13 14 15 16 cap11 cn cp vdd intb scl sda bottom ground pad cap10 1.1 Figure 1 Pinout Diagram 1.2 Marking information ASX08 yyww xxxxxx R08 yyww = Date Code xxxxxx = Semtech lot number R08 = Semtech Code Figure 2 Marking Information th Rev5 4 August 2011 (c) 2011 Semtech Corp. 4 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 1.3 Pin Description Number Name Type Description 1 CAP2 Analog Capacitive Sensor 2 2 CAP3 Analog Capacitive Sensor 3 3 CAP4 Analog Capacitive Sensor 4 4 CAP5 Analog Capacitive Sensor 5 5 CAP6 Analog Capacitive Sensor 6 6 CAP7 Analog Capacitive Sensor 7 7 CAP8 Analog Capacitive Sensor 8 8 CAP9 Analog Capacitive Sensor 9 9 CAP10 Analog Capacitive Sensor 10 10 CAP11 Analog Capacitive Sensor 11 11 CN Analog Integration Capacitor, negative terminal (1nF between CN and CP) 12 CP Analog Integration Capacitor, positive terminal (1nF between CN and CP) 13 VDD Power Main input power supply 14 INTB Digital Output Interrupt, active LOW, requires pull up resistor (on host or external) 15 SCL Digital Input I2C Clock, requires pull up resistor (on host or external) 16 SDA Digital Input/Output I2C Data, requires pull up resistor (on host or external) 17 GPIO0 Digital Input/Output General Purpose Input/Output 0 18 GPIO1 Digital Input/Output General Purpose Input/Output 1 19 GND Ground Ground 20 GPIO2 Digital Input/Output General Purpose Input/Output 2 21 GPIO3 Digital Input/Output General Purpose Input/Output 3 22 GPIO4 Digital Input/Output General Purpose Input/Output 4 23 GPIO5 Digital Input/Output General Purpose Input/Output 5 24 GND Ground Ground 25 GPIO6 Digital Input/Output General Purpose Input/Output 6 26 GPIO7 Digital Input/Output General Purpose Input/Output 7 27 VDIG Analog Digital Core Decoupling, connect to a 100nF decoupling capacitor 28 GND Ground Ground 29 RESETB Digital Input Active Low Reset. Connect to VDD if not used. 30 VANA Analog Analog Core Decoupling, connect to a 100nF decoupling capacitor 31 CAP0 Analog Capacitive Sensor 0 32 CAP1 Analog Capacitive Sensor 1 Ground Exposed pad connect to ground Bottom Plate GND Table 1 Pin description th Rev5 4 August 2011 (c) 2011 Semtech Corp. 5 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 1.4 Simplified Block Diagram gpio6 gpio7 vdig gnd resetb vana cap0 cap1 The simplified block diagram of the SX8662 is illustrated in Figure 3. SX8662 cap2 cap3 analog sensor interface clock generation RC PWM LED controller gnd gpio5 gpio4 cap4 power management cap5 cap6 cap7 cap8 gpio3 micro processor GPIO controller RAM NVM ROM I2C gpio2 gnd gpio1 gpio0 cap9 sda scl intb vdd cp cn cap11 cap10 bottom plate Figure 3 Simplified block diagram of the SX8662 1.5 Acronyms ASI DCV GPO GPP MTP NVM PWM QSM SPM SPO MK PK PS TSM Analog Sensor Interface Digital Compensation Value General Purpose Output General Purpose PWM Multiple Time Programmable Non Volatile Memory Pulse Width Modulation Quick Start Memory Shadow Parameter Memory Special Purpose Output Matrix Key Priority Key Proximity Sensor Tri-State Multiplexing th Rev5 4 August 2011 (c) 2011 Semtech Corp. 6 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 2 ELECTRICAL CHARACTERISTICS 2.1 Absolute Maximum Ratings Stresses above the values listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these, or any other conditions beyond the "Recommended Operating Conditions", is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameter Symbol Min. Max. Unit Supply Voltage VDD -0.5 3.9 V Input voltage (non-supply pins) VIN -0.5 3.9 V Input current (non-supply pins) IIN 10 mA Operating Junction Temperature TJCT 125 C Reflow temperature TRE 260 C Storage temperature TSTOR -50 150 C ESDHBM 3 kV ILU 100 mA ESD HBM (Human Body model) Latchup (i) (ii) Table 2 Absolute Maximum Ratings (i) Tested to JEDEC standard JESD22-A114 (ii) Tested to JEDEC standard JESD78 2.2 Recommended Operating Conditions Parameter Symbol Min. Max. Unit Supply Voltage VDD 2.7 3.6 V 100 mV Supply Voltage Drop (iii, iv, v) VDDdrop Supply Voltage for NVM programming VDD 3.0 3.6 V Ambient Temperature Range TA -40 85 C Table 3 Recommended Operating Conditions (iii) Performance for 2.6V < VDD < 2.7V might be degraded. (iv) Operation is not guaranteed below 2.6V. Should VDD briefly drop below this minimum value, then the SX8662 may require; - a hardware reset issued by the host using the RESETB pin - a software reset issued by the host using the I2C interface (v) In the event the host processor is reset or undergoes a power OFF/ON cycle, it is recommended that the host also resets the SX8662 and assures that parameters are re-written into the SPM (should these differ to the parameters held in NVM). 2.3 Thermal Characteristics Parameter Thermal Resistance - Junction to Ambient Symbol (vi) JA Min. Max. Unit 25 C/W Table 4 Thermal Characteristics (vi) Static airflow th Rev5 4 August 2011 (c) 2011 Semtech Corp. 7 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 2.4 Electrical Specifications All values are valid within the operating conditions unless otherwise specified. Parameter Symbol Conditions Min. Typ. Max. Unit Active mode, average IOP,active 30ms scan period, 12 sensors enabled, minimum sensitivity 460 uA Doze mode, average IOP,Doze 195ms scan period, 12 sensors enabled, minimum sensitivity 100 uA Sleep IOP,sleep I2C listening, sensors disabled 8 Current consumption 17 uA 0.7*VDD VDD + 0.3 V VSS - 0.3 0.8 V 1 uA ResetB, SCL, SDA Input logic high VIH Input logic low VIL VSS applied to GND pins Input leakage current LI CMOS input Pull up resistor RPU when enabled 660 k Pull down resistor RPD when enabled 660 k Output logic high VOH IOH<4mA Output logic low VOL GPIO set as Output, INTB, SDA VDD-0.4 V IOL,GPIO<12mA 0.4 V 400 ms IOL,SDA,INTB<4mA Start-up Power up time tpor time between rising edge VDD and rising INTB RESETB ResetB pulse width tres 50 ns Recommended External components capacitor between VDIG, GND Cvdig type 0402, tolerance +/-50% 100 nF capacitor between VANA, GND Cvana type 0402, tolerance +/-50% 100 nF capacitor between CP, CN Cint type 0402, COG, tolerance +/-5% 1 nF capacitor between VDD, GND Cvdd type 0402, tolerance +/-50% 100 nF Table 5 Electrical Specifications th Rev5 4 August 2011 (c) 2011 Semtech Corp. 8 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Parameter I2C Timing Specifications Symbol Conditions Min. Typ. Max. Unit 400 KHz (i) SCL clock frequency fSCL SCL low period tLOW 1.3 us SCL high period tHIGH 0.6 us Data setup time tSU;DAT 100 ns Data hold time tHD;DAT 0 ns Repeated start setup time tSU;STA 0.6 us Start condition hold time tHD;STA 0.6 us Stop condition setup time tSU;STO 0.6 us Bus free time between stop and start tBUF 500 us Input glitch suppression tSP 50 ns Table 6 I2C Timing Specification Notes: (i) All timing specifications, Figure 4 and Figure 5, refer to voltage levels (VIL, VIH, VOL) defined in Table 5. The interface complies with slave F/S mode as described by NXP: "I2C-bus specification, Rev. 03 - 19 June 2007" Figure 4 I2C Start and Stop timing Figure 5 I2C Data timing th Rev5 4 August 2011 (c) 2011 Semtech Corp. 9 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3 FUNCTIONAL DESCRIPTION 3.1 3.1.1 Introduction General The SX8662 is intended to be used in applications which require capacitive sensors covered by isolating overlay material. A finger approaching the capacitive sensors will change the charge that can be loaded on the sensors. The SX8662 measures the change of charge and converts that into digital values (ticks). The larger the charge on the sensors, the larger the number of ticks will be. The charge to ticks conversion is done by the SX8662 Analog Sensor Interface (ASI). The ticks are further processed by the SX8662 and converted in a high level, easy to use information for the user's host. The information between SX8662 and the host is passed through the I2C interface with an additional interrupt signal indicating that the SX8662 has new information. For buttons this information is simply touched or released. User feedback, done through the SX8662's GPIOs, can be visual via LEDs and/or audio via a buzzer. 3.1.2 Parameters The SX8662 has many low level built-in, fixed algorithms and procedures. To allow a lot of freedom for the user and adapt the SX8662 for different applications these algorithms and procedures can be configured with a large set of parameters which will be described in the following sections. Sensitivity and detection thresholds of the sensors are part of these parameters. Assuming that overlay material and sensors areas are identical then the sensitivities and thresholds will be the same for each sensor. In case sensors are not of the same size then sensitivities or thresholds might be chosen individually per sensor. So a smaller size sensor can have a larger sensitivity while a big size sensor may have the lower sensitivity. 3.1.3 Configuration During a development phase the parameters can be determined and fine tuned by the users and downloaded over the I2C in a dynamic way. The parameter set can be downloaded over the I2C by the host each time the SX8662 boots up. This allows a flexible way of setting the parameters at the expense of I2C occupation. In case the parameters are frozen they can be programmed in Multiple Time Programmable (MTP) Non Volatile Memory (NVM) on the SX8662. The programming needs to be done once (over the I2C). The SX8662 will then boot up from the NVM and additional parameters from the host are not required anymore. In case the host desires to overwrite the boot-up NVM parameters (partly or even complete) this can be done by additional I2C communications. 3.2 Scan Period The basic operation Scan period of the SX8662 sensing interface can be split into three periods over time. In the first period (Sensing) the SX8662 is sensing all enabled CAP inputs, from CAP0 towards CAP11. In the second period (Processing) the SX8662 processes the sensor data, verifies and updates the GPIO and the I2C. In the third period (Timer) the SX8662 is set in a low power mode and waits until a new cycle starts. Figure 6 shows the different SX8662 periods over time. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 10 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Figure 6 Scan Period The scan period determines the minimum reaction time of the SX8662. The scan period can be configured by the host from 15ms to values larger than a second. The reaction time is defined as the interval between a touch on the sensor and the moment that the SX8662 generates the interrupt on the INTB pin. The shorter the scan period the faster the reaction time will be. Very low power consumptions can be obtained by setting very long scan periods with the expense of having longer reaction times. All external events like GPIO, I2C and the interrupt are updated in the processing period, so once every scan period. 3.3 Operation modes The SX8662 has 3 operation modes. The main difference is found in the reaction time (corresponding to the scan period) and power consumption. Active mode offers fast scan periods. The typical reaction time is 30ms. All enabled sensors are scanned and information data is processed within this interval. Doze mode increases the scan period time which increases the reaction time to 195ms typical and at the same time reduces the operating current. Sleep mode turns the SX8662 OFF, except for the I2C peripheral, minimizing operating current while maintaining the power supplies. In Sleep mode the SX8662 does not do any sensor scanning. The Sleep mode will be exited by any I2C access. The user can specify other scan periods for the Active and Doze mode and decide for other compromises between reaction time and power consumption. In most applications the reaction time needs to be fast when fingers are present, but can be slow when no person uses the application. In case the SX8662 is not used for a specific time it will go from Active mode into Doze mode and power will be saved. This time-out is determined by the Passive Timer which can be configured by the user or turned OFF if not required. To leave Doze mode and enter Active mode this can be done by a simple touch on any button. The host can decide to force the operating mode by issuing commands over the I2C (using register CompOpMode) and take fully control of the SX8662. The diagram in Figure 7 shows the available operation modes and the possible transitions. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 11 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Figure 7 Operation modes 3.4 3.4.1 Sensors on the PCB Matrix Keys/Buttons (MK) In opposition to most of the other Semtech capacitive sensing products where 1 button = 1 sensor (CAP0...CAP11)., the SX8662 requires sensors to be routed in matrix and each button is formed by the intersection/concatenation of two sensors areas. The buttons are covered by isolating overlay material (typically 1mm...3mm). The area of a button is typically one square centimetre which corresponds about to the area of a finger touching the overlay material. Figure 8 Matrix buttons layout/connections (Red = Top; Brown = Inner1; Blue = Inner2) IMPORTANT: Please note that while the matrix structure allows increasing dramatically the potential maximum number of buttons (up to 36 with only 12 sensors) it also limits the operation to max one matrix button reported at a time (ie single button touch operation). When several matrix buttons are touched only the first one is reported. 3.4.2 Priority Key/Button (PK) When the priority key is enabled in BtnCfg[6], CAP11 can be routed outside the matrix to a separate standard button sensor. Matrix size is then reduced to 6x5 keys (CAP0...CAP10). Priority key operation/reporting is independent from the matrix and can be used for any "high priority" key (Power, Reset, etc) or "multi-touch" function (Shift, Alt, etc). 3.4.3 Schematics Requirements For each PK combination, a specific schematic must be followed on the board as illustrated in figure below. th Rev5 4 August 2011 (c) 2011 Semtech Corp. www.semtech.com 12 SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING MK 35 MK 34 MK 33 MK 32 MK 31 CAP11 MK 25 MK 24 MK 23 MK 22 MK 21 MK 30 CAP9 MK 25 MK 24 MK 23 MK 22 MK 21 MK 30 CAP9 MK 16 MK 15 MK 14 MK 13 MK 20 MK 29 CAP7 MK 16 MK 15 MK 14 MK 13 MK 20 MK 29 CAP7 MK 9 MK 8 MK 7 MK 12 MK 19 MK 28 CAP6 MK 9 MK 8 MK 7 MK 12 MK 19 MK 28 CAP6 MK 4 MK 3 MK 6 MK 11 MK 18 MK 27 CAP5 MK 4 MK 3 MK 6 MK 11 MK 18 MK 27 CAP5 MK 1 MK 2 MK 5 MK 10 MK 17 MK 26 CAP4 MK 1 MK 2 MK 5 MK 10 MK 17 MK 26 CAP4 CAP0 CAP1 CAP2 CAP3 CAP8 CAP10 CAP0 CAP1 CAP2 CAP3 CAP8 CAP10 MK 36 PK = ON (CAP11) PK = OFF Figure 9 Sensors Schematics Requirements vs Configuration th Rev5 4 August 2011 (c) 2011 Semtech Corp. 13 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.5 Button Information (MK and PK) The touch buttons have two simple states (see Figure 10): ON (touched by finger) and OFF (released and no finger press). Figure 10 Buttons A finger touch is reported as soon as the ASI ticks of both sensors forming the button exceed their user-defined threshold plus a hysteresis. A finger release is reported as soon as the ASI ticks of one at least of the sensors forming the button goes below its user-defined threshold minus a hysteresis. The hysteresis around the threshold avoids rapid touch and release signalling during transients. IMPORTANT: Please note that while the matrix structure allows increasing dramatically the potential maximum number of buttons (up to 36 with only 12 sensors) it also limits the operation to max one matrix button reported at a time (ie single button touch operation). When two matrix buttons are touched only the first one is reported. 3.6 Analog Sensing Interface The Analog Sensing Interface (ASI) converts the charge on the sensors into ticks which will be further digitally processed. The basic principle of the ASI will be explained in this section. The ASI consists of a multiplexer selecting the sensor, analog switches, a reference voltage, an ADC sigma delta converter, an offset compensation DAC and an external integration capacitor (see Figure 11). Figure 11 Analog Sensor Interface To get the ticks representing the charge on a specific sensor the ASI will execute several steps. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 14 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING The charge on a sensor cap (e.g CAP0) will be accumulated multiple times on the external integration capacitor, Cint. This results in an increasing voltage on Cint proportional to the capacitance on CAP0. At this stage the offset compensation DAC is enabled. The compensation DAC generates a voltage proportional to an estimation of the external capacitance. The estimation is obtained by the offset compensation procedure executed e.g. at power-up. The difference between the DAC output and the charge on Cint is the desired signal. In the ideal case the difference of charge will be converted to zero ticks if no finger is present and the number of ticks becomes high in case a finger is present. The difference of charge on Cint and the DAC output will be transferred to the ADC (Sigma Delta Integrator). After the charge transfer to the ADC the steps above will be repeated. The larger the number the cycles are repeated the larger the signal out of the ADC with improved SNR. The sensitivity is therefore directly related to the number of cycles. The SX8662 allows setting the sensitivity for each sensor individually in applications which have a variety of sensors sizes or different overlays or for fine-tuning performances. The optimal sensitivity is depending heavily on the final application. If the sensitivity is too low the ticks will not pass the thresholds and user detection will not be possible. In case the sensitivity is set too large, some power will be wasted and false touch information may be output (i.e. for touch buttons => finger not touching yet). Once the ASI has finished the first sensor, the ticks are stored and the ASI will start measuring the next sensor until all (enabled) sensors pins have been treated. In case some sensors are disabled then these result in lower power consumption simply because the ASI is active for a shorter period and the following processing period will be shorter. The ticks from the ASI will then be handled by the digital processing. The ASI will shut down and wait until new sensing period will start. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 15 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.7 Offset Compensation The capacitance at the CAP pins is determined by an intrinsic capacitance of the integrated circuit, the PCB traces, ground coupling and the sensor planes. This capacitance is relatively large and might become easily some tens of pF. This parasitic capacitance will vary only slowly over time due to environmental changes. A finger touch is in the order of one pF. If the finger approaches the sensor this occurs typically fast. The ASI has the difficult task to detect and distinguish a small, fast changing capacitance, from a large, slow varying capacitance. This would require a very precise, high resolution ADC and complicated, power consuming, digital processing. The SX8662 features a 16 bit DAC which compensates for the large, slow varying capacitance already in front of the ADC. In other words the ADC converts only the desired small signal. In the ideal world the ADC will put out zero ticks even if the external capacitance is as high as 100pF. At each power-up of the SX8662 the Digital Compensation Values (DCV) are estimated by the digital processing algorithms. The algorithm will adjust the compensation values such that zero ticks will be generated by the ADC. Once the correct compensation values are found these will be stored and used to compensate each CAP pin. If the SX8662 is shut down the compensation values will be lost. At a next power-up the procedure starts all over again. This assures that the SX8662 will operate under any condition. Powering up at e.g. different temperatures will not change the performance of the SX8662 and the host does not have to do anything special. The DCVs do not need to be updated if the external conditions remain stable. However if e.g. temperature changes this will influence the external capacitance. The ADC ticks will drift then slowly around zero values basically because of the mismatch of the compensation circuitry and the external capacitance. In case the average value of the ticks become higher than the positive noise threshold (configurable by user) or lower than the negative threshold (configurable by user) then the SX8662 will initiate a compensation procedure and find a new set of DCVs. Compensation procedures can as well be initiated by the SX8662 on periodic intervals. Even if the ticks remain within the positive and negative noise thresholds the compensation procedure will then estimate new sets of DCVs. Finally the host can initiate a compensation procedure by using the I2C interface. This is e.g. required after the host changed the sensitivity of sensors. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 16 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.8 Processing The first processing step of the raw ticks, coming out of the ASI, is low pass filtering to obtain an estimation of the average capacitance: tick-ave (see Figure 12). This slowly varying average is important in the detection of slowly changing environmental changes. ASI processing SPM processing ticks (raw) tick-diff PWM LED controller tick-ave GPIO controller low pass I2C compensation DCV Figure 12 Processing The difference of the tick average and the raw ticks, tick-diff, is a good estimation of rapid changing input capacitances. The tick-diff, tick-ave and the configuration parameters in the SPM are then processed and determines the sensor information, I2C registers status and PWM control. 3.9 Configuration Figure 13 shows the building blocks used for configuring the SX8662. Figure 13 Configuration The default configuration parameters of the SX8662 are stored in the Quick Start Memory (QSM). This configuration data is setup to a very common application for the SX8662 with 8 buttons. Without any programming or host interaction the SX8662 will start up in the Quick Start Application. The QSM settings are fixed and cannot be changed by the user. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 17 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING In case the application needs different settings than the QSM settings then the SX8662 can be setup and/or programmed over the I2C interface. The configuration parameters of the SX8662 can be stored in the Multiple Time Programmable (MTP) Non Volatile Memory (NVM). The NVM contains all those parameters that are defined and stable for the application. Examples are the number of sensors enabled, sensitivity, active and Doze scan period. The details of these parameters are described in the next chapters. At power up the SX8662 checks if the NVM contains valid data. In that case the configuration parameter source becomes the NVM. If the NVM is empty or non-valid then the configuration source becomes the QSM. In the next step the SX8662 copies the configuration parameter source into the Shadow Parameter Memory (SPM). The SX8662 is operational and uses the configuration parameters of the SPM. During power down or reset event the SPM loses all content. It will automatically be reloaded following power up or at the end of the reset event. The host will interface with the SX8662 through the I2C bus and the analog output interface. The I2C of the SX8662 consists of 16 registers. Some of these I2C registers are used to read the status and information of the buttons. Other I2C registers allow the host to take control of the SX8662. The host can e.g. decide to change the operation mode from active mode to Doze mode or go into sleep (according Figure 7). Two additional modes allow the host to have an access to the SPM or indirect access to the NVM. These modes are required during development, can be used in real time or in-field programming. Figure 14 shows the Host SPM mode. In this mode the host can decide to overwrite the SPM. This is useful during the development phases of the application where the configuration parameters are not yet fully defined and as well during the operation of the application if some parameters need small deviations from the QSM or NVM content. Figure 14 Host SPM mode The content of the SPM remains valid as long as the SX8662 is powered. After a power down the host needs to re-write the SPM at the next power-up. Figure 15 shows the Host NVM mode. In this mode the host will be able to write the NVM. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 18 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Figure 15 Host NVM mode The writing of the host towards the NVM is not done directly but done in 2 steps (Figure 15). In the first step the host writes to the SPM (as in Figure 14). In the second step the host signals the SX8662 to copy the SPM content into the NVM. Initially the NVM memory is empty and it is required to determine a valid parameter set for the application. This can be done during the development phase using dedicated evaluation hardware representing the final application. This development phase uses probably initially the host SPM mode which allows faster iterations. Once the parameter set is determined this can be written to the NVM over the I2C using the 2 steps approach by the host or a dedicated programmer for large volumes production (as described in the paragraphs 6.6 and 6.7). 3.10 Power Management The SX8662 uses on-chip voltage regulators which are controlled by the on-chip microprocessor. The regulators need to be stabilized with an external capacitor between VANA and ground and between VDIG and ground (see Table 5). Both regulators are designed to only drive the SX8662 internal circuitry and must not be loaded externally. 3.11 Clock Circuitry The SX8662 has its own internal clock generation circuitry that does not require any external components. The clock circuitry is optimized for low power operation and is controlled by the on-chip microprocessor. The typical operating frequency of the oscillating core is 16.7MHz from which all other lower frequencies are derived. 3.12 I2C interface The I2C interface allows the communication between the host and the SX8662. The I2C slave implemented on the SX8662 is compliant with the standard (100kb/s) and fast mode (400kb/s) The default SX8662 I2C address equals 0b010 1011. A different I2C address can be programmed by the user in the NVM. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 19 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.13 Interrupt 3.13.1 Power up During power up the INTB is kept low. Once the power up sequence is terminated the INTB is cleared autonomously. The SX8662 is then ready for operation. Figure 16 Power Up vs. INTB During the power on period the SX8662 stabilizes the internal regulators, RC clocks and the firmware initializes all registers. During the power up the SX8662 is not accessible and I2C communications are forbidden. The GPIOs set as inputs with a pull up resistor. As soon as the INTB rises the SX8662 will be ready for I2C communication. The GPIOs are then configured according the parameters in the SPM. The value of INTB before power up depends on the INTB pull up resistor supply voltage. 3.13.2 Assertion INTB is updated in Active or Doze mode once every scan period. The INTB will be asserted at the following events: * if a Button event occurred (touch or release if enabled). I2C register CapStatKeys show the detailed status of the Buttons, * when actually entering Active or Doze mode via a host request (may be delayed by 1 scan period). I2C register CompOpmode shows the current operation mode, * once compensation procedure is completed either through automatic trigger or via host request (may be delayed by 1 scan period), * once SPM write is effective (may be delayed by 1 scan period), * once NVM burn procedure is completed (may be delayed by 1 scan period), * during reset (power up, hardware RESETB, software reset). 3.13.3 Clearing The clearing of the INTB is done as soon as the host performs a read to any of the SX8662 I2C registers. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 20 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.13.4 Example A typical example of the assertion and clearing of the INTB and the I2C communication is shown in Figure 17. Figure 17 Interrupt and I2C When a button is touched the SX8662 will assert the interrupt (1). The host will read the SX8662 status information over the I2C (2) and this clears the interrupt. If the finger releases the button the interrupt will be asserted (3), the host reads the status (4) which clears the interrupt. In case the host will not react to an interrupt then this will result in a missing touch. 3.14 Reset The reset can be performed by 3 sources: - power up, - RESETB pin, - software reset. 3.14.1 Power up During power up the INTB is kept low. Once the power up sequence is terminated the INTB is released autonomously. The SX8662 is then ready for operation. Figure 18 Power Up vs. INTB th Rev5 4 August 2011 (c) 2011 Semtech Corp. 21 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING During the power on period the SX8662 stabilizes the internal regulators, RC clocks and the firmware initializes all registers. During the power up the SX8662 is not accessible and I2C communications are forbidden. As soon as the INTB rises the SX8662 will be ready for I2C communication. 3.14.2 RESETB When RESETB is driven low the SX8662 will reset and start the power up sequence as soon as RESETB is driven high or pulled high. In case the user does not require a hardware reset control pin then the RESETB pin can be connected to VDD. Figure 19 Hardware Reset 3.14.3 Software Reset To perform a software reset the host needs to write 0xDE followed by 0x00 at the SoftReset register at address 0xB1. Figure 20 Software Reset th Rev5 4 August 2011 (c) 2011 Semtech Corp. 22 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 3.15 General Purpose Input and Outputs The SX8662 offers eight General Purpose Input and Outputs (GPIO) pins which can be configured in any of these modes: - GPO (General Purpose Output) with Autoligth ON/OFF - SPO (Special Purpose Output). GPIO7 only; in this mode the GPIO can be connected to an external buzzer. The input state of the GPIO is only used during the initial phase of the power up period. Each of these GPIO modes is described in more details in the following sections. The polarity of the GPO pins is defined as in figure below, driving an LED as example. It has to be set accordingly in SPM parameter GpioPolarity. Figure 21 polarity = 1/Normal (a), polarity = 0/Inverted (b) The PWM blocks used GPO modes are 8-bits based and clocked at 2MHz typ. hence offering 256 selectable pulse width values with a granularity of 0.5us typ. Figure 22 PWM definition, (a) small pulse width, (b) large pulse width 3.15.1 GPO GPIOs configured as GPO will operate as digital outputs which can generate both standard low/high logic levels and PWM low/high duty cycles levels. Typical application is LED ON/OFF control. Transitions between ON and OFF states can be triggered either automatically (Autolight ON) or manually by the host (Autolight OFF). This is illustrated in figures below. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 23 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Figure 23 LED Control in GPO mode, Autolight OFF Figure 24 LED Control in GPO mode, Autolight ON Additionally these transitions can be configured to be done with or without fading following a logarithmic or linear function. This is illustrated in figures below. Figure 25 GPO ON transition (LED fade in), normal polarity, (a) linear, (b) logarithmic Figure 26 GPO ON transition (LED fade in), inverted polarity, (a) linear, (b) logarithmic The fading out (e.g. after a button is released) is identical to the fading in but an additional off delay can be added before the fading starts (Figure 27 and Figure 28). th Rev5 4 August 2011 (c) 2011 Semtech Corp. 24 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Figure 27 GPO OFF transition (LED fade out), normal polarity, (a) linear, (b) logarithmic Figure 28 GPO OFF transition (LED fade out), inverted polarity, (a) linear, (b) logarithmic Please note that standard high/low logic signals are just a specific case of GPO mode and can also be generated simply by setting inc/dec time to 0 (i.e. OFF) and programming intensity OFF/ON to 0x00 and 0xFF. 3.15.2 Fading Modes The SX8662 supports two different fading modes, namely Single and Continuous. These fading modes can be configured for each GPIO individually. Please see 5.6 "GPIO Parameters" for more information on how to configure this feature. i) Single Fading Mode: The GPO pin fades in when the associated button is touched and it fades out when it is released. This is shown in Figure 29 OFF OFF ON ON intensity OFF intensity OFF intensity fading-in delay_off fading-out Figure 29 Single Fading Mode ii) Continuous Fading Mode: th Rev5 4 August 2011 (c) 2011 Semtech Corp. 25 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING The GPO pin fades in and fades out continuously when the associated button is touched. The fading in and out stops when the button is released. This is shown in Figure 30. OFF ON ON intensity OFF intensity OFF intensity fading-in fading-out Figure 30 Continuous Fading Mode 3.15.3 Intensity index vs PWM pulse width Tables below are used to convert all intensity indexes parameters GpioIntensityOff, GpioIntensityOn and GppIntensity but also to generate fading in GPO mode During fading in(out), the index is automatically incremented(decremented) at every Inc(Dec)Time x Inc(Dec)Factor until it reaches the programmed GpioIntensityOn(Off) value. Index 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Lin/Log 0/0 2/0 3/0 4/0 5/0 6/2 7/2 8/2 9/2 10/2 11/2 12/2 13/2 14/2 15/3 16/3 17/3 18/3 19/3 20/3 21/3 22/3 23/3 24/4 25/4 26/4 27/4 28/4 29/4 30/4 31/4 32/5 Index 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Lin/Log 33/5 34/5 35/5 36/5 37/5 38/6 39/6 40/6 41/6 42/6 43/7 44/7 45/7 46/7 47/7 48/8 49/8 50/8 51/8 52/9 53/9 54/9 55/9 56/10 57/10 58/10 59/10 60/11 61/11 62/11 63/12 64/12 Index 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 Lin/Log 65/12 66/13 67/13 68/13 69/14 70/14 71/14 72/15 73/15 74/15 75/16 76/16 77/16 78/17 79/17 80/18 81/18 82/19 83/19 84/20 85/20 86/21 87/21 88/22 89/22 90/23 91/23 92/24 93/24 94/25 95/25 96/26 Index 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 Lin/Log 97/26 98/27 99/27 100/28 101/29 102/29 103/30 104/30 105/31 106/32 107/32 108/33 109/33 110/34 111/35 112/35 113/36 114/37 115/38 116/38 117/39 118/40 119/40 120/41 121/42 122/43 123/44 124/44 125/45 126/46 127/47 128/48 Index 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 Lin/Log 129/48 130/49 131/50 132/51 133/52 134/53 135/54 136/55 137/55 138/56 139/57 140/58 141/59 142/60 143/61 144/62 145/63 146/64 147/65 148/66 149/67 150/68 151/69 152/71 153/72 154/73 155/74 156/75 157/76 158/77 159/78 160/80 Index 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 Lin/Log 161/81 162/82 163/83 164/84 165/86 166/87 167/88 168/89 169/91 170/92 171/93 172/95 173/96 174/97 175/99 176/100 177/101 178/103 179/104 180/106 181/107 182/109 183/110 184/111 185/113 186/114 187/116 188/117 189/119 190/121 191/122 192/124 Index 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 Lin/Log 193/125 194/127 195/129 196/130 197/132 198/133 199/135 200/137 201/139 202/140 203/142 204/144 205/146 206/147 207/149 208/151 209/153 210/155 211/156 212/158 213/160 214/162 215/164 216/166 217/168 218/170 219/172 220/174 221/176 222/178 223/180 224/182 Index 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Lin/Log 225/184 226/186 227/188 228/190 229/192 230/194 231/197 232/199 233/201 234/203 235/205 236/208 237/210 238/212 239/215 240/217 241/219 242/221 243/224 244/226 245/229 246/231 247/233 248/236 249/238 250/241 251/243 252/246 253/248 254/251 255/253 256/256 Lin/Log 64/131 63/129 Index 224 225 Lin/Log 32/72 31/70 Table 7 Intensity index vs. PWM pulse width (normal polarity) Index 0 1 Lin/Log 256/256 255/256 th Index 32 33 Lin/Log 224/251 223/251 Rev5 4 August 2011 Index 64 65 Lin/Log 192/244 191/243 Index 96 97 Lin/Log 160/230 159/229 Index 128 129 Lin/Log 128/208 127/207 (c) 2011 Semtech Corp. 26 Index 160 161 Lin/Log 96/175 95/174 Index 192 193 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 254/256 253/256 252/256 251/254 250/254 249/254 248/254 247/254 246/254 245/254 244/254 243/254 242/253 241/253 240/253 239/253 238/253 237/253 236/253 235/253 234/253 233/252 232/252 231/252 230/252 229/252 228/252 227/252 226/252 225/251 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 222/251 221/251 220/251 219/250 218/250 217/250 216/250 215/250 214/249 213/249 212/249 211/249 210/249 209/248 208/248 207/248 206/248 205/247 204/247 203/247 202/247 201/246 200/246 199/246 198/246 197/245 196/245 195/245 194/244 193/244 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 190/243 189/243 188/242 187/242 186/242 185/241 184/241 183/241 182/240 181/240 180/240 179/239 178/239 177/238 176/238 175/237 174/237 173/236 172/236 171/235 170/235 169/234 168/234 167/233 166/233 165/232 164/232 163/231 162/231 161/230 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 158/229 157/228 156/227 155/227 154/226 153/226 152/225 151/224 150/224 149/223 148/223 147/222 146/221 145/221 144/220 143/219 142/218 141/218 140/217 139/216 138/216 137/215 136/214 135/213 134/212 133/212 132/211 131/210 130/209 129/208 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 126/206 125/205 124/204 123/203 122/202 121/201 120/201 119/200 118/199 117/198 116/197 115/196 114/195 113/194 112/193 111/192 110/191 109/190 108/189 107/188 106/187 105/185 104/184 103/183 102/182 101/181 100/180 99/179 98/178 97/176 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 94/173 93/172 92/170 91/169 90/168 89/167 88/165 87/164 86/163 85/161 84/160 83/159 82/157 81/156 80/155 79/153 78/152 77/150 76/149 75/147 74/146 73/145 72/143 71/142 70/140 69/139 68/137 67/135 66/134 65/132 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 62/127 61/126 60/124 59/123 58/121 57/119 56/117 55/116 54/114 53/112 52/110 51/109 50/107 49/105 48/103 47/101 46/100 45/98 44/96 43/94 42/92 41/90 40/88 39/86 38/84 37/82 36/80 35/78 34/76 33/74 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 30/68 29/66 28/64 27/62 26/59 25/57 24/55 23/53 22/50 21/48 20/46 19/44 18/41 17/39 16/37 15/35 14/32 13/30 12/27 11/25 10/23 9/20 8/18 7/15 6/13 5/10 4/8 3/5 2/3 0/0 Table 8 Intensity index vs. PWM pulse width (inverted polarity) 3.15.4 Tri-State Multiplexing (TSM) SX8662 can support up to 36 individual LEDs ie one per matrix key. To make this possible with the limited GPIOs available a Tri-State Multiplexing driver has been implemented on chip and a specific LED matrix connection must be followed for correct operation. Figure 31 Tri-State Multiplexing Schematics (DMKx = LED of button MKx, Cf Figure 48) Whenever set to GPO with Autolight ON, GPIO0-6 (GPIO0-5 if PK is enabled) are automatically configured for TSM operation. If PK is enabled the matrix is reduced to 6x5 LEDs, DMK31-36 can be removed and GPIO6 is automatically used for PK independent LED feedback (if Autoligth ON, else can be controlled by the host). th Rev5 4 August 2011 (c) 2011 Semtech Corp. 27 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 4 PIN DESCRIPTIONS 4.1 Introduction This chapter describes briefly the pins of the SX8662, the way the pins are protected, if the pins are analog, digital, require pull up or pull down resistors and show control signals if these are available. 4.2 ASI pins CAP0, CAP1,...,CAP11 The capacitance sensor pins (CAP0, CAP1,..., CAP11) are connected directly to the ASI circuitry which converts the sensed capacitance into digital values. The capacitance sensor pins which are not used should be left open. The enabled CAP pins need be connected directly to the sensors without significant resistance (typical below some ohms, connection vias are allowed). The capacitance sensor pins are protected to VANA and GROUND. Figure 32 shows the simplified diagram of the CAP0, CAP1,...CAP11 pins. SX8662 VANA sensor CAPx CAP_INx ASI Note : x = 0, 1,2,...7 Figure 32 Simplified diagram of CAP0, CAP1,...,CAP11 CN, CP The CN and the CP pins are connected to the ASI circuitry. A 1nF sampling capacitor between CP and CN needs to be placed as close as possible to the SX8662. The CN and CP are protected to VANA and GROUND. Figure 33 shows the simplified diagram of the CN and CP pins. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 28 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING SX8662 VANA CP ASI VANA CN Figure 33 Simplified diagram of CN and CP 4.3 Host interface pins The host interface consists of the interrupt pin INTB, a reset pin RESETB and the standard I2C pins: SCL and SDA. INTB The INTB pin is an open drain output that requires an external pull-up resistor (1..10 kOhm). The INTB pin is protected to VDD using dedicated devices. The INTB pin has diode protected to GROUND. Figure 34 shows a simplified diagram of the INTB pin. VDD SX8662 R_INT INTB to host INT Figure 34 Simplified diagram of INTB th Rev5 4 August 2011 (c) 2011 Semtech Corp. 29 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING SCL The SCL pin is a high impedance input pin. The SCL pin is protected to VDD, using dedicated devices, in order to conform to standard I2C slave specifications. The SCL pin has diode protected to GROUND. An external pull-up resistor (1..10 kOhm) is required on this pin. Figure 35 shows the simplified diagram of the SCL pin. VDD SX8662 R_SCL SCL SCL _IN from host Figure 35 Simplified diagram of SCL SDA SDA is an IO pin that can be used as an open drain output pin with external pull-up resistor or as a high impedance input pin. The SDA IO pin is protected to VDD, using dedicated devices, in order to conform to standard I2C slave specifications. The SDA pin has diode protected to GROUND. An external pull-up resistor (1..10 kOhm) is required on this pin. Figure 36 shows the simplified diagram of the SDA pin. VDD SX8662 R_SDA SDA SDA_IN from/to host SDA_OUT Figure 36 Simplified diagram of SDA th Rev5 4 August 2011 (c) 2011 Semtech Corp. 30 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING RESETB The RESETB pin is a high impedance input pin. The RESETB pin is protected to VDD using dedicated devices. The RESETB pin has diode protected to GROUND. Figure 37 shows the simplified diagram of the RESETB pin controlled by the host. VDD SX8662 R_RESETB RESETB RESETB_IN from host Figure 37 Simplified diagram of RESETB controlled by host Figure 38 shows the RESETB without host control. VDD SX8662 RESETB RESETB_IN Figure 38 Simplified diagram of RESETB without host control th Rev5 4 August 2011 (c) 2011 Semtech Corp. 31 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 4.4 Power management pins The power management pins consist of the Power, Ground and Regulator pins. VDD VDD is a power pin and is the main power supply for the SX8662. VDD has protection to GROUND. Figure 39 shows a simplified diagram of the VDD pin. SX8662 VDD VDD Figure 39 Simplified diagram of VDD GND The SX8662 has four ground pins all named GND. These pins and the package center pad need to be connected to ground potential. The GND has protection to VDD. Figure 40 shows a simplified diagram of the GND pin. SX8662 VDD GND GND Figure 40 Simplified diagram of GND th Rev5 4 August 2011 (c) 2011 Semtech Corp. 32 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING VANA, VDIG The SX8662 has on-chip regulators for internal use (pins VANA and VDIG). VANA and VDIG have protection to VDD and to GND. The output of the regulators needs to be de-coupled with a small 100nF capacitor to ground. Figure 41 shows a simplified diagram of the VANA and VDIG pin. SX8662 VDD VDIG VDIG Cvdig GND VDD VANA VANA Cvana GND Figure 41 Simplified diagram of VANA and VDIG 4.5 General purpose IO pins The SX8662 has 8 General purpose input/output (GPIO) pins. All the GPIO pins have protection to VDD and GND. Figure 42 shows a simplified diagram of the GPIO pins. Figure 42 Simplified diagram of GPIO pins th Rev5 4 August 2011 (c) 2011 Semtech Corp. 33 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 5 DETAILED CONFIGURATION DESCRIPTIONS 5.1 Introduction The SX8662 configuration parameters are taken from the QSM or the NVM and loaded into the SPM as explained in the chapter `functional description'. This chapter describes the details of the configuration parameters of the SX8662. The SPM is split by functionality into 5 configuration sections: * General: operating modes, * Capacitive Sensors: related to lower level capacitive sensing, * Buttons (MK and PK): related to the conversion from sensor data towards button information, * Buzzer: defining parameters for the buzzer * GPIOs: related to the setup of the GPIO pins. The total address space of the SPM and the NVM is 128 bytes, from address 0x00 to address 0x7F. Two types of memory addresses, data are accessible to the user. * `application data': Application dependent data that need to be configured by the user. * `reserved': Data that need to be maintained by the user to the QSM default values (i.e. when NVM is burned). The Table 9 and Table 10 resume the complete SPM address space and show the `application data' and `reserved' addresses, the functional split and the default values (loaded from the QSM). th Rev5 4 August 2011 (c) 2011 Semtech Corp. 34 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Address Name Default/QSM value Address 0x00 Reserved 0xxx 0x20 Reserved 0x00 0x01 Reserved 0xxx 0x21 Reserved 0x00 0x02 Reserved 0x42 0x22 BtnCfg 0x30 0x03 Reserved Name Default/QSM value BtnAvgThresh 0x50 0x2B 0x24 BtnCompNegThresh 0xA0 0x05 ActiveScanPeriod 0x02 0x25 BtnCompNegCntMax 0x01 DozeScanPeriod 0x0D 0x26 BtnHysteresis 0x0A 0x06 Buttons 0x23 I2CAddress General 0xxx 0x04 PassiveTimer 0x00 0x27 BtnStuckAtTimeout 0x00 0x08 Reserved 0x00 0x28 Reserved 0x80 0x09 CapModeMisc 0x00 0x29 Reserved 0x00 0x0A Reserved 0x55 0x2A Reserved 0xFF 0x0B Reserved 0x55 0x2B Reserved 0x00 0x0C Reserved 0x55 0x2C Reserved 0x7D 0x0D CapSensitivity0_1 0x44 0x2D Reserved 0x00 0x0E CapSensitivity2_3 0x44 0x2E Reserved 0x0A 0x0F CapSensitivity4_5 0x44 0x2F Reserved 0x00 0x10 CapSensitivity6_7 0x44 0x30 Reserved 0x64 0x11 CapSensitivity8_9 0x44 0x31 Reserved 0x34 Capacitive Sensors 0x07 0x44 0x32 Reserved 0x50 0xA0 0x33 Reserved 0xA0 CapThresh1 0xA0 0x34 Reserved 0x01 CapThresh2 0xA0 0x35 Reserved 0x00 CapThresh3 0xA0 0x36 Reserved 0x00 0x17 CapThresh4 0xA0 0x37 BuzzerCfg 0xA4 0x18 CapThresh5 0xA0 0x38 BuzzerFreqPhase1 0x40 0x19 CapThresh6 0xA0 0x39 BuzzerFreqPhase2 0x20 0x1A CapThresh7 0xA0 0x3A Reserved 0x00 0x1B CapThresh8 0xA0 0x3B Reserved 0x00 0x1C CapThresh9 0xA0 0x3C Reserved 0x00 0x1D CapThresh10 0xA0 0x3D Reserved 0x00 0x1E CapThresh11 0xA0 0x3E Reserved 0x00 0x1F CapPerComp 0x00 0x3F Reserved 0x00 0x13 0x14 0x15 0x16 Buzzer CapSensitivity10_11 CapThresh0 0x12 Table 9 SPM address map: 0x00...0x3F Note * `0xxx': th write protected data Rev5 4 August 2011 (c) 2011 Semtech Corp. 35 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Address Name Default/QSM value Address Name Default/QSM value 0x00 0x60 GpioDecTime7_6 0x44 Reserved 0x00 0x61 GpioDecTime5_4 0x44 0x42 Reserved 0x00 0x62 GpioDecTime3_2 0x44 0x43 GpioMode7_4 0x00 0x63 GpioDecTime1_0 0x44 0x44 GpioMode3_0 0x00 0x64 GpioOffDelay7_6 0x00 0x45 GpioIntensityOn0 0xFF 0x65 GpioOffDelay5_4 0x00 0x46 GpioIntensityOn1 0xFF 0x66 GpioOffDelay3_2 0x00 0x47 GpioIntensityOn2 0xFF 0x67 GpioOffDelay1_0 0x00 0x48 GpioIntensityOn3 0xFF 0x68 Reserved 0x00 0x49 GpioIntensityOn4 0xFF 0x69 Reserved 0x00 0x4A GpioIntensityOn5 0xFF 0x6A Reserved 0x00 0x4B GpioIntensityOn6 0xFF 0x6B Reserved 0x00 0x4C GpioIntensityOn7 0xFF 0x6C Reserved 0x00 0x4D GpioIntensityOff0 0x00 0x6D GpioFadingMode7_4 0x00 0x4E GpioIntensityOff1 0x00 0x6E GpioFadingMode3_0 0x00 0x4F GpioIntensityOff2 0x00 0x6F Reserved 0x50 0x50 GpioIntensityOff3 0x00 0x70 Reserved 0x74 GpioIntensityOff4 0x00 0x71 Reserved 0x10 GpioIntensityOff5 0x00 0x72 Reserved 0x45 0x53 GpioIntensityOff6 0x00 0x73 Reserved 0x02 0x54 GpioIntensityOff7 0x00 0x74 Reserved 0xFF 0x55 Reserved 0xFF 0x75 Reserved 0xFF 0x56 GpioOutPwrUp 0x00 0x76 Reserved 0xFF 0x57 GpioAutoLight 0xFF 0x77 Reserved 0xD5 0x58 GpoPolarity 0x7F 0x78 Reserved 0x55 0x59 GpioFunction 0x00 0x79 Reserved 0x55 0x5A GpioIncFactor 0x00 0x7A Reserved 0x7F 0x5B GpioDecFactor 0x00 0x7B Reserved 0x23 0x5C GpioIncTime7_6 0x00 0x7C Reserved 0x22 0x5D GpioIncTime5_4 0x00 0x7D Reserved 0x41 0x5E GpioIncTime3_2 0x00 0x7E Reserved 0xFF 0x51 0x52 GpioIncTime1_0 0x5F 0x00 0x7F GPIOs Reserved 0x41 GPIOs 0x40 SpmCrc 1 0xXX Table 10 SPM address map: 0x40...0x7F 1 Note * SpmCrc: th Rev5 4 August 2011 CRC depending on SPM content, updated in Active or Doze mode. (c) 2011 Semtech Corp. 36 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 5.2 General Parameters General Parameters Address Name Bits Description 0x04 I2CAddress 7 Reserved (0) 6:0 Defines the I2C address. The I2C address will be active after a reset. Default: 0x2B 0x05 ActiveScanPeriod 7:0 Defines Active Mode Scan Period (Figure 6). 0x00: Reserved 0x01: 15ms 0x02: 30ms (default) ... 0xFF: 255 x 15ms 0x06 DozeScanPeriod 7:0 Defines Doze Mode Scan Period (Figure 6). 0x00: Reserved 0x01: 15ms ... 0x0D: 195ms (default) ... 0xFF: 255 x 15ms 0x07 PassiveTimer 7:0 Defines Passive Timer on Button Information (Figure 7). 0x00: OFF (default) 0x01: 1 second ... 0xFF: 255 seconds 0x08 Reserved 7:0 Reserved (0x00) Table 11 General Parameters th Rev5 4 August 2011 (c) 2011 Semtech Corp. 37 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 5.3 Capacitive Sensors Parameters Capacitive Sensors Parameters Address Name Bits Description 0x09 CapModeMisc 7:5 Reserved (000) 4:3 CapSenseProtect: 00: OFF (default) 01: ON. GPIOs activity is disabled during CAP11 sensing. 10: ON. GPIOs activity is disabled during CAP10-11 sensing. 11: ON. GPIOs activity is disabled during CAP0-11 sensing (i.e. all CAPx). 2:0 IndividualSensitivity Defines common sensitivity for all sensors or individual sensor sensitivity. 000: Common sensitivity settings (CapSensitivity0_1[7:4]) (default) 100: Individual sensitivity settings (CapSensitivityx_x) Else : Reserved 0x0A Reserved 7:0 Reserved (0x55) 0x0B Reserved 7:0 Reserved (0x55) 0x0C Reserved 7:0 Reserved (0x55) 0x0D CapSensitivity0_1 0x0E CapSensitivity2_3 0x0F CapSensitivity4_5 7:4 CAP0 Sensitivity - Common Sensitivity Defines the sensitivity. 0x0: Minimum 3:0 CAP1 Sensitivity 0x1: 1 ... 7:4 CAP2 Sensitivity 0x4: 4 (default) 3:0 CAP3 Sensitivity ... 0x7: Maximum 7:4 CAP4 Sensitivity 0x8..0xF: Reserved 3:0 CAP5 Sensitivity 0x10 CapSensitivity6_7 7:4 CAP6 Sensitivity 3:0 CAP7 Sensitivity 0x11 CapSensitivity8_9 7:4 CAP8 Sensitivity 3:0 CAP9 Sensitivity 0x12 CapSensitivity10_1 7:4 CAP10 Sensitivity 1 3:0 CAP11 Sensitivity 0x13 CapThresh0 7:0 CAP0 Touch Threshold 0x14 CapThresh1 7:0 CAP1 Touch Threshold 0x15 CapThresh2 7:0 CAP2 Touch Threshold 0x16 CapThresh3 7:0 CAP3 Touch Threshold 0x17 CapThresh4 7:0 CAP4 Touch Threshold 0x18 CapThresh5 7:0 CAP5 Touch Threshold 0x19 CapThresh6 7:0 CAP6 Touch Threshold 0x1A CapThresh7 7:0 CAP7 Touch Threshold 0x1B CapThresh8 7:0 CAP8 Touch Threshold 0x1C CapThresh9 7:0 CAP9 Touch Threshold 0x1D CapThresh10 7:0 CAP10 Touch Threshold 0x1E CapThresh11 7:0 CAP11 Touch Threshold 0x1F CapPerComp 7:4 Reserved (0000) th Rev5 4 August 2011 (c) 2011 Semtech Corp. 38 Defines the Touch Threshold ticks. 0x00: 0, 0x01: 4, ... 0xA0: 640 (default), ... 0xFF: 1020 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Capacitive Sensors Parameters Address Name Bits Description 3:0 Periodic Offset Compensation Defines the periodic offset compensation. 0x0: OFF (default) 0x1: 1 second 0x2: 2 seconds ... 0x7: 7 seconds 0x8: 16 seconds 0x9: 18 seconds ... 0xE: 28 seconds 0xF: 60 seconds Table 12 Capacitive Sensors Parameters CapSenseProtect If needed, ASI activity can be protected against LED interference by automatically disabling GPIOs during sensing periods. At the end of the sensing activity, GPIOs activity resume normally. CapModeMisc By default the ASI uses common sensitivity for all capacitive sensors in the case overlay material and sensors sizes are about equal. The register bits CapSensitivity0_1[7:4] determine the sensitivity for all sensors in common sensitivity mode. The ASI can use an individual sensitivity for each CAP pin The individual sensitivity mode results in longer sensing periods than required in common sensitivity mode. CapSensitivity0_1, CapSensitivity10_11 CapSensitivity2_3, CapSensitivity4_5, CapSensitivity6_7, CapSensitivity8_9, The sensitivity of the sensors can be set between 8 values. The higher the sensitivity is set the larger the value of the ticks will be. The minimum sensitivity can be used for thin overlay materials and large sensors, while the maximum sensitivity is required for thicker overlay and smaller sensors. The required sensitivity needs to be determined during a product development phase. Too low sensitivity settings result in missing touches. Too high sensitivity settings will result in fault detection of fingers hovering above the touch sensors. The sensitivity is identical for all sensors in common sensitivity mode using the bits CapSensitivity0_1[7:4] and can be set individually using register CapModeMisc[2:0]. CapThresh0, CapThresh1, CapThresh2, CapThresh3, CapThresh4, CapThresh5, CapThresh6, CapThresh7, CapThresh8, CapThresh9, CapThresh10, CapThresh11: For each CAP pin a threshold level can be set individually. The threshold levels are used by the SX8662 for making touch and release decisions. The details are explained in the sections for buttons. CapPerComp The SX8662 offers a periodic offset compensation for applications which are subject to substantial environmental changes. The periodic offset compensation is done at a defined interval and only if buttons are released. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 39 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 5.4 Buttons (MK and PK) Parameters Buttons Parameters Address Name 0x22 BtnCfg Bits Description 7 Reporting scheme: 0: report both MK and PK touches (multi MK touch is never allowed/reported) (default) 1: report first/single MK or PK touch (ignore next touch until release of the first one) 6 Priority key (PK): 0: OFF (default) 1: ON (CAP11) 5:4 Button events to be reported on NIRQ. 00 : None 01 : Touch 10 : Release 11 : Both (default) 3:2 Defines the number of samples at the scan period for determining a release of a button. 00 : no debounce, use incoming sample (default) 01 : 2 samples debounce 10 : 3 samples debounce 11 : 4 samples debounce 1:0 Defines the number of samples at the scan period for determining a touch of a button. 00 : no debounce, use incoming sample (default) 01 : 2 samples debounce 10 : 3 samples debounce 11 : 4 samples debounce 0x23 BtnAvgThresh 7:0 Defines the positive threshold for disabling the processing filter averaging. If ticks are above the threshold, then the averaging is suspended. 0x00: 0 0x01: 4 ... 0x50: 320 (default) ... 0xFF: 1020 0x24 BtnCompNegThresh 7:0 Defines the negative offset compensation threshold. 0x00: 0 0x01: 4 ... 0xA0: 640 (default) ... 0xFF: 1020 0x25 BtnCompNegCntMax 7:0 Defines the number of ticks (below the negative offset compensation threshold) which will initiate an offset compensation. 0x00: reserved 0x01: 1 sample (default) ... 0xFF: 255 samples 0x26 BtnHysteresis 7:0 Defines the button hysteresis corresponding to a percentage of the CAP thresholds (defined in Table 12). All buttons use the same hysteresis. 0x00: 0% 0x01: 1% ... 0x0A: 10% (default) ... th Rev5 4 August 2011 (c) 2011 Semtech Corp. 40 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Buttons Parameters Address Name Bits Description 0x64: 100% 0x27 BtnStuckAtTimeout 7:0 Defines the stuck at timeout for buttons. 0x00: OFF (default) 0x01: 1 second ... 0xFF: 255 seconds Table 13 Button Parameters ticks_diff A reliable button operation requires a coherent setting of the registers. Figure 43 shows an example of a touch and a release. The ticks will vary slightly around the zero idle state. When the touch occurs the ticks will rise sharply. At the release of the button the ticks will go down rapidly and converge to the idle zero value. Figure 43 Touch and Release Example As soon as the ticks become larger than the CAP thresholds (see registers of the previous section) plus the hysteresis (defined in register BtnHysteresis ) the debounce counter starts. In the example of Figure 43 the touch is validated after 2 ticks (BtnCfg [2:0] = 1). The release is detected immediately (BtnCfg [3] = 0) at the first tick which is below the threshold minus the hysteresis. BtnCfg The user can select to have the interrupt signal (INTB) on touching a button, releasing a button or both. In noisy environments it may be required to debounce the touch and release detection decision. In case the debounce is enabled the SX8662 will count up to the number of debounce samples BtnCfg [1:0], BtnCfg [3:2] before taking a touch or release decision. The sample period is identical to the scan period. BtnAvgPosThresh Small environmental and system noise cause the ticks to vary slowly around the zero idle mode value. In case the ticks get slightly positive this is considered as normal operation. Very large positive tick values indicate a valid touch. The averaging filter is disabled as soon as the average reaches the value defined by th Rev5 4 August 2011 (c) 2011 Semtech Corp. 41 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING BtnAvgPosThresh. This mechanism avoids that a valid touch will be averaged and finally the tick difference becomes zero. In case three or more sensors reach the BtnAvgPosThresh value simultaneously then the SX8662 will start an offset compensation procedure. ticks_avg Small environmental and system noise cause the ticks to vary slowly around the zero idle mode value. In case the ticks get slightly negative this is considered as normal operation. However large negative values will trigger an offset compensation phase and a new set of DCVs will be obtained. The decision to trigger a compensation phase based on negative ticks is determined by the value in the register BtnCompNegThresh and by the number of ticks below the negative thresholds defined in register BtnCompNegCntMax. An example is shown in Figure 44. Figure 44 Negative Ticks Offset Compensation Trigger BtnCompNegThresh Small negative ticks are considered as normal operation and will occur very often. Larger negative ticks however need to be avoided and a convenient method is to trigger an offset compensation phase. The new set of DCV will assure the idle ticks will be close to zero again. A trade-off has to be found for the value of this register. A negative threshold too close to zero will trigger a compensation phase very often. A very negative threshold will never trigger. BtnCompNegCntMax As soon as the ticks get smaller than the Negative Threshold the Negative Counter starts to count. If the counter goes beyond the Negative Counter Max then the offset compensation phase is triggered. The recommended value for this register is `1' which means that the offset compensation starts on the first tick below the negative threshold. BtnHysteresis The hysteresis percentage is identical for all buttons. A touch is detected if the ticks are getting larger as the value defined by: CapThreshold + CapThreshold * hysteresis. A release is detected if the ticks are getting smaller as the value defined by: CapThreshold - CapThreshold * hysteresis. BtnStuckAtTimeout The stuckat timer can avoid sticky buttons. If the stuckat timer is set to one second then the touch of a finger will last only for one second and then a compensation will be performed and button hence considered released, even if the finger remains on the button for a longer time. After the actual finger release the button can be touched again and will be reported as usual. In case the stuckat timer is not required it can be set to zero. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 42 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 5.5 Buzzer Parameters Buzzer Parameters Address Name Bits Description 0x37 BuzzerCfg 7:6 Defines the phase 1 duration. 0x00: ~ 5ms 0x01: ~ 10ms 0x02: ~ 15ms (default) 0x03: ~ 30ms 5:4 Defines the phase 2 duration. 0x00: ~ 5ms 0x01: ~ 10ms 0x02: ~ 15ms (default) 0x03: ~ 30ms 3 Defines the buzzer idle level (BuzzerLevelIdle). 0x0: min level (0V), (default) 0x1: max level (VDD) 2:0 Defines the buzzer pwm prescaler value. Default: 0x04 0x38 BuzzerFreqPhase1 7:0 Defines the frequency for the first phase of the buzzer. freq 4MHz /(2^prescaler * BuzzerFreqPhase1) Default: 0x40 (4KHz) 0x39 BuzzerFreqPhase2 7:0 Defines the frequency for the second phase of the buzzer. freq 4MHz /(2^prescaler * BuzzerFreqPhase2) Default: 0x20 (8KHz) 0x3A Reserved 7:0 Reserved (0x00) Table 14 Buzzer Parameters The SX8662 has the ability to drive a buzzer (on GPIO7) to provide an audible indication that a button has been touched. The buzzer is driven by a square signal for approximately 30ms (default). During the first phase (15ms) the signal's frequency is default 4KHz while in the second phase (15ms) the signal's frequency default is 8KHz. The buzzer is activated only once during any button touch and is not repeated for long touches. The user can choose to enable or disable the buzzer by configuration and define the idle level, frequencies and phase durations. Figure 45 Buzzer behavior th Rev5 4 August 2011 (c) 2011 Semtech Corp. 43 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 5.6 GPIO Parameters GPIO Parameters Address Name Bits Description 0x43 GpioMode7_4 7:6 GPIO[7] Mode Defines the GPIO mode. 00: GPO 5:4 GPIO[6] Mode 01: Reserved 3:2 GPIO[5] Mode 10: Reserved 11: SPO: Buzzer for GPIO[7], 1:0 GPIO[4] Mode Reserved for GPIO[6..0] Default GPO 7:6 GPIO[3] Mode Default GPO 5:4 GPIO[2] Mode Default GPO 3:2 GPIO[1] Mode Default GPO 1:0 GPIO[0] Mode Default GPO 0x44 GpioMode3_0 Default GPO Default GPO Default GPO 0x45 GpioIntensityOn0 0x46 GpioIntensityOn1 0x47 GpioIntensityOn2 0x48 GpioIntensityOn3 7:0 Defines the ON intensity index. 0x00: 0 7:0 0x01: 1 7:0 ... 0xFF: 255 (default) 7:0 0x49 GpioIntensityOn4 7:0 0x4A GpioIntensityOn5 7:0 0x4B GpioIntensityOn6 7:0 0x4C GpioIntensityOn7 7:0 0x4D GpioIntensityOff0 0x4E GpioIntensityOff1 0x4F GpioIntensityOff2 0x50 GpioIntensityOff3 7:0 Defines the OFF intensity index. 0x00: 0 (default) 7:0 0x01: 1 7:0 ... 0xFF: 255 7:0 0x51 GpioIntensityOff4 7:0 0x52 GpioIntensityOff5 7:0 0x53 GpioIntensityOff6 7:0 0x54 GpioIntensityOff7 7:0 0x56 GpioOutPwrUp 7:0 Defines the values of GPO pins after power up i.e. default values of I2C parameters GpoCtrl. Bits corresponding to GPO pins with Autolight ON should be left to 0. Before being actually initialized GPIOs are shortly set as inputs with pull up. 0: OFF(default) 1: ON 0x57 GpioAutoLight 7:0 Enables Autolight in GPO mode. 0: OFF 1: ON (default). GPIO0-5 = MK(TSM); GPIO6 = MK(TSM) or PK if enabled 0x58 GpioPolarity 7:0 Defines the polarity of the GPO pins. SPO pins require Normal Polarity. 0: Inverted 1: Normal Default : 0x7F 0x59 GpioFunction th Rev5 4 August 2011 7:0 Defines the intensity index vs PWM pulse width function. 0: Logarithmic (default) 1: Linear (c) 2011 Semtech Corp. 44 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING GPIO Parameters Address Name Bits Description 0x5A GpioIncFactor 7:0 Defines the fading increment factor. 0: intensity index incremented every increment time (default) 1: intensity index incremented every 16 increment times 0x5B GpioDecFactor 7:0 Defines the fading decrement factor. 0: intensity index decremented every decrement time (default) 1: intensity index decremented every 16 decrement times 0x5C GpioIncTime7_6 7:4 GPIO[7] Fading Increment Time 3:0 GPIO[6] Fading Increment Time 0x5D GpioIncTime5_4 7:4 GPIO[5] Fading Increment Time 3:0 GPIO[4] Fading Increment Time 0x5E GpioIncTime3_2 7:4 GPIO[3] Fading Increment Time 3:0 GPIO[2] Fading Increment Time 0x5F GpioIncTime1_0 Defines the fading increment time. 0x0: OFF (default) 0x1: 0.5ms 0x2: 1ms ... 0xF: 7.5ms The total fading in time will be: GpioIncTime*GpioIncFactor* (GpioIntensityOn - GpioIntensityOff) 7:4 GPIO[1] Fading Increment Time 3:0 GPIO[0] Fading Increment Time 0x60 GpioDecTime7_6 7:4 GPIO[7] Fading Decrement Time 3:0 GPIO[6] Fading Decrement Time 0x61 GpioDecTime5_4 7:4 GPIO[5] Fading Decrement Time 3:0 GPIO[4] Fading Decrement Time 0x62 GpioDecTime3_2 7:4 GPIO[3] Fading Decrement Time 3:0 GPIO[2] Fading Decrement Time 0x63 GpioDecTime1_0 7:4 GPIO[1] Fading Decrement Time 3:0 GPIO[0] Fading Decrement Time 0x64 GpioOffDelay7_6 7:4 GPIO[7] OFF Delay 3:0 GPIO[6] OFF Delay 0x65 GpioOffDelay5_4 7:4 GPIO[5] OFF Delay 3:0 GPIO[4] OFF Delay 0x66 GpioOffDelay3_2 7:4 GPIO[3] OFF Delay 3:0 GPIO[2] OFF Delay 0x67 GpioOffDelay1_0 7:4 GPIO[1] OFF Delay Defines the fading decrement time. 0x0: OFF 0x1: 0.5ms 0x2: 1ms ... 0x4: 2.0ms (default) ... 0xF: 7.5ms The total fading out time will be: GpioDecTime*GpioDecFactor* (GpioIntensityOn - GpioIntensityOff) Defines the delay between release and start of fading out (single fading) 0x0: instantaneous (default) 0x1: 200 ms 0x2: 400 ms 0x3: 600ms ... 0xA: 2s 0xB: 4s ... 0xF: 12s 3:0 GPIO[0] OFF Delay 0x68 Reserved 7:0 Reserved (0x00) 0x69 Reserved 7:0 Reserved (0x00) 0x6A Reserved 7:0 Reserved (0x00) 0x6B Reserved 7:0 Reserved (0x00) 0x6C Reserved 7:0 Reserved (0x00) 0x6D GpioFadingMode7_4 7:6 Fading mode for GPIO[7] 5:4 Fading mode for GPIO[6] 3:2 Fading mode for GPIO[5] 1:0 Fading mode for GPIO[4] 0x6E GpioFadingMode3_0 th Rev5 4 August 2011 7:6 Fading mode for GPIO[3] (c) 2011 Semtech Corp. 45 Defines the Fading mode for GPO[7:0]. 00: Single (default) 01: Continuous 10: Reserved 11: Reserved www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING GPIO Parameters Address Name Bits Description 5:4 Fading mode for GPIO[2] 3:2 Fading mode for GPIO[1] 1:0 Fading mode for GPIO[0] The fading modes are expected to be defined at power up by the QSM or NVM. In case the fading modes need to be changed after power up this can be done when the GPOs are all OFF. Table 15 resumes the applicable SPM and I2C parameters for each GPIO mode. SPM I2C 1 GpioMode GpioOutPwrUp GpioAutolight GPO Autolight OFF X 1 X OFF GpioPolarity X GpioIntensityOn X GpioIntensityOff X GpioFunction GpioIncFactor GpioDecFactor GpioIncTime GpioDecTime GpioOffDelay GpioFadingMode GpoCtrl X X X X X X X X GPO Autolight ON X OFF ON TSM->Normal else X X TSM->0% else X X X X X X X X SPO (Buzzer - GPIO7 only) X OFF ON Normal Linear GpioOutPwrUp must be set to OFF in Continuous Fading Mode Grey = not applicable, with or without required setting Table 15 Applicable (X) SPM/I2C Parameters vs. GPIO Mode th Rev5 4 August 2011 (c) 2011 Semtech Corp. 46 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6 I2C INTERFACE The I2C implemented on the SX8662 is compliant with: - standard (100kb/s), fast mode (400kb/s) - slave mode - 7 bit address (default 0x2B). The default address can be changed in the NVM at address 0x04. The host can use the I2C to read and write data at any time. The effective changes will be applied at the next processing phase (section 3.2). Three types of registers are considered: - status (read). These registers give information about the status of the capacitive buttons, GPIs, operation modes etc... - control (read/write). These registers control the soft reset, operating modes, GPIOs and offset compensation. - SPM gateway (read/write). These registers are used for the communication between host and the SPM. The SPM gateway communication is done typically at power up and is not supposed to be changed when the application is running. The SPM needs to be re-stored each time the SX8662 is powered down. The SPM can be stored permanently in the NVM memory of the SX8662. The SPM gateway communication over the I2C at power up is then not required. The I2C will be able to read and write from a start address and then perform read or writes sequentially, and the address increments automatically. The supported I2C access formats are described in the next sections. 6.1 I2C Write The format of the I2C write is given in Figure 46. After the start condition [S], the slave address (SA) is sent, followed by an eighth bit (`0') indicating a Write. The SX8662 then acknowledges [A] that it is being addressed, and the master sends an 8 bit Data Byte consisting of the SX8662 Register Address (RA). The slave acknowledges [A] and the master sends the appropriate 8 bit Data Byte (WD0). Again the slave acknowledges [A]. In case the master needs to write more data, a succeeding 8 bit Data Byte will follow (WD1), acknowledged by the slave [A]. This sequence will be repeated until the master terminates the transfer with the Stop condition [P]. Figure 46 I2C write The register address is incremented automatically when successive register data (WD1...WDn) is supplied by the master. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 47 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.2 I2C read The format of the I2C read is given in Figure 47. After the start condition [S], the slave address (SA) is sent, followed by an eighth bit (`0') indicating a Write. The SX8662 then acknowledges [A] that it is being addressed, and the master responds with an 8 bit data consisting of the Register Address (RA). The slave acknowledges [A] and the master sends the Repeated Start Condition [Sr]. Once again, the slave address (SA) is sent, followed by an eighth bit (`1') indicating a Read. The SX8662 responds with acknowledge [A] and the Read Data byte (RD0). If the master needs to read more data it will acknowledge [A] and the SX8662 will send the next read byte (RD1). This sequence can be repeated until the master terminates with a NACK [N] followed by a stop [P]. Figure 47 I2C read th Rev5 4 August 2011 (c) 2011 Semtech Corp. 48 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.3 I2C Registers Overview Address Name R/W Description 0x00 IrqSrc read Interrupt Source 0x01 CapStatKeys read Cap Status 0x02 Reserved 0x03 Reserved 0x04 Reserved 0x05 Reserved 0x06 Reserved 0x07 Reserved 0x08 SpmStat read SPM Status 0x09 CompOpMode read/write Compensation and Operating Mode 0x0A GpoCtrl 0x0B Reserved 0x0C Reserved 0x0D SpmCfg read/write SPM Configuration 0x0E SpmBaseAddr read/write SPM Base Address 0x0F Reserved 0xAC SpmKeyMsb read/write SPM Key MSB 0xAD SpmKeyLsb read/write SPM Key LSB 0xB1 SoftReset read/write Software Reset Table 16 I2C Registers Overview th Rev5 4 August 2011 (c) 2011 Semtech Corp. 49 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.4 Status Registers Address 0x00 Name Bits Description 7 Reserved 6 NVM burn interrupt flag 5 SPM write interrupt flag 4 Reserved 3 Reserved 2 Sensors interrupt flag 1 Compensation interrupt flag 0 Operating Mode interrupt flag IrqSrc Interrupt source flags 0: Inactive (default) 1: Active INTB goes low if any of these bits is set. More than one bit can be set. Reading IrqSrc clears it together with INTB. Table 17 Interrupt Source The delay between the actual event and the flags indicating the interrupt source may be one scan period. IrqSrc[6] is set once NVM burn procedure is completed. IrqSrc[5] is set once SPM write is effective. IrqSrc[2] is set if a sensor event occurred. CapStatKeys show the detailed status of the sensors. IrqSrc[1] is set once compensation procedure is completed either through automatic trigger or via host request. IrqSrc[0] is set when actually entering Active or Doze mode via host request. CompOpmode shows the current operation mode. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 50 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Address Name Bits Description 7 0x01 CapStatKeys Reserved Priority Key Status 6 0 : not touched. 1 : touched. Matrix Keys Status 0x00: no touch on matrix 0x01: key1 (MK1) is touched 0x02: key2 (MK2) is touched 5:0 ... 0x24: key36 (MK36) is touched If several matrix buttons are touched only the first one is reported. Cf figure below for MK mapping/numbering vs CAPx pins Table 18 I2C Cap status Figure 48 Matrix Keys Mapping Address 0x08 Name Bits SpmStat 7:4 3 th Rev5 4 August 2011 Description reserved NvmValid Indicates if the current NVM is valid. 0: No - QSM is used 1: Yes - NVM is used (c) 2011 Semtech Corp. 51 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING Address Name Bits Description 2:0 Indicates the number of times NVM has been burned: 0: None - QSM is used (default) 1: Once - NVM is used if NvmValid = 1, else QSM. NvmCount 2: Twice - NVM is used if NvmValid = 1, else QSM. 3: Three times - NVM is used if NvmValid = 1, else QSM. 4: More than three times - QSM is used Table 19 I2C SPM status 6.5 Control Registers Address Name Bits Description 7:3 Reserved*, write only `00000' 2 0x09 Compensation Indicates/triggers compensation procedure 0: Compensation completed (default) 1: read -> compensation running ; write -> trigger compensation Operating Mode Indicates/programs** operating mode 00: Active mode (default) 01: Doze mode 10: Sleep mode 11: Reserved CompOpMode 1:0 * The reading of these reserved bits will return varying values. ** After the operating mode change (Active/Doze) the host should wait for INTB or 300ms before performing any I2C read access. Table 20 I2C compensation, operation modes Address Name 0x0A GpoCtrl Bits 7:0 Description GpoCtrl[7:0] Triggers ON/OFF state of GPOs when Autolight is OFF 0: OFF (i.e. go to IntensityOff) 1: ON (i.e. go to IntensityOn) Default is set by SPM parameter GpioOutPwrUp Bits of non-GPO pins are ignored. Table 21 I2C GPO Control Address 0xB1 Name Bits Description SoftReset 7:0 Writing 0xDE followed by 0x00 will reset the chip. Table 22 I2C Soft Reset th Rev5 4 August 2011 (c) 2011 Semtech Corp. 52 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.6 SPM Gateway Registers The SX8662 I2C interface offers two registers for exchanging the SPM data with the host. * SpmCfg * SpmBaseAddr Address 0x0D Name Bits Description 7:6 00: Reserved 5:4 Defines the normal operation or SPM mode 00: I2C in normal operation mode (default) 01: I2C in SPM mode 10: Reserved 11: Reserved 3 Defines r/w direction of SPM 0: SPM write access (default) 1: SPM read access 2:0 000: Reserved SpmCfg Table 23 SPM access configuration Address Name Bits Description 0x0E SpmBaseAddr 7:0 SPM Base Address (modulo 8). The lowest address is 0x00 (default) The highest address is 0x78. Table 24 SPM Base Address The exchange of data, read and write, between the host and the SPM is always done in bursts of eight bytes. The base address of each burst of eight bytes is a modulo 8 number, starting at 0x00 and ending at 0x78. The registers SpmKeyMsb and SpmKeyLsb are required for NVM programming as described in section 6.7. Address 0xAC Name Bits Description SpmKeyMsb 7:0 SPM to NVM burn Key MSB Unlock requires writing data: 0x62 Table 25 SPM Key MSB at I2C register address 0xAC Address 0xAD Name Bits Description SpmKeyLsb 7:0 SPM to NVM burn Key LSB Unlock requires writing data: 0x9D Table 26 SPM Key LSB th Rev5 4 August 2011 (c) 2011 Semtech Corp. 53 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.6.1 SPM Write Sequence The SPM must always be written in blocks of 8 bytes. The sequence is described below: 1. Set the I2C in SPM mode by writing "01" to SpmCfg[5:4] and SPM write access by writing `0' to SpmCfg[3]. 2. Write the SPM base address to SpmBaseAddr (The base address needs to be a value modulo 8). 3. Write the eight consecutive bytes to I2C address 0, 1, 2, ...7 4. Terminate by writing "000" to SpmCfg[5:3]. Figure 49 SPM write sequence The complete SPM can be written by repeating 16 times the cycles shown in Figure 49 using base addresses 0x00, 0x08, 0x10,...0x70, 0x78. Once the SPM write sequence is actually applied, the INTB pin will be asserted. The host clears the interrupt by reading any I2C register. At the same time the bit GenStatMsb[6], indicating the SPM write is done, will be cleared. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 54 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.6.2 SPM Read Sequence The SPM must always be read in blocks of 8 bytes. The sequence is described below: 1. Set the I2C in SPM mode by writing "01" to SpmCfg[5:4] and SPM read access by writing `1' to SpmCfg[3]. 2. Write the SPM base address to SpmBaseAddr (The base address needs to be a value modulo 8). 3. Read the eight consecutive bytes from I2C address 0, 1, 2, ...7 4. Terminate by writing "000" to SpmCfg[5:3]. Figure 50 SPM Read Sequence The complete SPM can be read by repeating 16 times the cycles shown in Figure 50 using base addresses 0x00, 0x08, 0x10,...0x70, 0x78. Once the SPM read sequence is actually applied, the INTB pin will be asserted. The host clears the interrupt by reading any I2C register. At the same time the bit GenStatMsb[6], indicating the SPM write is done, will be cleared. th Rev5 4 August 2011 (c) 2011 Semtech Corp. 55 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 6.7 NVM burn The content of the SPM can be copied permanently (burned) into the NVM to be used as the new default parameters. The burning of the NVM can be done up to three times and must be done only when the SPM is completely written with the desired data. The number of times the NVM has been burned can be monitored by reading NvmCycle from the I2C register GenStatLsb[7:5]. Figure 51 Simplified Diagram NvmCycle Figure 51 shows the simplified diagram of the NvmCycle counter. The SX8662 is delivered with empty NVM and NvmCycle set to zero. The SPM points to the QSM. Each NVM burn will increase the NvmCycle. At the fourth NVM burn the SX8662 switches definitely to the QSM. The burning of the SPM into the NVM is done by executing a special sequence of four I2C commands. 1. Write the data 0x62 to the I2C register I2CKeyMsb. 2. Write the data 0x9D to the I2C register I2CKeyLsb. 3. Write the data 0xA5 to the I2C register I2CSpmBaseAddr. 4. Write the data 0x5A to the I2C register I2CSpmBaseAddr. Terminate the I2C write by a STOP. Terminate the I2C write by a STOP. Terminate the I2C write by a STOP. Terminate the I2C write by a STOP. This is illustrated in Figure 52. 1) S SA 0 A 0xAC A 0x62 A P 2) S SA 0 A 0xAD A 0x9D A P 3) S SA 0 A 0x0E A 0xA5 A P 4) S SA 0 A 0x0E A 0x5A A P S SA A P : Start condition : Slave address : Slave acknowledge : Stop condition From master to slave From slave to master Figure 52: NVM burn procedure th Rev5 4 August 2011 (c) 2011 Semtech Corp. 56 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 7 APPLICATION INFORMATION A typical application schematic is shown in figure below. buzzer SX8662 cap2 analog sensor interface clock generation RC PWM LED controller gpio6 cap4 cap9 gnd gpio5 cap5 power management gpio4 cap7 cap6 cap6 micro processor GPIO controller cap7 gpio3 gpio2 cap8 RAM NVM ROM I2C 36 Matrix LEDs cap3 cap11 gpio7 vdig gnd vana cap1 cap10 cap8 cap3 cap2 cap1 cap0 36 Capacitive Matrix Buttons resetb cap0 gpio1 cap5 gpio0 cap9 bottom plate sda scl intb vdd cp cn cap10 cap11 cap4 HOST Figure 53 Typical Application th Rev5 4 August 2011 (c) 2011 Semtech Corp. 57 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 8 REFERENCES [1] Capacitive Touch Sensing Layout guidelines on www.semtech.com th Rev5 4 August 2011 (c) 2011 Semtech Corp. 58 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING 9 PACKAGING INFORMATION 9.1 Package Outline Drawing SX8662 is assembled in a MLPQ-W32 package as shown in figure below Figure 54 Package Outline Drawing 9.2 Land Pattern The land pattern of MLPQ-W32 package, 5 mm x 5 mm is shown in figure below. Figure 55 Land Pattern th Rev5 4 August 2011 (c) 2011 Semtech Corp. 59 www.semtech.com SX8662 Capacitive Button Matrix (up to 36) Controller with Individual LED Drivers and Buzzer Output ADVANCED COMMUNICATIONS & SENSING (c) Semtech 2011 All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. Semtech assumes no responsibility or liability whatsoever for any failure or unexpected operation resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified range. SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER'S OWN RISK. Should a customer purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages and attorney fees which could arise. Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. Contact Information Semtech Corporation Advanced Communications and Sensing Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805) 498-2111 Fax: (805) 498-3804 th Rev5 4 August 2011 (c) 2011 Semtech Corp. 60 www.semtech.com