TNPW Vishay High Stability Thin Film Chip Resistors FEATURES Excellent overall stability at different environmental conditions 0.05 % (1000 h rated power at 70 C) Low temperature coefficient and tight tolerances ( 0.1 %; 10 ppm/K) Metal film layer on high quality ceramic SnPb termination plating, minimum 6 % Pb APPLICATIONS TNPW precision thin film flat chip resistors are the perfect choice for most fields of modern electronics where reliability and stability is of major concern. Typical applications include industrial, medical equipment, and those, which are not necessarily subject to the RoHS directive like military and avionics. Avionics Military Medical equipment Industrial equipment STANDARD ELECTRICAL SPECIFICATIONS Metric size Resistance range TNPW0402 TNPW0603 TNPW0805 TNPW1206 TNPW1210 (1) TNPW2010 TNPW2512 (1) RR 1005M RR 1608M RR 2012M RR 3216M RR 3225M RR 5025M RR 6332M 10 to 100 k 10 to 332 k 10 to 1 M Resistance tolerance 1 %; 0.5 %; 0.1 % Temperature coefficient Rated dissipation, P70 (2) Operating voltage, Umax. AC/DC 10 to 2 M 10 to 3.01 M 10 to 4.99 M 10 to 8.87 M 50 ppm/K; 25 ppm/K; 15 ppm/K; 10 ppm/K 50 ppm/K; 25 ppm/K 0.063 W 0.1 W 0.125 W 0.25 W 0.33 W 0.4 W 0.5 W 50 V 75 V 150 V 200 V 200 V 300 V 300 V Permissible film temperature, F max. 125 C (155 C) Operating temperature range - 55 C to 125 C (155 C) Thermal resistance (3) 870 K/W 550 K/W 440 K/W 220 K/W 170 K/W 140 K/W 110 K/W Uins 1 min 75 V 100 V 200 V 300 V 300 V 300 V 300 V continuous 75 V 75 V 75 V 75 V 75 V 75 V 75 V 0.3 x 10-9/h 0.3 x 10-9/h 0.3 x 10-9/h 0.3 x 10-9/h 0.3 x 10-9/h 0.3 x 10-9/h 0.3 x 10-9/h Insulation voltage: Failure rate: FITobserved Notes * TNPW 0402 without marking. (1) Size not specified in EN 140401-801. (2) Rated voltage P x R . The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. (3) Measuring conditions in accordance with EN 140401-801. Document Number: 31006 Revision: 31-Jan-12 For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 345 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW Vishay High Stability Thin Film Chip Resistors DIMENSIONS DIMENSIONS AND MASS TYPE L (mm) W (mm) H (mm) T1/T2 (mm) MASS (mg) TNPW0402 1.0 0.05 0.5 0.05 0.35 0.05 0.2 0.10 0.65 TNPW0603 1.6 0.10 0.85 0.10 0.45 0.10 0.3 0.20 2 TNPW0805 2.0 0.15 1.25 0.15 0.45 0.10 0.4 0.20 5.5 TNPW1206 3.2 0.15 1.6 0.15 0.55 0.10 0.5 0.25 10 TNPW1210 3.2 0.15 2.45 0.15 0.60 0.15 0.5 0.25 16 TNPW2010 5.0 0.15 2.5 0.15 0.60 0.15 0.6 0.25 28 TNPW2512 6.3 0.20 3.1 0.15 0.60 0.15 0.6 0.25 39 SOLDER PAD DIMENSIONS REFLOW SOLDERING TYPE WAVE SOLDERING a (mm) b (mm) l (mm) a (mm) b (mm) l (mm) TNPW0402 0.4 0.6 0.5 - - - TNPW0603 0.5 0.9 1.0 0.9 0.9 1.0 TNPW0805 0.7 1.3 1.2 0.9 1.3 1.3 TNPW1206 0.9 1.7 2.0 1.1 1.7 2.3 TNPW1210 0.9 2.5 2.0 1.1 2.5 2.3 TNPW2010 1.0 2.5 3.9 1.2 2.5 3.9 TNPW2512 1.0 3.2 5.2 1.2 3.2 5.2 TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE TCR 50 ppm/K TNPW0402 25 ppm/K TOLERANCE RESISTANCE E-SERIES 1% 10R to 100K 24; 96 0.5 % 10R to 100K 0.1 % 47R to 100K 1% 10R to 100K 0.5 % 10R to 100K 0.1 % 15 ppm/K 0.1 % 10 ppm/K 0.1 % 50 ppm/K 0.5 % 1% 0.1 % TNPW0603 1% 25 ppm/K 0.5 % 0.1 % 15 ppm/K 0.1 % 10 ppm/K 0.1 % 50 ppm/K 0.5 % 1% 0.1 % TNPW0805 1% 25 ppm/K 0.5 % 0.1 % www.vishay.com 346 15 ppm/K 0.1 % 10 ppm/K 0.1 % 47R to 100K 24; 192 24; 96 24; 192 10R to 332K 24; 96 10R to 332K 24; 192 10R to 332K 24; 96 10R to 332K 24; 192 47R to 332K 10R to 1M0 24; 96 10R to 1M0 24; 192 10R to 1M0 24; 96 10R to 1M0 24; 192 47R to 1M0 For technical questions, contact: thinfilmchip@vishay.com Document Number: 31006 Revision: 31-Jan-12 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW High Stability Thin Film Chip Resistors Vishay TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE TCR TOLERANCE 1% 0.5 % 0.1 % 1% 0.5 % 0.1 % 0.1 % 0.1 % 1% 0.5 % 0.1 % 1% 0.5 % 0.1 % 0.1 % 0.1 % 1% 0.5 % 0.1 % 1% 0.5 % 0.1 % 1% 0.5 % 0.1 % 1% 0.5 % 0.1 % 50 ppm/K TNPW1206 25 ppm/K 15 ppm/K 10 ppm/K 50 ppm/K TNPW1210 25 ppm/K 15 ppm/K 10 ppm/K 50 ppm/K TNPW2010 25 ppm/K 50 ppm/K TNPW2512 25 ppm/K RESISTANCE 10R to 2M0 E-SERIES 24; 96 10R to 2M0 24; 192 10R to 2M0 24; 96 10R to 2M0 24; 192 47R to 2M0 10R to 3M01 10R to 3M01 47R to 2M13 10R to 3M01 10R to 3M01 24; 96 24; 192 24; 96 24; 192 47R to 2M13 10R to 4M99 10R to 4M99 47R to 1M0 10R to 4M99 10R to 4M99 47R to 1M0 10R to 8M87 10R to 8M87 47R to 1M0 10R to 8M87 10R to 8M87 47R to 1M0 24; 96 24; 192 24; 96 24; 192 24; 96 24; 192 24; 96 24; 192 PART NUMBER AND PRODUCT DESCRIPTION Part Number: TNPW12061K32DETA T N P W 1 2 0 6 1 K 3 2 D E T A TYPE/SIZE RESISTANCE TOLERANCE TCR PACKAGING SPECIAL TNPW0402 TNPW0603 TNPW0805 TNPW1206 TNPW1210 TNPW2010 TNPW2512 R = Decimal K = Thousand M = Million (4 digits) B = 0.1 % D = 0.5 % F = 1.0 % H = 50 ppm/K E = 25 ppm/K X = 15 ppm/K Y = 10 ppm/K TA TD CN TY TC Up to 2 digits Blank = Standard Product Description: TNPW-1206 1.32K 0.5 % T-9 RT1 TNPW-1206 1.32K 0.5 % T-9 RT1 TYPE TNPW-0402 TNPW-0603 TNPW-0805 TNPW-1206 TNPW-1210 TNPW-2010 TNPW-2512 RESISTANCE Examples: 1K32 = 1320 99.68K = 99 680 360 = 360 TOLERANCE 0.1 % 0.5 % 1.0 % TCR T-2 = 50 ppm/K T-9 = 25 ppm/K T-10 = 15 ppm/K T-13 = 10 ppm/K PACKAGING RT1 RT7 R52 R75 RT6 Note * The product can be ordered using either the PART NUMBER or the PRODUCT DESCRIPTION. * For ordering TNPW e3 with lead free terminations please refer to latest edition of datasheet TNPW e3, document number 28758. Document Number: 31006 Revision: 31-Jan-12 For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 347 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW High Stability Thin Film Chip Resistors Vishay PACKAGING TYPE TNPW0402 TNPW0603 TNPW0805 TNPW1206 TNPW1210 TNPW2010 TNPW2512 CODE QUANTITY RT7 = TD 10 000 R52 = CN 1000 (1) RT1 = TA 5000 RT6 = TC 20 000 R75 = TY 1000 CARRIER TAPE Paper tape acc. IEC 60286-3 Type I WIDTH PITCH 8 mm 2 mm REEL DIAMETER 180 mm/7" 8 mm 4 mm 330 mm/13" Blister tape acc. IEC 60286-3 Type II 12 mm 4 mm 180 mm/7" Note (1) 1000 pieces packaging is available only for precision resistors with tolerance 0.1 % and temperature coefficient 25 ppm/K. DESCRIPTION ASSEMBLY Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade ceramic substrate and conditioned to achieve the desired temperature coefficient. A special laser is used to achieve the target value by smoothly cutting a meander groove in the resistive layer without damaging the ceramics. A further conditioning is applied in order to stabilize the trimming result. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The result of the determined production is verified by an extensive testing procedure on 100 % of the individual chip resistors. This includes pulse load screening for the elimination of products with a potential risk of early life failures according to EN 140401-801, 2.1.2.2. Only accepted products are laid directly into the tape in accordance with EN 60286-3. The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow or vapour phase as shown in IEC 61760-1. The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. Solderability is specified for 2 years after production or re-qualification. The permitted storage time is 20 years. RELATED PRODUCTS The lead free version TNPW e3 can be used as drop in replacement for the TNPW whenever lead bearing terminations are not mandatory. For ordering TNPW e3 please refer to latest edition of datasheet TNPW e3, document number 28758. TNPS .... ESCC high-reliability thin film chip resistors are the premium choice for design and manufacture of equipment, where matured technology and proven reliability are of utmost importance. They are regularly used in communication and research satellites and fit equally well into aircraft and military electronic systems. Approval of the TNPS .... ESCC products is granted by the European Space Components Coordination and registered in the ESCC Qualified Parts List, REP005, document number 28789. www.vishay.com 348 For technical questions, contact: thinfilmchip@vishay.com Document Number: 31006 Revision: 31-Jan-12 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW Current Noise in V/V Non-Linearity A3 in dB High Stability Thin Film Chip Resistors 120 TNPW1206 110 TNPW0805 TNPW0603 TNPW0402 100 90 Vishay 3 2 1 TNPW0402 0.5 TNPW0603 0.3 TNPW0805 TNPW1206 0.1 80 0.05 0.03 70 60 10 100 1K 10K 100K Resistance Value in Non-Linearity 0.01 100 10K 100K 1M Resistance Value in Current Noise 60 60 [Z]-RO in % RO Phase Angle in 1K TNPW0603 40 20 10 0 TNPW0603 40 20 10 0 100 1 k 100 - 20 - 20 1 k - 40 - 40 4.75 k - 60 4.75 k - 60 10 k - 80 1 5 10 50 100 10 k 500 1000 Frequency f in MHz 1 5 10 50 100 500 1000 Frequency f in MHz HF Performance 60 60 TNPW0805 [Z]-RO in % RO Phase Angle in HF Performance - 80 40 20 10 0 100 TNPW0805 40 20 10 100 1 k 0 - 20 - 20 1 k - 40 - 40 - 60 - 80 - 60 10 k 1 5 10 HF Performance Document Number: 31006 Revision: 31-Jan-12 50 100 500 1000 Frequency f in MHz 10 k - 80 1 5 10 50 100 500 1000 Frequency f in MHz HF Performance For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 349 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW Temperature Rise in K 90 80 0402 0603 0805 1206 1210 2010 2512 70 60 50 Rated Power in % High Stability Thin Film Chip Resistors Vishay 120 100 80 60 40 30 40 20 20 10 EN 0 0.1 0 0.2 0.3 0.4 0.5 0.6 0 - 55 0.7 - 25 0 25 50 Power in W 3K TNPW0805 1K TNPW0603 100 10 10R 100R 1K TNPW0805 1K TNPW0603 10 10R 10K 100K Resistance Value in 100 TNPW0805 10 TNPW0603 1 0.1 100R 1K 10K 100K Resistance Value in Single-Pulse High Voltage Overload Test 10/700 s EN 140000 4.27 Power Rating P in W Power Rating P in W 3K 100 Single-Pulse High Voltage Overload Test 1.2/50 s EN 140000 4.27 0.01 75 100 125 150 175 Ambient Temperature in C Derating Test Voltage in V Test Voltage in V Temperature Rise 70 100 TNPW0805 10 TNPW0603 1 0.1 Secondary conditions: a) P > 0 (peak pulse, single pulse) b) u 70 C c) U max. see diagram (max. pulse voltage) 10-5 10-4 10-3 Pulse Rating P 0 www.vishay.com 350 10-2 Secondary conditions: a) P P70 (permissible constant power at u = 70 C) b) u 70 C c) Umax. see diagram (max. pulse voltage) 10-1 1 10 Square Pulse ti in s 0.01 10-5 10-4 10-3 10-2 10-1 1 10 Square Pulse ti in s Pulse Rating P P70 For technical questions, contact: thinfilmchip@vishay.com Document Number: 31006 Revision: 31-Jan-12 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW Pulse Voltage Umax. in V High Stability Thin Film Chip Resistors Vishay 500 TNPW0805 400 TNPW0603 300 200 100 Secondary conditions: a) P see diagram (Pulse Rating) b) u 70 C 0 10-5 10-4 10-3 10-2 10-1 1 10 Square Pulse ti in s Maximum Pulse Voltage TEST AND REQUIREMENTS All tests are carried out in accordance with the following specifications: IEC 60115-1, generic specification (includes tests) EN 140400, sectional specification (includes schedule for qualification approval) EN 140401-801, detail specification (includes schedule for conformance inspection) The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5202. The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated Document Number: 31006 Revision: 31-Jan-12 temperature range: Lower category temperature, upper category temperature; damp heat, long term, 56 days) is valid. Unless otherwise specified the following values apply: Temperature: 15 C to 35 C Relative humidity: 45 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). The components are mounted for testing on boards in accordance with EN 60115-1, 4.31 unless otherwise specified. The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140401-801. For technical questions, contact: thinfilmchip@vishay.com www.vishay.com 351 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TNPW High Stability Thin Film Chip Resistors Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 IEC 60068-2 CLAUSE TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) Stability for product types: TNPW0402 100 to 100 k 10 to 100 k TNPW0603 100 to 332 k 10 to 332 k 100 to 1 M 10 to 1 M 100 to 2 M 10 to 2 M TNPW1210 100 to 3.01 M 10 to 3.01 M TNPW2010 100 to 4.99 M 10 to 4.99 M TNPW2512 100 to 8.87 M 10 to 8.87 M TNPW0805 TNPW1206 4.5 4.8.4.2 4.25.1 - Resistance - Temperature coefficient - Endurance at 70 C 10 to < 100 0.1 % At (20/- 55/20) C and (20/125/20) C 0.5 %; 1.0 % 50 ppm/K; 25 ppm/K; 15 ppm/K; 10 ppm/K U = P 70 x R or Umax.; 1.5 h on; 0.5 h off; 70 C; 1000 h (0.1 % R + 0.02 ) (0.05 % R + 0.01 ) (0.25 % R + 0.05 ) 4.25.3 - Endurance at upper category temperature 125 C; 1000 h (0.1 % R + 0.02 ) (0.05 % R + 0.01 ) (0.5 % R + 0.05 ) 4.13 - Short time overload U = 2.5 x P 70 x R 2 x Umax.; 5 s (0.05 % R + 0.01 ) (0.02 % R + 0.01 ) (0.1 % R + 0.02 ) 4.19 14 (Na) Rapid change of temperature 30 min at LCT: 30 min at UCT; LCT = - 55 C; UCT = 125 C; 5 cycles (0.05 % R + 0.01 ) (0.02 % R + 0.01 ) (0.1 % R + 0.02 ) 4.24 78 (Cab) Damp heat steady state (402) C; 56 days; (93 3) % RH (0.1 % R + 0.02 ) (0.05 % R + 0.01 ) (0.5 % R + 0.05 ) 58 (Td) Resistance to soldering heat 4.18.2 www.vishay.com 352 Solder bath method; (260 5) C; (0.05 % R + 0.01 ) (0.02 % R + 0.01 ) (0.1 % R + 0.02 ) (10 1) s For technical questions, contact: thinfilmchip@vishay.com Document Number: 31006 Revision: 31-Jan-12 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000