September 2017
RF Components
Balun transformers
Wound SMD
ATB series
ATB2012E-20011 (2.01.20.6mm)
ATB2012-50011 (2.01.21.2mm)
ATB2012E-50011M (2.01.21.0mm)
ATB2012E-50012M (2.01.21.0mm)
ATB2012-75011 (2.01.21.2mm)
ATB2012E-75011M (2.01.21.0mm)
(2/16)
20170912 / rf_balun_atb2012_en.fm
RF Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using this products.
The storage period is less than 6 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip-
ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip-
ment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual-
ity require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society,
person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment  
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro-
tection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
Balun transformers
Wound SMD
FEATURES
The ATB2012 case size is L2.0×W1.2.
The case size is smaller than conventional Baluns.
Low insertion loss and good balance parameters.
Conforms to the RoHS Directive.
APPLICATION
TV and mobile device tuners (DVB-T/H, ISDB-T, etc.)
STB / tuner power divider
NFC (Near Field Communication)
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Operating temperature range includes self-temperature rise.
The storage temperature range is for after the assembly.
Overview of the ATB series
ATB 2012 E -200 11 -T06
Series name L x W dimensions Internal
code
Input impedance Impedance ratio Packaging style Internal code
(mm) ()
2012 2.0×1.2 E 200 20 11 1:1 T ø180mm reel
ATB 2012 -500 11 -T000
Series name L x W dimensions Input impedance Impedance ratio Packaging style Internal code
(mm) ()
2012 2.0×1.2 500 50 11 1:1 T ø180mm reel
750 75
ATB 2012 E -500 11 M -T01
Series name L x W dimensions Internal
code
Input impedance Impedance ratio Product
internal Packaging style Internal
code
(mm) ()
2012 2.0×1.2 E 500 50 11 1:1 M T ø180mm reel
750 75 12 1:2
Type
Temperature range
Reel diameter Package quantity
(pieces/reel)
Individual weight
mg
Operating
temperature
(°C)
Storage
temperature
(°C)
ATB2012E-20011 –40 to +85 –40 to +85 ø180mm 4000 5
ATB2012-50011 –40 to +85 –40 to +85 ø180mm 2000 8
ATB2012E-50011M
ATB2012E-50012M –40 to +85 –40 to +85 ø180mm 2000 8
ATB2012-75011 –40 to +85 –40 to +85 ø180mm 2000 8
ATB2012E-75011M –40 to +85 –40 to +85 ø180mm 2000 8
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details. https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
Overview of the ATB series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 10 to 30s 245°C 5s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series
ATB2012E-20011 type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
1.2±0.2
41
32
2.0±0.2
1.2 0.40.4
1.2±0.2
0.65max.0.30.30.05
0.5
1
2
4
3
2.0±0.2
Dimensions in mm
Dimensions in mm
1.1
0.8
2.6
0.4
(6/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB seriesATB2012E-20011 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
FREQUENCY CHARACTERISTICS
INSERTION LOSS
CMRR
RETURN LOSS
PHASE BALANCE
Measurement equipment
Equivalent measurement equipment may be used.
Frequency
range
(MHz)
UB/B
impedance
()
Insertion
loss
(dB)max.
CMRR
typ.
DC
resistance
()max.
Rated
current
(mA)
Rated
voltage
(V)
Insulation
resistance
(M)min.
Part No.
13.56 20/20 1.0 20 1.5 150 20 10 ATB2012E-20011-T06
0 5 10 15 20
Frequency(MHz)
5.0
4.0
3.0
1.0
2.0
0.0
Insertion loss(dB)
Frequency(MHz)
30
40
60
70
10
20
50
0
80
CMRR
0 5 10 15 20
30
15
10
25
20
5
0
Return loss(dB)
0 5 10 15 20
Frequency(MHz)
Frequency(MHz)
185
177
179
180
182
178
176
181
183
175
184
Phase balance(deg.)
0 5 10 15 20
Measurement item Product No. Manufacturer
DC resistance 4338A Keysight Technologies
Insulation resistance 4339A Keysight Technologies
Insertion loss E5071B Keysight Technologies
Return loss E5071B Keysight Technologies
Amplitude imbalance E5071B Keysight Technologies
Phase balance E5071B Keysight Technologies
(7/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series
ATB2012-50011 type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
2.0±0.2
1.2±0.21.2±0.1
0.4 1.2 0.4
0.35 0.5 0.35
41
32
0.4
Dimensions in mm
1.2
2.7
0.4
0.8
1
2
4
3
Unbalanced Port
50Ω
Balanced Port
50Ω
(25Ω)
(25Ω)
(8/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB seriesATB2012-50011 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
FREQUENCY CHARACTERISTICS
INSERTION LOSS
AMPLITUDE IMBALANCE
RETURN LOSS
PHASE BALANCE
Measurement equipment
Equivalent measurement equipment may be used.
Frequency
range
(MHz)
UB/B
impedance
()
Insertion loss
(dB) CMRR
typ.
DC
resistance
()max.
Rated
current
(mA)
Rated
voltage
(V)
Insulation
resistance
(M)min.
Withstanding
voltage
(V)
Part No.
typ. max.
40 to 860 50/50 1.0 2.5 20 1.0 200 20 10 125 ATB2012-50011-T000
0 100 400 500 600 700 800 900 1000200 300
Frequency(MHz)
6.0
4.0
3.0
1.0
5.0
2.0
0.0
Insertion loss(dB)
Frequency(MHz)
3.0
1.0
4.0
2.0
5.0
0
Amplitude imbalance(dB)
0 100 400 500 600 700 800 900 1000200 300
Frequency(MHz)
35
30
15
10
25
20
5
0
Return loss(dB)
0 100 400 500 600 700 800 900 1000200 300
Frequency(MHz)
175
177
179
180
182
178
176
181
183
185
184
Phase balance(deg.)
0 100 400 500 600 700 800 900 1000200 300
Measurement item Product No. Manufacturer
DC resistance 4338A Keysight Technologies
Insulation resistance 4339A Keysight Technologies
Insertion loss E5071B Keysight Technologies
Return loss E5071B Keysight Technologies
Amplitude imbalance E5071B Keysight Technologies
Phase balance E5071B Keysight Technologies
(9/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series
ATB2012E-50011M type
ATB2012E-50012M type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
1.2±0.21.0±0.1
0.5
0.4 1.2 0.4
0.3 0.3
2.0±0.2
41
32
1.2
2.7
0.4
0.8
1
2
4
3
Unbalanced Port
50
Balanced Port
50Ω
(25Ω)
(25Ω)
Dimensions in mm
ATB2012E-50011M type
1
2
4
3
Unbalanced Port
50
Balanced Port
100Ω
(50Ω)
(50Ω)
ATB2012E-50012M type
(10/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series ATB2012E-50011M type
ATB2012E-50012M type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Frequency
range
(MHz)
UB/B
impedance
()
Insertion loss
(dB) CMRR
typ.
DC
resistance
()max.
Rated
current
(mA)
Rated
voltage
(V)
Insulation
resistance
(M)min.
Withstanding
voltage
(V)
Part No.
typ. max.
400 to 1800 50/50 1.0 2.2 15 0.5 150 20 10 125 ATB2012E-50011M-T01
400 to 1800 50/100 1.0 2.5 15 0.5 150 20 10 125 ATB2012E-50012M-T01
(11/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series ATB2012E-50011M type
ATB2012E-50012M type
FREQUENCY CHARACTERISTICS
ATB2012E-50011M type
INSERTION LOSS
AMPLITUDE IMBALANCE
RETURN LOSS
PHASE BALANCE
ATB2012E-50012M type
INSERTION LOSS
AMPLITUDE IMBALANCE
RETURN LOSS
PHASE BALANCE
Measurement equipment
Equivalent measurement equipment may be used.
0 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
Insertion loss(dB)
0
1
2
3
4
5
6
Amplitude imbalance(dB)
0 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
0
1
2
3
4
5
6
7
8
9
10
0
5
10
15
20
25
30
35
40
450 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
Return loss(dB)
Phase balance(deg.)
0 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
160
165
170
175
180
185
190
195
200
0 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
Insertion loss(dB)
0
1
2
3
4
5
6
Amplitude balance(dB)
0 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
0
1
2
3
4
5
6
7
8
0
5
10
15
20
25
30
35
400 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
Return loss(dB)
Phase balance(deg.)
0 200 800
1000 1200 1400 1600 1800
400 600
Frequency(MHz)
0
20
40
60
80
140
120
100
160
180
200
Measurement item Product No. Manufacturer
DC resistance 4338A Keysight Technologies
Insulation resistance 4339A Keysight Technologies
Insertion loss E5071B Keysight Technologies
Return loss E5071B Keysight Technologies
Amplitude imbalance E5071B Keysight Technologies
Phase balance E5071B Keysight Technologies
(12/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series
ATB2012-75011 type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
2.0±0.2
1.2±0.2
0.4 1.2 0.4
0.35 0.5 0.35
41
32
0.4
1.2 ±0.1
Dimensions in mm
1.2
2.7
0.4
0.8
1
2
4
3
1
2
4
3
Unbalanced Port
75Ω
Balanced Port
75Ω
(37.5Ω)
(37.5Ω)
(13/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB seriesATB2012-75011 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
FREQUENCY CHARACTERISTICS
INSERTION LOSS
AMPLITUDE IMBALANCE
RETURN LOSS
PHASE BALANCE
Measurement equipment
Equivalent measurement equipment may be used.
Frequency
range
(MHz)
UB/B
impedance
()
Insertion loss
(dB) CMRR
typ.
DC
resistance
()max.
Rated
current
(mA)
Rated
voltage
(V)
Insulation
resistance
(M)min.
Withstanding
voltage
(V)
Part No.
typ. max.
50 to 1200 75/75 0.8 1.2 20 0.7 280 20 10 125 ATB2012-75011-T000
0 400 600 800 1000 1200200
Frequency (MHz)
6.0
4.0
3.0
1.0
5.0
2.0
0.0
Insertion loss (dB)
Frequency(MHz)
1.0
–1.0
0
2.0
–2.0
3.0
–3.0
Amplitude imbalance(dB)
0 400 600 800 1000 1200200
Frequency (MHz)
40
35
30
15
10
25
20
5
0
0 400 600 800 1000 1200200
Return loss(dB)
Frequency(MHz)
170
174
178
184
176
172
182
180
186
190
188
Phase balance(deg.)
0 400 600 800 1000 1200200
Measurement item Product No. Manufacturer
DC resistance 4338A Keysight Technologies
Insulation resistance 4339A Keysight Technologies
Insertion loss E5071B Keysight Technologies
Return loss E5071B Keysight Technologies
Amplitude imbalance E5071B Keysight Technologies
Phase balance E5071B Keysight Technologies
(14/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series
ATB2012E-75011M type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
1.2±0.21.0±0.1
0.5
0.4 1.2 0.4
0.3 0.3
2.0±0.2
41
32
Dimensions in mm
1.2
2.7
0.4
0.8
1
2
4
3
1
2
4
3
Unbalanced Port
75Ω
Balanced Port
75Ω
(37.5Ω)
(37.5Ω)
(15/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB seriesATB2012E-75011M type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
FREQUENCY CHARACTERISTICS
INSERTION LOSS
AMPLITUDE IMBALANCE
RETURN LOSS
PHASE BALANCE
Measurement equipment
Equivalent measurement equipment may be used.
Frequency
range
(MHz)
UB/B
impedance
()
Insertion loss
(dB) CMRR
typ.
DC
resistance
()max.
Rated
current
(mA)
Rated
voltage
(V)
Insulation
resistance
(M)min.
Withstanding
voltage
(V)
Part No.
typ. max.
400 to 1800 75/75 1.0 2 15 0.5 150 20 10 125 ATB2012E-75011M-T01
0 200 800
1000 1200 1400 1500 1800
400 600
Frequency(MHz)
Insertion loss(dB)
0
1
2
3
4
5
6
Amplitude imbalance(dB)
0 200 800
1000 1200 1400 1500 1800
400 600
Frequency(MHz)
0
1
2
3
4
5
6
7
8
9
10
0 200 800
1000 1200 1400 1500 1800
400 600
Frequency(MHz)
0
5
10
15
20
25
30
35
40
Return loss(dB)
0 200 800
1000 1200 1400 1500 1800
400 600
Frequency(MHz)
160
165
170
175
180
185
190
195
200
Phase balance(deg.)
Measurement item Product No. Manufacturer
DC resistance 4338A Keysight Technologies
Insulation resistance 4339A Keysight Technologies
Insertion loss E5071B Keysight Technologies
Return loss E5071B Keysight Technologies
Amplitude imbalance E5071B Keysight Technologies
Phase balance E5071B Keysight Technologies
(16/16)
20170912 / rf_balun_atb2012_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
RF Components
ATB series
Packaging style
REEL DIMENSIONS
TAPE DIMENSIONS
Typ e A W1 W2 N
ATB2012E-20011 ø180 13 60 9
ATB2012-50011 ø180 13 60 9
ATB2012E-50011M
ATB2012E-50012M ø180 13 60 9
ATB2012-75011 ø180 13 60 9
ATB2012E-75011M ø180 13 60 9
Dimensions in mm
Ty p e A B øD0 E F P0 P1 P2 W K t
ATB2012E-20011 1.45±0.1 2.25±0.1 1.55±0.05 1.75±0.1 3.50±0.05 4.0±0.1 4.0±0.1 2.0±0.05 8.0±0.20 0.75±0.05 0.25±0.05
ATB2012-50011 1.4±0.1 2.3±0.1 1.5+0.1/0 1.75±0.1 3.5±0.1 4.0±0.1 4.0±0.1 2.0±0.1 8.0±0.1 1.4±0.1 0.25±0.05
ATB2012E-50011M
ATB2012E-50012M 1.4±0.1 2.3±0.1 1.5+0.1/0 1.75±0.1 3.5±0.1 4.0±0.1 4.0±0.1 2.0±0.1 8.0±0.1 1.15±0.1 0.2±0.05
ATB2012-75011 1.4±0.1 2.3±0.1 1.5+0.1/0 1.75±0.1 3.5±0.1 4.0±0.1 4.0±0.1 2.0±0.1 8.0±0.1 1.4±0.1 0.25±0.05
ATB2012E-75011M 1.4±0.1 2.3±0.1 1.5+0.1/0 1.75±0.1 3.5±0.1 4.0±0.1 4.0±0.1 2.0±0.1 8.0±0.1 1.15±0.1 0.2±0.05
ø13.0±0.2
ø21.0±0.8
N
2.0±0.5
A
Dimensions in mm
1.0
W2
W1
t
W
FE
P0
P1
P2
øD0
B
AK
Dimensions in mm
160min. Taping 440min.
Drawing direction
500 to 560min.
Marking ( Notch)
ATB2012-50011
ATB2012E-50011M
ATB2012E-50012M
ATB2012-75011
ATB2012E-75011M
ATB2012E-20011