NSVS999 Apr. 2013
Application
GPS L5
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
(Operating Temperature Range : -30~+85ºC)
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table 1. Electrical Specifications
Item Spec. Typical
Input and Output Impedance - 50Ω
Nominal Center Frequency (f0) - 1176.45MHz
Insertion Loss 1166.45~1186.45MHz 3.5dB max. 3.0dB
Response Variation 1166.45~1186.45MHz 1.5dB max. 1.0dB
Input and Output VSWR 1166.45~1186.45MHz 1.5 max. 2.0
1121.45MHz 30dB min. 40dB
Out of Band Rejection
(Relative to
Through Level) 1231.45MHz 30dB min. 35dB
Table2. Maximum Ratings
Item Rating
Maximum Input Power +10dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -30~+85ºC
Storage Temperature -40~+90ºC
NewJRC SAW FILTER
NSVS999
http://www.njr.co.jp/products/device/index.html (Japanese)
http://www.njr.com/products/device/index.html (English)
NSVS999 Apr. 2013
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
1-9--- 0
10-19--- 1
20-31--- 2
(2) Part Number Mark
Pin no. Connection
1 GND
2 IN/OUT
3 GND
4 GND
5 OUT/IN
6 GND
(0.6)
(0.25)
(0.6)
(0.53)
(0.75)
(0.45)
1
2
34
6
1.15±0.15
3. 0±0. 15
3. 0±0. 15
(a)
(1)
(b)
(2)
(1.80)
5
[2x]
[4x]
[4x]
(c)
OP
Fig.1 Measuring circuit
Fig.2 Package dimensions (in mm)
Fig.3 Desirable land area (in mm)
221
IN
50Ω OUT
50Ω
0.93
0.6
0.93 3.8
3.8
2.2 1.15
1.15
1
2
34
5
6
SAW
NSVS999 Apr. 2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -30ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of so ldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply st atic electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
New Japan Radio Co.,Ltd.
0
10
20
30
40
50
S21
Insertion Loss [dB]
0
2
4
6
8
10
CH1 : center 1176.45 span 200
CH2 : center 1176.45 span 200
Insertion Loss [dB]
FREQUENCY CHARACTERISTICS
NSVS999 Apr. 2013
S11 S22
S11 S22
1 1
3 3
5 5
7 7
9 9
11 11
1076.5 1076.5 1276.5 1276.5
Frequency [MHz] Frequency [MHz]
VSWR
VSWR
InsertionLoss [dB]
0
20
40
60
80
100
0 3000
S21
Frequency [MHz]
