0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector FH64MA Series A thoroughly space-saving design with a super low profile, a narrow pitch and a narrow depth 0.25x (n umber of pos.- 1)+2.2 mm 3.15mm Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. 0.5mm Fig.1 Smooth FPC insertion Features 1. Super low profile, top contact This top contact connector has a very thin structure with an overall connector height of 0.5mm. (Fig.1) Mating guide 2. Space-saving design A thorough space-saving design on a 0.25mm pitch, 3.15mm depth (Locked status of actuator) produces a thorough space-saving function. (Fig.1) Matingguidessurelyalign FPCinspiteofinsertionfrom theobliqueupperdirection! Fig.2 3. Smooth FPC insertion Mating guide on the connector allows for smooth FPC insertion in spite of the super low profile. (Fig.2) 4. High FPC retention force The notches on both sides of FPC are held by metal tabs, generating a high FPC retention force in spite of the small size. (Fig.3) 5. Easy-to-manufacture FPC in spite of the narrow pitch In spite of the narrow pitch of P=0.25mm, similar pull-out deviation tolerance of P=0.3mm creates the narrow pitch without increasing the cost. (Fig.4) 6. Detects unmated FPC by means of the proprietary mechanism. High FPC retention force Metallockingarms preventsFPCtofall-off!! Fig.3 General tolerance of FPC Pull-out deviation Xmm Correct FPC insertion can be checked with FPC pattern and mis-insertion can be detected. (Fig.5) 7. Halogen free *AS defined by IEC 61249-2-21. Br : 900ppm max, Cl : 900ppm max, Br+Cl : 1,500ppm max Pitch Pull-out deviation X FPC cost 0.3mm 0.07mm 0.25mm 0.07mm 0.2mm 0.05mm *The FPC cost is an example image. Fig.4 FPC mis-mating detected Fig.5 In cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2017.2 1 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Product Specifications Current rating 0.2A Operating Temperature Range -55 to +85C (Note 1) Storage Temperature Range -10 to +50C (Note 2) AC/DC Relative humidity 90% RH Relative humidity 90% RH Voltage rating Operating Humidity Range Storage Humidity Range 30Vrms or less (no condensation) or less (no condensation) Rating Recommended FPC SPC Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. Items 1. Insulation Resistance 2. Withstanding Voltage 3. Contact Resistance t=0.120.02 Gold plated Specifications Conditions 50Mo min 100V DC No flashover or insulation breakdown 90Vrms AC/1min 200mo max *Including FPC conductor resistance 1mA AC 4. Mechanical Operation Contact resistance : 200mo max No damages, cracks and looseness of parts 10 times insertions and extractions. 5. Vibration Resistance Contact resistance : 200mo max No damages, cracks and looseness of parts Frequency : 10 to 55Hz, half amplitude : 0.75mm, for 10 cycles in 3 axial directions. 6. Shock Resistance No electrical discontinuity of 1s or longer Contact resistance : 200mo max No damages, cracks and looseness of parts Acceleration : 981m/s2, duration 6ms, half-sine wave, at 3 times in 3 axial directions 7. Moisture Resistance in steady state Contact resistance : 200mo max Insulation resistance : 50Mo min No damages, cracks and looseness of parts 96 hours at 40c and humidity of 90 to 95% 8. Temperature Cycles Contact resistance : 200mo max Insulation resistance : 50Mo min No damages, cracks and looseness of parts Temperature : -55+15 to +35+85+15 to +35c Time : 30 2 to 3 30 2 to 3minutes 5 cycles with above conditions 9. Resistance to Soldering Heat No deformation of case or excessive looseness of the terminals Reflow : See recommended temperature profile (page 6) Manual soldering : 35010C, 5seconds Note 1 : Including temperature rise caused by current flow. Note 2 : The term "storage" refers to the long-term storage condition of unused products before PCB mounting. For no-electrification state after PCB mounting, the operating temperature and humidity are applied. Materials / Finish Parts Insulator Contact Metal fitting Material Finish/Color LCP PA Phosphor bronze Phosphor bronze Beige Black Nickel barrier gold plated Pure tin reflow plated UL Regulation UL94V-0 Product Number Structure Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders. FH 64MA - 11S - 0.25 SHW (99) Series Name : FH Series No. : 64MA Terminal Type SHW...SMT horizontal staggered mounting type No. of Contacts : 11 Specifications Contact Pitch : 0.25mm 2 None : Regular(5000 pcs/reel) (99) : 500 pcs/reel FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Connector Dimensions A0.15 B0.15 (0.07) 0.140.15 0.30.1 Contact No.1 Cavity No. HRS mark Polarization mark ) (9 0 2.920.1 (3.15 : Actuator close) (1.165) (1) (0.45) 2.150.15 Contact point 7 Contact point (0.18) (1.2) (0.1) D0.15 No. of contacts Contact No.2 0.50.05 Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. (0.25) 0.50.1 a Lot No. 1.4550.1(Vacuum pick up area) 2.670.1 a-a 0.330.1 (0.12) C0.15 0.50.1 (0.1) a (FPC : t=0.12) (E) Note 1 : The dimension in parentheses are for reference. 2 : Lead co-planarity including reinforced chucking metals shall be 0.1 max. 3 : To be delivered with tape and reel packages. See the packaging specifications for details. 4 : Note that preventive hole for sink mark or slit could be added for improvement. 5 : The quality remains good, even with the dark spots, which could occasionally occur on molded plastic. 6 : This product satisfies halogen free requirements defined as 900ppm maximum chlorine, 900ppm maximum bromine, and 1500ppm maximum total of chlorine and bromine. 7 Shows hook part of the chucking metal. Units : mm Part No. HRS No. No. of Contacts A B C FH64MA-7S-0.25SHW(**) 580-4610-0 ** 7 3.7 2.5 FH64MA-9S-0.25SHW(**) Under planning (Note 1) 9 4.2 3 FH64MA-11S-0.25SHW(**) 580-4612-0 ** 11 4.7 3.5 FH64MA-13S-0.25SHW(**) Under planning (Note 1) 13 5.2 4 FH64MA-15S-0.25SHW(**) 580-4608-0 ** 15 5.7 4.5 FH64MA-17S-0.25SHW(**) Under planning (Note 1) 17 6.2 5 FH64MA-19S-0.25SHW(**) Under developing (Note 1) 19 6.7 FH64MA-21S-0.25SHW(**) 21 7.2 Under planning (Note 1) D E 1.5 1 3.23 2 1.5 3.73 2.5 2 4.23 3 2.5 4.73 3.5 3 5.23 4 3.5 5.73 5.5 4.5 4 6.23 6 5 4.5 6.73 Note 1 : Contact positions without HRS No. are currently under planning and developing. Please contact hirose for detailed information about product variation. 3 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Recommended PCB Mounting Pattern C0.02 0.550.02 X ((n+1)/2)x 0.02 X 2x 0.02 X 0.250.02 0.5 0.550.02 B 0.270.02 Contact No.2 0.5 (0.25) 2.050.02 Connector image (0.05) 0.530.02 Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. 2.050.02 Contact No.1 ((n-1)/2)x 0.02 X 0.250.02 D Recommended Stencil Pattern B 0.250.01 (Land pattern image) 0.5 (0.16) 0.410.01 2.360.01 0.5 ((n+1)/2)x 0.02 Y 2x 0.02 Y 0.440.01 0.440.01 0.230.01 2.360.01 C0.02 (0.25) 0.230.01 ((n-1)/2)x 0.02 Y D Note 8 : 'n' shows the number of contacts. Units : mm Part No. HRS No. No. of Contacts B C D FH64MA-7S-0.25SHW(**) FH64MA-9S-0.25SHW(**) FH64MA-11S-0.25SHW(**) FH64MA-13S-0.25SHW(**) FH64MA-15S-0.25SHW(**) FH64MA-17S-0.25SHW(**) FH64MA-19S-0.25SHW(**) FH64MA-21S-0.25SHW(**) 580-4610-0 ** Under planning (Note 1) 580-4612-0 ** Under planning (Note 1) 580-4608-0 ** Under planning (Note 1) Under developing (Note 1) Under planning (Note 1) 7 9 11 13 15 17 19 21 2.5 3 3.5 4 4.5 5 5.5 6 1.5 2 2.5 3 3.5 4 4.5 5 1 1.5 2 2.5 3 3.5 4 4.5 Note 1 : Contact positions without HRS No. are currently under planning and developing. Please contact hirose for detailed information about product variation. 4 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector ((n+1)/2)x 0.02 Z Contact No.1 12 5) 0.0 (R .1) 0 (R 0.240.03 9 0.10.02 9 0.10.02 9 0.070.02 0.070.02 .1 0.1 .1 0.1 R0 0.120.02 10 H 0.3450.02 9 0.10.02 (0.07) R0 R0 R 12 .1 0.1 .15 0.1 0.1 0.1 Contact No.2 R0 Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. 0.970.05 0.580.05 0.25 Z 0.850.07 2.630.3 (Stiffener) 0.850.07 F0.05 C0.02 0.130.1 0.430.1 0.510.1 0.610.1 1.1150.1 1.170.1 1.270.1 1.630.3 (Exposed conductor) Recommended FPC Dimensions 0.10.02 0.10.02 ((n-1)/2)x 0.02 Z 0.240.03 0.250.02 D G0.05 11 F0.05 Note 9 10 11 12 Shows recommended dimensions when lead for plating is required. Dimension H must be 0.5mm minimum. Indicated tolerance is applicable to the exposed conductor. Both end sides of contact pad on FPC cannot be used for signal transmission. Units : mm Part No. HRS No. No. of Contacts C D F G FH64MA-7S-0.25SHW(**) FH64MA-9S-0.25SHW(**) FH64MA-11S-0.25SHW(**) FH64MA-13S-0.25SHW(**) FH64MA-15S-0.25SHW(**) FH64MA-17S-0.25SHW(**) FH64MA-19S-0.25SHW(**) FH64MA-21S-0.25SHW(**) 580-4610-0 ** Under planning (Note 1) 580-4612-0 ** Under planning (Note 1) 580-4608-0 ** Under planning (Note 1) Under developing (Note 1) Under planning (Note 1) 7 9 11 13 15 17 19 21 1.5 2 2.5 3 3.5 4 4.5 5 1 1.5 2 2.5 3 3.5 4 4.5 3.2 3.7 4.2 4.7 5.2 5.7 6.2 6.7 2.18 2.68 3.18 3.68 4.18 4.68 5.18 5.68 Note 1 : Contact positions without HRS No. are currently under planning and developing. Please contact hirose for detailed information about product variation. FPC Configuration (Reference example) MATERIAL NAME Covering film layer Cover adhesive Surface treatment Copper foil Base adhesive Base film Reinforcement material adhesive Stiffener MATERIAL THICKNESS (m) Polyimide 1mil 25 25 1m to 6m nickel underplated 0.2m gold plated (4) Cu 1/2oz 18 Heat-hardened adhesive No adhesion material Polyimide 1mil 25 Heat-hardened adhesive 30 Polyimide 2mil 50 5 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Packaging Specifications Embossed Carrier Tape Dimensions O1 0.1 0 Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. J K0.1 .5 40.1 (2) CL +0.2 _0.1 (1.35) (0.3) 1.750.1 Direction of unreeling 80.1 Reel Dimensions Leader, Trailer Dimensions (O1 3) LReelinnerwidth Directionofunreeling Directionofunreeling (O380) (O80) 400mmMIN Leader Embossedcarriertape 100mmMIN emptycomponents 160mmMIN Trailer,emptycomponents Topcovertape MReelouterwidth Units : mm HRS No. No. of Contacts J K L M FH64MA-7S-0.25SHW(**) FH64MA-9S-0.25SHW(**) Part No. 580-4610-0 ** Under planning (Note 1) 7 9 16 16 7.5 7.5 17.4 17.4 21.4 21.4 FH64MA-11S-0.25SHW(**) FH64MA-13S-0.25SHW(**) FH64MA-15S-0.25SHW(**) FH64MA-17S-0.25SHW(**) FH64MA-19S-0.25SHW(**) FH64MA-21S-0.25SHW(**) 580-4612-0 ** Under planning (Note 1) 580-4608-0 ** Under planning (Note 1) Under developing (Note 1) Under planning (Note 1) 11 13 15 17 19 21 16 16 16 16 16 24 7.5 7.5 7.5 7.5 7.5 11.5 17.4 17.4 17.4 17.4 17.4 25.4 21.4 21.4 21.4 21.4 21.4 29.4 Note 1 : Contact positions without HRS No. are currently under planning and developing. Please contact hirose for detailed information about product variation. Temperature Profile MAX250 Temperature 245 200 180 150 150 100 20 to 40 sec. 50 25 0 6 Start 1205 sec. Preheating time Peak temperature 60 to 90 sec. Soldering time Timesec. Applicable Conditions Reflow method : IR/Hot air 220 Reflow environment : Room air Solder : Paste type Sn/3.0Ag/0.5Cu (M705-GRN360-K2-V made by Senju Metal Industry Co.) Test PCB : PCB material and size Glass epoxy 32.85x15.7x1mm Land size, per recommended on page 4. Metal mask : Thickness and opening size Per recommended on page 4. This temperature profile is based on the above conditions. It may vastly depending on solder paste type, manufacturer, PCB size and mounting materials. Please use only after checking the mounting conditions. FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Operation Methods of Connectors and Precautions [Operation method] As this connector is a small-sized, thin product, care needs to be taken when handling. Check the following before use. 1. Initially delivered state The actuator is delivered in the open state, It does not need to operated before inserting FPC. [Caution] Do not close the actuator while FPC is not inserted. If the actuator is closed without the FPC inserted, the FPC insertion force could increase due to the narrower contact gap. Do not operate the connector while it is not mounted on the board. Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. 2. How to insert FPC Insert FPC to the end placed horizontal to the board surface. (Example 1) [Caution] Do not insert FPC while the actuator is closed. (Example 2) When FPC is inserted, do not move it in vertical, lateral or diagonal directions. OK (Example 1) NG (Example 2) Actuator [Open] Actuator [Closed] PCB PCB Correct operation Incorrect operation 3. Check the inserted state of FPC When FPC is completely inserted, visually inspect the inserted status of FPC. (Example 3) [Caution] FPC is not inserted deep enough or in a diagonal direction. (Example 4)(Example 5) (Example 3) OK (Example 4) (Example 5) NG NG FPC [diagonal] FPC (shallow) Correct operation Insulation case Insulation case Incorrect operation Incorrect operation Metal locking guide of FPC is hidden in the insulated case. Metal locking guide of FPC is visible from the insulated case. Insulation case Metal locking guide of FPC is visible from the insulated case. 7 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Operation Methods of Connectors and Precautions [Operation method] 4. Actuator locking mechanism Actuator rotates around the actuator rotation axis. After inserting FPC, operate the actuator rotating 90. [Caution] Operate the actuator around the center when locked. (Example 6) Do not operate the actuator on one side only when locked. (Example 7) Do not operate the actuator by pushing in the vertical direction. (Example 8) Do not apply excessive force to the housing during operation. (Example 9) (Example 6) (Example 7) Operate the actuator on one side. Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. Operate the actuator around the center. NG OK Correct operation (Example 8) Incorrect operation (Example 9) Apply an excessive force to the housing. Actuator NG NG PCB Incorrect operation Incorrect operation 5. How to unlock the actuator Push the actuator up slowly and release the lock. (Example 10) [Caution] Operate the actuator around the center when unlocked. (Example 11) Do not operate the actuator on one side only when unlocked. (Example 12) The actuator cannot be opened to over 90, Do not open it over this angle. (Example 13) This connector adopts a back-flip design, and there is difference between the FPC insertion direction and the direction of the actuator. Do not try to open FPC from its insertion side. (Example 14) (Example 10) OK Actuator Actuator PCB PCB (Example 11) (Example 12) Correct operation Operate the actuator on one side. Operate the actuator around the center. NG OK Correct operation (Example 13) (Example 14) Actuator NG PCB Incorrect operation 8 Incorrect operation A load is applied to the actuator in the opposite direction. PCB Incorrect operation NG FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Operation Methods of Connectors and Precautions [Operation method] 6. How to remove FPC After releasing the actuator lock , remove the FPC in the horizontal direction. (Example 15) [Caution] When pulling out FPC, don't apply load in the upward or lateral direction. (Example 16) Don't pull out FPC while the actuator is locked. (Example 17) (Example 15) Actuator [Open] OK (Example 16) NG Actuator [Open] Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. FPC [diagonal] PCB PCB Correct operation (Example 17) Incorrect operation NG Actuator [Closed] PCB Incorrect operation 7. Routing of FPC Depending on the routing of FPC to mate, a load may be applied to the connector, which could lead to a failure. In order to prevent failure, please consider the following concerning the mechanism design. [Caution] When routing FPC, please be careful that FPC is not pulled and routing is carried out with a margin. Please check that the stiffener is placed horizontal to the board surface. (Example 18) Please insure there is no load is applied to the connector in the pulling, inserting or lateral direction. (Example 19)(Example 20) When routing the FPC , carry out the routing operation in a manner that no direct load is applied to the connector. Please take some caution such as to fix FPC etc. (Example 19) Don't place any parts under the FPC that will interfere with FPC. (Example 21) (Example 18) OK (Example 19) The state where a load is applied to FPC NG Stiffener PCB (Example 20) Stiffener NG PCB (Example 21) Stiffener NG Parts interfering with FPC The state where a load is applied to FPC PCB 9 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector [Cautions when Mounting PCB] Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. SWarp of PCB Minimize warp of the PCB as much as possible. Lead co-planarity including reinforced metals is 0.1mm or less. Too much wrap of the PCB may result in a soldering failure. SFlexible board design Please make sure to put a stiffener on the backside of the flexible board. We recommend a glass epoxy material with the thickness of 0.3mm MIN. SLoad to Connector Do not add 0.5N or greater external force when unreel or pick and place the connector etc, or it may get broken. In addition, do not insert the FPC or operate the connector before mounting. Connector SLoad to PCB * Splitting a large PCB into several pieces * Screwing the PCB Avoid the handling described above so that no force is exerted on the PCB during the assembly process. Otherwise, the connector may become defective. SInstructions on manual soldering Follow the instructions shown below when soldering the connector manually during work, etc. FPC (For connectormounting) qDo not perform manual soldering with the FPC inserted into the connector. wDo not heat the connector excessively. Be very careful not to let the soldering iron contact any parts other than connector leads. Otherwise, the connector may be deformed or melt. eDo not supply excessive solder (or flux). If excessive solder (or flux) is supplied on the terminals, solder or flux may adhere to the contacts or rotating parts of the actuator, resulting in poor contact or a rotation failure of the actuator. Supplying excessive solder to the chucking metals may hinder actuator rotation, resulting in breakage of the connector. 10 FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. MEMO 11 Jan.1.2021Copyright2021HIROSEELECTRICCO.,LTD.AllRightsReserved. FH64MA Series0.25mm Pitch, 0.5mm High, Top Contact, Back Flip Super Low Profile FPC Connector USA: HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS CHICAGO OFFICE 2300 Warrenville Road, Suite 150, Downers Grove, IL 60515 Phone : +1-630-282-6700 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE 2841 Junction Ave, Suite 200 San Jose, CA. 95134 Phone : +1-408-253-9640 Fax : +1-408-253-9641 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE) 17197 N. Laurel Park Drive, Suite 253, Livonia, MI 48152 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. BOSTON OFFICE 300 Brickstone Square Suite 201, Andover, MA 01810 Phone : +1-978-662-5255 THE NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH Schoenbergstr. 20, 73760 ostfildern Phone : +49-711-456002-1 Fax : +49-711-456002-299 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. NUREMBERG OFFICE Neumeyerstrasse 22-26, 90411 Nurnberg Phone : +49-911 32 68 89 63 Fax : +49-911 32 68 89 69 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. HANOVER OFFICE Bayernstr. 3, Haus C 30855 Langenhagen, Germany Phone : +49-511 97 82 61 30 Fax : +49-511 97 82 61 35 http://www.hirose.com/eu/ FRANCE: HIROSE ELECTRIC EUROPE B.V. PARIS OFFICE 130 Avenue Joseph Kessel, Bat E, 78960 Voisins le Bretonneux, France Phone : +33-1-85764886 Fax : +33-1-85764823 http://www.hirose.com/eu/ UNITED KINGDOM: HIROSE ELECTRIC EUROPE BV (UK BRANCH) 4 Newton Court, Kelvin Drive, Knowlhill, Milton Keynes, MK5 8NH Phone : +44-1908 202050 Fax : +44-1908 202058 http://www.hirose.com/eu/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO., LTD. 18, Enterprise Center Tower 2, 209# Gong He Road, Jing'an District, Shanghai, CHINA 200070 Phone : +86-21-6391-3355 Fax : +86-21-6391-3335 http://www.hirose.com/cn/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO.,LTD. BEIJING BRANCH A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose.com/cn/ CHINA: HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD. Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008 Phone : +86-755-8207-0851 Fax : +86-755-8207-0873 http://www.hirose.com/cn/ HONG KONG: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560 http://www.hirose.com/hk/ TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD. 103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7350 http://www.hirose.com/tw/ KOREA: HIROSE KOREA CO.,LTD. 143, Gongdan 1-daero, Siheung-si, Gyeonggi-do, 15084, Korea Phone : +82-31-496-7000 Fax : +82-31-496-7100 http://www.hirose.co.kr/ SINGAPORE: INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE HIROSE ELECTRIC SINGAPORE PTE. LTD. 03, Anson Road, #20-01, Springleaf Tower, Office NO.552, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India Singapore 079909 Phone : +91-12-660-8018 Phone : +65-6324-6113 Fax : +91-120-4804949 Fax : +65-6324-6123 http://www.hirose.com/sg/ http://www.hirose.com/sg/ INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE Unit No-403, 4th Floor, No-84, Barton Centre, Mahatma Gandhi (MG) Road, Bangalore 560 001, Karnataka, India Phone : +91-80-4120 1907 Fax : +91-80-4120 9908 http://www.hirose.com/sg/ MALAYSIA: THAILAND: PENANG REPRESENTATIVE OFFICE BANGKOK OFFICE (REPRESENTATIVE OFFICE) 73-3-1, Ideal@The One, Jalan Mahsuri, Bayan Unit 4703, 47th FL., 1 Empire Tower, South Sathorn Road, Yannawa, Sathorn, Bangkok 10120 Thailand Lepas Penang, 11950, Malaysia Phone : +66-2-686-1255 Phone : +604-648-5536 Fax : +66-2-686-3433 http://www.hirose.com/sg/ http://www.hirose.com/sg/ (R) 12 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 02/2017. Contents are subject to change without notice for the purpose of improvements.