Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 1 DA10-050 Series 10 Watts External Power Adapters Total Power: 10 Watts Input Voltage: 90-264 Vac # of Outputs: Single Special Features * Small Size 44 x 39.5 x 25 mm excluding AC pins * High Average Loading Efficiency 79% * 2-pin Input Class II * USB connector output * -10 C to +40 C Operating Temperature Range * Reinforced Insulation 3000 Vac rms * Over-voltage Protection * Over-temperature Protection * Over-current Protection * Short circuit Protection * Elegant Enclosure ID Design * European CoC v5 Tier 2 & US DoE VI Compliant * One Year Warranty * RoHS 6/6 , WEEE and REACH Compliant Safety * * * * * * * cUL/UL 60950-1 IEC/EN 60950-1 IEC 62368-1 CCC CE GS Design to meet: NOM-NYCE, SPRING, IRAM, CTick, NSW Product Descriptions The new standard 10W charger platform provides small-size, high efficiency & low cost features. It meets new European CoC v5 Tier 2 & US DoE Level VI energy saving requirements. The integrated primary side regulation chip topology provides simplified & lowcost design. It can meet extremely low standby power (< 75mW) and high average loading efficiency (>79%). The enclosure temperature rise is < 45 oC in full temperature range from -10 to 40 oC operating. Extra features include over-voltage, over-current, short-circuit and overtemperature protections. Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 2 Model Numbers Standard Input Voltage Range Output Voltage Minimum Load Maximum Load DA10-050US 90-264 Vac 5Vdc 0A 2A DA10-050CH 90-264 Vac 5Vdc 0A 2A DA10-050EU 90-264 Vac 5Vdc 0A 2A DA10-050UK 90-264 Vac 5Vdc 0A 2A Options AC Plug Configuration for Fixed Plug U.S. 2-prong US China 2-prong CH Europe 2-prong EU UK 3-prong UK Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 3 Electrical Specifications Absolute Maximum Ratings Stress in excess of those listed in the "Absolute Maximum Ratings" may cause permanent damage to the power supply. These are stress ratings only and functional operation of the unit is not implied at these or any other conditions above those given in the operational sections of this TRN. Exposure to any absolute maximum rated condition for extended periods may adversely affect the power supply's reliability. Table 1. Absolute Maximum Ratings: Parameter Model Symbol Min Typ Max Unit All models VIN,AC 90 - 264 Vac All models PO,max - - 10 W - - 3000 Vac Input Voltage AC continuous operation Maximum Output Power Isolation Voltage Input to output All models Ambient Operating Temperature All models TA -10 - +40 oC Storage Temperature All models TSTG -40 - +85 oC Humidity(non-condensing) All models 5 - 95 % Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 4 Input Specifications All parameters defined at 25 oC ambient temperature, unless other specified. Table 2. Input Specifications: Parameter Conditions Symbol Min Typ Max Unit Operating Input Voltage, AC All VIN,AC 90 - 264 Vac Input AC Frequency All fIN 47 50/60 63 Hz Input Surge Voltage 100ms. VIN,AC = 264Vac to 300Vac and back to 264Vac Max VIN,surge - - 300 Vac Maximum Input Current (IO = IO,max) VIN,AC = 115Vac IIN,max - - 300 mA No Load Input Power (VO = On, IO = 0A) VIN,AC = 115Vac / 230Vac PIN,standby - - 75 mW VIN,AC = 230Vac IO = 10% IO,max IO = 25% - 100% IO,max 70 79 - - % % VIN,AC = 264Vac ILeakage - - 100 uA Efficiency Leakage Current to earth ground Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 5 Output Specifications Table 3. Output Specifications: Parameter Condition Symbol Min Typ Max Unit Output Voltage Regulation All VO 4.75 5.00 5.25 Vdc Output Current All IO - - 2 A Measure with a 0.1uF ceramic capacitor in parallel with a 10uF tantalum capacitor, 0 to 20MHz bandwidth VO 0 - 100 mVPK-PK 50% load change, slew rate = 0.5A/uS VO 4.1 - 6.0 Vdc All TRISE - - 100 mSec VIN,AC = 115Vac IO = IO,max THold-up - 10 - mSec Output Ripple, pk-pk VO Dynamic Response Output Rise Time Hold-up Time Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 6 DA10-050CH Performance Curves Figure 1: DA10-050CH Turn-on Delay via AC mains Vin = 115Vac, Full Load: IO = 2A Ch 1: AC Mains Ch 2: VO DA10-050CH Turn-on Delay via AC mains Vin = 230Vac, Full Load: IO = 2A Ch 1: AC Mains Ch 2: VO Figure 3: DA10-050CH Hold-up Time Vin = 90Vac / 63Hz / 0 , Full Load: IO = 2A Ch 1: AC Mains Ch 2: VO Figure 4: DA10-050CH Hold-up Time Vin = 264Vac / 47Hz / 0 , Full Load: IO = 2A Ch 1: AC Mains Ch 2: VO Figure 5: Figure 6: Ch 1: VIN DA10-050CH Start up Inrush Current Vin = 264Vac, Io = 0A, Turn On Phase = 90 Ch 3: IIN Artesyn Embedded Technologies Figure 2: Ch 1: VO DA10-050CH Output Voltage Startup Vin = 90Vac, Full Load: IO = 2A Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 7 DA10-050CH Performance Curves Figure 7: Ch 2: VO DA10-050CH Transient Response - Vo Deviation (low to high) 50% to 100% load change, 1A/uS slew rate, VIN = 115Vac Ch 3: IO Efficiency (%) 82 81 80 79 78 0.5 1 1.5 Output Current (A) DA10-050CH Efficiency Curves @ 25 oC 115 Vac 230 Vac Loading: IO = 25% increment to 2A Figure 9: Artesyn Embedded Technologies 2 Figure 8: Ch 2: VO DA10-050CH Transient Response - Vo Deviation (high to low) 100% to 50% load change, 1A/uS slew rate, VIN = 115Vac Ch 3: IO Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 8 Protection Function Specification Over Voltage Protection (OVP) Over Voltage Protection is triggered when the PSU has an internal fault which results in the output rising over the regulation limit. The power supply will bounce during overvoltage and recover to normal after remove the fault condition. Parameter VO Output Overvoltage Min Nom Max Unit / / 6.5 Vdc Over Current Protection (OCP) Current Limitation at >100% output current, Hiccup mode. The DA10 series includes internal current limit circuitry to prevent damage in the event of overload or short circuit. Recovery is automatic when the overload is removed. Parameter VO Output Overcurrent Min Nom Max Unit 2 / / A Short Circuit Protection (SCP) The DA10 series will withstand a continuous short circuit with no permanent damage, applied to its output during start-up or while running. The output will recover to normal after the short-circuit is removed. Over Temperature Protection (OTP) The power supply is internally protected against over temperature conditions. When the OT circuit is activated, the power supply will latch off, requiring AC power recycling to restart the power supply with 5 seconds "off time" at least. Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 9 Mechanical Specifications Mechanical Outline - DA10-050US Note: All dimensions in mm. Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 10 Mechanical Outline - DA10-050CH Note: All dimensions in mm. Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 11 Mechanical Outline - DA10-050EU Note: All dimensions in mm. Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 12 Mechanical Outline - DA10-050UK Note: All dimensions in mm. Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 13 Environmental Specifications EMC Requirements DA10 series power supply is designed to meet the following EMC immunity specifications: Table 4. EMC Immunity Specifications: Document Description FCC Part 15 Subpart B/ EN55022, Class B Conducted and Radiated EMI Limits EN61000-3-3 Voltage Fluctuations, max 4% EN61000-4-2 Electromagnetic Compatibility (EMC) - Testing and measurement techniques - Electrostatic discharge immunity test. +/-8KV contact discharge, performance Criteria B EN61000-4-3 Electromagnetic Compatibility (EMC) - Testing and measurement techniques, Radiated, radio-frequency, electromagnetic field immunity test, Criteria A EN61000-4-4 Electromagnetic Compatibility (EMC) - Testing and measurement techniques, Electrical Fast Transient/Burst Immunity Test. +/-1KV , I/O and signal ports performance Criteria A. EN61000-4-5 Electromagnetic Compatibility (EMC) - Testing and measurement techniques. +/-1KV for DC ports performance criteria A. EN61000-4-6 EN61000-4-11 Immunity to conducted disturbances, induced by radio-frequency fields - performance criteria A Electromagnetic Compatibility (EMC) - Testing and measurement techniques : Voltage Dips and Interruptions: performance Criteria B(For 100% reduction, Criteria C). High Frequency Pulses / Rings longer than Common Mode Noise: Less than or equal to 2.0 Vpp. 250ns Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 14 Safety Certifications The DA10-050 series power supply is in compliance with the following safety requirements. Table 5. Safety Certifications Document File # Description cUL/UL 60950-1 E132002-A402-UL US and Canada Requirements Level VI Compliance 15459 US Efficiency Standards for External Power Supplies. IEC/EN 60950-1 E132002-A402-CB-1 European Requirements IEC 62368-1 DK-46911-UL Audio/video, information and communication technology equipment. CB Certificate and Report DK-49542-UL (All CENELEC Countries) CHINA CCC Approval 2015010907769437 China Requirements CE Mark 8544 LVD NOM-NYCE Mexico Approval GS GS Mark Certification SPRING PSB Spring certification IRAM Argentina IRAM certification C-Tick C-Tick mark NSW NSW Certificate Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 15 Environmental Specification Table 6. Environmental Specifications: Parameter . Condition Min Typ Max Unit Operating Ambient Temperature Natural Convection IO = IO,max 0 - 40 oC Case (Enclosure) Temperature Rise over Ambient Temperature. Natural Convection TA = 40oC - - 45 oC Electrolytic Cap. Life Expectancy VIN,AC = 115 / 230Vac IO = IO,max 1.5 - - 10 KHr MTBF VIN,AC = 115 / 230Vac IO = IO,max 1 - - 100 KHr All - - 25 dBA Acoustic Noise Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 16 Weight The PSU weight is 34 gram maximum. Artesyn Embedded Technologies Technical Reference Note Rev.07.08.16_#1.0 DA10 Series Page 17 Record of Revision and Changes Issue Date Description Originators 1.0 07.08.2016 First Issue S. Yang For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com